Development of a 100 MPa water–gas two-phase fluid pressurization device

This paper introduces a 100 MPa water gas twophase fluid pressurization device.The device can provide 100 MPa gas pressure and 200 MPa liquid pressure for small volume(<20 mL)high-pressure experimental devices.This device can make the pressure control independent of the temperature control without changing the material components of the system.The resolution of this device in adjusting the pressure is±0.2 MPa in the process of boosting and depressurizing.This pressure boosting device generates very little vibration during work and it can be used in experiments with strict requirements on vibration.As a thermodynamic parameter,pressure has a great influence on matter.In the field of experimental geochemistry,pressure is not only an experimental method and an extreme condition but an important physical parameter independent of temperature and chemical composition.

SIMULATION OF GAS AND LIQUID TWO-PHASE FLOW THROUGH THE BLAST FURNACE DROPPING ZONE

A three-dimensional mathematical model,based on differential balances of mass and momentum,hasbeen developed to describe the two-phase flow of gas and liquid through the dropping zone of the blast fur-nace.Agreement between observed and calculated values verifies the validity of this model.On the basis of this model,various parameters for the surrounding of the dry zone of Blast FurnaceNo.I-BF of the Beijing Iron and Steel Company have been computed,from which a diagram for demar-cation of fluidization of coke and flooding of slag has been proposed.

Simultaneous measurement of velocity profile and liquid film thickness in horizontal gas–liquid slug flow by using ultrasonic Doppler method

Horizontal gas-liquid two-phase flows widely exist in chemical engineering,oil/gas production and other important industrial processes.Slug flow pattern is the main form of horizontal gas-liquid flows and characterized by intermittent motion of film region and slug region.This work aims to develop the ultrasonic Doppler method to realize the simultaneous measurement of the velocity profile and liquid film thickness of slug flow.A single-frequency single-channel transducer is adopted in the design of the field-programmable gate array based ultrasonic Doppler system.A multiple echo repetition technology is used to improve the temporal-spatial resolution for the velocity profile.An experiment of horizontal gas-liquid two-phase flow is implemented in an acrylic pipe with an inner diameter of 20 mm.Considering the aerated characteristics of the liquid slug,slug flow is divided into low-aerated slug flow,high-aerated slug flow and pseudo slug flow.The temporal-spatial velocity distributions of the three kinds of slug flows are reconstructed by using the ultrasonic velocity profile measurement.The evolution characteristics of the average velocity profile in slug flows are investigated.A novel method is proposed to derive the liquid film thickness based on the instantaneous velocity profile.The liquid film thickness can be effectively measured by detecting the position and the size of the bubbles nearly below the elongated gas bubble.Compared with the time of flight method,the film thickness measured by the Doppler system shows a higher accuracy as a bubble layer occurs in the film region.The effect of the gas distribution on the film thickness is uncovered in three kinds of slug flows.

Prediction of Flowing Bottomhole Pressures for Two-Phase Coalbed Methane Wells

A method is proposed to predict the flowing bottomhole pressures （FBHPs） for two-phase coalbed methane （CBM） wells. The mathematical models for both gas column pressure and two-phase fluid column pressure were developed based on the well liquid flow equation. FBHPs during the production were predicted by considering the effect of entrained liquid on gravitational gradients. Comparison of calculated BHPs by Cullender-Smith and proposed method was also studied. The results show that the proposed algorithm gives the desired accuracy of calculating BHPs in the low- productivity and low-pressure CBM wells. FBHP is resulted from the combined action of wellhead pressure, gas column pressure and fluid column pressure. Variation of kinetic energy term, compressibility and friction factors with depth increments and liquid holdup with velocity should be considered to simulate the real BHPs adequately. BHP is a function of depth of each column segment. The small errors of less than 1.5% between the calculated and measured values are obtained with each segment within 25 m. Adjusting BHPs can effectively increase production pressure drop, which is beneficial to CBM desorption and enhances reservoir productivity. The increment of pressure drop from 5.37 MPa2 to 8.66 MPa2 leads to an increase of CBM production from 3270 m3/d to 6700 m3/d and is attributed to a decrease in BHP from 2.25 MPa to 1.33 MPa.

