The study of liquid film characteristics in multiphase flow is a very important research topic, however,the characteristics of the liquid film around Taylor bubble structure in gas, oil and water three-phase flow are ...The study of liquid film characteristics in multiphase flow is a very important research topic, however,the characteristics of the liquid film around Taylor bubble structure in gas, oil and water three-phase flow are not clear. In the present study, a novel liquid film sensor is applied to measure the distributed signals of the liquid film in three-phase flow. Based on the liquid film signals, the liquid film characteristics including the structural characteristics and the nonlinear dynamics characteristics in three-phase flows are investigated for the first time. The structural characteristics including the proportion, the appearance frequency and the thickness of the liquid film are obtained and the influences of the liquid and gas superficial velocities and the oil content on them are investigated. To investigate the nonlinear dynamics characteristics of the liquid film with the changing flow conditions, the entropy analysis is introduced to successfully uncover and quantify the dynamic complexity of the liquid film behavior.展开更多
Particle fluctuation and gas turbulence in dense gas-particle flows are less studied due to complexity of the phenomena. In the present study, simulations of gas turbulent flows passing over a single particle are carr...Particle fluctuation and gas turbulence in dense gas-particle flows are less studied due to complexity of the phenomena. In the present study, simulations of gas turbulent flows passing over a single particle are carried out first by using RANS modeling with a Reynolds stress equation turbulence model and sufficiently fine grids, and then by using LES. The turbulence enhancement by the particle wake effect is studied under various particle sizes and relative gas velocities, and the turbulence enhancement is found proportional to the particle diameter and the square of velocity. Based on the above results, a turbulence enhancement model for the particle-wake effect is proposed and is incorporated as a sub-model into a comprehensive two-phase flow model, which is then used to simulate dilute gas-particle flows in a horizontal channel. The simulation results show that the predicted gas turbulence by using the present model accounting for the particle wake effect is obviously in better agreement with the experimental results than the prediction given by the model not accounting for the wake effect. Finally, the proposed model is incorporated into another two-phase flow model to simulate dense gasparticle flows in a downer. The results show that the particle wake effect not only enhances the gas turbulence, but also amplifies the particle fluctuation.展开更多
Based on the analysis of spectrum characteristics of intensity fluctuations while light beams pass through stack gas flow in an industrial setting, this paper puts emphasis upon discussing the spectrum of optical inte...Based on the analysis of spectrum characteristics of intensity fluctuations while light beams pass through stack gas flow in an industrial setting, this paper puts emphasis upon discussing the spectrum of optical intensity fluctuations by the variety of particle concentration in stack gas flow. This paper also gives the primary theoretical explanation of the measurement results in the stack of coal-fired utility boilers. Meanwhile, the cross-correlation formula is given as the theoretical basis of velocity measurement by using particle concentration scintillation.展开更多
Propellant gas flow has an important impact on the ionization and acceleration process of Hall effect thrusters (HETs). In this paper, a particle-in-cell numerical method is used to study the effect of the anode tem...Propellant gas flow has an important impact on the ionization and acceleration process of Hall effect thrusters (HETs). In this paper, a particle-in-cell numerical method is used to study the effect of the anode temperature, i.e., the flow speed of the propellant gas, on the discharge characteristics of a HET. The simulation results show that, no matter the magnitude of the discharge voltage, the calculated variation trends of performance parameters with the anode temperature are in good agreement with the experimental ones presented in the literature. Further mechanism analysis indicates that the magnitude of the electron temperature is responsible for the two opposing variation laws found under different discharge voltages. When the discharge voltage is low, the electron temperature is low, and so is the intensity of the propellant ionization; the variation of the thruster performance with the anode temperature is thereby determined by the variation of the neutral density that affects the propellant utilization efficiency. When the discharge voltage is high, the electron temperature is large enough to guarantee a high degree of the propellant utilization no matter the magnitude of the anode temperature. The change of the thruster performance with the anode temperature is thus dominated by the change of the electron temperature and consequently the electron-neutral collisions as well as the electron cross-field mobility that affect the current utilization efficiency.展开更多
The characteristics of the flowfields of a synthetic jet actuator are experimentally investigated with the slot-nozzle driven by the piezoelectric membrane. The particle image velocimetry (PIV) and the hot-wire anem...The characteristics of the flowfields of a synthetic jet actuator are experimentally investigated with the slot-nozzle driven by the piezoelectric membrane. The particle image velocimetry (PIV) and the hot-wire anemometer are utilized to measure the flowfields and the velocity profiles of the actuator with different actuating factors. Analytical results show that pairs of counter-rotating vortices are generated near the nozzle. With the development of the synthetic ject, the synthetic jet rapidly spreads in the slot-width direction; while in the slot-length direction, it contracts firstly and slowly spreads. The centerline velocity distribution has a up-down tendency varying with axial distances, and accelerates to its maximum at z/b= 10. The transverse velocity profile across the slot-width is centro-symmetric and self-similar. However, the velocity profiles across the slot-length are saddle-like near the nozzle. It shows that there are two resonance frequencies for the actuator. If the actuator works with the resonance frequency, the vorticity and the velocity of the synthetic jet are higher than those of other frequencies. Compared with the continuous jet, the synthetic jet shows special flow characteristics.展开更多
