Based on the mathematical model of a novel cosine gear drive, a few characteristics, such as the contact ratio, the sliding coefficient, and the contact and bending stresses, of this drive are analyzed. A comparison s...Based on the mathematical model of a novel cosine gear drive, a few characteristics, such as the contact ratio, the sliding coefficient, and the contact and bending stresses, of this drive are analyzed. A comparison study of these characteristics with the involute gear drive is also carried out. The influences of design parameters including the number of teeth and the pressure angle on the contact and bending stresses are studied. The following conclusions are achieved： the contact ratio of the cosine gear drive is about 1.2 to 1.3, which is reduced by about 20% in comparison with that of the involute gear drive. The sliding coefficient of the cosine gear drive is smaller than that of the involute gear drive. The contact and bending stresses of the cosine gear drive are lower than those of the involute gear drive. The contact and bending stresses decrease with the growth of the number of teeth and the pressure angle.展开更多
From the general formula for calculating the efficiency of planetary geartrains, the efficiency of the double crank ring-plate-type pin-cycloidal gear planetary drive isderived. To prove the theory, an experimental st...From the general formula for calculating the efficiency of planetary geartrains, the efficiency of the double crank ring-plate-type pin-cycloidal gear planetary drive isderived. To prove the theory, an experimental study has been conducted. The tested value of theefficiency of a sample set of the new-type drive in the experiment agrees with the calculated one.It shows that the new-type drive is of not merely high bearing capacity, but also quite highefficiency.展开更多
We focused on the mathematical modeling and characteristics analysis for the nutation drive based on error parameters. The crown gear tooth profile equation was introduced according to the national standard double cir...We focused on the mathematical modeling and characteristics analysis for the nutation drive based on error parameters. The crown gear tooth profile equation was introduced according to the national standard double circular arc tooth profile and based on the equal tooth strength principle. The nutation drive meshing coordinate system was set up by introducing the cone vertex error, tilt error, nutation angle error and spiral angle error. The tooth profile equations of the double circular arc external and internal spiral bevel gears were further obtained based on the crown gear tooth profile equation concerning above mentioned error parameters. The influences of the nutation gear reducer tooth contact conditions were analyzed with the gear tilt error and axial misalignment error. Finally, the correctness of the theoretical analysis was verified by the contact spot test.展开更多
The structure of cylindrical tri-sine oscillating tooth gear drive is presented. Based on the space meshing theory, equations of meshing and tooth profile are established and its meshing theory is studied. Using Pro/E...The structure of cylindrical tri-sine oscillating tooth gear drive is presented. Based on the space meshing theory, equations of meshing and tooth profile are established and its meshing theory is studied. Using Pro/E, this system is modeled and simulated,which is compared with the above-established equations.展开更多
Mesh stiffness is one of important base parameters of face gear dynamic studies.However,a calculation solution of mesh stiffness of face gear drives is not to be constructed due to complex geometric flakes of face gea...Mesh stiffness is one of important base parameters of face gear dynamic studies.However,a calculation solution of mesh stiffness of face gear drives is not to be constructed due to complex geometric flakes of face gear teeth.Thus,a calculation solution of mesh stiffness of face gear drives with a spur gear,which is based on the proposed equivalent face gear teeth and Ishikawa model,is constructed,and the influence of contact effects on mesh stiffness of face gear drives is investigated.The results indicate the mesh stiffness of face gear drives is sensitive to contact effects under heavy loaded operating conditions,specially.These contributions will benefit to improve dynamic studies of face gear drives.展开更多
Torsional vibration of roller oscillating tooth gear drive (ROTGD) is studied in this paper. On the basis of conservation law for kinetic energy and potential energy, the mathematical expressions are developed which d...Torsional vibration of roller oscillating tooth gear drive (ROTGD) is studied in this paper. On the basis of conservation law for kinetic energy and potential energy, the mathematical expressions are developed which describe transformation of moment of inertia of inertial components into input shaft. Also, the formula is derived which expresses transformation of contact stiffness of elastic components into input shaft torsional stiffness. Besides, torsional vibration model of ROTGD is presented by using the transfer matrix method, and natural frequencies and vibration mode shapes are determined. Eventually, an example is given.展开更多
The friction drive elevators the influence of the braking distance has very high significance to meet certain safety regulations and comfort.During the emergency braking the delay for the system a frame and a cabin sh...The friction drive elevators the influence of the braking distance has very high significance to meet certain safety regulations and comfort.During the emergency braking the delay for the system a frame and a cabin should be within the range from 0.2 to 9.81 m/s~2.However,there are no specialist literatures regarding the issues connected with emergency braking of elevating devices either.The results of the own empirical research work are presented regarding the influence of design changes on the working parameters of the friction drive elevator gears.ASG100,KB 160,PP16,PR2000UD and CHP2000 types of safety progressive gears are analyzed.ASG100,KB 160,PP16,PR2000UD type progressive gears are already produced by European manufacturers.CHP2000 type gears are established as the alternative option for the already existing solutions.The unique cam system has been used in the CHP 2000 gears.The cam leverage gives the chance to unblock,in a very easy way,the clamed gears after braking.Thus,it is a key aspect to perform laboratory tests over the braking process of a newly created solution.The proper value of the braking distance has a significant influence on the value of delay in terms of binding standards.The influence of loading on the effective braking distance and the value of the falling elevator cabin speed are analyzed and the results are presented.The results presented are interesting from lift devices operation and a new model of CHP 2000progressive gear point of view.展开更多
