THEORETICAL INVESTIGATION ON HEAT TRANSFER CHARACTERISTICS WITH ROTATING THERMAL SOURCE

By reduction to one dimensional, periodic as well as rotating pulse heat sources, investigation on heat transfer characteristics with rotating body is carried out. Similar to the fluid flow, a new set of dimensionless numbers, namely quasi-Peclet numbers Pe 1, Pe 2 and Biot number Bi composed of angular velocity ω , thermophysical parameter, and geometry size are proposed, and applied to the dimensionless equations. Simulation result shows that it plays a decisive role in the process of the heat transfer. However, more important is that the numerical simulation depicts the difference between microcosmic and macroscopic structures of the temperature distribution, and reveals the influence of the relative relation of the dimensionless criterion numbers upon heat transfer characteristics.

Characteristics of Fin Baffle Packing Used in Rotating Packed Bed

For an alcohol/water system and with fin baffle packing,continuous distillation experiments were carried out in a rotating packed bed(RPB)system at atmospheric pressure.The effects of the average high gravity factor(β),liquid reflux ratio(R)and feedstock flux(F)on the momentum transfer and mass transfer were investigated. The gas phase pressure drop of RPB increased with the average high gravity factor,liquid reflux ratio and feedstock flux,which was 13.55-64.37 Pa atβof 2.01-51.49,R of 1.0-2.5,and F of 8-24 L·h1for a theoretical tray in the RPB with fin baffle packing.The investigation on the mass transfer in the RPB with different packings showed that the number of transfer units of RPB with a packing also increased with the average high gravity factor,reflux ratio and feedstock flux.It is found that the fin baffle packing(packing III)presents the best mass transfer performance and lowest pressure drop for the height equivalent to a theoretical plate(HETP),which is 6.59-9.84 mm.

Experimental research on the instability propagation characteristics of liquid kerosene rotating detonation wave

In order to study the instability propagation characteristics of the liquid kerosene rotating detonation wave(RDW),a series of experimental tests were carried out on the rotating detonation combustor(RDC)with air-heater.The fuel and oxidizer are room-temperature liquid kerosene and preheated oxygenenriched air,respectively.The experimental tests keep the equivalence ratio of 0.81 and the oxygen mass fraction of 35%unchanged,and the total mass flow rate is maintained at about 1000 g/s,changing the total temperature of the oxygen-enriched air from 620 K to 860 K.Three different types of instability were observed in the experiments:temporal and spatial instability,mode transition and re-initiation.The interaction between RDW and supply plenum may be the main reason for the fluctuations of detonation wave velocity and pressure peaks with time.Moreover,the inconsistent mixing of fuel and oxidizer at different circumferential positions is related to RDW oscillate spatially.The phenomenon of single-double-single wave transition is analyzed.During the transition,the initial RDW weakens until disappears,and the compression wave strengthens until it becomes a new RDWand propagates steadily.The increased deflagration between the detonation products and the fresh gas layer caused by excessively high temperature is one of the reasons for the RDC quenching and re-initiation.

VIBRATION RESPONSE AND ITS CHARACTERISTICS OF CENTRIFUGAL COMPRESSOR WITH ROTATING STALL

Based on the beginning, propagating and ending mechanism of rotating-stallcell, the relation between the pressure history signal and the pressure distribution along rotorcircumference is proposed. The angular velocities of rotating-stall cell propagating are computedfrom time series picked by the pressure probes on a cross section. Self-relation calculatingfiltered the random noise of the pressure history data. The exciting load on rotor is computed byintegral of filtered pressure signal along rotor circumference. By Prohl-Myklestad method, dynamicalequations of rotor system are obtained. The dynamical response of rotor system is resolved by usingMatlab system. Further more, the situation of more than one of stall cells is discussed. Two casesrespectively from the natural gas compressor of some fertilizer plant and the CO_2 compressor ofsome nitrogenous fertilizer plant demonstrate that both methods of calculating the load exerted onrotor by pressure fluctuation and resolving the dynamic response of rotor are available and thecharacteristics of frequency spectrum of rotating stall are correct.

