Research on the sensitivity for the coal mine gas concentration detection by laser spectrum absorption

Because of the former gas chemistry examination method defects, tunable diode laser absorption spectrum technology （TDLAS） was used. It used an isolated absorption spectrum of the gas molecule to measure the gas absorption spectrum in order to distinguish the gas conveniently. The second harmonic （20 was measured in this system. Due to the fact which the harmonious signal is proportional to the concentration of the absorption gas, the gas concentration may be obtained through examining harmonious signal. The theoretical analysis and the experimental result indicate that under the same level of pressure, survey with the signal-to-noise ratio（SNR） of 2fsignal increases the accuracy by one order of magnitude and may reach 10 ^-3 and the sensitivity may reach the 10^-6 level compared to that of direct absorption. 5% methane density and a 30 cm absorption cell were used in the experiment. It has several advantages including high sensitivity, best resolution, and faster response and so on. The gas concentration monitoring of coal mine may be accomplished.

Influence of the Gas Mixture Ratio on the Correlations Between the Excimer XeCl Emission and the Sealed Gas Temperature in Dielectric Barrier Discharge Lamps

For dielectric barrier discharge lamps filled with various gas mixture ratios, the correlations between the excimer XeCl* emission and the sealed gas temperature have been founded, and a qualitative explication is presented. For gas mixture with chlorine larger than 3%, the emission intensity increases with the sealed gas temperature, while with chlorine about 2%, the emission intensity decreases with the increase in the gas temperature, and could be improved by cooling water. However, if chlorine is less than 1.5%, the discharge appears to be a mixture mode with filaments distributed in a diffused glow-like discharge, and the UV emission is independent on the gas temperature.

A New Method for the Dynamic Reserves of Gas Condensate Reservoir Using Cyclic Gas Injection Based on the Effects of Reinjection Ratio and Water Influx

As we all know, cyclic gas injection is one of the most effective development methods to improve condensate oil recovery. When dealing with the calculation of the reserves, the injection-production differences and water influx create great influence on the accuracy. Based on the existing research, we proposed a new material balance equation which considered the differences of composition between produced and injected fluids and the effect of water influx, and a solution was provided in this paper. The results of the method are closer to the actual situation because they are built on the law of conservation of mass, and the using of curve fitting method can not only avoid the use of water influx coefficient but also obtain the water influx rate and reserves at the same time. The YH-23 gas condensate reservoir is taking as a typical subject to do the research, which has been exploited by cycle gas injection for 14 years. Three different methods are used to calculate the reserves, and the results show that the method proposed in this paper has minimum error of 2.96%.

The R&D of a Novel Sulfur Tolerant CO Shift Catalyst and Its Application in the Integrated Low Water Gas Ratio Process

The QDB-5 sulfur tolerant CO shift catalyst, with anti-methanation property by supported compositing alkali promoters, has been proved to effectively reduce the outlet methane content in the condition of a low water gas ratio. Thus, a new technology based on a lower water/gas ratio than before has been developed with the new catalyst. The CO conversion at lower temperatures and catalyst stability were confirmed by long term industrial application. The high temperature catalyst performance also showed a better result than the conventional commercial catalyst, with higher CO conversion and well controlled methane outlet. Our research and the industrial application of catalyst have shown the importance of alkali metals as core promoters for such kind of catalysts.

Net Energy Ratio and Greenhouse Gas Analysis of a Biogas Power Plant

The results of a net energy life cycle analysis and greenhouse gas analysis for a 1.45 MW （0.71 MW electrical） biogas power plant operating with a 70% corn silage and 30% cow dung feedstock mixture are presented after its initial five years of operation. A ratio of 8.0 for the total output electrical energy divided by the total input energy from fossil fuels is found. A net efficiency of 1.2% of converting solar energy into electricity and usable heat （0.6% electricity） is achieved. Only 16 g CO2 per kWh are generated in the process. If all greenhouse gases are considered, this process even actively reduces the total greenhouse gas load on the atmosphere. In terms of producing transportation biofuels, this process provides 3.8 times more yield per hectare than bioethanol generation.