In order to research the influence of coal-rock mass morphology of mining space on the flow law of gas,the laboratory physical model and numerical computation methods were adopted to simulate coal mining activities.Th...In order to research the influence of coal-rock mass morphology of mining space on the flow law of gas,the laboratory physical model and numerical computation methods were adopted to simulate coal mining activities.The simulation results indicate that,after coal seam mining,the loose rock accumulation body of free caving,ordered rock arrangement body of plate damage rich in longitudinal and transverse fractures and horizontal fissure body formed by rock mass deformation imbalance are formed from bottom to top in the mining space.For these three types of accumulation bodies,there are essential differences in the accumulation state,rock size and gas breakover characteristics.According to this,the coal-rock mass in the mining space is classified into gas turbulence channel area,gas transitional flow channel area and gas seepage channel area.In the turbulence channel area,the gas is distributed transversely and longitudinally and gas diffuses in the form of convection with Reynolds number R_e more than100;in the transitional flow channel area,one-way or two-way gas channels are crisscross and gas is of transitional flow regime with R,.between 10 and 100.In the seepage channel area,there are a few vertical gas channels with R,.less than 10.In this paper,the researches on the gas orientation method in different partitions were further carried out,gas orientation methods of low-level pipe burying,middle-level interception and high-level extraction were determined and an on-site industrial test was conducted,achieving the effective diversion of gas and verifying the reasonableness of gas channel partition.展开更多
Recycling gas drilling is a new drilling technology. This paper can be divided into three parts, with the purpose of introducing and analyzing the characteristics of this new technology. First, the major equipment cha...Recycling gas drilling is a new drilling technology. This paper can be divided into three parts, with the purpose of introducing and analyzing the characteristics of this new technology. First, the major equipment characteristic of this technology was introduced. Secondly, compared with conventional gas drilling, Angel's model was used to analyze the wellbore flow characteristics. Due to the closed loop and the effect of back pressure caused by the equipment, the gas flow rate decreases dramatically during drilling. Apart from this, it is also found that the kinetic energy at the casing shoe is always smaller than that at the top of the collar. The proposing of the drilling limit concept points out the basic difference between the two gas drilling technologies. Lastly, according to the results of the theoretical analysis, gas supplement operations for the wellbore must be conducted. Thus, two gas supplement schemes are presented in this paper, to provide some guidance for field operations.展开更多
This study examined the evolution of morphology and nanostructure of soot particles from the plasma-flame interaction for various gas flow rates.The current study used both optical diagnostic and sampling methods to e...This study examined the evolution of morphology and nanostructure of soot particles from the plasma-flame interaction for various gas flow rates.The current study used both optical diagnostic and sampling methods to explore the soot production and combustion characteristics.Soot particles were characterized at the same positions downstream from the flame zone by thermophoretic sampling and transmission electron microscopy.Moreover,X-ray diffraction analysis,and thermogravimetric analysis were performed to study the nanostructure and oxidation reactivity of soot.A reduction in soot concentration was found with the plasma addition,which illustrated an inhibition effect of plasma on soot emission.The increased gas flow rate promoted soot concentration since a growing number of carbons participated in the combustion process.Depending on the gas flow rate(carbon content)variation and plasma activation,either liquid-like soot material with irregularly shaped protrusions or chain-like structure,or a mixture of both,were generated from the diffusion flames.The soot produced by plasma-flame interaction also demonstrated a high correlation between nanostructure and reactivity.The soot from lower carbon content with plasma activation had a shorter fringe length and larger fringe tortuosity related to higher oxidation reactivity.On the contrary,soot from the highest carbon content without plasma-flame interaction exhibited prevalent fullerene-like nanostructures with evident large or small shells and also had a higher carbonization degree resulting in lower oxidation reactivity.展开更多
Sedimentary process research is of great significance for understanding the distribution and characteristics of sediments.Through the detailed observation and measurement of the Sangyuan outcrop in Luanping Basin,this...Sedimentary process research is of great significance for understanding the distribution and characteristics of sediments.Through the detailed observation and measurement of the Sangyuan outcrop in Luanping Basin,this paper studies the depositional process of the hyperpycnal flow deposits,and divides their depositional process into three phases,namely,acceleration,erosion and deceleration.In the acceleration phase,hyperpycnal flow begins to enter the basin nearby,and then speeds up gradually.Deposits developed in the acceleration phase are reverse.In addition,the original deposits become unstable and are taken away by hyperpycnal flows under the eroding force.As a result,there are a lot of mixture of red mud pebbles outside the basin and gray mud pebbles within the basin.In the erosion phase,the reverse deposits are eroded and become thinner or even disappear.Therefore,no reverse grading characteristic is found in the proximal major channel that is closer to the source,but it is still preserved in the middle branch channel that is far from the source.After entering the deceleration phase,normally grading deposits appear and cover previous deposits.The final deposits in the basin are special.Some are reverse,and others are normal.They are superimposed with each other under the action of hyperpycnal flow.The analysis of the Sangyuan outcrop demonstrates the sedimentary process and distribution of hyperpycnites,and reasonably explain the sedimentary characteristics of hyperpycnites.It is helpful to the prediction of oil and gas exploration targets in gravity flow deposits.展开更多