The characteristics of welding currents in a rotating arc leadtandem GMAW process and the weld-seam tracking

Tandem gas metal arc welding （ T-GMAW） process shows a high deposition rate that up to three times o f the single electrode GMAW, so the welding speed could be significantly increased in this process. However, the majority o f this process applications are based on the pre-programmed robotic welding, which does not allow them to track the seam real-time during welding. Rotating arc sensor, sensing the seam position by detecting the changing of welding currents, has been widely adopted in the automatic robot welding process. It is proposed in this paper to integrate the rotating arc sensor with a trailing torch to develop a new approach of rotating arc lead tandem gas metal arc welding （RLT-GMAW） process. The characteristics of the welding currents in the proposed new welding process were firstly studied, and then a self-turning fuzzy control seam tracking strategy was developed for the mobile robot automatic welding. The experimental results showed that the proposed RLT-GMAW process had an excellent seam tracking performance and high welding deposition rate. Even if there were some electromagnetic interactions between the two arcs, the deviation of the welding seam could also be reflected by the fluctuation of the welding currents on the leading arc once the correct welding parameters were selected. Based on the detected deviation, the welding tracking experiments showed that the proposed self-turning fuzzy controller had a good performance for the RLT-GMAW process seam tracking.

Characteristics of Atmospheric Pressure Rotating Gliding Arc Plasmas

In this work, a novel direct current （DC） atmospheric pressure rotating gliding arc （RGA） plasma reactor has been developed for plasma-assisted chemical reactions. The influence of the gas composition and the gas flow rate on the arc dynamic behaviour and the formation of reactive species in the N2 and air gliding arc plasmas has been investigated by means of electrical signals, high speed photography, and optical emission spectroscopic diagnostics. Compared to conventional gliding arc reactors with knife-shaped electrodes which generally require a high flow rate （e.g., 10-20 L/min） to maintain a long arc length and reasonable plasma discharge zone, in this RGA system, a lower gas flow rate （e.g., 2 L/min） can also generate a larger effective plasma reaction zone with a longer arc length for chemical reactions. Two different motion patterns can be clearly observed in the N2 and air RGA plasmas. The time-resolved arc voltage signals show that three different arc dynamic modes, the arc restrike mode, takeover mode, and combined modes, can be clearly identified in the RGA plasmas. The occurrence of different motion and arc dynamic modes is strongly dependent on the composition of the working gas and gas flow rate.

Rolling element bearing instantaneous rotational frequency estimation based on EMD soft-thresholding denoising and instantaneous fault characteristic frequency

The accurate estimation of the rolling element bearing instantaneous rotational frequency(IRF) is the key capability of the order tracking method based on time-frequency analysis. The rolling element bearing IRF can be accurately estimated according to the instantaneous fault characteristic frequency(IFCF). However, in an environment with a low signal-to-noise ratio(SNR), e.g., an incipient fault or function at a low speed, the signal contains strong background noise that seriously affects the effectiveness of the aforementioned method. An algorithm of signal preprocessing based on empirical mode decomposition(EMD) and wavelet shrinkage was proposed in this work. Compared with EMD denoising by the cross-correlation coefficient and kurtosis(CCK) criterion, the method of EMD soft-thresholding(ST) denoising can ensure the integrity of the signal, improve the SNR, and highlight fault features. The effectiveness of the algorithm for rolling element bearing IRF estimation by EMD ST denoising and the IFCF was validated by both simulated and experimental bearing vibration signals at a low SNR.

