Design of the Pumping Stations and the Gas Puffing Systems for the Superconducting Tokamak HT-7U

The design of the pumping stations and the gas injection systems for the inner Chamber and the cryostat on HT-7U superconducting tokamak is described in this paper.

Experimental Study on the Velocity and Efficiency Characteristics of a Serial Staged Needle Array-Mesh Type EHD Gas Pump

The ionic wind has good application prospects in the fields of air flow control and heat transfer enhancement. The key for successful applications is how to improve the velocity and how to increase the active area of the ionic wind. This paper designed a needle array-mesh type electrohydrodynamic （EHD） gas pump. The use of needle array electrode where corona discharge started simultaneously could enlarge the active area. The velocity of the ionic wind could increase by placing several single-stage ionic wind generators in series appropriately, called as serial staged generator. The maximum average flow velocity of 16.1 m/s and volumetric flow of 303.5 L/min were achieved at the outlet of a 25-stage gas pump and the conversion efficiency was approximately 2.2%.

Exploring heating performance of gas engine heat pump with heat recovery

In order to evaluate the heating performance of gas engine heat pump（GEHP） for air-conditioning and hot water supply, a test facility was developed and experiments were performed over a wide range of engine speed（1400-2600 r/min）, ambient air temperature（2.4-17.8 ℃） and condenser water inlet temperature（30-50℃）. The results show that as engine speed increases from 1400 r/min to 2600 r/min, the total heating capacity and energy consumption increase by about 30% and 89%, respectively; while the heat pump coefficient of performance（COP） and system primary energy ratio（PER） decrease by 44% and 31%, respectively. With the increase of ambient air temperature from 2.4 ℃ to 17.8 ℃, the heat pump COP and system PER increase by 32% and 19%, respectively. Moreover, the heat pump COP and system PER decrease by 27% and 15%, respectively, when the condenser water inlet temperature changes from 30 ℃ to 50 ℃. So, it is obvious that the effect of engine speed on the performance is more significant than the effects of ambient air temperature and condenser water inlet temperature.

The design and calculation of the delayed neutron detection system for PWR and CEFR

This paper discussed the importance of the delayed neutron detection system.We improved the delayed neutron detection station and delayed neutron detector,so the noise was greatly decreased and the detection efficiency was greatly increased.After the improvement the stability of the detector was enhanced and the false alarm was eliminated.We introduced the principle of the gas lift pump designed for the sodium cooled fast reactor.A calculation model of the failed fuel detection system of CEFR was proposed,and from the model a code using LabWindows/CVI was developed.The minimum broken area that could be detected by the delayed neutron detection system of CEFR was calculated and the delayed neutron detection signal in a few representative transient conditions during fuel failure happened was stimulated.

Lean and interpretable digital twins for building energy monitoring - A case study with smart thermostatic radiator valves and gas absorption heat pumps

The transition to low carbon energy systems poses challenges in terms of energy efficiency.In building refur-bishment projects,efficient technologies such as smart controls and heat pumps are increasingly being used as a substitute for conventional technologies with the aim of reducing carbon emissions and determining operational energy and cost savings,together with other benefits.Measured building performance,however,often reveals a significant gap between the predicted energy use(design stage)and actual energy use(operation stage).For this reason,lean and interpretable digital twins are needed for building energy monitoring aimed at persistence of savings and continuous performance improvement.In this research,interpretable regression models are built with data at multiple temporal resolutions(monthly,daily and hourly)and seamlessly integrated with the goal of verifying the performance improvements due to Smart thermostatic radiator valves(TRVs)and gas absorption heat pumps(GAHPs)as well as giving insights on the performance of the building as a whole.Further,as part of modelling research,time of week and temperature(TOWT)approach is reformulated and benchmarked against its original implementation.The case study chosen is Hale Court sheltered housing,located in the city of Portsmouth(UK).This building has been used for the field-testing of innovative technologies such as TRVs and GAHPs within the EU Horizon 2020 project THERMOSS.The results obtained are used to illustrate possible extensions of the use of energy signature modelling,highlighting implications for energy management and innovative building technologies development.

Large area perovskite solar cell module

The recent dramatic rise in power conversion efficiencies（PCE）of perovskite solar cells has triggered intense research worldwide.However,their practical development is hampered by poor stability and low PCE values with large areas devices.Here,we developed a gas-pumping method to avoid pinholes and eliminate local structural defects over large areas of perovskite film,even for 5 × 5 cm^2 modules,the PCE reached 10.6%and no significant degradation was found after 140 days of outdoor testing.Our approach enables the realization of high performance large-area PSCs for practical application.