A full-cycle numerical simulation of a circulating fluidized bed(CFB)by the use of the computational particle fluid dynamics(CPFD)method has been developed.The effects of the presence or absence of the secondary air,d...A full-cycle numerical simulation of a circulating fluidized bed(CFB)by the use of the computational particle fluid dynamics(CPFD)method has been developed.The effects of the presence or absence of the secondary air,different secondary air positions,and different secondary air ratios on the gas–solid flow characteristics were explored.The results show that the presence of the secondary air makes a core-annular structure of the velocity distribution of particles in the fluidized bed,which enhances the uniformity of particles’distribution and the stability of fluidization.The position and the ratio of the secondary air have a significant impact on the particle distribution,particle flow rate,and gas flow rate in the fluidized bed.When the secondary air position and ratio are optimal,the particles,particle flow rate,and air flow rate in the CFB are evenly distributed,the gas–solid flow state is good,and the CFB can operate stably.展开更多
The characteristics of swirler flow field, including cold flow field and combustion flow field, in gas tur- bine combustor with two-stage swirler are studied by using particle image velocimetry (PIV). Velocity compo...The characteristics of swirler flow field, including cold flow field and combustion flow field, in gas tur- bine combustor with two-stage swirler are studied by using particle image velocimetry (PIV). Velocity compo- nents, fluctuation velocity, Reynolds stress and recirculation zone length are obtained, respectively. Influences of geometric parameter of primary hole, arrangement of primary hole, inlet air temperature, first-stage swirler an- gle and fuel/air ratio on flow field are investigated, respectively. The experimental results reveal that the primary recirculation zone lengths of combustion flow field are shorter than those of cold flow field, and the primary reeir- culation zone lengths decrease with the increase of inlet air temperature and fuel/air ratio. The change of the geo- metric parameter of primary hole casts an important influence on the swirler flow field in two-stage swirler com- bustor.展开更多
Sandy debris flow is a new genetic type of sand bodies,which has gained much attention in recent years and its corresponding theory is proved to be a significant improvement and even partial denial to the 'Bouma S...Sandy debris flow is a new genetic type of sand bodies,which has gained much attention in recent years and its corresponding theory is proved to be a significant improvement and even partial denial to the 'Bouma Sequence' and 'turbidite fan' deep-water sedimentary theories to some point. Oil exploration researchers are highly concerned with sandy debris flows for its key role in controlling oil and gas accumulation processes.In this article,by applying sandy debris flows theory and combining a lot work of core,outcrop observation and analysis plus seismic profile interpretation,we recognized three types of sedimentary gravity flows that are sandy debris flows,classic turbidites and slumping rocks in chang-6 member of Yanchang Formation in the deep-water area of central Ordos Basin.Among the three types,the sandy debris flows are the most prominent and possesses the best oil bearing conditions.On the contrary,the classic turbidites formed by turbidity currents are limited in distribution;therefore,previous Yanchang Formation deep-water sedimentary studies have exaggerated the importance of turbidite currents deposition.Further study showed that the area distribution of deep water gravity flow sand bodies in Yanchang Formation were controlled by the slope of the deep-water deposits and the flows had vast distribution,huge depth and prevalent advantages for oil forming,which make it one of the most favorable new areas for Ordos Basin prospecting.展开更多
The permeability of coal ahead of the working face obviously changes dues to changes in abutment pressure.The formation and evolution of gas flow channels within the abutment pressure area was studied by analyzing the...The permeability of coal ahead of the working face obviously changes dues to changes in abutment pressure.The formation and evolution of gas flow channels within the abutment pressure area was studied by analyzing the fracture extension mechanism and fracture development in different zones of the abutment pressure area.Fracture and damage mechanics theory is used to understand the observations.The following two techniques were used to understand the evolution of gas flow channels:field observation of the characteristic fractures at different positions relative to the working face and fluorescence micrographs of prepared coal samples.Bending tensile fractures develop along an approximately vertical direction that forms a microscopic network of channels in areas of stress concentration.The abutment pressure affects the local stress and,hence,the local gas conduction.The fractures induced by large deformation and plastic flow form macroscopically networked channels in the reduced stress area.Closer to the working face the gas flow channels evolve from microscopic to macroscopic and from isolated to network.Gas permeability continuously increases during this time.This is corroborated by field observations of the displacement of top coal and the gas flow from gas extraction drillings.展开更多
A three-dimensional(3D) fast fluidized bed with the riser of 3.0 m in height and 0.1 m in inner diameter was established to experimentally study the cluster behaviors of Geldart B particles. Five kinds of quartz sand ...A three-dimensional(3D) fast fluidized bed with the riser of 3.0 m in height and 0.1 m in inner diameter was established to experimentally study the cluster behaviors of Geldart B particles. Five kinds of quartz sand particles(dp= 0.100, 0.139, 0.177, 0.250 and 0.375 mm and ρp= 2480 kg·m^(-3)) were respectively investigated, with the total mass of the bed material kept as 10 kg. The superficial gas velocity in the riser ranges from 2.486 to 5.594 m·s^(-1) and the solid mass flux alters from 30 to 70 kg·((m^(-2)·s))^(-1). Cluster characteristics and evolutionary processes in the different positions of the riser were captured by the cluster visualization systems and analyzed by the self-developed binary image processing. The results found four typical cluster structures in the riser,i.e., the macro stripe-shaped cluster, saddle-shaped cluster, U-shaped cluster and the micro cluster. The increasing superficial gas velocity and particle sizes result in the increasing average cluster size and the decreasing cluster time fraction, while the solid mass flux in the riser have the reverse influences on the cluster size and time fraction. Additionally, clusters in the upper region of the riser often have the larger size and time fraction than that in the lower region. All these effects of operating conditions on clusters become less obvious when particle size is less than 0.100 mm.展开更多