Mechanism of principal stress rotation and deformation failure behavior induced by excavation in roadways

The failure modes of rock after roadway excavation are diverse and complex.A comprehensive investigation of the internal stress field and the rotation behavior of the stress axis in roadways is essential for elucidating the mechanism of roadway failure.This study aimed to examine the spatial relationship between roadways and stress fields.The law of stress axis rotation under three-dimensional(3D)stress has been extensively studied.A stress model of roadways in the spatial stress field was established,and the far-field stress state at different spatial positions of the roadways was analyzed.A mechanical model of roadways under a 3D stress state was established using far-field stress solutions as boundary conditions.The distribution of principal stressesσ1,σ2 andσ3 around the roadways and the variation of the stress principal axis were solved.It was found that the stability boundary of the stress principal axis exhibits hysteresis when compared with that of the principal stress magnitudes.A numerical analysis model for spatial roadways was established to validate the distribution of principal stress and the mechanism of principal axis rotation.Research has demonstrated that the stress axis undergoes varying degrees of spatial rotation in different orientations and radial depths.Based on the distribution of principal stress and the rotation law of the stress principal axis,the entire evolution mechanism of the two stress adjustments to form the final failure form after roadway excavation has been revealed.The on-site detection results also corroborate the findings presented in this paper.The results provide a basis for the analysis of the failure mechanism under a 3D stress state.

Analysis and Modeling of Wangqing Oil Shale Drying Characteristics in a Novel Fluidized Bed Dryer with Asynchronous Rotating Air Distributor

In order to replace the conventional distributor, a novel asynchronous rotating air distributor, which can optimize the drying ability of fluidized bed and strengthen the drying performance of oil shale particles, is creatively designed in this study. The rotating speed of the asynchronous rotating air distributor with an embedded center disk and an encircling disk is regulated to achieve the different air supply conditions. The impacts of different drying conditions on the drying characteristic of Wangqing oil shale particles are studied with the help of electronic scales. The dynamics of experimental data is analyzed with 9 common drying models. The results indicate that the particles distribution in fluidized bed can be improved and the drying time can be reduced by decreasing the rotating speed of the embedded center disk and increasing the rotating speed of the encircling disk. The drying process of oil shale particles involves a rising drying rate period, a constant drying rate period and a falling drying rate period. Regulating the air distributor rotating speed reasonably will accelerate the shift of particles from the rising drying rate period to the falling drying rate period directly. The two-term model fits properly the oil shale particles drying simulation among 9 drying models at different air supply conditions. Yet the air absorbed in the particles' pores is diffused along with the moisture evaporation, and a small amount of moisture remains on the wall of fluidized bed in each experiment, thus, the values of drying simulation are less than the experimental values.

Experimental study of rotating wind turbine breakdown characteristics in large scale air gaps

When a wind turbine is struck by lightning,its blades are usually rotating.The effect of blade rotation on a turbine＇s ability to trigger a lightning strike is unclear.Therefore,an arching electrode was used in a wind turbine lightning discharge test to investigate the difference in lightning triggering ability when blades are rotating and stationary.A negative polarity switching waveform of 250/2500 μs was applied to the arching electrode and the up-and-down method was used to calculate the 50%discharge voltage.Lightning discharge tests of a 1：30 scale wind turbine model with 2,4,and 6 m air gaps were performed and the discharge process was observed.The experimental results demonstrated that when a 2 m air gap was used,the breakdown voltage increased as the blade speed was increased,but when the gap length was 4 m or longer,the trend was reversed and the breakdown voltage decreased.The analysis revealed that the rotation of the blades changes the charge distribution in the blade-tip region,promotes upward leader development on the blade tip,and decreases the breakdown voltage.Thus,the blade rotation of a wind turbine increases its ability to trigger lightning strikes.

Surface characteristics of rapidly solidified nickel-based superalloy pow-ders prepared by PREP

The surface microstructure and the surface segregation of FGH 95 nickel-basedsuperalloy powders prepared through plasma rotating electrode processing (PREP) have beeninvestigated by using SEM and AES. The results indicate that the surface microstructure of powderschanges from dendrite into cellular stricture as the particle size of powders decrease, and thepredominant precipitates solidified on the particle surfaces were identified as MC' type carbidesenriched with Nb and Ti. It was also indicated that along with the depth of particle surfaces, thesegregation layer of S, C and O elements are thick, and that of Ti, Cr elements are thin for largesire powders while they are in reverse for median size particles.

