期刊文献+
共找到545篇文章
< 1 2 28 >
每页显示 20 50 100
Leaching behavior of zinc and copper from zinc refinery residue and filtration performance of pulp under the hydrothermal process 被引量:1
1
作者 Lei Cao Ya-long Liao +2 位作者 Gong-chu Shi Yu Zhang Mu-yuan Guo 《International Journal of Minerals,Metallurgy and Materials》 SCIE EI CAS CSCD 2019年第1期21-32,共12页
This study aims to investigate the leaching behavior and filtration performance of zinc refinery residue under hydrothermal conditions. The relationships between the structure and morphology of silicon in the leaching... This study aims to investigate the leaching behavior and filtration performance of zinc refinery residue under hydrothermal conditions. The relationships between the structure and morphology of silicon in the leaching residue and the pulp filtration performance were explored by determining the pulp filtration speed, analyzing quantitatively the silicon content in the leachate, and characterizing the leaching residue structure. The results show that hydrothermal leaching induces the coagulation–hydrolysis of the silicon in solution, consequently altering the microstructure of the leaching residue, and that silicon oxygen tetrahedra([SiO_4]^(4-)) form the main skeleton structure of the residue. The results obtained also show that the leaching rates of zinc and copper are 98.1% and 98.7%, respectively, and that the filtration speed is 526.32 L/(m^2·h) under the conditions of sulfuric acid concentration of 140 g/L, leaching temperature of 160°C, leaching time of 3.0 h, oxygen partial pressure of 0.75 MPa, stirring speed of 600 r/min, and a liquid-to-solid ratio of 10 mL/g. 展开更多
关键词 ZINC REFINERY RESIDUE hydrothermal LEACHING filtration performance MESOPOROUS structure
下载PDF
Study on Filtration Performance of Silica/ Alumina Slurry in the Process of Recycling Mother Liquor of NaY Zeolite 被引量:1
2
作者 Guo Yaoqing Ma Yuelong Deng Jinghui(Research Institute of Petroleum Processing, Beijing 100083) 《China Petroleum Processing & Petrochemical Technology》 SCIE CAS 2004年第1期49-54,共6页
In order to recover the SiO_2 contained in the mother liquor in the course ofNaY zeolite synthesis to minimize pollution, the influence of various preparation conditions on thefiltering velocity of gel slurry was stud... In order to recover the SiO_2 contained in the mother liquor in the course ofNaY zeolite synthesis to minimize pollution, the influence of various preparation conditions on thefiltering velocity of gel slurry was studied using the SiO_2/Al_2O_3 gel recovered from the NaYmother liquor in the laboratory. The results of study had shown that at a SiO_2/Al_2O_3 ratio in thefeed equating to 9∶1 the SiO_2 recovery