Economic feasibility and efficiency enhancement approaches for in situ upgrading of low-maturity organic-rich shale from an energy consumption ratio perspective

The technical feasibility of in situ upgrading technology to develop the enormous oil and gas resource potential in low-maturity shale is widely acknowledged.However,because of the large quantities of energy required to heat shale,its economic feasibility is still a matter of debate and has yet to be convincingly demonstrated quantitatively.Based on the energy conservation law,the energy acquisition of oil and gas generation and the energy consumption of organic matter cracking,shale heat-absorption,and surrounding rock heat dissipation during in situ heating were evaluated in this study.The energy consumption ratios for different conditions were determined,and the factors that influence them were analyzed.The results show that the energy consumption ratio increases rapidly with increasing total organic carbon(TOC)content.For oil-prone shales,the TOC content corresponding to an energy consumption ratio of 3 is approximately 4.2%.This indicates that shale with a high TOC content can be expected to reduce the project cost through large-scale operation,making the energy consumption ratio after consideration of the project cost greater than 1.In situ heating and upgrading technology can achieve economic benefits.The main methods for improving the economic feasibility by analyzing factors that influence the energy consumption ratio include the following:(1)exploring technologies that efficiently heat shale but reduce the heat dissipation of surrounding rocks,(2)exploring technologies for efficient transformation of organic matter into oil and gas,i.e.,exploring technologies with catalytic effects,or the capability to reduce in situ heating time,and(3)establishing a horizontal well deployment technology that comprehensively considers the energy consumption ratio,time cost,and engineering cost.

Acquisition Practice of High Signal-to-Noise Ratio in YTB Block of Sichuan Basin

YTB block in Sichuan basin is a favorable area to exploit oil and gas in shallow tight rock. 3D seismic project of this zone has two characteristics. Firstly, it has high requirements for the tolerance rate of the construction process and the acquisition of high signal-to-noise ratio seismic data;Second, there are widely obstacles and noises that lead to difficult acquisition construction organization. In acquisition practice, high signal-to-noise ratio seismic data was obtained by reasonable design of construction scheme, optimization of excitation parameters, improvement of receiving conditions and optimization of obstacle crossing observation system. .

Design of a Silicon Beam Resonator for a Novel Gas Sensor

A new silicon beam resonator design for a novel gas sensor based on simultaneous conductivity and mass change measurement is investigated. High selectivity and sensitivity in gas detection can be obtained by measuring the charge-to-mass ratio of gas molecules. Structures of silicon beam resonators are designed, simulated, and optimized. This gas sensor is fabricated using sacrificial layer microelectronmechanical system technology, and the resonant frequency of the microbeam is measured.

Bohai crude oil identification by gas chromatogram fingerprinting quantitative analysis coupled with cluster analysis

By gas chromatogram, six crude oils fingerprinting distributed in four oilfields and four oil platforms were analyzed and the corre- sponding normal paraffin hydrocarbon （ including pristane and phytane） concentration was obtained by the internal standard methed. The normal paraffin hydrocarbon distribution patterns of six crude oils were built and compared. The cluster analysis on the normal paraffin hydrocarbon concentration was conducted for classification and some ratios of oils were used for oils comparison. The results indicated： there was a clear difference within different crude oils in different oil fields and a small difference between the crude oils in the same oil platform. The normal paraffin hydrocarbon distribution pattern and ratios, as well as the cluster analysis on the nomad paraffin hydrocarbon concentration can have a better differentiation result for the crude oils with small difference than the original gas chromatogram.

Energy-limiting factor for coal and gas outburst occurrence in intact coal seam

This research reviewed the mechanics and gas desorption properties of intact coal,and tested the crushing work ratios of different intact coals,and then,studied the stress conditions for the failure or crushing of intact coal and the gas demand for the pulverization of intact coal particles.When a real-life outburst case is examined,the required minimum stress for intact coal outburst is estimated.The study concludes that the crushing work ratios of three intact coal samples vary from 294.3732 to 945.8048 J/m^(2).For the real-life case,more than 2300 MJ of transport work is needed,and 10062.09,7046.57 and 5895.47 m^(3) of gas is required when the gas pressure is 1,2 and 3 MPa,respectively.The crushing work exceeds the transport work and even reaches 13.96 times of the transport work.How to provide such an enormous crushing work is an energy-limiting factor for the outburst in intact coal.The strain energy is needed for the crushing work,and the required minimum stress is over 54.35 MPa,even reaching 300.44 MPa.These minimum stresses far exceed the in-situ vertical and horizontal stresses that can be provided at the 300–700 m mining depth range.

A LATTICE BOLTZMANN MODEL FOR COMPRESSIBLE PERFECT GAS

A new lattice Boltzmann model for compressible perfect gas is proposed. The numerical example shows that it can be used to simulate shock wave and contact discontinuity. The results are comparable with those obtained by traditional methods. The ratio of specific heats gamma may be chosen according to the requirement of problems.