In this work, a novel direct current (DC) atmospheric pressure rotating gliding arc (RGA) plasma reactor has been developed for plasma-assisted chemical reactions. The influence of the gas composition and the gas ...In this work, a novel direct current (DC) atmospheric pressure rotating gliding arc (RGA) plasma reactor has been developed for plasma-assisted chemical reactions. The influence of the gas composition and the gas flow rate on the arc dynamic behaviour and the formation of reactive species in the N2 and air gliding arc plasmas has been investigated by means of electrical signals, high speed photography, and optical emission spectroscopic diagnostics. Compared to conventional gliding arc reactors with knife-shaped electrodes which generally require a high flow rate (e.g., 10-20 L/min) to maintain a long arc length and reasonable plasma discharge zone, in this RGA system, a lower gas flow rate (e.g., 2 L/min) can also generate a larger effective plasma reaction zone with a longer arc length for chemical reactions. Two different motion patterns can be clearly observed in the N2 and air RGA plasmas. The time-resolved arc voltage signals show that three different arc dynamic modes, the arc restrike mode, takeover mode, and combined modes, can be clearly identified in the RGA plasmas. The occurrence of different motion and arc dynamic modes is strongly dependent on the composition of the working gas and gas flow rate.展开更多
Numerical research on the dilute particles movement and deposition characteristics in the vicinity of converging slot-hole(console) was carried out, and the effect of hole shape on the particle deposition characterist...Numerical research on the dilute particles movement and deposition characteristics in the vicinity of converging slot-hole(console) was carried out, and the effect of hole shape on the particle deposition characteristics was investigated. The EI-Batsh deposition model was used to predict the particle deposition characteristics. The results show that the console hole has an obvious advantage in reducing particle deposition in comparison with cylindrical hole, especially under higher blowing ratio. The coolant jet from console holes can cover the wall well. Furthermore, the rotation direction of vortices near console hole is contrary to that near cylindrical hole. For console holes, particle deposition mainly takes place in the upstream area of the holes.展开更多
In this paper, the three_dimensional vo rtex filament method was used to simulate the evolution of vortex structures in the axisymmetric round jet. The results agree well with the ones given by Chung and Troutt. The...In this paper, the three_dimensional vo rtex filament method was used to simulate the evolution of vortex structures in the axisymmetric round jet. The results agree well with the ones given by Chung and Troutt. Then one_coupling model was employed to calculate the particle motio n based on the computed flows. The results show that the particle motion is affe cted by flows obviously at the case of particle number St1 and negligibly at St1 ,particles distribute around the vortex structures uniformly at St ~1 . When perturbations with wavenumber 5 are introduced to vortex rings, part icles disperse wider along radial direction, which conforms to the experimental results. The degree of particle dispersion is in the direct ratio to the amplitu de of perturbation. The conclusions given in the paper are useful to the practic e usage.展开更多
The effects of feed gas flow rate and operating current on the electrical characteristics and dynamic behavior of a rotating gliding arc (RGA) plasma codriven by a magnetic field and tangential flow were investigate...The effects of feed gas flow rate and operating current on the electrical characteristics and dynamic behavior of a rotating gliding arc (RGA) plasma codriven by a magnetic field and tangential flow were investigated.The operating current has been shown to significantly affect the time-resolved voltage waveforms of the discharge,particularly at flow rate =21 min^-1.When the current was lower than 140 mA,sinusoidal waveforms with regular variation periods of 13.5-17.0 ms can be observed (flow rate =21 min^-1).The restrike mode characterized by serial sudden drops of voltage appeared under all studied conditions.Increasing the flow rate from 8 to 121 min^-1 (at the same current) led to a shift of arc rotation mode which would then result in a significant drop of discharge voltage (around 120-200 V).For a given flow rate,the reduction of current resulted in a nearly linear increase of voltage.展开更多
A computational fluid dynamics(CFD)study of the impact characteristics and stagnation formation on a solid target surface by an abrasive waterjet at supersonic velocities is presented to understand the impact process....A computational fluid dynamics(CFD)study of the impact characteristics and stagnation formation on a solid target surface by an abrasive waterjet at supersonic velocities is presented to understand the impact process.A CFD model is developed and verified by experimental water and particle velocities and then used to simulate the jet impact process.The trends of the stagnation formation and its effect on the jet flow with respect to the jetting and impacting parameters are amply discussed.It is found that stagnation formation at the impact site increases with an increase in the impact time,nozzle standoff distance and nozzle diameter,while the initial peak velocity at the nozzle exit has little effect on the size of the stagnation zone.It is shown that stagnation markedly changes the water and particle flow direction,so that the particle impact angle is varied and the jet impact area is enlarged.The jet structure may be classified to have a free jet flow region,a jet deflection region with a stagnation zone and a wall jet region.Furthermore,the stagnation affects significantly the waterjet and particle energy transferred to the target surface.The average particle velocity across the jet is reduced by approximately one third due to the damping effect of the stagnation under the conditions considered in this study.展开更多