rate and Al_2O_3 utilization rate were high with a fasterflow velocity of the filtrate. The pH value of the system had great impact on the flow velocity offiltrate. Between the two methods for regulating the pH value, the one for formation ofsilica/alumina gel slurry by addition of sulfuric acid prior to adding aluminium sulfate in thesolution could secure a faster filtration velocity. The filtration velocity was decreased in tandemwith increasing SiO_2 concentration in mother liquor, meanwhile an increase in dry filter cakeyield. 展开更多
关键词 NaY zeolite mother liquor filtration performance Si/Al ratio GEL wasteutilization laboratory scale
下载PDF
Zeolite powder addition to improve the performance of submerged gravitation-filtration membrane bioreactor 被引量:8
3
作者 HE Sheng-bing XUE Gang KONG Hai-nan 《Journal of Environmental Sciences》 SCIE EI CAS CSCD 2006年第2期242-247,共6页
In this study, the effect of zeolite powder addition on submerged membrane bioreactor (SMBR) on membrane permeability, and the removals for COD, NH3-N, TN were investigated. Through the parallel operation of control... In this study, the effect of zeolite powder addition on submerged membrane bioreactor (SMBR) on membrane permeability, and the removals for COD, NH3-N, TN were investigated. Through the parallel operation of control and test systems, it was found that the zeolite powder addition could alleviate the ultra-filtration membrane fouling and enhance the membrane permeability. On the basis of experimental investigations, a concept of "protection coating layer" was proposed to illustrate the phenomenon of UF membrane fouling. In addition, the removal for COD in test system was more stable, a little higher compared to the control system. Due to the combination of nitrification and ion exchange, a more excellent removal for NH3-N in test system was obtained regardless of influent NH3-N loading rate. It was also found that a mean 25% higher TN removal took place in the test system, and ion exchange and simultaneous nitrification and de-nitrification were analyzed to be main factors. During the stable operation period, the SOURs of test zeolite powder added sludge and control activated sludge were measured to be 75 mgO2/(gMLVSS, h) and 24 mgO2/(gMLVSS, h) respectively, it meant that the zeolite powder addition could enhance the microorganism activity significantly. 展开更多
关键词 submerged gravitation-filtration membrane bioreactor performance zeolite powder membrane fouling microorganism activity
下载PDF
Evaluation of gas-liquid separation performance of natural gas filters 被引量:2
4
作者 Baisong Li Zhongli Ji Xue Yang 《Petroleum Science》 SCIE CAS CSCD 2009年第4期438-444,共7页