Exploring heating performance of gas engine heat pump with heat recovery

In order to evaluate the heating performance of gas engine heat pump（GEHP） for air-conditioning and hot water supply, a test facility was developed and experiments were performed over a wide range of engine speed（1400-2600 r/min）, ambient air temperature（2.4-17.8 ℃） and condenser water inlet temperature（30-50℃）. The results show that as engine speed increases from 1400 r/min to 2600 r/min, the total heating capacity and energy consumption increase by about 30% and 89%, respectively; while the heat pump coefficient of performance（COP） and system primary energy ratio（PER） decrease by 44% and 31%, respectively. With the increase of ambient air temperature from 2.4 ℃ to 17.8 ℃, the heat pump COP and system PER increase by 32% and 19%, respectively. Moreover, the heat pump COP and system PER decrease by 27% and 15%, respectively, when the condenser water inlet temperature changes from 30 ℃ to 50 ℃. So, it is obvious that the effect of engine speed on the performance is more significant than the effects of ambient air temperature and condenser water inlet temperature.

Development and testing of a detailed kinetic mechanism of natural gas combustion in internal combustion engine

A detailed chemical mechanism to describe the combustion of natural gas in internal combustion （IC） engine has been developed,which is consisting of 233 reversible reactions and 79 species.This mechanism accounts for the oxidation of methane,ethane,propane and nitrogen.It has been tested using IC engine model of CHEMKIN 4.1.1 and experimental measurements.The performance of the proposed mechanism was evaluated at various equivalence ratios （φ=0.6 to φ=1.3）,initial reactor conditions （Tini=500 to 3500 ℃; Pini=1.0 to 10 atm） and engine speed （2000-7000 rpm）.The proposed kinetic mechanism shows good concordances with GRI3.0 mechanism especially in the prediction of temperature,pressure and major product species （H2O,CO2） profiles at stoichiometric conditions （φ=1.0）.The experimental results of measured cylinder pressure,species fractions were also in agreement with simulation results derived from the proposed kinetic mechanism.The proposed mechanism successfully predicts the formation of gaseous pollutants （CO,NO,NO2,NH3） in the engine exhaust.Although there are some discrepancies among each simulation profile,the proposed detailed mechanism is good to represent the combustion of natural gas in IC engine.

Propagation velocity measurement for flame of gas explosion in horizontal tube

In coal industry,gas explosion accidents emerge constantly,causing enormous casualties and poorer material property.In the course of studying gas exploding mechanism,the propagation velocity of the flame wave front is one of the most important factors.A set of flame velocity measuring system was designed according to the horizontal pipelined experimental facility of North University of China to study the effects of the quantity and blockage ratio of the circle ring obstacle on the flame propagation velocity in the inclosed tube.The research results show that the obstacle has obviously accelerating effect on the flame wave of gas explosion With the increase of quantity and blockage ratio of the obstacle,the flame accelerating effect becomes more obvious and the flame accelerating persistence is intenser,of which the effect of the quantity of the obstacle on the flame accelerating persistence is larger,but the effect of the blockage ratio of the obstacle on the flame accelerating persistenceis not obvious.

Analysis of the dialectical relation between top coal caving and coal-gas outbtu rst

According to the different engineering mechanical states of top coal caving andnormal stoping of gaseous loose thick coal seams,the dialectical relation between thiscaving method and dynamic disasters was analyzed by simulating the change of stressstates in the process of top coal initial caving with different mining and caving ratios basedon the ANSYS10.0.The variation of elastic energy and methane expansion energy duringfirst top coal caving was analyzed by first weighting and periodic weighting and combiningwith coal stress and deformation distribution of top coal normal stoping as well as positiveand negative examples in top coal caving of outburst coal seam.The research shows thatthe outburst risk increases along with the increase of the caving ratio in the initial miningstage.In the period of normal stoping,when the mining and caving ratio is smaller than1:3 and hard and massive overlying strata do not exist (periodic weighting is not obvious),it is beneficial to control ground stress leading type outburst.Thus,it is unreasonable toprohibit top coal caving in dangerous and outburst prone areas.

Influence of Reaction Conditions on Methanol Synthesis and WGS Reaction in the Syngas-to-DME Process

A series of CuO-ZnO catalysts （with different Cu/Zn molar ratios） were prepared, and evaluated under the reaction conditions of syngas-to-dimethyl ether （DME） with three sorts of feed gas and different space velocity. The catalysts were characterized by X-ray diffraction （XRD） and temperatureprogrammed reduction （TPR）. The experiment results showed that the reaction conditions of syngas-to- DME process greatly affected the methanol synthesis and WGS reaction. The influence caused by Cu/Zn molar ratio was quite different on the two reactions; increasing of percentage of CO2 in feed gas was unfavorable for catalyst activity, and also inhibited both reactions; enhancement of reaction space velocity heavily influenced the performance of the catalyst, and the benefits were relatively less for methanol synthesis than for the WGS reaction.

