Optimal preparation of Bose and Fermi atomic gas mixtures of ^(87)Rb and ^(40)K in a crossed optical dipole trap

We report on the optimal production of the Bose and Fermi mixtures with ^(87) Rb and ^(40)K in a crossed optical dipole trap(ODT).We measure the atomic number and lifetime of the mixtures in combination of the spin state |F=9/2,m_(F)=9/2> of^(40)K and |1,1>of ^(87) Rb in the ODT,which is larger and longer compared with the combination of the spin state |9/2,9/2> of^(40)K and 12,2) of ^(87)Rb in the ODT.We observe the atomic numbers of ^(87)Rb and ^(40)K shown in each stage of the sympathetic cooling process while gradually reducing the depth of the optical trap.By optimizing the relative loading time of atomic mixtures in the MOT,we obtain the large atomic number of ^(40)K(~6 ×10^(6)) or the mixtures of atoms with an equal number(~1.6 × 10^(6)) at the end of evaporative cooling in the ODT.We experimentally investigate the evaporative cooling in an enlarged volume of the ODT via adding a third laser beam to the crossed ODT and found that more atoms(8 × 10^(6)) and higher degeneracy(T/T_(F)=0.25) of Fermi gases are obtained.The ultracold atomic gas mixtures pave the way to explore phenomena such as few-body collisions and the Bose-Fermi Hubbard model,as well as for creating ground-state molecules of ^(87)Rb^(40)K.

The effective ionization coefficients and electron drift velocities in gas mixtures of CF_3I with N_2 and CO_2 obtained from Boltzmann equation analysis

The electron swarm parameters including the density-normalized effective ionization coefficients（α-η）/N and the electron drift velocities V e are calculated for a gas mixture of CF3I with N2 and CO2 by solving the Boltzmann equation in the condition of a steady-state Townsend（SST） experiment.The overall density-reduced electric field strength is from 100 Td to 1000 Td（1 Td = 10-17V·cm2）,while the CF3I content k in the gas mixture can be varied over the range from 0% to 100%.From the variation of（αη）/N with the CF3I mixture ratio k,the limiting field strength（E/N） lim for each CF3I concentration is derived.It is found that for the mixtures with 70% CF3I,the values of（E/N） lim are essentially the same as that for pure SF 6.Additionally,the global warming potential（GWP） and the liquefaction temperature of the gas mixtures are also taken into account to evaluate the possibility of application in the gas insulation of power equipment.

Distribution performance of gas–liquid mixture in the shell side of spiral-wound heat exchangers

The non-uniformity of gas–liquid mixture is a critical issue which leads to the heat transfer deterioration of spiralwound heat exchangers(SWHEs).Two-phase mass flow rate and the content of gas are important parameters as well as structural parameters which have prominent influences on flow distribution uniformity of SWHE shell side.In order to investigate the influences of these parameters,an experimental test system was built using water and air as mediums and a novel distributor named"tubes distributor"was designed.The effects of mass flow rate and the content of gas on two-phase distribution performance were analyzed,where the mass flow rate ranged from 28.4 to 171.9 kg·h-1 and the content of gas changed from 0.2 to 0.8,respectively.The results showed that the mixture mass flow rate considerably influenced the liquid distribution than that of gas phase and the larger mass flow rate exhibited the better distribution uniformity of two-phase flow.It was also found that the tubes distributor had the better two-phase uniformity when the content of gas was around 0.4.Tube diameter played an important role in the distribution of gas phase and slit width was more significant for the uniformity of liquid phase.