Fibrous filters are often used to remove contaminants including both dusts and liquid droplets from natural gas. This paper aims to evaluate the gas-liquid separation performance of three types of cartridge filters us... Fibrous filters are often used to remove contaminants including both dusts and liquid droplets from natural gas. This paper aims to evaluate the gas-liquid separation performance of three types of cartridge filters used in the West-East natural gas transmission project. The comparison of the original pressure drop of clean filters and the evolution of pressure drop as liquid droplets deposited in the filter media are described. The original pressure drops of these filters were similar but the pressure drops at a steady state were different. Fractional efficiency was used to study the separation performance of cartridge filters. Droplets at the outlet of the filters had small diameters, no more than 3 μm, but were very numerous. The effect of filtration velocity on gas-liquid separation performance was analyzed. Higher filtration velocity indicated better gas-liquid separation performance. Finally the quality factor related to pressure drop and filtration efficiency was applied to evaluate the gas-liquid separation performance. 展开更多
关键词 filtration natural gas gas-liquid separation fractional efficiency pressure drop
下载PDF
Effects of ZnCl2/H2O/C2H5OH Treatment on the Filter Paper Performance 被引量:2
5
作者 Lele Cao Lisheng Tang +1 位作者 Qing Li Wenbo Liu 《Paper And Biomaterials》 2019年第3期15-22,共8页
Bleached softwood kraft pulp (BSKP) fibers were pretreated in a 5 mol/L NaOH aqueous solution at 35℃ for 90 min. The ZnCl2/H2O/ C2H5OH was used to treat the pretreated BSKP fibers, filter papers were then prepared. I... Bleached softwood kraft pulp (BSKP) fibers were pretreated in a 5 mol/L NaOH aqueous solution at 35℃ for 90 min. The ZnCl2/H2O/ C2H5OH was used to treat the pretreated BSKP fibers, filter papers were then prepared. In the course of processing, the effects of various molar ratios of ZnCl2/H2O/C2H5OH on the filter paper performance were evaluated. SEMEDX was conducted to analyze the physical configuration of the filter papers. Moreover, FT-IR and XPS were performed to further characterize the BSKP, the pretreated BSKP and the filter paper fibers. The results indicated that the fibers treated by ZnCl2/H2O/C2H5OH were swollen and exhibited slight fibrillation, leading to a looser fiber structure and therefore, enhanced filter paper performance. Air permeability increased from 161.7 L/(m2·s) to 1450.4 L/(m2·s) for the filter papers when the molar ratio of ZnCl2/H2O/C2H5OH was 1:14:1. The optimum molar ratio of ZnCl2/H2O/C2H5OH was found to be 1:14:1, and no significant effect of ZnCl2/H2O/C2H5OH on fibers’ functional groups was detected. These results showed that filtration performance of filter papers was improved when treated with the ZnCl2/H2O/C2H5OH solution. 展开更多