基金supported by the National Natural Science Foundation of China (42074142, 51527805, 41974139)China Postdoctoral Science Foundation (2020M680969, 2021T140099)the Fundamental Research Funds for the Central Universities (N2104013)。
文摘The study of liquid film characteristics in multiphase flow is a very important research topic, however,the characteristics of the liquid film around Taylor bubble structure in gas, oil and water three-phase flow are not clear. In the present study, a novel liquid film sensor is applied to measure the distributed signals of the liquid film in three-phase flow. Based on the liquid film signals, the liquid film characteristics including the structural characteristics and the nonlinear dynamics characteristics in three-phase flows are investigated for the first time. The structural characteristics including the proportion, the appearance frequency and the thickness of the liquid film are obtained and the influences of the liquid and gas superficial velocities and the oil content on them are investigated. To investigate the nonlinear dynamics characteristics of the liquid film with the changing flow conditions, the entropy analysis is introduced to successfully uncover and quantify the dynamic complexity of the liquid film behavior.
基金The project supported by the National Natural Science Foundation of China(50606026 and 50736006)
文摘Particle fluctuation and gas turbulence in dense gas-particle flows are less studied due to complexity of the phenomena. In the present study, simulations of gas turbulent flows passing over a single particle are carried out first by using RANS modeling with a Reynolds stress equation turbulence model and sufficiently fine grids, and then by using LES. The turbulence enhancement by the particle wake effect is studied under various particle sizes and relative gas velocities, and the turbulence enhancement is found proportional to the particle diameter and the square of velocity. Based on the above results, a turbulence enhancement model for the particle-wake effect is proposed and is incorporated as a sub-model into a comprehensive two-phase flow model, which is then used to simulate dilute gas-particle flows in a horizontal channel. The simulation results show that the predicted gas turbulence by using the present model accounting for the particle wake effect is obviously in better agreement with the experimental results than the prediction given by the model not accounting for the wake effect. Finally, the proposed model is incorporated into another two-phase flow model to simulate dense gasparticle flows in a downer. The results show that the particle wake effect not only enhances the gas turbulence, but also amplifies the particle fluctuation.
文摘Based on the analysis of spectrum characteristics of intensity fluctuations while light beams pass through stack gas flow in an industrial setting, this paper puts emphasis upon discussing the spectrum of optical intensity fluctuations by the variety of particle concentration in stack gas flow. This paper also gives the primary theoretical explanation of the measurement results in the stack of coal-fired utility boilers. Meanwhile, the cross-correlation formula is given as the theoretical basis of velocity measurement by using particle concentration scintillation.
基金funded by National Natural Science Foundation of China(Nos.51507040,51736003 and 51777045)the Research Program(No.JSZL2016203C006)the Fundamental Research Funds for the Central Universities(No.HIT.NSRIF.2015079)
文摘Propellant gas flow has an important impact on the ionization and acceleration process of Hall effect thrusters (HETs). In this paper, a particle-in-cell numerical method is used to study the effect of the anode temperature, i.e., the flow speed of the propellant gas, on the discharge characteristics of a HET. The simulation results show that, no matter the magnitude of the discharge voltage, the calculated variation trends of performance parameters with the anode temperature are in good agreement with the experimental ones presented in the literature. Further mechanism analysis indicates that the magnitude of the electron temperature is responsible for the two opposing variation laws found under different discharge voltages. When the discharge voltage is low, the electron temperature is low, and so is the intensity of the propellant ionization; the variation of the thruster performance with the anode temperature is thereby determined by the variation of the neutral density that affects the propellant utilization efficiency. When the discharge voltage is high, the electron temperature is large enough to guarantee a high degree of the propellant utilization no matter the magnitude of the anode temperature. The change of the thruster performance with the anode temperature is thus dominated by the change of the electron temperature and consequently the electron-neutral collisions as well as the electron cross-field mobility that affect the current utilization efficiency.
文摘The characteristics of the flowfields of a synthetic jet actuator are experimentally investigated with the slot-nozzle driven by the piezoelectric membrane. The particle image velocimetry (PIV) and the hot-wire anemometer are utilized to measure the flowfields and the velocity profiles of the actuator with different actuating factors. Analytical results show that pairs of counter-rotating vortices are generated near the nozzle. With the development of the synthetic ject, the synthetic jet rapidly spreads in the slot-width direction; while in the slot-length direction, it contracts firstly and slowly spreads. The centerline velocity distribution has a up-down tendency varying with axial distances, and accelerates to its maximum at z/b= 10. The transverse velocity profile across the slot-width is centro-symmetric and self-similar. However, the velocity profiles across the slot-length are saddle-like near the nozzle. It shows that there are two resonance frequencies for the actuator. If the actuator works with the resonance frequency, the vorticity and the velocity of the synthetic jet are higher than those of other frequencies. Compared with the continuous jet, the synthetic jet shows special flow characteristics.