Investigation of the performance of CF3I/c-C4F8/N2 and CF3I/c-C4F8/CO2 gas mixtures from electron transport parameters

CF3I gas mixtures have attracted considerable attention as potential environmentally-friendly alternatives to SF6 gas,owing to their excellent insulating performance.This paper attempts to study the CF3I ternary gas mixtures with c-C4F8 and buffer gases N2 and CO2 by considering dielectric strength from electron transport parameters based on the Boltzmann method and synergistic effect analysis,compared with SF6 gas mixtures.The results confirm that the critical electric field strength of CF3I/c-C4F8/70%CO2 is greater than that of 30%SF6/70%CO2 when the CF3I content is greater than 17%.Moreover,a higher content of c-C4F8 decreases the sensitivity of gas mixtures to an electric field,and this phenomenon is more obvious in CF3I/c-C4F8/CO2 gas mixtures.The synergistic effects for CF3I/c-C4F8/70%N2 were most obvious when the c-C4F8 content was approximately 20%,and for CF3I/c-C4F8/70%CO2 when the c-C4F8 content was approximately 10%.On the basis of this research,CF3I/c-C4F8/70%N2 shows better insulation performance when the c-C4F8 content is in the15%–20%range.For CF3I/c-C4F8/70%CO2,when the c-C4F8 content is in the 10%–15%range,the gas mixtures have excellent performance.Hence,these gas systems might be used as alternative gas mixtures to SF6 in high-voltage equipment.

Investigation of the hydrate formation process in fine sediments by a binary CO2/N2 gas mixture

To obtain the fundamental data of CO2/N2 gas mixture hydrate formation kinetics and CO2 separation and sequestration mechanisms,the gas hydrate formation process by a binary CO2/N2 gas mixture(50:50)in fine sediments(150–250μm)was investigated in a semibatch vessel at variable temperatures(273,275,and 277 K)and pressures(5.8–7.8 MPa).During the gas hydrate reaction process,the changes in the gaseous phase composition were determined by gas chromatography.The results indicate that the gas hydrate formation process of the binary CO2/N2 gas mixture in fine sediments can be reduced to two stages.Firstly,the dissolved gas containing a large amount of CO2 formed gas hydrates,and then gaseous N2 participated in the gas hydrate formation.In the second stage,all the dissolved gas was consumed.Thus,both gaseous CO2 and N2 diffused into sediment.The first stage in different experiments lasted for 5–15 h,and>60%of the gas was consumed in this period.The gas consumption rate was greater in the first stage than in the second stage.After the completion of gas hydrate formation,the CO2 content in the gas hydrate was more than that in the gas phase.This indicates that CO2 formed hydrate easily than N2 in the binary mixture.Higher operating pressures and lower temperatures increased the gas consumption rate of the binary gas mixture in gas hydrate formation.

Predicting the Dielectric Strength of c-C_4F_8 and SF_6 Gas Mixtures by Monte Carlo Method

An improved Monte Carlo method was used to simulate the motion of electrons in c-C4F8 and SF6 gas mixtures for pulsed townsend discharge. The electron swarm parameters such as effective ionization coefficient, -↑α and drift velocity over the E/N range from 280～700 Td（1Td=10^-21 V·m^2） were calculated by employing a set of cross sections available in literature. From the variation cure of -↑α with SF6 partial pressure p, the limiting field （E/N）lim of gas mixture at different gas content was determined. It is found that the limiting field of c-C4F8 and SF6 gas mixture is higher than that of pure SF6 at any SF6 mixture ratio. Simulation results show excellent agreement with experiment data available in previous literature.

Numerical simulation for explosion wave propagation of combustible mixture gas

A two-dimensional multi-material code was indigenously developed to investigate the effects of duct boundary conditions and ignition positions on the propagation law of explosion wave for hydrogen and methane-based combustible mixture gas. In the code,Young's technique was employed to track the interface between the explosion products and air,and combustible function model was adopted to simulate ignition process. The code was employed to study explosion flow field inside and outside the duct and to obtain peak pressures in different boundary conditions and ignition positions. Numerical results suggest that during the propagation in a duct,for point initiation,the curvature of spherical wave front gradually decreases and evolves into plane wave. Due to the multiple reflections on the duct wall,multi-peak values appear on pressure-time curve,and peak pressure strongly relies on the duct boundary conditions and ignition position. When explosive wave reaches the exit of the duct,explosion products expand outward and forms shock wave in air. Multiple rarefaction waves also occur and propagate upstream along the duct to decrease the pressure in the duct. The results are in agreement with one-dimensional isentropic gas flow theory of the explosion products,and indicate that the ignition model and multi-material interface treatment method are feasible.