关键词 BSKP fiber ZnCl2/H2O/C2H5OH filtration performance filter PAPERS
下载PDF
Low-Cost Stormwater Filtration System to Improve Urban Water Quality: The Case of Addis Ababa, Ethiopia
6
作者 Dagnachew Adugna Larissa Larsen +1 位作者 Brook Lemma Geremew Sahilu 《Journal of Water Resource and Protection》 2017年第6期692-705,共14页
Urbanization in developing countries often negatively impacts water re-sources by polluting surface waters. Addis Ababa, Ethiopia, is currently experiencing rapid urbanization accompanied by significant water shortage... Urbanization in developing countries often negatively impacts water re-sources by polluting surface waters. Addis Ababa, Ethiopia, is currently experiencing rapid urbanization accompanied by significant water shortages, unmanaged stormwater, and increasing river water pollution. To supplement the need for non-potable water and address stormwater runoff pollution, we constructed a low cost stormwater filtration system. The filtration system is comprised of a sedimentation area followed by three gravel grain sizes arranged horizontally from coarse to medium to fine filter media. We compared the quality of pretreatment water with post-treatment water by measuring physicochemical parameters, heavy metals and nutrients. We found that the filtration system reduced turbidity by 87%, TSS by 80%, Cu by 87% and Zn by 90%. Further, it positively increased the concentration of DO by 42%. However, the filtration system did not remove nitrates and nitrites. Implementing this system at outfalls in the rapidly expanding condominium housing areas can increase residents’ supply of non-potable water and reduce the amount of polluted stormwater entering nearby streams and rivers. 展开更多
关键词 Low COST STORMWATER filtration Addis Ababa Water Quality performance Test
下载PDF
Design and Experimental Analyses of Small-flow High-head Centrifugal-vortex Pump for Gas-Liquid Two-phase Mixture 被引量:28
7
作者 朱祖超 谢鹏 +2 位作者 偶国富 崔宝玲 李昳 《Chinese Journal of Chemical Engineering》 SCIE EI CAS CSCD 2008年第4期528-534,共7页
The design method of small-flow high-head centrifugal-vortex pump was presented. This pump, configured with inducer, complex-centrifugal impeller and open-vortex impeller, was put forward to deliver gas-liquid two-pha... The design method of small-flow high-head centrifugal-vortex pump was presented. This pump, configured with inducer, complex-centrifugal impeller and open-vortex impeller, was put forward to deliver