EFFICIENCY ANALYSIS OF DOUBLE CRANK RING-PLATE-TYPE PIN-CYCLOIDAL GEAR PLANETARY DRIVE

From the general formula for calculating the efficiency of planetary geartrains, the efficiency of the double crank ring-plate-type pin-cycloidal gear planetary drive isderived. To prove the theory, an experimental study has been conducted. The tested value of theefficiency of a sample set of the new-type drive in the experiment agrees with the calculated one.It shows that the new-type drive is of not merely high bearing capacity, but also quite highefficiency.

ANALYSIS OF TRANSMISSION CHARACTERISTICS OF COSINE GEAR DRIVE

Based on the mathematical model of a novel cosine gear drive, a few characteristics, such as the contact ratio, the sliding coefficient, and the contact and bending stresses, of this drive are analyzed. A comparison study of these characteristics with the involute gear drive is also carried out. The influences of design parameters including the number of teeth and the pressure angle on the contact and bending stresses are studied. The following conclusions are achieved： the contact ratio of the cosine gear drive is about 1.2 to 1.3, which is reduced by about 20% in comparison with that of the involute gear drive. The sliding coefficient of the cosine gear drive is smaller than that of the involute gear drive. The contact and bending stresses of the cosine gear drive are lower than those of the involute gear drive. The contact and bending stresses decrease with the growth of the number of teeth and the pressure angle.

Influence Predictions of Contact Effects on Mesh Stiffness of Face Gear Drives with Spur Gear

Mesh stiffness is one of important base parameters of face gear dynamic studies.However,a calculation solution of mesh stiffness of face gear drives is not to be constructed due to complex geometric flakes of face gear teeth.Thus,a calculation solution of mesh stiffness of face gear drives with a spur gear,which is based on the proposed equivalent face gear teeth and Ishikawa model,is constructed,and the influence of contact effects on mesh stiffness of face gear drives is investigated.The results indicate the mesh stiffness of face gear drives is sensitive to contact effects under heavy loaded operating conditions,specially.These contributions will benefit to improve dynamic studies of face gear drives.

Influence of Friction Drive Lift Gears Construction on the Length of Braking Distance

The friction drive elevators the influence of the braking distance has very high significance to meet certain safety regulations and comfort.During the emergency braking the delay for the system a frame and a cabin should be within the range from 0.2 to 9.81 m/s~2.However,there are no specialist literatures regarding the issues connected with emergency braking of elevating devices either.The results of the own empirical research work are presented regarding the influence of design changes on the working parameters of the friction drive elevator gears.ASG100,KB 160,PP16,PR2000UD and CHP2000 types of safety progressive gears are analyzed.ASG100,KB 160,PP16,PR2000UD type progressive gears are already produced by European manufacturers.CHP2000 type gears are established as the alternative option for the already existing solutions.The unique cam system has been used in the CHP 2000 gears.The cam leverage gives the chance to unblock,in a very easy way,the clamed gears after braking.Thus,it is a key aspect to perform laboratory tests over the braking process of a newly created solution.The proper value of the braking distance has a significant influence on the value of delay in terms of binding standards.The influence of loading on the effective braking distance and the value of the falling elevator cabin speed are analyzed and the results are presented.The results presented are interesting from lift devices operation and a new model of CHP 2000progressive gear point of view.

Parametric Analysis of the End Face Engagement Worm Gear

A novel specific type of worm drive, so-called end face engagement worm gear（EFEWD）, is originally presented to minimize or overcome the gear backlash. Different factors, including the three different types, contact curves, tooth profile, lubrication angle and the induced normal curvature are taken into account to investigate the meshing characteristics and create the profile of a novel specific type of worm drive through mathematical models and theoretical analysis. The tooth of the worm wheel is very specific with the sine-shaped tooth which is located at the alveolus of the worm and the tooth profile of a worm is generated by the meshing movement of the worm wheel with the sine-shaped tooth, but just the end face of the worm（with three different typical meshing types） is adapted to meshing, and therefore an extraordinary manufacturing methods is used to generate the profile of the end face engagement worm. The research results indicates that the bearing contacts of the generated conjugate hourglass worm gear set are in line contacts, with certain advantages of no-backlash, high precision and high operating efficiency over other gears and gear systems besides the end face engagement worm gear drive may improve bearing contact, reduce the level of transmission errors and lessen the sensitivity to errors of alignment. Also, the end face engagement worm can be easily made with superior meshing and lubrication performance compared with the conventional techniques. In particular, the meshing and lubrication performance of the end face engagement worm gear by using the end face to meshing can be increased over 10% and 7%, respectively. This investigate is expect to provide a new insight on the design of the future no-backlash worm drive for industry.

Model Based Incipient Fault Detection for Gear Drives

This paper presents the method of model based incipientfault detection for gear drives, this method is based on parity space method It can generate the robust residual that is maximally sensitive to the fault caused by the change of the parameters. The example of simulation shows the application of the method and the residual waves have different characteristics due to different parameter changes; one can detect and isolate the fault based on the different characteristics.

GEAR POSITION DECISION METHOD OF AUTOMATED MECHANICAL TRANSMISSION BASED ON FUZZY INFERENCE

A gear position decision method used in automated mechanical transmission is introduced. The algorithm of the mechod is composed of a driving environment and driver's intention estimator, the shift schedules suit for each typical driving environment and driver's intention situation, and an inference ligic to determine the most proper gear position for the present situation. The estimator identifies the driving environment and driver's intention features which are divided into some typical models. Based on the identified results, the algorithm works out the best gear position. It just simulates the course of driver's making gear position decision when driving a automobile with manual transmission. The test results show that the automated mechanical transmission with the method gives less unnecessary shifting and more proper gear position than common shift schedules.

Design of Damping Damping Design of New Boring Head Drive Structure

This paper takes the boring head of 20 roll mill as the research object,optimizes the vibration inside the boring head through a differential damping structure,and then conducts the 3 d model inside the boring head through SolidWorks,and checks the interference of the boring head model.Finally,Ansys workbench finite element analysis software is used to analyze and verify the vibration damping characteristics of the differential damping structure.

A NEW STATIC MECHANICS MODEL TO SOLVE CONTACT PROBLEMS IN MECHANICAL SYSTEMS

The coupling of the local contact problems between the components and the deformation of the components in the mechanical system were discovered.A series of coordinate systems have been founded to describe the mechanical system with the contact problems.The method of isolating the boundary of contact body from others has been used to describe the constraint between the contacting points.A more generalized static mechanics model of the mechanical system with the contact problems has been founded through the principle of virtual work.As an application,the model was used to study the multi_teeth engagement problems in the inner meshed planet gear systems.The stress distribution of contact gears was got.A test has verified that the static contact model and the computational method are right.