Calculation and characteristic analysis on synergistic effect of CF3I gas mixtures

CF3I is a potential SF6 alternative gas.In order to study the insulation properties and synergistic effects of CF3I/N2 and CF3I/CO2 gas mixtures,two-term approximate Boltzmann equations were used to obtain the ionization coefficient α,attachment coefficient η and the critical equivalent electrical field strength（E/N）（cr）.The results show that the（E/N）（cr）of CF3I gas at 300 K is 1.2 times that of SF6 gas,and CF3I/N2 and CF3I/CO2 gas mixtures both have synergistic effect occurred.The synergistic effect coefficient of CF3I/CO2 gas mixture was higher than that of CF3I/N2 gas mixture.But the（E/N）（cr）of CF3I/N2 is higher than that of CF3I/CO2 under the same conditions.When the content of CF3I exceeds 20%,the （E/N）（cr） of CF3I/N2 and CF3I/CO2 gas mixture increase linearly with the increasing of CF3I gas content.The breakdown voltage of CF3I/N2 gas mixture is also higher than that of CF3I/CO2 gas mixture in slightly non-uniform electrical field under power frequency voltage,but the synergistic effect coefficients of the two gas mixtures are basically the same.

Deformation and water/gas flow properties of claystone/bentonite mixtures

As a potential engineered barrier material for disposal of radioactive waste in clay formations,claystone aggregate excavated from the Opalinus clay(OPA),its mixture with bentonite MX80 in a mass ratio of 7/3,and pure bentonite were extensively investigated with respect to the hydro-mechanical properties and performances.With these materials,a series of parallel experiments was performed under sequentially applied conditions of hydration with synthetic porewater of the clay formation,consolidation and water flow under increased stresses,and gas injection into the water-saturated and compacted materials under loading.Significant responses of the clay mixtures were observed.Main findings include:(1)the hydration and induced swelling of the mixtures are mainly dominated by bentonite content and dry density;(2)the consolidation decreases the porosity and water permeability exponentially by 2-3 orders of magnitude to low values of 10^(-18)-10^(-20) m^(2) at stresses of 2-5 MPa,depending upon bentonite content;and(3)the gas penetration in the water-saturated and compacted bentonite is characterised by a cyclic pressure rising/dropping process limited in between the upper breakthrough and lower shut-off boundaries,whereas the compacted claystone and claystone/bentonite mixture allow for gas release at low and moderate pressures.The results are helpful for design of the engineered barriers for safe isolation of radioactive waste in repositories.

Protective behavior of an SO_2/CO_2 gas mixture for molten AZ91D alloy

The protective behavior for a molten AZ91D alloy in an open melting furnace was investigated under a protective gas mixture containing 3% SO2 and 97% CO2, and the protection mechanism was discussed. Experimental results show that the gas mixture provides effective protection for AZ91D melt in the temperature range from 680 ℃ to 730 ℃. The microstructure, chemical composition and phase composition of the surface film formed on the molten AZ91D alloy were analyzed using scanning electron microscopy （SEM） with energy dispersive spectrometer （EDS） and X-ray diffraction （XRD）. The SEM results demonstrate that the surface films with an average thickness between 0.5 pm and 2 pm are dense and coherent in the protected temperature range. The EDS results reveal that the surface film mainly contains elements S, C, O, AI and Mg. The XRD results show that the surface film consists of MgO, MgS and a small amount of C phase.

Identification of the normal and abnormal glow discharge modes in a neon-xenon gas mixture at low pressure

In this paper, we focused on the identification of the normal and abnormal glow discharge modes in a neon-xenon gas mixture at low pressure. We considered four gas mixtures： 90%Ne-10%Xe, 80%Ne-20%Xe, 70%Ne-30%Xe and 50%Ne-50%Xe at 1.5 Torr. The range of the gap voltage is 150-500 V. A one-dimensional fluid model with multiple species was used in this work, and the metastable state of the atoms as well as the radiation effects were integrated into the model too. The input data changed for each percentage in the gas mixture, and was calculated by BOLSIG＋ software. The parameters of particle transport and their rate coefficients strictly depend on the mean electron energy. The results show that the neon ion density is negligible compared to the xenon ion density, mostly in the case of 50%Ne-50%Xe.