Spray Atomization and Structure of Supersonic Liquid Jet with Various Viscosities of Non-Newtonian Fluids

These experimental investigations are designed to study shock wave characteristics and spray structure. Supersonic liq- uid jets injected into ambient fields are empirically studied using projectile impacts in a two-stage light gas gun. This study looks primarily at the design of the nozzle assembly, the tip velocity of the high speed jet, the structure of the spray jet and the shock wave generation process. The supersonic liquid jets were visualized using an ultra high-speed camera and the schlieren system for visualization to quantitatively analyze the shock wave angle. The experimental re- sults with straight cone nozzle types and various non-Newtonian fluid viscosities are presented in this paper. The effects of nozzle geometry on the jet behavior are described. The characteristics of the shock wave generation and spray jet structure were found to be significantly related to the nozzle geometry. The expansion gases accelerated the projectile, which had a mass of 6 grams, from 250 m/s. As a result, it was found that the maximum jet velocity appeared in the liquid jet with high viscosity properties. Supersonic liquid jets, which occurred at the leading edge the shock waves and the compression waves in front of the jets, were observed. Also, the shock waves significantly affected the atomization process for each spray droplet.

Torque and bending moment acting on a flexible shaft agitated by disk turbines in a gas–liquid stirred vessel

The torque and bending moment acting on a flexible overhung shaft in a gas–liquid stirred vessel agitated by a Rushton turbine and three different curved-blade disk turbines(half circular blades disk turbine, half elliptical blades disk turbine, and parabolic blades disk turbine) were experimentally measured by a customized moment sensor. The results show that the amplitude distribution of torque can be fitted by a symmetric bimodal distribution for disk turbines, and generally the distribution is more dispersive as the blade curvature or the gas flow rate increases. The amplitude distribution of shaft bending moment can be fitted by an asymmetric Weibull distribution for disk turbines. The relative shaft bending moment manifests a "rising-falling-rising" trend over the gas flow number, which is a corporate contribution of the unstable gas–liquid flow around the impeller, the gas cavities behind the blades, and the direct impact of gas on the impeller. And the "falling" stage is greater and lasts wider over the gas flow number for Rushton turbine than for the curved-blade disk turbines.

RESEARCH ON METHOD TO CALCULATE VELOCITIES OF SOLID PHASE AND LIQUID PHASE IN DEBRIS FLOW

Velocities of solid phase and liquid phase in debris flow are one key problem to research on impact and abrasion mechanism of banks and control structures under action of debris flow. Debris flow was simplified as two-phase liquid composed of solid phase with the same diameter particles and liquid phase with the same mechanical features. Assume debris flow was one-dimension two-phase liquid moving to one direction, then general equations of velocities of solid phase and liquid phase were founded in two-phase theory. Methods to calculate average pressures, volume forces and surface forces of debris flow control volume were established. Specially, surface forces were ascertained using Bingham＇s rheology equation of liquid phase and Bagnold＇s testing results about interaction between particles of solid phase. Proportional coefficient of velocities between liquid phase and solid phase was put forward, meanwhile, divergent coefficient between theoretical velocity and real velocity of solid phase was provided too. To state succinctly before, method to calculate velocities of solid phase and liquid phase was obtained through solution to general equations. The method is suitable for both viscous debris flow and thin debris flow. Additionally, velocities every phase can be identified through analyzing deposits in-situ after occurring of debris flow. It is obvious from engineering case the result in the method is consistent to that in real-time field observation.