gas-liquid two-phase mixture. An HTB-5/60 type sample pump was developed and tested on a closed-loop test rig. Experimental studies on performance and cavitation tests for gas-liquid two-phase mixture were carried out compared with pure-water experimental results. Also the effect of gas phase on pump was analyzed and discussed. The experimental results show that performance and cavitation characteristics of the sample purnp deteriorates progressively with increasing volume fraction of gas. When the total capacity Qm is between 4.5 m^3·h^-1 and 6 m^3·h^-1 and the gas flow rate qg below 0.66 m^3·h^-1, or qg/Qm is lower than 15%, the characteristic curves are approximately parallel to those in pure water test, but the performance deteriorates sharply until an abrupt flow-cutting at a critical volume fraction of gas. This pump is found suitable for transporting gas-liquid two-phase mixture when working around rated capacity of 5 m^3·h^-1 with qglQm below 15%. 展开更多
关键词 centrifugal-vortex pump gas-liquid two-phase flow performance and cavitation test
下载PDF
Magnetic filtration with magnetized granular beds:Basic principles and filter performance 被引量:1
8
作者 Teymuraz Abbasov 《China Particuology》 SCIE EI CAS CSCD 2007年第1期71-83,共13页
This study is devoted to the explanation of different characteristics of magnetic filtration and the way these characteristics affect the important filtration parameters. Magnetic fields in pores and the force effect ... This study is devoted to the explanation of different characteristics of magnetic filtration and the way these characteristics affect the important filtration parameters. Magnetic fields in pores and the force effect of these fields on magnetic particles and the magnetization properties of packed beds composed of ferromagnetic spheres and metal chips are evaluated. The profile of accumulation and capture regions of the particles, the variation of the fluid velocity in these regions and analytic expressions of particle capture radius are presented. The effects of filtration regime parameters on magnetic filter performance were investigated. An analytical expression has been obtained for the dependence of the logarithmic efficiency coefficient on filtration velocity, the geometry of filter elements, the particle size and other parameters of filtration. The stationary and non-stationary equations of the magnetic filtration processes are given. An expression of magnetic filter performance is shown with dimensionless parameters obtained from the filtration system. These relations are useful for calculations in engineering practice, including the design of magnetic filters, provision of suggestions on construction, and optimization and control of filter operation. 展开更多
