In-situ gas contents of a multi-section coal seam in Sydney basin for coal and gas outburst management

The gas content is crucial for evaluating coal and gas outburst potential in underground coal mining. This study focuses on investigating the in-situ coal seam gas content and gas sorption capacity in a representative coal seam with multiple sections (A1, A2, and A3) in the Sydney basin, where the CO_(2) composition exceeds 90%. The fast direct desorption method and associated devices were described in detail and employed to measure the in-situ gas components (Q_(1), Q_(2), and Q_(3)) of the coal seam. The results show that in-situ total gas content (Q_(T)) ranges from 9.48 m^(3)/t for the A2 section to 14.80 m^(3)/t for the A3 section, surpassing the Level 2 outburst threshold limit value, thereby necessitating gas drainage measures. Among the gas components, Q_(2) demonstrates the highest contribution to Q_(T), ranging between 55% and 70%. Furthermore, high-pressure isothermal gas sorption experiments were conducted on coal samples from each seam section to explore their gas sorption capacity. The Langmuir model accurately characterizes CO_(2) sorption behavior, with ft coefcients (R^(2)) greater than 0.99. Strong positive correlations are observed between in-situ gas content and Langmuir volume, as well as between residual gas content (Q_(3)) and sorption hysteresis. Notably, the A3 seam section is proved to have a higher outburst propensity due to its higher Q_(1) and Q_(2) gas contents, lower sorption hysteresis, and reduced coal toughness f value. The insights derived from the study can contribute to the development of efective gas management strategies and enhance the safety and efciency of coal mining operations.

A rapid and accurate direct measurement method of underground coal seam gas content based on dynamic diffusion theory

Coal seam gas content is frequently measured in quantity during underground coal mining operation and coalbed methane(CBM)exploration as a significant basic parameter.Due to the calculation error of lost gas and residual gas in the direct method,the efficiency and accuracy of the current methods are not inadequate to the large area multi-point measurement of coal seam gas content.This paper firstly deduces a simplified theoretical dynamic model for calculating lost gas based on gas dynamic diffusion theory.Secondly,the effects of various factors on gas dynamic diffusion from coal particle are experimentally studied.And sampling procedure of representative coal particle is improved.Thirdly,a new estimation method of residual gas content based on excess adsorption and competitive adsorption theory is proposed.The results showed that the maximum error of calculating the losing gas content by using the new simplified model is only 4%.Considering the influence of particle size on gas diffusion law,the particle size of the collected coal sample is below 0.25 mm,which improves the measurement speed and reflects the safety representativeness of the sample.The determination time of gas content reduced from 36 to 3 h/piece.Moreover,the absolute error is 0.15–0.50 m^3/t,and the relative error is within 5%.A new engineering method for determining the coal seam gas content is developed according to the above research.

New technology of determining coalbed gas content by reversion seal coring

The key of the direct method of determining coalbed gas content is how to shorten the coal core exposure time in the sampling progress and reduce measuring error of gas content which comes from the calculation of losing gas content. The coring tests were carried out in No.24 drilling field of 715 floor gateway in Qinan Coal Mine by using traditional drill core bar- rel sampler and self-designed reversion seal coring equipment. The losing gas content was calculated by power functional method, and the gas content of two coring methods was determined, respectively. Results show that, compared with traditional drill core barrel sampling, the newly seal coring equipment can significantly shorten the coal core exposure time, the 30 min desorption gas content increases obviously, the calculation of losing gas content reduces by 56.99%, the desorption gas content in normal atmosphere increases by 113.24%, and the determining value of gas content increases by 10.06%. The new technol- ogy has much higher accuracy, and it is worthwhile to be popularized.

Advances in gas content based on outburst control technology in Huainan, China

The sudden and violent nature of coal and gas outbursts continues to pose a serious threat to coal mine safety in China. One of the key issues is to predict the occurrence of outbursts. Current methods that are used for predicting the outbursts in China are considered to be inadequate, inappropriate or impractical in some seam conditions. In recent years, Huainan Mining Industry Group(Huainan) in China and the Commonwealth Scientific and Industrial Research Organisation(CSIRO) in Australia have been jointly developing technology based on gas content in coal seams to predict the occurrence of outbursts in Huainan. Significant progresses in the technology development have been made, including the development of a more rapid and accurate system in determining gas content in coal seams, the invention of a sampling-while-drilling unit for fast and pointed coal sampling, and the coupling of DEM and LBM codes for advanced numerical simulation of outburst initiation and propagation. These advances are described in this paper.