The primary controlling parameters of porosity, permeability,and seepage capability of tight gas reservoirs:a case study on Upper Paleozoic Formation in the eastern Ordos Basin,Northern China

Tight sandstone gas(hereafter"tight gas")has become a subject of unconventional gas exploration globally.The large-scale development and use of tight gas resources in the USA,in particular,facilitated the rapid rebound of natural gas production in the USA,in addition to driving the rapid development of tight gas worldwide.In the eastern Ordos Basin,the Upper Paleozoic feature includes multiple layers of gas,a shallow depth,and notable potential for exploration and development.However,the reservoirs in the area are relatively tight,exhibit strong heterogeneity,and possess a complex micropore structure,thus restricting the eff ective economic development of oil and gas.Thus,research on the primary parameters controlling pore throat structure and the seepage capability of low-permeability reservoirs will be beneficial for the effcient exploration and development of natural gas in the eastern Ordos Basin.The parameters of reservoir porosity and percolation ability,as well as permeability,were analyzed using systematic sampling of the of the Upper Paleozoic Benxi,Taiyuan,and Shanxi Formations in the eastern Ordos Basin,constant-rate mercury injection experiments,nuclear magnetic resonance analysis,and gas–water-phase experimental studies.The results indicate that reservoir porosity is controlled by the effective pore volume and number,whereas permeability is controlled by the largest throat radius,rather than the average.The effective pore volume controls the movable fluid saturation,while reservoir percolation capability is controlled by the effective pore volume,irreducible water saturation,and size of the gas–water two-phase seepage zone.

THE EFFECT OF LIQUID PHYSICAL PROPERTIES ON DRIFT VELOCITY

Drift velocity is a very important paramcter for predictirg the pool volumetric void fraction. Two-phase system of gas and high viscous liquids pool is encountered in various engineering applications. A review of the literature shows no data for explaining the effect of highly viscous liquids on the drift velocity. This paper’s analysis shows that there is a considerable influence. It is shown that the foaming behaviour of liquids is dependent on the surface properties. For some highly viscous liquids at a given superficial gas velocity, the viscosity changes with time. The effect of "foam" and "time" on drift velocity is clearly elucidated.

Experimental study of the movement of control fluid in compound perforation

The interaction between the high pressure gas and the control fluid and the movement mechanism of the control fluid in compound perforation were studied by a series of large-scale experiments, where the movement behavior of the control fluid was observed. The curves of measured pressure were analyzed, a mathematical model for the rigid movement of the control fluid was established, and the movement velocity of control fluid was analyzed. Moreover, the velocity from experimental results and velocity from an analytical solution were contrasted. The movement of the control fluid in the initial stage was similar to the rigid movement; however, the propagation of the pressure wave in the control fluid should be taken into account. Experimental results are significant for research on the movement mechanism of control fluid in compound perforation.

Numerical Case Study on the LDIE Degradation Occurred in the Vent Header of a High Pressure Feedwater Heater

Piping installed in nuclear power plants is affected by various types of degradation mechanisms and may be ruptured due to gradual thinning. The degradation mechanisms such as flow-accelerated corrosion (FAC), cavitation, liquid droplet impingement erosion (LDIE), etc., can lead to costly outages and repairs and possibly affect plant reliability. In August 2008, the header pipe in the high pressure feedwater heater vent system leaked at a Korean nuclear power plant. After cutting the pipe during refueling outage, it was identified that the leak was due to LDIE. This paper presents the numerical analysis results, using various multi-phase models of ANSYS FLUENT for the purpose of identifying the cause of the LDIE. The numerical analysis methods which are most similar to the damage of the pipe are proposed for the comparison of analysis results with each multi-phase model.

Recent advances in physical understanding and quantitative prediction of impinging-jet dynamics and atomization

Impinging-jet injectors are widely used in liquid propulsion applications, since their simple configuration provides reliable and efficient atomization. The flowfield involves a series of complicated spatio-temporal evolutions. Much effort has been directed toward understanding the underlying physics and developing quantitative predictions of impinging-jet atomization. This paper summarizes the recent advances in this direction, including state-of-the-art theoretical, experimental, and numerical studies, along with representative results. Finally, concluding remarks address remaining challenges and highlight modeling capabilities of high-fidelity simulations.

THE UNIFIED FORM OF RETENTION EQUATION OF CHROMATOGRAPHY

The unified form of retention equation of chromatography is suggested by adoptingstatistical thermodynamics and lattice theory. According to different conditions, the retentionformulas of GC, LC and SFC can be obtained from this unified equation. Those formulashave been confirmed by experimental data.