An improved computation scheme of strapdown inertial navigation system using rotation technique

To improve the accuracy of strapdown inertial navigation system(SINS) for long term applications,the rotation technique is employed to modulate the errors of the inertial sensors into periodically varied signals,and,as a result,to suppress the divergence of SINS errors.However,the errors of rotation platform will be introduced into SINS and might affect the final navigation accuracy.Considering the disadvantages of the conventional navigation computation scheme,an improved computation scheme of the SINS using rotation technique is proposed which can reduce the effects of the rotation platform errors.And,the error characteristics of the SINS with this navigation computation scheme are analyzed.Theoretical analysis,simulations and real test results show that the proposed navigation computation scheme outperforms the conventional navigation computation scheme,meanwhile reduces the requirement to the measurement accuracy of rotation angles.

Current–voltage characteristics of hydrogen DC plasma torches with different sizes in an external axial magnetic field

Current-voltage （l-V） characteristics of hydrogen DC plasma torches with different sizes in an external axial magnetic field under atmospheric pressure are reported. Three anodes with different diameters are adopted in a 50-kW torch： 25 mm, 30 mm, and 35 nun, respectively. Two different diameters of anodes, that is, 100 mm and 130 mm, are adopted in a 1-MW plasma torch. The arc voltage shows a negative trend with the increase of arc current under the operating regimes. On the contrary, arc voltage shows a positive trend as the flow rate of carder gas increases, and a similar trend is found with increasing the external magnetic flux density. A similarity formula is constructed to correlate the experimental data of the torches mentioned above. Linear fitting shows that the Pearson correlation coefficient is 0.9958.

Analysis of the Flow Field Characteristics Associated with the Dynamic Rock Breaking Process Induced by a Multi-Hole Combined External Rotary Bit

The characteristics of the flow field associated with a multi-hole combined external rotary bit have been studied by means of numerical simulation in the framework of an RNG k-εturbulence model,and compared with the results of dedicated rock breaking drilling experiments.The numerical results show that the nozzle velocity and dynamic pressure of the nozzle decrease with an increase in the jet distance,and the axial velocity of the nozzle decays regularly with an increase in the dimensionless jet distance.Moreover,the axial velocity related to the nozzle with inclination angle 20°and 30°can produce a higher hole depth,while the radial velocity of the nozzle with 60°inclination can enlarge the hole diameter.The outcomes of the CFD simulations are consistent with the actual dynamic rock breaking and pore forming process,which lends credence to the present results and indicates that they could be used as a reference for the future optimization of systems based on the multi-hole combined external rotary bit technology.

Effects of Direct Sowing under Mulch-Based Cropping System (DMC) on Cotton and Maize Yield and Chemical Characteristics of Ferruginous Soil (Lixisoil) in the South Sudan Area of Burkina Faso

To better understand the effects of direct sowing under mulch-based cropping system (DMC) in Burkina Faso’s cotton production systems, randomized blocks of Fisher experimental design were implemented at Farako-Ba research station from 2010 to 2019. The study was conducted on lixisoil to evaluate DMC effects on biomass production, crops yields and soil chemical properties in a maize and cotton rotation system associated with cover crop. Conventional tillage and direct seeding without cover crop were compared to DMC under B. ruziziensis (GERM. & EVRARD), DMC under B. ruziziensis + M. cochinchinensis mulch and DMC under C. juncea (L.) mulch used in association with maize. Biomass production, crop yields and soil chemistry were evaluated. Results showed that over 10 years, no-till with or without a cover crop provided cotton seed and maize yields that were statistically equivalent to the tillage commonly practiced by farmers. Cover crop has allowed increasing the biomass production compared to Conventional Tillage and Direct Seeding. Maize yield has not varied significantly with the cover crop. After 10 years of maize and cotton rotation, the improvement raised from +27% to +38% for organic matter and from +15% to +29% for nitrogen with DMC including legumes such as M. cochinchinensis and C. juncea compared to Conventional Tillage on 0 - 5 cm depth. No significant differences were found on soil pH like P2O5 and K2O content. Although DMC with C. juncea used as cover crop did not provide the best biomass production, it contributes to increase nitrogen and organic matter and presents better mineral balances in 10 years of rotation. The 5 - 10 cm and 10 - 20 cm were little influenced by DMC systems.