In order to analyze the gear-rack reliability under the most serious limit loads which was the new-type transmission mechanism of aircraft slats,the gear-rack static strength under the single tooth meshing was analyze...In order to analyze the gear-rack reliability under the most serious limit loads which was the new-type transmission mechanism of aircraft slats,the gear-rack static strength under the single tooth meshing was analyzed based on the simulation and experiment. Then,it randomized the load of gear-rack based on the precise finite element analysis( FEA) model,and analyzed the static strength reliability of the gear-rack. Finally,the gear-rack under the most dangerous situation has not been destroyed and it also has a high reliability.展开更多
A direct digital design method （DDDM） of worm-gear drive is proposed. It is directly based on the simulation of manufacturing process and completely different from the conventional modeling method. The loaded tooth ...A direct digital design method （DDDM） of worm-gear drive is proposed. It is directly based on the simulation of manufacturing process and completely different from the conventional modeling method. The loaded tooth contact analysis （LTCA） method is analyzed, in which the advanced surface to surface searching technique is included. The influence of misalignment errors and contact deformations on contact zone and transmission error （TE） is discussed. Combined modification approach on worm tooth surface is presented. By means of DDDM and LTCA, it is very conven- ient to verify the effect of worm-gear drive＇s modification approach. The analysis results show that, the modification in profile direction reduces the sensitivity of worm-gear drive to misalignment errors and the modification in longitudinal direction decreases the TE. Thus the optimization design of worm-gear drive can be achieved prior to the actual manufacturing process.展开更多
A variable inertial damper, whose viscous damping coefficient can be adjusted by changing the gap between inertia wheel and motor spindle, is designed in servomechanism of zero-drive hobbing machine and is directly at...A variable inertial damper, whose viscous damping coefficient can be adjusted by changing the gap between inertia wheel and motor spindle, is designed in servomechanism of zero-drive hobbing machine and is directly attached on the motor spindle. The mathematical model of servo system with inertial damper is built. By using theoretical analysis and system simulation, it is demonstrated that the variable inertial damper with optimal damping coefficient and moment of inertia should lead to no resonance point in wider frequency range of exciting force. Therefore, its application in zero-drive hobbing machine makes this system not only achieve higher system stiffness to overcome load torque fluctuation, but also gain better stability.展开更多
Conventional fault tree and reliability analysis do not reflect the characteristics of basic events as non stationary and ergodic process. To overcome these drawbacks, theory of fuzzy sets is employed to run fault tre...Conventional fault tree and reliability analysis do not reflect the characteristics of basic events as non stationary and ergodic process. To overcome these drawbacks, theory of fuzzy sets is employed to run fault tree analysis(FTA) of roller oscillating tooth gear drive(ROTGD), the relative frequencies of basic events are considered as symmetrical normal fuzzy numbers, from the logical relationship between different events in the fault tree and fuzzy operators AND and OR, fuzzy probability of top event is solved. Finally, an example is given to demonstrate a real ROTGD system.展开更多
This paper presents the method of model based incipientfault detection for gear drives, this method is based on parity space method It can generate the robust residual that is maximally sensitive to the fault caused b...This paper presents the method of model based incipientfault detection for gear drives, this method is based on parity space method It can generate the robust residual that is maximally sensitive to the fault caused by the change of the parameters. The example of simulation shows the application of the method and the residual waves have different characteristics due to different parameter changes; one can detect and isolate the fault based on the different characteristics.展开更多
This paper takes the boring head of 20 roll mill as the research object,optimizes the vibration inside the boring head through a differential damping structure,and then conducts the 3 d model inside the boring head th...This paper takes the boring head of 20 roll mill as the research object,optimizes the vibration inside the boring head through a differential damping structure,and then conducts the 3 d model inside the boring head through SolidWorks,and checks the interference of the boring head model.Finally,Ansys workbench finite element analysis software is used to analyze and verify the vibration damping characteristics of the differential damping structure.展开更多
基金National Natural Science Foundation of China(No.50575071)Natural Science Foundation of Hunan Province,China(No.06JJl0008)+1 种基金S&T Programs of Hunan Province,China(No.2007FJ4047)Program for New Century Excellent Talents in University,China.