关键词 Magnetic filtration Magnetized beds Particle filtration velocity Filter performance Capture radius
原文传递
超低阻呼吸防护用聚乳酸纳米纤维膜制备及长效过滤性能 被引量:2
9
作者 朱金佗 梁琛裕 +3 位作者 朱桂英 王存民 徐欢 王亮 《煤炭学报》 EI CAS CSCD 北大核心 2024年第4期1952-1963,共12页
长期暴露于大气环境中高浓度的细颗粒物(PM_(2.5))会对人类的长期健康效应产生消极影响,传统空气过滤材料难以兼顾高效、低阻的防护效果,且不可降解,不仅加剧全球塑料污染,还易产生更强的微塑料危害。为此,制备了一种具有空气滑移效应... 长期暴露于大气环境中高浓度的细颗粒物(PM_(2.5))会对人类的长期健康效应产生消极影响,传统空气过滤材料难以兼顾高效、低阻的防护效果,且不可降解,不仅加剧全球塑料污染,还易产生更强的微塑料危害。为此,制备了一种具有空气滑移效应、自供能且可生物降解的纳米纤维膜,以保障长效、低阻呼吸防护。提出两步水热法制备平均粒径49.6 nm、易分散的BaTiO_(3)电介质,同时利用“静电纺丝-静电喷雾”法将BTO纳米颗粒(BTO NPs)原位嵌入PLA纤维膜,利用BTO NPs的摩擦电效应和尺寸效应同步调控纤维膜的过滤效率和空气阻力。通过控制喷雾悬浮液中BTO NPs的浓度,探讨其与PLA/BTO纤维膜电活性、过滤性能和力学性能之间的关系。微观表征和性能测试结果表明:PLA/BTO纤维膜具有优异的电活性、过滤性能及力学性能。PLA/BTO纤维膜表面电势可高达5.9 kV,介电常数达1.20 F/m,平均输出电压高达12.4 V;得益于增强的空气分子滑移效应和电活性,PLA/BTO10纤维膜在显著降低空气阻力(低至20 Pa)的同时,对PM_(0.3)过滤效率提升了7.78%~9.05%,对PM_(2.5)过滤效率提升了2.90%~13.19%,即使在85 L/min高测试流量下仍能保证高达97.25%的PM_(2.5)过滤效率;同时,PLA/BTO纤维膜拉伸强度增幅高达60%(拉伸强度22.5 MPa),断裂伸长率增幅高达68%(断裂伸长率25%),而断裂韧性最高可提升1.3倍(断裂韧性3.6 MJ/m^(3))。因此,提出的兼具长效、低阻过滤且可降解纤维膜在呼吸防护领域具有广阔的应用前景,也为缓解废弃口罩加剧的塑料污染现状提供了一种新思路。 展开更多
关键词 可降解 自供能 电活性 过滤性能 空气阻力
下载PDF
空气过滤用聚氨酯纳米纤维膜的制备及其性能 被引量:1
10
作者 李金超 梅硕 +2 位作者 杜雨佳 马骉 李虹 《现代纺织技术》 北大核心 2024年第5期18-22,共5页
为拓展静电纺纳米纤维在空气过滤领域中的应用,以聚氨酯(PU)为原料,加入不同种类的盐,采用静电纺丝法制备树枝状PU纳米纤维膜。利用扫描电镜(SEM)、接触角测试仪、红外光谱仪、自动滤料测试仪测试纳米纤维膜的微观结构、亲疏水性、化学... 为拓展静电纺纳米纤维在空气过滤领域中的应用,以聚氨酯(PU)为原料,加入不同种类的盐,采用静电纺丝法制备树枝状PU纳米纤维膜。利用扫描电镜(SEM)、接触角测试仪、红外光谱仪、自动滤料测试仪测试纳米纤维膜的微观结构、亲疏水性、化学结构和过滤性能。结果表明:在PU质量分数14%条件下,添加有机盐TBAC,纺丝电压35 kV时,制备的纳米纤维膜的树枝状分叉结构明显;TBAC的加入使纤维膜的接触角由99.1°减小到82.8°;分叉结构使纳米纤维膜的过滤性能显著提高,与纯PU纳米纤维膜相比,过滤效率从50.8%提高到93.6%,品质因子从0.009提高到0.073,可满足高效低阻空气过滤材料的需求。 展开更多
关键词 聚氨酯 静电纺丝 纳米纤维膜 空气过滤 过滤性能
下载PDF
基于PPR和NSGA-Ⅱ的泵前微压过滤器水力与过滤性能研究
11
作者 陶洪飞 李琦 +3 位作者 周洋 马合木江·艾合买提 李巧 姜有为 《灌溉排水学报》 CAS CSCD 2024年第5期30-37,78,共9页
【目的】探究泵前微压过滤器的性能。【方法】开展5组流量(2~8m^(3)/h)、5组含沙量(0.5~2.0g/L)、3组滤网过滤面积(1 105、1 582、2 060 cm^(2))和4组分水器型式(不加、1型、2型、3型)的物理模型试验,采用投影寻踪回归分析法(PPR)、多... 【目的】探究泵前微压过滤器的性能。【方法】开展5组流量(2~8m^(3)/h)、5组含沙量(0.5~2.0g/L)、3组滤网过滤面积(1 105、1 582、2 060 cm^(2))和4组分水器型式(不加、1型、2型、3型)的物理模型试验,采用投影寻踪回归分析法(PPR)、多目标遗传算法(NSGA-Ⅱ),建立水头损失、截沙质量和总过滤效率的预测模型,探究各指标的影响因素排序,确定泵前微压过滤器的最佳运行工况。【结果】影响泵前微压过滤器水头损失的因素排序为进水流量?含沙量?滤网过滤面积;影响截沙质量的因素排序为含沙量?滤网过滤面积?进水流量;影响总过滤效率的因素排序为滤网过滤面积?含沙量?进水流量;以相对误差≤10%作为判定标准,建立的截沙质量和总过滤效率PPR预测模型合格率为100%,模型精度较高,但水头损失PPR预测模型合格率仅为70%,模型不可靠。本试验范围下泵前微压过滤器的最佳运行工况为:含沙量2 g/L、进水流量7 m^(3)/h、滤网过滤面积2 060 cm^(2)。【结论】PPR预测模型对截沙质量和总过滤效率的预测精度较高,对水头损失的预测误差较大,在后期可用量纲分析与多元回归相结合预测水头损失、截沙质量和总过滤效率。 展开更多
关键词 过滤器 水头损失 模型 水力性能 过滤性能
下载PDF
聚己内酯/MgO复合纳米纤维膜的制备及其性能
12
作者 贾琳 董晓 +2 位作者 王西贤 张海霞 覃小红 《纺织学报》 EI CAS CSCD 北大核心 2024年第4期59-66,共8页