基金Financial supports for this work,provided by the State Key Basic Research Program of China(No.2011CB201204)
文摘In order to research the influence of coal-rock mass morphology of mining space on the flow law of gas,the laboratory physical model and numerical computation methods were adopted to simulate coal mining activities.The simulation results indicate that,after coal seam mining,the loose rock accumulation body of free caving,ordered rock arrangement body of plate damage rich in longitudinal and transverse fractures and horizontal fissure body formed by rock mass deformation imbalance are formed from bottom to top in the mining space.For these three types of accumulation bodies,there are essential differences in the accumulation state,rock size and gas breakover characteristics.According to this,the coal-rock mass in the mining space is classified into gas turbulence channel area,gas transitional flow channel area and gas seepage channel area.In the turbulence channel area,the gas is distributed transversely and longitudinally and gas diffuses in the form of convection with Reynolds number R_e more than100;in the transitional flow channel area,one-way or two-way gas channels are crisscross and gas is of transitional flow regime with R,.between 10 and 100.In the seepage channel area,there are a few vertical gas channels with R,.less than 10.In this paper,the researches on the gas orientation method in different partitions were further carried out,gas orientation methods of low-level pipe burying,middle-level interception and high-level extraction were determined and an on-site industrial test was conducted,achieving the effective diversion of gas and verifying the reasonableness of gas channel partition.
基金financial support from the National Natural Science Foundation of China (50974021)Major Project of Chinese National Programs for Fundamental Research and Development (973 Program:2010CB226704)
文摘Recycling gas drilling is a new drilling technology. This paper can be divided into three parts, with the purpose of introducing and analyzing the characteristics of this new technology. First, the major equipment characteristic of this technology was introduced. Secondly, compared with conventional gas drilling, Angel's model was used to analyze the wellbore flow characteristics. Due to the closed loop and the effect of back pressure caused by the equipment, the gas flow rate decreases dramatically during drilling. Apart from this, it is also found that the kinetic energy at the casing shoe is always smaller than that at the top of the collar. The proposing of the drilling limit concept points out the basic difference between the two gas drilling technologies. Lastly, according to the results of the theoretical analysis, gas supplement operations for the wellbore must be conducted. Thus, two gas supplement schemes are presented in this paper, to provide some guidance for field operations.
基金supported by the National Natural Science Foundation of China(Grant Nos.52076110 and 52376115)。
文摘This study examined the evolution of morphology and nanostructure of soot particles from the plasma-flame interaction for various gas flow rates.The current study used both optical diagnostic and sampling methods to explore the soot production and combustion characteristics.Soot particles were characterized at the same positions downstream from the flame zone by thermophoretic sampling and transmission electron microscopy.Moreover,X-ray diffraction analysis,and thermogravimetric analysis were performed to study the nanostructure and oxidation reactivity of soot.A reduction in soot concentration was found with the plasma addition,which illustrated an inhibition effect of plasma on soot emission.The increased gas flow rate promoted soot concentration since a growing number of carbons participated in the combustion process.Depending on the gas flow rate(carbon content)variation and plasma activation,either liquid-like soot material with irregularly shaped protrusions or chain-like structure,or a mixture of both,were generated from the diffusion flames.The soot produced by plasma-flame interaction also demonstrated a high correlation between nanostructure and reactivity.The soot from lower carbon content with plasma activation had a shorter fringe length and larger fringe tortuosity related to higher oxidation reactivity.On the contrary,soot from the highest carbon content without plasma-flame interaction exhibited prevalent fullerene-like nanostructures with evident large or small shells and also had a higher carbonization degree resulting in lower oxidation reactivity.
基金the Scientific research and technology development project of Petro China(2021DJ5303)。
文摘Sedimentary process research is of great significance for understanding the distribution and characteristics of sediments.Through the detailed observation and measurement of the Sangyuan outcrop in Luanping Basin,this paper studies the depositional process of the hyperpycnal flow deposits,and divides their depositional process into three phases,namely,acceleration,erosion and deceleration.In the acceleration phase,hyperpycnal flow begins to enter the basin nearby,and then speeds up gradually.Deposits developed in the acceleration phase are reverse.In addition,the original deposits become unstable and are taken away by hyperpycnal flows under the eroding force.As a result,there are a lot of mixture of red mud pebbles outside the basin and gray mud pebbles within the basin.In the erosion phase,the reverse deposits are eroded and become thinner or even disappear.Therefore,no reverse grading characteristic is found in the proximal major channel that is closer to the source,but it is still preserved in the middle branch channel that is far from the source.After entering the deceleration phase,normally grading deposits appear and cover previous deposits.The final deposits in the basin are special.Some are reverse,and others are normal.They are superimposed with each other under the action of hyperpycnal flow.The analysis of the Sangyuan outcrop demonstrates the sedimentary process and distribution of hyperpycnites,and reasonably explain the sedimentary characteristics of hyperpycnites.It is helpful to the prediction of oil and gas exploration targets in gravity flow deposits.