Influence of Ground Stress on Coal Seam Gas Pressure and Gas Content

The influence of ground stress was quantitatively analyzed on coal seam gas pressure and gas content in this paper.Mining activities in coal mine can result in stress concentration in the coal(rock)body around the mining space,but porosity of the coal seam would not change too much.Therefore,gas pressure and gas content in the coal seam are slightly affected.Studies showed that the free gas was gradually transformed into adsorbed gas,and the gas adsorption volume was small,and then gas pressure increases roughly linearly when the porosity decreased because of stress influence.Additionaly,when porosity of coal seam reduced to 40%,the amount of adsorbed gas accounted for no more than 10%of coal seam gas content,and the increase of gas pressure did not exceed 15%of the original gas pressure.

Forward modeling and inversion of the relation model between the gas content of plume and its seismic attribute

The methane bubble plume attracts interest because it offers direct evidence of seafloor gas leakage and plays an indirect role in the exploration and identification of natural gas hydrate.In this study,based on established plume models and their migration sections,three amplitude-class attributes were extracted from three formations for the migration sections of five plumes,and the correlation between the gas content and seismic attribute was obtained.As the gas content increases,the amplitude attribute correspondingly increases,and the linear correlation is relatively good.Moreover,correlation coefficients between gas content and amplitude attributes are close to 1.0.By using linear fitting,the relation model between the gas content of the plume and the seismic attribute was obtained.The relation model was subsequently used to invert the gas content from a real databearing plume.Comparison of the gas content section of the plume with the attribute section and real seismic section reveals common distribution characteristics,namely,the color of the section in the lower right corner is dark.If the amplitude value is large in the seismic section of the real plume,the amplitude attribute value is also large in the corresponding attribute section,and the inverted value of the gas content is also large(because gas content and amplitude are linearly correlated),which indicates that the plume bubbles of the section in the lower right corner is intensively distributed.Finally,the obtained gas content section of the plume can reflect the distribution of the plume bubble content more simply and intuitively,from which the distribution law of seafloor bubbles can be deduced,and this lays a foundation for the further estimation of the gas content of the plume and hydrate reserves.

Calculation of gas content in coal seam influenced by in-situ stress grads and ground temperature

On the basis of the analysis of coal bed gas pressure in deep mine, and the coal bed permeability ( k ) and the characteristic of adsorption parameter ( b ) changing with temperature, the author puts forward a new calculating method of gas content in coal seam influenced by in situ stress grads and ground temperature. At the same time, the contrast of the measuring results of coal bed gas pressure with the computing results of coal bed gas pressure and gas content in coal seam in theory indicate that the computing method can well reflect the authenticity of gas content in coal seam,and will further perfect the computing method of gas content in coal seam in theory,and have important value in theory on analyzing gas content in coal seam and forecasting distribution law of gas content in coal seam in deep mine.

Direct fitting measurement of gas content in coalbed and selection of reasonable sampling time

In this study, we selected 9 typical coal samples with different metamorphic grades as the study subjects,measured their initial 30-min gas desorption at 30℃ and different pressure using a self-developed gas adsorption/desorption device. Based on the characteristics of gas desorption from coal samples, we proposed a direct fitting method for measurement of gas content in coalbed, analyzed the effects of sampling time on the measurement results and determined the reasonable sampling time of coal samples with different metamorphic grades at different gas adsorption pressure at equilibrium. The results show that (1)the error of gas contents obtained using the direct fitting method relative to that obtained using indirect method is less than 10%, which meets the actual on-site requirements and verifies the feasibility of the direct fitting method;(2) when the relative error is controlled within ±10%, the reasonable sampling time of coal samples is linearly related to the gas adsorption pressure at equilibrium;(3) the reasonable sampling time of coal samples with the same metamorphic grade exhibits a shortening trend with increasing gas adsorption pressure at equilibrium;(4) for coal samples with similar gas adsorption pressure at equilibrium, the reasonable sampling time of coal samples displays a shortening trend with increasing metamorphic grade. Overall, the study provides a basis for improving the measurement accuracy of gas content in coalbed.