为制备集多种功能于一体的纳米纤维膜,将MgO纳米颗粒加入至可降解聚己内酯(PCL)溶液中,通过静电纺丝技术制备PCL/MgO复合纳米纤维膜,研究了其微观形态、结晶结构、过滤性能和抗菌性能等。结果表明:PCL/MgO复合纳米纤维的直径比纯PCL略... 为制备集多种功能于一体的纳米纤维膜,将MgO纳米颗粒加入至可降解聚己内酯(PCL)溶液中,通过静电纺丝技术制备PCL/MgO复合纳米纤维膜,研究了其微观形态、结晶结构、过滤性能和抗菌性能等。结果表明:PCL/MgO复合纳米纤维的直径比纯PCL略有增加,且纤维膜中MgO依然保持着结晶状态;与纯PCL纤维膜相比,PCL/MgO复合纳米纤维膜的透气率增加,水接触角增大,透湿率减小;PCL/MgO复合纳米纤维膜的过滤效率为97.57%~98.87%,紫外线防护系数均大于50,具有良好的过滤性能和优异的紫外线防护性能,其对大肠杆菌的抑菌率为73.78%~98.55%,对金黄色葡萄球菌的抑菌率为53.61%~97.56%;对大肠杆菌的抑菌率优于金黄色葡萄球菌是因为MgO纳米颗粒具有晶格缺陷,更易与带有负电荷的大肠杆菌形成较强的相互作用。 展开更多
关键词 MgO纳米颗粒 聚己内酯纳米纤维 静电纺丝 抗菌性能 过滤性能
下载PDF
熔体微分电纺PLA/PAAS纳米纤维空气滤膜的制备及高湿环境下的过滤性能
13
作者 谭晶 付宏岩 +3 位作者 杜长彪 兰天杰 李好义 杨卫民 《塑料》 CAS CSCD 北大核心 2024年第4期121-127,共7页
为解决高湿环境下,空气滤膜的过滤效率迅速降低的问题,采用聚丙烯酸钠(PAAS)熔融共混改性聚乳酸(PLA),并且,利用熔体微分静电纺丝方法制备了PLA/PAAS熔体电纺亲水纳米纤维滤膜(PLA/PAAS电纺滤膜),主要研究了PAAS含量变化与滤膜性能之间... 为解决高湿环境下,空气滤膜的过滤效率迅速降低的问题,采用聚丙烯酸钠(PAAS)熔融共混改性聚乳酸(PLA),并且,利用熔体微分静电纺丝方法制备了PLA/PAAS熔体电纺亲水纳米纤维滤膜(PLA/PAAS电纺滤膜),主要研究了PAAS含量变化与滤膜性能之间的关系及高湿环境下,PAAS材料对滤膜过滤性能的影响。结果表明,当PAAS的含量(质量分数ω)为3%时,克重为40 g/m^(2)的PLA/PAAS电纺滤膜平均直径及直径标准差最小,分别为0.97μm及0.245,过滤效率达到最佳,其值为97.37%,品质因子达到0.0353 Pa^(-1);在高湿环境下,放置48 h后,PLA/PAAS电纺滤膜的过滤效率为95.49%,过滤品质因子为0.0206 Pa^(-1),证明了PLA/PAAS电纺滤膜在高湿环境下长时间放置后,性能仍保持稳定。 展开更多
关键词 熔体静电纺丝 共混改性 亲水滤膜 过滤性能 高湿环境
下载PDF
氧化石墨烯界面调控纳滤膜制备及性能研究
14
作者 丰桂珍 方圳生 +2 位作者 胡小杰 张火梅 陈俊 《环境科学与技术》 CAS CSCD 北大核心 2024年第8期17-25,共9页
为提高传统聚酰胺纳滤膜渗透性能和抗污染性能,文章以聚砜(PSF)超滤膜为基材,以哌嗪、均苯三甲酰氯为水相和有机相单体,引入氧化石墨烯(GO)作为亲水改性材料,通过界面聚合法制备氧化石墨烯复合纳滤膜(GO-PA-PSF膜),研究GO占比对膜表面... 为提高传统聚酰胺纳滤膜渗透性能和抗污染性能,文章以聚砜(PSF)超滤膜为基材,以哌嗪、均苯三甲酰氯为水相和有机相单体,引入氧化石墨烯(GO)作为亲水改性材料,通过界面聚合法制备氧化石墨烯复合纳滤膜(GO-PA-PSF膜),研究GO占比对膜表面形貌、化学结构及分离性能的影响。结果表明,当GO质量分数为0.01%时,GO-PA-PSF膜表面开始出现褶皱,膜表面粗糙度、亲水性和负电性增强,其渗透通量为50.47 L/(m^(2)·h),对Na_(2)SO_(4)的截留率为98.14%,在30 h脱盐试验中保持良好的稳定性,对3种模型污染物的抗污染性能有所提升。 展开更多
关键词 氧化石墨烯 界面聚合 聚酰胺纳滤膜 抗污染性能
下载PDF
改性碳纳米管接枝氯磺化间位芳纶纳米纤维膜的制备及性能研究
15
作者 柳静献 王靓 +3 位作者 孙立 田新娇 顾利定 贾瑞文 《安全与环境学报》 CAS CSCD 北大核心 2024年第3期1018-1026,共9页
将多壁碳纳米管(Multi-Walled Carbon Nanotubes,MWCNTs)与间位芳纶(Meta-Aramid,PMIA)进行复合有利于增强PMIA力学性能,近年来已成为研究热点,但MWCNTs分散性差、结合力差还易脱落,限制了其应用。利用氨基改性碳纳米管(MWCNTs-NH_(2))... 将多壁碳纳米管(Multi-Walled Carbon Nanotubes,MWCNTs)与间位芳纶(Meta-Aramid,PMIA)进行复合有利于增强PMIA力学性能,近年来已成为研究热点,但MWCNTs分散性差、结合力差还易脱落,限制了其应用。利用氨基改性碳纳米管(MWCNTs-NH_(2)),同时将PMIA进行氯磺化改性(PMIA-SO_(2)Cl),使PMIA-SO_(2)Cl与MWCNTs-NH_(2)通过—SO_(2)Cl与—NH_(2)偶联在一起,并采用超声波辅助溶液共混的方法,制备MWCNTs-NH_(2)/PMIA-SO_(2)Cl悬浮液。采用静电纺丝法,制备MWCNTs-NH_(2)/PMIA-SO_(2)Cl纳米纤维膜。结果显示,PMIA-SO_(2)Cl与MWCNTs-NH_(2)的偶联作用明显增强了MWCNTs在PMIA基体中的稳定性,与改性前相比,改性后悬浮液中MWCNTs分散更均匀,平均粒径更小。与MWCNTs/PMIA及MWCNTs-COOH/PMIA相比,改性后MWCNTs-NH_(2)/PMIA-SO_(2)Cl纳米纤维膜的力学性能与过滤性能均显著提高。 展开更多
关键词 安全卫生工程技术 氯磺化 表面修饰 静电纺丝 分散性 力学性能 过滤性能
下载PDF
改性二氧化硅封堵剂的制备及性能评价
16
作者 党海锋 刘刚 《山东化工》 CAS 2024年第9期48-50,共3页