基金the National Key Research and Development Program of China(grant No.2022YFC2904401)Guangxi Science and Technology Major Project(grant No.GuiKe AA23023033).
文摘A full-cycle numerical simulation of a circulating fluidized bed(CFB)by the use of the computational particle fluid dynamics(CPFD)method has been developed.The effects of the presence or absence of the secondary air,different secondary air positions,and different secondary air ratios on the gas–solid flow characteristics were explored.The results show that the presence of the secondary air makes a core-annular structure of the velocity distribution of particles in the fluidized bed,which enhances the uniformity of particles’distribution and the stability of fluidization.The position and the ratio of the secondary air have a significant impact on the particle distribution,particle flow rate,and gas flow rate in the fluidized bed.When the secondary air position and ratio are optimal,the particles,particle flow rate,and air flow rate in the CFB are evenly distributed,the gas–solid flow state is good,and the CFB can operate stably.
基金Supported by the National Natural Science Foundation of China(50906040)the Nanjing University of Aeronautics and Astronautics Research Funding(NZ2012107,NS2010052)~~
文摘The characteristics of swirler flow field, including cold flow field and combustion flow field, in gas tur- bine combustor with two-stage swirler are studied by using particle image velocimetry (PIV). Velocity compo- nents, fluctuation velocity, Reynolds stress and recirculation zone length are obtained, respectively. Influences of geometric parameter of primary hole, arrangement of primary hole, inlet air temperature, first-stage swirler an- gle and fuel/air ratio on flow field are investigated, respectively. The experimental results reveal that the primary recirculation zone lengths of combustion flow field are shorter than those of cold flow field, and the primary reeir- culation zone lengths decrease with the increase of inlet air temperature and fuel/air ratio. The change of the geo- metric parameter of primary hole casts an important influence on the swirler flow field in two-stage swirler com- bustor.
文摘Sandy debris flow is a new genetic type of sand bodies,which has gained much attention in recent years and its corresponding theory is proved to be a significant improvement and even partial denial to the 'Bouma Sequence' and 'turbidite fan' deep-water sedimentary theories to some point. Oil exploration researchers are highly concerned with sandy debris flows for its key role in controlling oil and gas accumulation processes.In this article,by applying sandy debris flows theory and combining a lot work of core,outcrop observation and analysis plus seismic profile interpretation,we recognized three types of sedimentary gravity flows that are sandy debris flows,classic turbidites and slumping rocks in chang-6 member of Yanchang Formation in the deep-water area of central Ordos Basin.Among the three types,the sandy debris flows are the most prominent and possesses the best oil bearing conditions.On the contrary,the classic turbidites formed by turbidity currents are limited in distribution;therefore,previous Yanchang Formation deep-water sedimentary studies have exaggerated the importance of turbidite currents deposition.Further study showed that the area distribution of deep water gravity flow sand bodies in Yanchang Formation were controlled by the slope of the deep-water deposits and the flows had vast distribution,huge depth and prevalent advantages for oil forming,which make it one of the most favorable new areas for Ordos Basin prospecting.
基金supported by a Grant from the State Key Basic Research Program of China(No.2011CB201204)the Central University Basic Scientific Research Business Expenses(No.2011ZY05)
文摘The permeability of coal ahead of the working face obviously changes dues to changes in abutment pressure.The formation and evolution of gas flow channels within the abutment pressure area was studied by analyzing the fracture extension mechanism and fracture development in different zones of the abutment pressure area.Fracture and damage mechanics theory is used to understand the observations.The following two techniques were used to understand the evolution of gas flow channels:field observation of the characteristic fractures at different positions relative to the working face and fluorescence micrographs of prepared coal samples.Bending tensile fractures develop along an approximately vertical direction that forms a microscopic network of channels in areas of stress concentration.The abutment pressure affects the local stress and,hence,the local gas conduction.The fractures induced by large deformation and plastic flow form macroscopically networked channels in the reduced stress area.Closer to the working face the gas flow channels evolve from microscopic to macroscopic and from isolated to network.Gas permeability continuously increases during this time.This is corroborated by field observations of the displacement of top coal and the gas flow from gas extraction drillings.
基金Supported by the National Key R&D Program of China[2016YFB0600802]the National Natural Science Foundation of China[51390492,51325601]
文摘A three-dimensional(3D) fast fluidized bed with the riser of 3.0 m in height and 0.1 m in inner diameter was established to experimentally study the cluster behaviors of Geldart B particles. Five kinds of quartz sand particles(dp= 0.100, 0.139, 0.177, 0.250 and 0.375 mm and ρp= 2480 kg·m^(-3)) were respectively investigated, with the total mass of the bed material kept as 10 kg. The superficial gas velocity in the riser ranges from 2.486 to 5.594 m·s^(-1) and the solid mass flux alters from 30 to 70 kg·((m^(-2)·s))^(-1). Cluster characteristics and evolutionary processes in the different positions of the riser were captured by the cluster visualization systems and analyzed by the self-developed binary image processing. The results found four typical cluster structures in the riser,i.e., the macro stripe-shaped cluster, saddle-shaped cluster, U-shaped cluster and the micro cluster. The increasing superficial gas velocity and particle sizes result in the increasing average cluster size and the decreasing cluster time fraction, while the solid mass flux in the riser have the reverse influences on the cluster size and time fraction. Additionally, clusters in the upper region of the riser often have the larger size and time fraction than that in the lower region. All these effects of operating conditions on clusters become less obvious when particle size is less than 0.100 mm.