Analysis and verification of gas content and pressure change rate characteristics in hydraulic system

Gas content of the hydraulic system directly affects the rate of pressure change of the hydraulic system. The purpose of this paper is to establish a mathematical model of oil gas content, hydraulic system pressure and pressure rise rate, obtain corresponding oil pressure value when the pressure rise rate of different gas content is maximum, and verify the accuracy of this conclusion by the FLUENT simulation software. On this basis, a rapid pressure building device of the hydraulic system is developed and designed. The above oil pressure value is used as the working cut-off pressure of the rapid pressure building device, and then the hydraulic oil pump continues to pressurize to the highest working pressure required by the system. The research content can replace the hydraulic system from the initial low pressure to the rapid pressure build-up of the oil, thus increasing the construction pressure of the hydraulic system. The research results show that the rapid pressure building device effectively reduces the time for the hydraulic system to establish pressure. Through the analysis of theoretical derivation and the collected experimental data, the error is about 5.9%, which verifies the correctness of the theoretical formula.

Influencing factors of gas content evaluation for shale gas:a case study of Lower Paleozoic Wuling fold belt in Upper Yangtze Basin

Factors of shale gas accumulation can be divided into the external and internal factors,according to accumulation mechanism and characteristics of shale gas. The internal factors mainly refer to parameters of organic geochemistry,mineral components and physical parameters. Six factors were presented in this study,i. e.organic matter,maturity,quartz,carbonate,clay mineral and pore. The external factors mainly refer to geologic environment of shale gas reservoir,including four factors: temperature,pressure,depth and thickness.Based on the experiment results of 26 samples of drilling cores from Wuling fold belt in Lower Paleozoic Silurian of the Upper Yangtze Basin,combined with the integrated analysis of geology,logging and test,the correlation of the gas content of shale gas to the above-mentioned ten factors was concluded. Six important evaluation indicators were preliminarily established in the gas-bearing core area of marine shale in the Upper Yangtze Basin.

Model Prediction and Optimal Control of Gas Oxygen Content for A Municipal Solid Waste Incineration Process

In the municipal solid waste incineration process,it is difficult to effectively control the gas oxygen content by setting the air flow according to artificial experience.To address this problem,this paper proposes an optimization control method of gas oxygen content based on model predictive control.First,a stochastic configuration network is utilized to establish a prediction model of gas oxygen content.Second,an improved differential evolution algorithm that is based on parameter adaptive and t-distribution strategy is employed to address the set value of air flow.Finally,model predictive control is combined with the event triggering strategy to reduce the amount of computation and the controller's frequent actions.The experimental results show that the optimization control method proposed in this paper obtains a smaller degree of fluctuation in the air flow set value,which can ensure the tracking control performance of the gas oxygen content while reducing the amount of calculation.

Comparing potentials for gas outburst in a Chinese anthracite and an Australian bituminous coal mine

Gas outbursts in underground mining occur under conditions of high gas desorption rate and gas content,combined with high stress regime, low coal strength and high Young's modulus. This combination of gas and stress factors occurs more often in deep mining. Hence, as the depth of mining increases, the potential for outburst increases. This study proposes a conceptual model to evaluate outburst potential in terms of an outburst indicator. The model was used to evaluate the potential for gas outburst in two mines, by comparing numerical simulations of gas flow behavior under typical stress regimes in an Australian gassy mine extracting a medium-volatile bituminous coal, and a Chinese gassy coal mine in Qinshui Basin(Shanxi province) extracting anthracite coal. We coupled the stress simulation program(FLAC3D) with the gas simulation program(SIMED II) to compute the stress and gas pressure and gas content distribution following development of a roadway into the targeted coal seams. The data from gas content and stress distribution were then used to quantify the intensity of energy release in the event of an outburst.