The Effect of Pressure on the Dissociation of H_2/CH_4Gas Mixture during Diamond Films Growth via Chemical Vapor Deposition

Monte Carlo simulations are adopted to study the electron motion in the mixture of H2 and CH4 during diamond synthesis via Glow Plasma-assisted Chemical Vapor Deposition (GPCVD). The non-uniform electric field is used and the avalanche of electrons is taken into account in this simulation. The average energy distribution of electrons and the space distribution of effective species such as CH3, CH+3, CH+ and H at various gas pressures are given in this paper, and optimum experimental conditions are inferred from these results.

Distinguished discriminatory separation of CO2 from its methane-containing gas mixture via PEBAX mixed matrix membrane

Highly selective separation of CO_2 from its methane-containing binary gas mixture can be achieved by using Poly(ether-block-amide)(PEBAX)mixed matrix membranes(MMMs).According to FESEM and AFM analyses,silica-based nanoparticles were homogenously integrated within the polymer matrix,facilitating penetration of CO_2 through the membrane while acting as barrier for methane gas.The membrane containing 4.6 wt% fumed silica(FS)(PEBAX/4.6 wt%FS)exhibits astonishing selectivity results where binary gas mixture of CO_2/CH_4 was used as feed gas.As detected by gas chromatography,in the permeate side,data showed a significant increase of CO_2 permeance,while CH_4 transport through the mixed matrix membrane was not detectable.Moreover,PEBAX/4.6 wt%FS greatly exceeds the Robeson limit.According to data reported on CO_2/CH_4 gas pair separation in the literature,the results achieved in this work are beyond those data reported in the literature,particularly when PEBAX/4.6 wt%FS membrane was utilized.

Prediction of Volumetric Properties(p-v-T)of Natural Gas Mixtures Using Extended Tao-Mason Equation of State

A statistical-mechanical-based equation of state(EOS)for pure substances,the Tao-Mason equation of state,is successfully extended to prediction of the(p-v-T)properties of fourteen natural gas mixtures at temperatures from 225 K to 483 K and pressures up to 60.5 MPa.This work shows that the Tao-Mason equation of state for multicomponent natural gas is predictable with minimal input information,namely critical temperature,critical pressure,and the Pitzer acentric factor.The calculated results agree well with the experimental data.From a total of 963 data of density and 330 data of compressibility factor for natural gases examined in this work,the average absolute deviations(AAD)are 1.704%and 1.344%,respectively.The present EOS is further assessed through the comparisons with Peng-Robinson(PR)equation of state.For the all of mixtures Tao-Mason(TM)EOS outperforms the PR EOS.

Dispersion Relations in Binary Gas Mixtures From a Kinetic Theory

Sound propagation and the initial value problems in gas mixtures of two components are investigated. By using the eigen theory of linearized Boltzmann equations, a model equations is formed, with the use of the Fourier-Laplace transform for model equations derived, the dispersion relations for both components are obtained.

Influence of the Gas Mixture Ratio on the Correlations Between the Excimer XeCl Emission and the Sealed Gas Temperature in Dielectric Barrier Discharge Lamps

For dielectric barrier discharge lamps filled with various gas mixture ratios, the correlations between the excimer XeCl* emission and the sealed gas temperature have been founded, and a qualitative explication is presented. For gas mixture with chlorine larger than 3%, the emission intensity increases with the sealed gas temperature, while with chlorine about 2%, the emission intensity decreases with the increase in the gas temperature, and could be improved by cooling water. However, if chlorine is less than 1.5%, the discharge appears to be a mixture mode with filaments distributed in a diffused glow-like discharge, and the UV emission is independent on the gas temperature.