基金supported by National Natural Science Foundation of China(No.51576174)the Specialized Research Fund for the Doctoral Program of Higher Education of China(No.20120101110099)the Fundamental Research Funds for the Central Universities(No.2015FZA4011)
文摘In this work, a novel direct current (DC) atmospheric pressure rotating gliding arc (RGA) plasma reactor has been developed for plasma-assisted chemical reactions. The influence of the gas composition and the gas flow rate on the arc dynamic behaviour and the formation of reactive species in the N2 and air gliding arc plasmas has been investigated by means of electrical signals, high speed photography, and optical emission spectroscopic diagnostics. Compared to conventional gliding arc reactors with knife-shaped electrodes which generally require a high flow rate (e.g., 10-20 L/min) to maintain a long arc length and reasonable plasma discharge zone, in this RGA system, a lower gas flow rate (e.g., 2 L/min) can also generate a larger effective plasma reaction zone with a longer arc length for chemical reactions. Two different motion patterns can be clearly observed in the N2 and air RGA plasmas. The time-resolved arc voltage signals show that three different arc dynamic modes, the arc restrike mode, takeover mode, and combined modes, can be clearly identified in the RGA plasmas. The occurrence of different motion and arc dynamic modes is strongly dependent on the composition of the working gas and gas flow rate.
基金Project(51276090) supported by the National Natural Science Foundation of ChinaProject(CXLX13_166) supported by Funding of Jiangsu Innovation Program for Graduate EducationProject supported by the Fundamental Research Funds for the Central Universities,China
文摘Numerical research on the dilute particles movement and deposition characteristics in the vicinity of converging slot-hole(console) was carried out, and the effect of hole shape on the particle deposition characteristics was investigated. The EI-Batsh deposition model was used to predict the particle deposition characteristics. The results show that the console hole has an obvious advantage in reducing particle deposition in comparison with cylindrical hole, especially under higher blowing ratio. The coolant jet from console holes can cover the wall well. Furthermore, the rotation direction of vortices near console hole is contrary to that near cylindrical hole. For console holes, particle deposition mainly takes place in the upstream area of the holes.
文摘In this paper, the three_dimensional vo rtex filament method was used to simulate the evolution of vortex structures in the axisymmetric round jet. The results agree well with the ones given by Chung and Troutt. Then one_coupling model was employed to calculate the particle motio n based on the computed flows. The results show that the particle motion is affe cted by flows obviously at the case of particle number St1 and negligibly at St1 ,particles distribute around the vortex structures uniformly at St ~1 . When perturbations with wavenumber 5 are introduced to vortex rings, part icles disperse wider along radial direction, which conforms to the experimental results. The degree of particle dispersion is in the direct ratio to the amplitu de of perturbation. The conclusions given in the paper are useful to the practic e usage.
基金supported by National Natural Science Foundation of China(51576174)
文摘The effects of feed gas flow rate and operating current on the electrical characteristics and dynamic behavior of a rotating gliding arc (RGA) plasma codriven by a magnetic field and tangential flow were investigated.The operating current has been shown to significantly affect the time-resolved voltage waveforms of the discharge,particularly at flow rate =21 min^-1.When the current was lower than 140 mA,sinusoidal waveforms with regular variation periods of 13.5-17.0 ms can be observed (flow rate =21 min^-1).The restrike mode characterized by serial sudden drops of voltage appeared under all studied conditions.Increasing the flow rate from 8 to 121 min^-1 (at the same current) led to a shift of arc rotation mode which would then result in a significant drop of discharge voltage (around 120-200 V).For a given flow rate,the reduction of current resulted in a nearly linear increase of voltage.
基金The project was financially supported by the Australian Research Council(ARC)under the Discovery-Projects scheme.K T would like to thank the Royal Thai Government for providing a PhD scholarship for this study.
文摘A computational fluid dynamics(CFD)study of the impact characteristics and stagnation formation on a solid target surface by an abrasive waterjet at supersonic velocities is presented to understand the impact process.A CFD model is developed and verified by experimental water and particle velocities and then used to simulate the jet impact process.The trends of the stagnation formation and its effect on the jet flow with respect to the jetting and impacting parameters are amply discussed.It is found that stagnation formation at the impact site increases with an increase in the impact time,nozzle standoff distance and nozzle diameter,while the initial peak velocity at the nozzle exit has little effect on the size of the stagnation zone.It is shown that stagnation markedly changes the water and particle flow direction,so that the particle impact angle is varied and the jet impact area is enlarged.The jet structure may be classified to have a free jet flow region,a jet deflection region with a stagnation zone and a wall jet region.Furthermore,the stagnation affects significantly the waterjet and particle energy transferred to the target surface.The average particle velocity across the jet is reduced by approximately one third due to the damping effect of the stagnation under the conditions considered in this study.