文摘Based on the mathematical model of a novel cosine gear drive, a few characteristics, such as the contact ratio, the sliding coefficient, and the contact and bending stresses, of this drive are analyzed. A comparison study of these characteristics with the involute gear drive is also carried out. The influences of design parameters including the number of teeth and the pressure angle on the contact and bending stresses are studied. The following conclusions are achieved： the contact ratio of the cosine gear drive is about 1.2 to 1.3, which is reduced by about 20% in comparison with that of the involute gear drive. The sliding coefficient of the cosine gear drive is smaller than that of the involute gear drive. The contact and bending stresses of the cosine gear drive are lower than those of the involute gear drive. The contact and bending stresses decrease with the growth of the number of teeth and the pressure angle.
基金This project is supported by National Natural Science Foundation of China (No.50175011).
文摘From the general formula for calculating the efficiency of planetary geartrains, the efficiency of the double crank ring-plate-type pin-cycloidal gear planetary drive isderived. To prove the theory, an experimental study has been conducted. The tested value of theefficiency of a sample set of the new-type drive in the experiment agrees with the calculated one.It shows that the new-type drive is of not merely high bearing capacity, but also quite highefficiency.
基金Funded by the National Natural Science Foundation of China(Grant No.51275092)the Program of Fujian Provincial Industrial Robot Basic Components Technology Research and Development Center(Grant No.2014H21010011)the Program of Fujian Provincial Collaborative Innovation Center for High-end Equipment Manufacturing
文摘We focused on the mathematical modeling and characteristics analysis for the nutation drive based on error parameters. The crown gear tooth profile equation was introduced according to the national standard double circular arc tooth profile and based on the equal tooth strength principle. The nutation drive meshing coordinate system was set up by introducing the cone vertex error, tilt error, nutation angle error and spiral angle error. The tooth profile equations of the double circular arc external and internal spiral bevel gears were further obtained based on the crown gear tooth profile equation concerning above mentioned error parameters. The influences of the nutation gear reducer tooth contact conditions were analyzed with the gear tilt error and axial misalignment error. Finally, the correctness of the theoretical analysis was verified by the contact spot test.
文摘The structure of cylindrical tri-sine oscillating tooth gear drive is presented. Based on the space meshing theory, equations of meshing and tooth profile are established and its meshing theory is studied. Using Pro/E, this system is modeled and simulated,which is compared with the above-established equations.
基金supported by the National Natural Science Foundations of China(Nos.51105194,51375226)the Fundamental Research Funds for the Central Universities(No.NS2015049)
文摘Mesh stiffness is one of important base parameters of face gear dynamic studies.However,a calculation solution of mesh stiffness of face gear drives is not to be constructed due to complex geometric flakes of face gear teeth.Thus,a calculation solution of mesh stiffness of face gear drives with a spur gear,which is based on the proposed equivalent face gear teeth and Ishikawa model,is constructed,and the influence of contact effects on mesh stiffness of face gear drives is investigated.The results indicate the mesh stiffness of face gear drives is sensitive to contact effects under heavy loaded operating conditions,specially.These contributions will benefit to improve dynamic studies of face gear drives.
文摘Torsional vibration of roller oscillating tooth gear drive (ROTGD) is studied in this paper. On the basis of conservation law for kinetic energy and potential energy, the mathematical expressions are developed which describe transformation of moment of inertia of inertial components into input shaft. Also, the formula is derived which expresses transformation of contact stiffness of elastic components into input shaft torsional stiffness. Besides, torsional vibration model of ROTGD is presented by using the transfer matrix method, and natural frequencies and vibration mode shapes are determined. Eventually, an example is given.
基金Nova Trading Company from Torun and Rywal-RHC Company from Lublin for the financial support owing to which it was possible to perform the research study and tests presented in the compilation.