Quality Characteristics and FTIR Research of Amorphophallus konjac K. Koch Cultivated under Forest

[Objectives]This study aimed to evaluate the quality characteristics of Amorphophallus konjac K.Koch and study the tubers of A.konjac K.Koch by infrared spectroscopy and second derivative method.[Methods]Referring to industrial standards of China for agriculture and related documents,the quality characteristics of A.konjac K.Koch were determined;and using potassium bromide tableting method and Fourier transform infrared spectroscopy,the infrared spectrum and second derivative spectrum of A.konjac K.Koch were studied.[Results]The drying rate,total ash content,acid-insoluble ash content,water extract content,ethanol extract content and crude polysaccharide content of A.konjac K.Koch were above 14.00%,4.57%-11.78%,0.04%-4.87%,26.31%-36.98%,2.20%-7.95%and 40.25%-61.18%,respectively.The infrared spectra of A.konjac K.Koch of different origins were relatively close,and the differences were mainly in peak intensity.The peaks at 1642,1322,1241,1154,1022,863,770 and 576 cm-1 were the main specific peaks.The main component was konjac glucomannan.[Conclusions]FTIR technology is simple and quick,and is suitable for quality control and sample identification of A.konjac K.Koch.This provides a scientific basis for the quality control and comprehensive utilization of A.konjac K.Koch cultivated under forest.

颈椎定点旋转手法在体生物力学量化及影响因素分析

背景:颈椎定点旋转手法属于技术要求较高的力学操作,但目前其生物力学还缺少相关量化数据;且颈椎定点旋转手法的影响因素研究包括了众多参数并且存在差异性,需要进一步对其影响因素进行分析,以完善其相关数据。目的:量化颈椎定点旋转手法在体生物力学参数,探讨各生物力学参数之间的相关性,及研究对象个体特征差异对手法力学参数的影响。方法:选取35例颈椎病患者为测试对象,均为广西中医药大学第一附属医院仁爱分院骨伤科门诊就诊者。术者佩戴穿戴式力学测量手套采集手法力学参数,包括拇指预加载力、拇指最大推力、掌心预加载力、掌心旋扳力和掌心旋扳最大作用力。并采集患者个人特征参数,包括年龄、身高、体质量和颈围。对手法操作过程中的关键力学参数进行特征分析及不同个体特征进行量化,对力学指标参数进行Spearman相关性分析;分析不同个体特征参数对生物力学可能存在的影响。结果与结论:(1)双侧力学参数相比,左侧操作与右侧操作无显著差异性(P>0.05)。(2)拇指预加载力均值为(7.21±1.19)N、拇指最大推力均值为(28.40±4.48)N、掌心预加载力均值为(5.67±2.49)N、掌心旋扳力均值为(10.90±5.11)N、掌心旋扳最大作用力均值为(16.00±7.27)N。(3)掌心预加载力和掌心旋扳力存在显著正相关(Rs=0.812,P<0.01);掌心预加载力和掌心旋扳最大作用力存在显著正相关(Rs=0.773,P<0.01);掌心旋扳力和掌心旋扳最大作用力存在显著正相关(Rs=0.939,P<0.01)。(4)患者体质量与拇指预加载力、掌心预加载力、掌心旋扳力及掌心旋扳最大作用力之间存在显著正相关(P<0.05)。(5)结果证实,颈椎定点旋转手法治疗颈椎病操作中生物力学有一定的标准量值。该手法左右侧操作无显著差异性,具有较好的一致性和可重复性。掌心预加载力、掌心旋扳力及掌心旋扳最大作用力3种力之间存在一致性和协调性,对于治疗效果的贡献是相近的。患者的体质量是影响颈椎定点旋转手法重要的因素。

