Reliability improvement of gas discharge tube by suppressing the formation of short-circuit pathways

After cumulative discharge of gas discharge tube(GDT),it is easy to form a short circuit pathway between the two electrodes,which increases the failure risk and causes severe influences on the protected object.To reduce the failure risk of GDT and improve cumulative discharge times before failure,this work aims to suppress the formation of two short-circuit pathways by optimizing the tube wall structure,the electrode materials and the electrode structure.A total of five improved GDT samples are designed by focusing on the insulation resistance change that occurs after the improvement;then,by combining these designs with the microscopic morphology changes inside the cavity and the differences in deposition composition,the reasons for the differences in the GDT failure risk are also analyzed.The experimental results show that compared with GDT of traditional structure and material,the method of adding grooves at both ends of the tube wall can effectively block the deposition pathway of the tube wall,and the cumulative discharge time before device failure is increased by 149%.On this basis,when the iron-nickel electrode is replaced with a tungsten-copper electrode,the difference in the electrode’s surface splash characteristics further extends the discharge time before failure by 183%.In addition,when compared with the traditional electrode structure,the method of adding an annular structure at the electrode edge to block the splashing pathway for the particles on the electrode surface shows no positive effect,and the cumulative discharge time before the failure of the two structures is reduced by 22.8%and 49.7%,respectively.Among these improved structures,the samples with grooves at both ends of the tube wall and tungsten-copper as their electrode material have the lowest failure risk.

VISUAL OBSERBATION OF HCFC141b GAS HYDRATE FORMATION/DECOMPOSITION PROCESS OUTSIDE OF A TUBE

In order to design a kind of heat exchanger suitable to the indirect-touched gas hydrate cool storage vessel, a visual observation of HCFC141b gas hydrate formation/decomposition process was presented through a self-designed small-scale visualization apparatus of gas hydrate cool storage. Based on the shooted photos and recorded temperatures, the formation/decomposition process of HCFC141b are described, some characteristics are concluded, and some suggestions of designing heat exchanger are indicated according to the specific characteristics of HCFC141b gas hydrate formation/decomposition process.

Numerical and experimental study on the refrigeration performance of a variable-section gas wave oscillation tube

This paper introduces the refrigeration cycle process of the gas wave oscillation tube(GWOT).Aiming at the problem that the strong reverse compression waves generated during the refrigeration process affect the performance,this paper proposes a variable-section GWOT that weakens the reverse compression waves and a variable-section structure designed using a numerical method.Results showed that the variable-section structure could reduce the intensity of the incident shock wave by approximately 7%and the total entropy production in the refrigeration cycle by approximately 8%under the design condition.Moreover,the variable-section structure can effectively weaken the strength of the reverse compression waves and improve the refrigeration efficiency by approximately 4%under the same working conditions.The variable-section structure can also widen the highperformance working range of the GWOT.The experimental results reveal that the high-performance working range can be expanded by more than two times under the design condition.The research can guide the subsequent development of gas wave refrigeration technology and a reference for other wave rotor application technologies.

Comparison of thermal neutron detection ef f iciency of 6Li scintillation glass and 3He gas proportional tube

We report on a comparison study of the 3He gas proportional tube and the 6Li incorporated scintillation glasses on thermal neutron detection efficiency. Both 3He and 6Li are used commonly for thermal neutron detection because of their high neutron capture absorption coefficient. By using a neutron source 252Cf and a paraffin moderator in an alignment system, we can get a small beam of thermal neutrons. A flash ADC is used to measure the thermal neutron spectrum of each detector, and the detected number of events is determined from the spectrum, then we can calculate the detection efficiency of different detectors. Meanwhile, the experiment has been modeled with GEANT4 to validate the results against the Monte Carlo simulation.

Round-trip oscillation triboelectric nanogenerator with high output response and low wear to harvest random wind energy

Triboelectric nanogenerator(TENG)has made significant progress in wind energy harvesting.As the most advantageous rotary TENG among wind energy harvesters,the severe material wear and the output that fluctuates with wind speed seriously hinder the application of TENG wind energy harvesters.In this study,we propose a round-trip oscillation triboelectric nanogenerator(RTO-TENG)consisting of a crank transmission mechanism and a power generation unit.The RTO-TENG utilizes a simple crank transmission mechanism combined with a zigzag-laminated triboelectric nanogenerator(Z-TENG)to achieve high-performance constant output and low material wear.The crank transmission mechanism can realize the transformation from circular motion to arc reciprocating motion,converting the random wind energy into bi-directional kinetic energy,driving the vertical contact and separation of the Z-TENG.Due to the low transmission ratio(1:1)of the crank transmission mechanism and the consistent frequency of the Z-TENG contact–separation with that of the pendulum,the RTO-TENG’s power generation unit(10 Z-TENGs)is insensitive to changes in wind speed,resulting in a constant and stable output response at various speeds.After 480,000 cycles,the output of RTO-TENG decreased by only 0.9%compared to the initial value of 6μC,and the scanning electron microscopy(SEM)images of the polytetrafluoroethylene(PTFE)film showed no significant wear on the surface of the friction layer,demonstrating excellent output stability and abrasion resistance of the RTO-TENG wind energy collector’s material.The equipped energy management module,based on a gas discharge tube switch,can further enhance the output performance of the RTO-TENG.After optimizing its inductor parameter L to match the load capacitor,it can charge a 220μF load capacitor to 13.4 V in 40 s,resulting in a 298%improvement in charging speed compared to the voltage of 4.48 V without the management module.Therefore,the RTO-TENG can efficiently provide power to low-power small electronic devices for Internet of Things(IoTs),such as road traffic warning signs and thermo-hygrometers.