Simulation Research on the Effect of Cooled EGR, Supercharging and Compression Ratio on Downsized SI Engine Knock

Knock in spark-ignition（SI） engines severely limits engine performance and thermal efficiency. The researches on knock of downsized SI engine have mainly focused on structural design, performance optimization and advanced combustion modes, however there is little for simulation study on the effect of cooled exhaust gas recirculation（EGR） combined with downsizing technologies on SI engine performance. On the basis of mean pressure and oscillating pressure during combustion process, the effect of different levels of cooled EGR ratio, supercharging and compression ratio on engine dynamic and knock characteristic is researched with three- dimensional KIVA-3V program coupled with pressure wave equation. The cylinder pressure, combustion temperature, ignition delay timing, combustion duration, maximum mean pressure, and maximum oscillating pressure at different initial conditions are discussed and analyzed to investigate potential approaches to inhibiting engine knock while improving power output. The calculation results of the effect of just cooled EGR on knock characteristic show that appropriate levels of cooled EGR ratio can effectively suppress cylinder high-frequency pressure oscillations without obvious decrease in mean pressure. Analysis of the synergistic effect of cooled EGR, supercharging and compression ratio on knock characteristic indicates that under the condition of high supercharging and compression ratio, several times more cooled EGR ratio than that under the original condition is necessarily utilized to suppress knock occurrence effectively. The proposed method of synergistic effect of cooled EGR and downsizing technologies on knock characteristic, analyzed from the aspects of mean pressure and oscillating pressure, is an effective way to study downsized SI engine knock and provides knock inhibition approaches in practical engineering.

Growing Cover Crops to Improve Biomass Accumulation and Carbon Sequestration: A Phytotron Study

Cover crop system has shown a potential approach to improving carbon sequestration and environmental quality. Six of each winter and summer cover crops were subsequently grown in two soils, Krome gravelly loam soil (KGL), and Quincy fine sandy soil (QFS), in phytotrons at 3 temperatures (10/20, 15/25, 25/30oC for winter/summer cover crops) to investigate their contributions for carbon (C) sequestration. Among winter cover crops, the highest and the lowest amounts of C accumulated were by bellbean (Vicia faba L.), 597 g/m2 and white clover (Trifolium repens), 149 g/m2, respectively, in the QFS soil. Among summer cover crops, sunn hemp (Crotalaria juncea L.) accumulated the largest quantity of C (481 g/m2), while that by castorbean (Ricinus communis) was 102 g/m2 at 30oC in the KGL soil. The mean net C remained in the residues following the 127 d decomposition were 187 g/m2 of C (73% of the total) and 91 g/m2 (52% of the total) for the winter and summer cover crops, respectively. Following a whole cycle of winter and summer cover crops grown, the mean soil organic C (SOC) increased by 13.8 and 39.1% in the KGL and QFS soil, respectively, compared to the respective soils before. The results suggest that triticale, ryegrass, and bellbean are the promising winter cover crops in the QFS soil, while sunn hemp, velvetbean (Mucuna pruriens), and sorghum sudangrass (Sorghum bicolor ×S. bicolor) are recommended summer cover crops for both soils under favorable temperatures.

Riemann problem for one-dimensional binary gas enhanced coalbed methane process

With an extended Langmuir isotherm, a Riemann problem for one-dimensional binary gas enhanced coalbed methane (ECBM) process is investigated. A new analytical solution to the Riemann problem, based on the method of characteristics, is developed by introducing a gas selectivity ratio representing the gas relative sorption affinity. The influence of gas selectivity ratio on the enhanced coalbed methane processes is identified.

Applying Improved Electrical Breakdown Model to Study Insulating Property of c-C_4F_8/N_2 Gas Mixture

Perfluorocyclobutane(c-C4F8) has been recently considered as a potential alternative to SF6,because of its high electro-negativity and extremely low environmental effect.However,due to its high boiling point,c-C4F8 should mixed with buffer gases such as N2 or CO2 in order to avoid the liquefaction at low temperature.This paper investigates insulating properties of c-C4F8/N2 gas mixtures from two aspects including electrical strength,and Global Warming Potential(GWP).Moreover,improved electrical breakdown model of gas mixtures is founded.Breakdown temperature and breakdown electrical field in gas mixtures can be obtained from rigorous Townsend criterion expression according to gas mixtures ratio and cross section data of gas mixtures in this model.Under the condition of different gas pressure(0.1~0.4 MPa),gas mixtures ratio(0～30%),and electrode gap(2~10 mm),breakdown voltages of gas mixtures are calculated by using of this model.Insulation strength of SF6/N2 mixed gas is compared with c-C4F8/N2 mixed gas in the same conditions.Research results show that theoretical computation corresponds with experiment.If the content of c-C4F8 or SF6 in mixtures is less than 30%,insulation strength between c-C4F8/N2 and SF6/N2 is very close.Considering two indexes(breakdown voltage,GWP),it is suitable for c-C4F8 content being 15%～20% in c-C4F8/N2 gas