Coupled flapwise-chordwise-axial-torsional dynamic responses of rotating pre-twisted and inclined cantilever beams subject to the base excitation

A rotating pre-twisted and inclined cantilever beam model (RPICBM) with the flapwise-chordwise-axial-torsional coupling is established with the Hamilton principle and the finite element (FE) method. The effectiveness of the model is verified via comparisons with the literatures and the FE models in ANSYS. The effects of the setting and pre-twisted angles on the dynamic responses of the RPICBM are analyzed. The results show that:(i) the increase in the setting or pre-twisted angle results in the increases in the first-order flapwise and torsional frequencies while the decrease in the first-order chordwise frequency under rotating conditions;(ii) a positive/negative setting angle leads to a positive/negative constant component, while a positive/negative pre-twisted angle leads to a negative/positive constant component;(iii) when the rotation speed is non-zero, the pre-twisted angle or non-zero setting angle will result in the coupled flapwise-chordwiseaxial- torsional vibration of the RPICBM under axial base excitation.

Laminar Flow in the Gap between Two Rotating Parallel Frictional Plates in Hydro-viscous Drive

The velocity, pressure and temperature distributions of the flow in the gap between hydro-viscous drive friction disks are the key parameters in the design of hydro-viscous drive and angular velocity controller. In the previous works dealing with the flow in the gap between disks in hydro-viscous drive, few authors considered the effect of Coriolis force on the flow. The object of this work is to investigate the flow with consideration of the effects of centrifugal force, Coriolis force and variable viscosity. A simplified mathematical model based on steady and laminar flow is presented. An approximate solution to the simplified mathematical model is obtained by using the iteration method assuming that the fluid viscosity remains constant. Then the model considering the effect of variable viscosity is solved by means of computational fluid dynamics code FLUENT. Numerical results of the flow are obtained. It is found that radial velocity profile diverges from the ideal parabolic curve due to inertial forces and tangential velocity profile is nonlinear due to Coriolis force, and pressure has two possible solution branches. In addition, it is found that variable viscosity plays an important role on pressure profiles which are significantly different from those of fluid with constant viscosity. The experimental device designed for this work consists of two disks, and one of them is fixed. Experimental pressure and temperature of the flow within test rig are obtained. It is shown that the trend of numerical results is in agreement with that of experimental ones. The research provides a theoretical foundation for hydro-viscous drive design.

Modeling of rotational supercavitating evaporator and the geometrical characteristics of supercavity within

In this paper,a rotational supercavitating evaporator(RSCE)was at first modeled by means of theoretical analysis approach.The geometrical characteristics of supercavity in the modeled RSCE were then studied through numerical simulations.The current research objectives consist in determination of shape of the supercavitator(which in the plane of rotation generates supercavity occupying the most volume between blades),and location of the area suitable for steam extraction by revealing the inner structure of supercavity.Analytical analysis was performed by solving empirical equations for the shape of RSCE,through which an evaluation of two-dimensional relative position of supercavity trailing edge for different shapes of the supercavitator has been realized.Numerical simulation was then carried out,by numerically solving the unsteady Navier-Stokes equations in their conservation form coupled with the Rayleigh-Plesset cavitation and Shear-Stress Transport turbulence models,for verification of the results obtained from empirical equations.Despite unreliable assumption of applicability of empirical equations we have confirmed similarity of the supercavity shapes obtained by both methods for the same RSCE.Therefore,the shape of supercavitator calculated by using empirical equations is acceptable,which provides a simple but reliable approach for design of RSCE.The inner structure of supercavity obtained by numerical simulation has indicated position and parameters for steam extraction openings for further numerical and experimental studies on the performance of RSCE.Practical application of steam or gas extraction is suggested for solving of some problems associated with cavitating pumping of cryogenic liquid.