文摘The friction drive elevators the influence of the braking distance has very high significance to meet certain safety regulations and comfort.During the emergency braking the delay for the system a frame and a cabin should be within the range from 0.2 to 9.81 m/s~2.However,there are no specialist literatures regarding the issues connected with emergency braking of elevating devices either.The results of the own empirical research work are presented regarding the influence of design changes on the working parameters of the friction drive elevator gears.ASG100,KB 160,PP16,PR2000UD and CHP2000 types of safety progressive gears are analyzed.ASG100,KB 160,PP16,PR2000UD type progressive gears are already produced by European manufacturers.CHP2000 type gears are established as the alternative option for the already existing solutions.The unique cam system has been used in the CHP 2000 gears.The cam leverage gives the chance to unblock,in a very easy way,the clamed gears after braking.Thus,it is a key aspect to perform laboratory tests over the braking process of a newly created solution.The proper value of the braking distance has a significant influence on the value of delay in terms of binding standards.The influence of loading on the effective braking distance and the value of the falling elevator cabin speed are analyzed and the results are presented.The results presented are interesting from lift devices operation and a new model of CHP 2000progressive gear point of view.
文摘In order to analyze the gear-rack reliability under the most serious limit loads which was the new-type transmission mechanism of aircraft slats,the gear-rack static strength under the single tooth meshing was analyzed based on the simulation and experiment. Then,it randomized the load of gear-rack based on the precise finite element analysis( FEA) model,and analyzed the static strength reliability of the gear-rack. Finally,the gear-rack under the most dangerous situation has not been destroyed and it also has a high reliability.
基金This project is supported by National Natural Science Foundation of China (No.E50575234).
文摘A direct digital design method （DDDM） of worm-gear drive is proposed. It is directly based on the simulation of manufacturing process and completely different from the conventional modeling method. The loaded tooth contact analysis （LTCA） method is analyzed, in which the advanced surface to surface searching technique is included. The influence of misalignment errors and contact deformations on contact zone and transmission error （TE） is discussed. Combined modification approach on worm tooth surface is presented. By means of DDDM and LTCA, it is very conven- ient to verify the effect of worm-gear drive＇s modification approach. The analysis results show that, the modification in profile direction reduces the sensitivity of worm-gear drive to misalignment errors and the modification in longitudinal direction decreases the TE. Thus the optimization design of worm-gear drive can be achieved prior to the actual manufacturing process.
基金This project is supported by Colleges and Universities Doctor Subject Special Science Foundation of China(No.20020611004)National Natural Science Foundation of China(No.50575232).
文摘A variable inertial damper, whose viscous damping coefficient can be adjusted by changing the gap between inertia wheel and motor spindle, is designed in servomechanism of zero-drive hobbing machine and is directly attached on the motor spindle. The mathematical model of servo system with inertial damper is built. By using theoretical analysis and system simulation, it is demonstrated that the variable inertial damper with optimal damping coefficient and moment of inertia should lead to no resonance point in wider frequency range of exciting force. Therefore, its application in zero-drive hobbing machine makes this system not only achieve higher system stiffness to overcome load torque fluctuation, but also gain better stability.
文摘Conventional fault tree and reliability analysis do not reflect the characteristics of basic events as non stationary and ergodic process. To overcome these drawbacks, theory of fuzzy sets is employed to run fault tree analysis(FTA) of roller oscillating tooth gear drive(ROTGD), the relative frequencies of basic events are considered as symmetrical normal fuzzy numbers, from the logical relationship between different events in the fault tree and fuzzy operators AND and OR, fuzzy probability of top event is solved. Finally, an example is given to demonstrate a real ROTGD system.
文摘This paper presents the method of model based incipientfault detection for gear drives, this method is based on parity space method It can generate the robust residual that is maximally sensitive to the fault caused by the change of the parameters. The example of simulation shows the application of the method and the residual waves have different characteristics due to different parameter changes; one can detect and isolate the fault based on the different characteristics.
基金2022 Liaoning Provincial Natural Science Foundation Plan(Yingkou Joint Fund),New Style Design and Optimization of Bore Head Drive Structure(Fund No.:2022-YKLH-17)In 2023,the key scientific research project of Yingkou Institute of Technology is the Design and Optimization of Smoke Drainage Pipe for New Mining Truck(Fund No.:ZDIL202306)2021 Natural Science Foundation ofLiaoning Province(Yingkou Joint Fund)Research on Dynamic Characteristics of Damped Vertical Shack(Fund No.:2021-YKLH-08).
文摘This paper takes the boring head of 20 roll mill as the research object,optimizes the vibration inside the boring head through a differential damping structure,and then conducts the 3 d model inside the boring head through SolidWorks,and checks the interference of the boring head model.Finally,Ansys workbench finite element analysis software is used to analyze and verify the vibration damping characteristics of the differential damping structure.