Sulfur production from smelter off-gas using CO–H2 gas mixture as the reducing agent over modified Fe/γ-Al2O3 catalysts

A series of modifiedγ-Al_2O_3supported iron-based catalysts(M-Fe/γ-Al_2O_3)was developed to reduce SO_2in actual smelter off-gases using CO–H_2gas mixture as reducing agent for sulfur production.Used as modifiers,three metal additives—Ni,Co,and Ce were added to Fe/γ-Al_2O_3catalysts.Changes in catalyst structure and active phase were characterized with X-ray diffraction,XPS,SEM,and EDS.The reduction ability of catalysts was exhibited via CO-TPR.The prepared catalysts only need to be pre-reacted for a period of time,eliminating the need for presulfidation treatment.Reaction conditions were optimized in a fixed bed reactor to achieve high SO_2conversion and sulfur selectivity.XRD characterization was carried out to verify the resulting sulfur products.Combining in situ infrared characterization and catalyst evaluation of support and active component,the reaction mechanism was investigated and proposed.

Applying Improved Electrical Breakdown Model to Study Insulating Property of c-C_4F_8/N_2 Gas Mixture

Perfluorocyclobutane(c-C4F8) has been recently considered as a potential alternative to SF6,because of its high electro-negativity and extremely low environmental effect.However,due to its high boiling point,c-C4F8 should mixed with buffer gases such as N2 or CO2 in order to avoid the liquefaction at low temperature.This paper investigates insulating properties of c-C4F8/N2 gas mixtures from two aspects including electrical strength,and Global Warming Potential(GWP).Moreover,improved electrical breakdown model of gas mixtures is founded.Breakdown temperature and breakdown electrical field in gas mixtures can be obtained from rigorous Townsend criterion expression according to gas mixtures ratio and cross section data of gas mixtures in this model.Under the condition of different gas pressure(0.1~0.4 MPa),gas mixtures ratio(0～30%),and electrode gap(2~10 mm),breakdown voltages of gas mixtures are calculated by using of this model.Insulation strength of SF6/N2 mixed gas is compared with c-C4F8/N2 mixed gas in the same conditions.Research results show that theoretical computation corresponds with experiment.If the content of c-C4F8 or SF6 in mixtures is less than 30%,insulation strength between c-C4F8/N2 and SF6/N2 is very close.Considering two indexes(breakdown voltage,GWP),it is suitable for c-C4F8 content being 15%～20% in c-C4F8/N2 gas

Evaluation of the Effectiveness of a 4-Months Continuous Injection of a Gas Mixture (CO₂and Inert Gases) on <i>Legionella</i>Contamination of a Hot Water Distribution System

Within the biofilm and scales Legionella is less far susceptible to the effects of the most frequently used biocides. The objective of this study was to evaluate the effect of a 4-months continuous injection of a gas mixture (CO2 and inert gas) in the hot water distribution system of a large hotel colonized by L. pneumophila sg3 on limiting biofilm formation and scales and in turn Legionella growth. Before the continuous injection of the gas mixture, out of the 15 sampling points examined every month 60% were colonized by Legionella (mean concentrations of 102 cfu/L in the boilers and the return loop, and 104 cfu/L in taps and showers). One week after the injection of the gas mixture and daily fluxing of the distal outlets, the level of colonization decreased (3 cfu/L). When it was decided to flux all the distal outlets only 1 day per week the mean concentration of Legionella increased again (>104 cfu/L) in all the sampling points. Thus, cleaning of the boilers was performed and distal outlets were again fluxed daily. One week after the level of contamination decreased again (2 cfu/L). Nonetheless, the colonization was not eliminated and when fluxing of the distal outlets was not performed every day the mean concentrations of Legionella raised up to >104 cfu/L. Results indicate that the gas mixture was able to reduce the level of colonization by Legionella only because associated to the fluxing of the distal outlets.

Experimental study on explosion limit of M15 methanol-gasoline mixture

The explosion characteristics of M15 methanol-gasoline mixture was experimental test by using FRTA explosion limit instrument.The effect of temperature on the explosion area of the sample was studied.The results show that the lower explosion limit of M15 methanol-gasoline mixture is 1.716%and the upper explosion limit is 11.451%at the initial temperature of 80℃.The lower explosion limit of M15 methanol-gasoline is in the range of 1.711%-1.760%with the initial temperature from 25℃to 100℃,and the upper explosion limit of the sample changes between 11.253%and 11.451%.Considering experimental error and precision,it can be approximated that the temperature has little influence on the explosion area of M15 methanol-gasoline mixture.