为了降低水基钻井液滤液对储层的扰动,以丙烯酰胺、苯乙烯、乙烯基三甲氧基硅烷对纳米SiO_(2)进行表面改性,将柔性链聚合物接枝在纳米刚性SiO_(2)粒子表面,形成一种新型的有机-无机复合封堵剂。实验结果发现:该封堵剂提高了泥饼的致密... 为了降低水基钻井液滤液对储层的扰动,以丙烯酰胺、苯乙烯、乙烯基三甲氧基硅烷对纳米SiO_(2)进行表面改性,将柔性链聚合物接枝在纳米刚性SiO_(2)粒子表面,形成一种新型的有机-无机复合封堵剂。实验结果发现:该封堵剂提高了泥饼的致密性和封堵性能,并对岩心孔隙进行了有效封堵,有效抑制岩屑水化现象,为水基钻井液在低渗-致密储层开发过程中的应用提供技术支持。 展开更多
关键词 封堵剂 水基钻井液 封堵性能 纳米二氧化硅 滤失量
下载PDF
聚酰亚胺纳米纤维滤膜的制备及性能分析
17
作者 张海霞 张芳铖 贾琳 《河南工程学院学报(自然科学版)》 2024年第1期1-6,共6页
为探究亚胺化温度对聚酰亚胺(PI)纳米纤维性能的影响,将二胺单体4,4-二氨基二苯醚(ODA)和二酐单体均苯四甲酸酐(PMDA)溶于N,N-二甲基乙酰胺(DMAc)中,配制不同质量分数的聚酰胺酸(PAA)溶液,通过静电纺丝制成PAA纳米纤维滤膜,随后经过不... 为探究亚胺化温度对聚酰亚胺(PI)纳米纤维性能的影响,将二胺单体4,4-二氨基二苯醚(ODA)和二酐单体均苯四甲酸酐(PMDA)溶于N,N-二甲基乙酰胺(DMAc)中,配制不同质量分数的聚酰胺酸(PAA)溶液,通过静电纺丝制成PAA纳米纤维滤膜,随后经过不同温度亚胺化处理形成PI纳米纤维滤膜,研究滤膜的微观形态、过滤性能、透气性能和透湿性能等。结果表明:PAA溶液质量分数为30%时,其纳米纤维形态最好;亚胺化温度为200℃时,滤膜的过滤效率为95.86%,阻力压降为610.56 Pa,过滤性能平衡关系最好,此时最大强度为3.24MPa,透气率为98.19 mm/s;亚胺化温度为190℃时,水接触角为95.26°,润湿性能最好;透湿性能随着亚胺化温度的升高而降低。 展开更多
关键词 聚酰亚胺(PI) 亚胺化 静电纺丝 过滤性能 纳米纤维
下载PDF
硅酸盐/聚四氟乙烯/芳纶针刺毡复合滤袋的制备与性能
18
作者 柳静献 李亚霏 +1 位作者 吕超 程姣 《安全与环境学报》 CAS CSCD 北大核心 2024年第10期3889-3897,共9页
为了研发适用严苛高温工业条件下使用的袋式除尘器用针刺毡滤袋,利用乳液浸渍后处理工艺制备了具有热电/压电特性的硅酸盐(Polar Silicate,PS)粉体/聚四氟乙烯(Polytetrafluoroethylene,PTFE)涂层复合芳纶针刺毡滤袋,探究了PS粉体粒径... 为了研发适用严苛高温工业条件下使用的袋式除尘器用针刺毡滤袋,利用乳液浸渍后处理工艺制备了具有热电/压电特性的硅酸盐(Polar Silicate,PS)粉体/聚四氟乙烯(Polytetrafluoroethylene,PTFE)涂层复合芳纶针刺毡滤袋,探究了PS粉体粒径及附着浓度对复合滤袋捕集效率及阻力特性的影响规律,研究了复合滤袋机械性能,并通过扫描电镜(Scanning Electron Microscope,SEM)对复合滤袋进行了微观形貌分析。结果显示:PS粉体粒径对滤袋的阻力影响不大;PS粉体粒径在>21~32μm时,滤袋的过滤效率最大;最优附着浓度为6 mg/cm^(2)时,滤袋对0.3~1μm粒子的过滤效率提升幅度≥12.58百分点,滤袋的品质因数最高;PS粉体/PTFE/芳纶复合滤袋的耐磨性比芳纶针刺毡滤袋提升了19.86%,挺度提升了22.22%,纵向拉伸强度提升了14.07%。研究所制备的复合滤袋能够适应严苛的高温工业环境,可更好地控制工业排放的微细颗粒物。 展开更多
关键词 安全卫生工程技术 针刺毡滤袋 极性硅酸盐粉体 聚四氟乙烯涂层 过滤性能 机械性能
下载PDF
镓精矿氢氧化钠浸出过程镓的浸出行为 被引量:1
19
作者 廖文讯 廖彬 +4 位作者 王杰 彭明星 廖春发 刘付朋 张伟 《有色金属(冶炼部分)》 CAS 北大核心 2024年第1期73-79,97,共8页
从湿法炼锌工艺中得到的镓精矿是制备金属镓重要的中间产品,氢氧化钠浸出镓精矿制备电积前液是制备高品质金属镓的生产关键环节。通过研究氢氧化钠浸出镓精矿过程中添加剂的种类、添加剂用量、氢氧化钠浓度、浸出液固比、反应温度和浸... 从湿法炼锌工艺中得到的镓精矿是制备金属镓重要的中间产品,氢氧化钠浸出镓精矿制备电积前液是制备高品质金属镓的生产关键环节。通过研究氢氧化钠浸出镓精矿过程中添加剂的种类、添加剂用量、氢氧化钠浓度、浸出液固比、反应温度和浸出时间等工艺参数,分析了各工艺参数在镓精矿浸出过程中对Ga、Al的浸出率及浸出滤液过滤性能的影响。结果表明,在添加剂CaO 15%、NaOH浓度3 mol/L、液固比L/S=10、反应温度80℃、浸出时间120 min的最优条件下,Ga的浸出率为98.15%,Al的浸出率为53.01%,浸出滤液过滤速度为108.88 mL/min,添加剂CaO在反应过程中生成的铝酸钙作为滤饼支撑骨架,有效改善了浸出滤液的过滤性能。 展开更多
关键词 镓精矿 过滤性能 氢氧化钠 浸出
下载PDF
流量与含沙量对浮筒网式旋转过滤器水力性能与过滤性能的影响
20
作者 喜炜 靳桢 +1 位作者 李琦 陶洪飞 《节水灌溉》 北大核心 2024年第5期46-51,共6页
过滤器是保障微灌系统正常运行的核心设备,而水头损失与过滤效率是评价其性能的2个关键指标。为探明泵前过滤器—浮筒网式旋转过滤器的水力性能和过滤性能,采用方差分析、极差分析、主效应多重比较法对比分析了浮筒网式旋转过滤器在滤... 过滤器是保障微灌系统正常运行的核心设备,而水头损失与过滤效率是评价其性能的2个关键指标。为探明泵前过滤器—浮筒网式旋转过滤器的水力性能和过滤性能,采用方差分析、极差分析、主效应多重比较法对比分析了浮筒网式旋转过滤器在滤网孔径为0.150 mm时,5种不同含沙量、5种不同流量下的水头损失与过滤效率,并确定了试验条件下的最优工况。结果表明:对水头损失而言,流量比含沙量影响大;对过滤效率而言,含沙量的影响更大,且水头损失与过滤效率均随含沙量与流量的增大而增大;最优工况为流量930 L/h、含沙量2.0 g/L,此工况下对应的水头损失为0.281 m,过滤效率为84.01%,可以保证在有良好的过滤效率的同时具有较小的水头损失,从而实现节能减排,高效灌溉的目的。 展开更多
关键词 泵前过滤器 水力性能 过滤性能 微灌系统
下载PDF
上一页 1 2 28 下一页 到第
使用帮助 返回顶部