Degassing effect of ultrasonic vibration in molten melt and semi-solid slurry of Al-Si alloys

In the process of semi-solid slurry preparation with direct ultrasonic vibration (UV) by dipping the horn into the melt, one of the questions is whether the gas content in the melt would be increased or not by the cavitation effect of ultrasonic vibration. By application of quantitative gas content measurement technique, this paper investigated the effect of the ultrasonic vibration on the gas content of both the melt and the semi-solid slurry of Al-Si alloys, and the variations of the gas contents in two kinds of aluminum alloys, i.e., A356 alloy and Al-20Si-2Cu-1Ni-0.6RE alloy (Al-20Si for short). The results show that ultrasonic vibration has an obvious degassing effect on the molten melt, especially on the semi-solid slurry of Al-Si alloy which is below the liquidus temperature by less than 20 ℃. The ultrasonic degassing efficiency of the A356 alloy decreases with the reduction of the initial gas content in the melt, and it is nearly unchanged for the Al-20Si alloy. The gas content of both alloys decreases when the ultrasonic vibration time is increased. The best vibration time for Al-20Si alloy at the liquid temperature of 710 ℃ and semi-solid temperature of 680 ℃ is 60 s and 90 s, respectively; and the degassing efficiency is 48% and 35%, respectively. The mechanism of ultrasonic degassing effect is discussed.

Greenhouse gas emissions from shallow uncovered coal seams

This study discusses a method of quantifying emissions from surface coal mining that has been trialled in Australia. The method is based on direct measurement of surface emissions from uncovered coal seams in mine pits, concurrent measurement of residual gas content of blasted coal in mine pits, and measurement of pre-mining gas content of the same seam from cores retrieved from exploration boreholes drilled away from active mining. The results from one of the mines studied are presented in this paper. In this mine,the pre-mining gas content of the target seam was measured using cores from an exploration borehole away from active mining. Gas content varied from 0.7 to 0.8 m3/t and gas composition varied from16% to 21% CH4(84–79% CO2). In-pit measurements included seam surface emissions and residual gas content of blasted and ripped coal. Residual gas content varied from 0.09 to 0.15 m3/t, less than twofold across the mine pit. Composition of the residual gas was in general 90% CO2and 10% CH4, with slight variation between samples. Coal seam surface emissions varied from 1.03 to 7.50 mL of CO2-e per minute and per square meter of the coal seam surface, a sevenfold variation across the mine pit.

Gas diffusion in a cylindrical coal sample – A general solution,approximation and error analyses

The analytical mathematical solutions of gas concentration and fractional gas loss for the diffusion of gas in a cylindrical coal sample were given with detailed mathematical derivations by assuming that the diffusion of gas through the coal matrix is concentration gradient-driven and obeys the Fick’s Second Law of Diffusion.The analytical solutions were approximated in case of small values of time and the error analyses associated with the approximation were also undertaken.The results indicate that the square root relationship of gas release in the early stage of desorption,which is widely used to provide a simple and fast estimation of the lost gas,is the first term of the approximation,and care must be taken in using the square root relationship as a significant error might be introduced with increase in the lost time and decrease in effective diameter of a cylindrical coal sample.

Determination of indices and critical values of gas parameters of the first gas outburst in a coal seam of the Xieqiao Mine

Based on the important role in mine safety played by parameters of the first gas outburst, we propose a method of combining historic data, theoretical analysis and experimental research for the purpose of crit- ical values of gas parameters of the first gas outburst in a coal seam of the Xieqiao Mine. According to a characteristic analysis and a summary of the rules of coal and gas outbursts in the No.8 coal seam of a Hua- inan mine, we have investigated their effect on coal and gas outbursts in terms such as ground stress, gas, and coal structure. We have selected gas parameters and determined the critical values of each of the fol- lowing indices： gas content as 7.7 m^3/t, tectonic coal as 0.8 m thick, the absolute gas emission as 2 m3/min, the rate of change as 0.7 m3/min, the gas desorption index of a drilling chip KI as 0.26 mL/（g min^1/2） and the values of desorption indexes Ah2 as 200 Pa. From a verification of the production, the results indicate that application of each index and their critical values significantly improve the level of safety in the pro- duction process, relieve the burden upon the mine, save much labor and bring clear economic benefits.