Corrective Effect of the Angle of Incidence of the Magnetic Field Intensity on the Performance (Series and Shunt Resistances) of a Bifacial Silicon Solar Cell

This article presents a three-dimensional analysis of the impact of the angle of incidence of the magnetic field intensity on the electrical performance (series resistance, shunt resistance) of a bifacial polycrystalline silicon solar cell. The cell is illuminated simultaneously from both sides. The continuity equation for the excess minority carriers is solved at the emitter and at the depth of the base respectively. The analytical expressions for photocurrent density, photovoltage, series resistance and shunt resistance were deduced. Using these expressions, the values of the series and shunt resistances were extracted for different values of the angle of incidence of the magnetic field intensity. The study shows that as the angle of incidence increases, the slopes of the minority carrier density for the two modes of operation of the solar cell decrease. This is explained by a drop in the accumulation of carriers in the area close to the junction due to the fact that the Lorentz force is unable to drive the carriers towards the lateral surfaces due to the weak action of the magnetic field, which tends to cancel out as the incidence angle increases, and consequently a drop in the open circuit photovoltage. This, in turn, reduces the Lorentz force. These results predict that the p-n junction of the solar cell will not heat up. The study also showed a decrease in series resistance as the incidence angle of the magnetic field intensity increased from 0 rad to π/2 rad and an increase in shunt resistance as the incidence angle increased. His behaviour of the electrical parameters when the angle of incidence of the field from 0 rad to π/2 rad shows that the decreasing magnetic field vector tends to be collinear with the electron trajectory. This allows them to cross the junction and participate in the external current. The best orientation for the Lorentz force is zero, in which case the carriers can move easily towards the junction.

Determination of the Series Resistance of a Series Vertical-Junction Silicon (N+/P/P+) Solar Cell under Polychromatic Illumination and Magnetic Field: Effect of Optimum Thickness

By solving the magneto-transport equation for excess minority charge carriers in the base of the series vertical-junction silicon cell, the phenomenological parameters of the cell can be determined from the boundary conditions. Photocurrent density and photovoltage are determined for each value of applied magnetic field and corresponding optimum thickness, to establish the current-voltage characteristic (Jph(Sf, Sb, z, B, Hop)-Vph(Sf, Sb, z, B, Hop) of the silicon cell under polychromatic illumination. This study will make it possible to reduce the material used (by reducing the optimum thickness), which will help to lower prices. It will also enable us to reduce betting effects (lower series resistance), thereby boosting solar cell efficiency.

Research on geo-electrical resistivity observation system specially used for earthquake monitoring in China

This paper deals with the design and development of the observational system of geo-electrical resistivity on the basis of the demands for exploring the temporal variations of electrical properties of Earth media in the fixed points of the networks, which would be associated with the earthquake preparation. The observation system is characterized by the high accuracy in measurement, long term stability in operation and high level of rejection to the environmental interference. It consists of three main parts, configuration system measurement system, the calibration and inspection system.

Characterization and screening of cotton(Gossypium hirsutum L.)germplasm for leafhopper(Amrasca biguttula biguttula(Ishida))resistance

Background Cotton(Gossypium hirsutum L.)is one of the most significant fibre and cash crops and plays an important role in Indian industrial and agricultural economies.However,over the years quantity and quality have been hampered by the pest leafhopper.Leafhopper alone has been shown to cause yield losses of up to 40%.In this study,screening and evaluation were performed to identify and categorize 100 cotton genotypes along with 5 checks as resistant,moderately resistant,sensitive and highly sensitive to leafhoppers.Results A total of hundred genotypes were evaluated along with five checks for leafhopper resistance.Based on the screening results,a total of 19 genotypes were resistant to leafhoppers,which was on par with the findings of the check KC 3.The contents of total soluble sugar,total soluble protein,and total free amino acids were significantly positively correlated with the mean grade,whereas total phenols content and trichome density were significantly negatively correlated with the susceptibility grade.However,based on screening and biochemical analysis,the genotypes KC 2,JR-23,Samaru-26-T,D 4,TCH 1728,RS 253,and B-61-1862 exhibited high resistance to leafhopper.Conclusion According to the findings of this study,choosing genotypes with high total phenolics content together with high trichome density and low contents of total soluble sugar,total soluble protein,and free amino acids may aid in the development of resistant genotypes.

The action mechanism of the work done by the electric field force on moving charges to stimulate the emergence of carrier generation/recombination in a PN junction

It is discovered that the product of the current and the electric field in a PN junction should be regarded as the rate of work(power)done by the electric field force on moving charges(hole current and electron current),which was previously misinterpreted as solely a Joule heating effect.We clarify that it is exactly the work done by the electric field force on the moving charges to stimulate the emergence of non-equilibrium carriers,which triggers the novel physical phenomena.As regards to Joule heat,we point out that it should be calculated from Ohm’s law,rather than simply from the product of the current and the electric field.Based on this understanding,we conduct thorough discussion on the role of the electric field force in the process of carrier recombination and carrier generation.The thermal effects of carrier recombination and carrier generation followed are incorporated into the thermal equation of energy.The present study shows that the exothermic effect of carrier recombination leads to a temperature rise at the PN interface,while the endothermic effect of carrier generation causes a temperature reduction at the interface.These two opposite effects cause opposite heat flow directions in the PN junction under forward and backward bias voltages,highlighting the significance of managing device heating phenomena in design considerations.Therefore,this study possesses referential significance for the design and tuning on the performance of piezotronic devices.

Frost Resistance of Pervious Concrete Mixed with Waste Glass Powder

The contents of waste glass powder(WGP)(0%,10%,15%,20%,25%)and water-binder ratio(W/C)(0.24,0.26,0.28)were used as influencing factors,and the quality loss rate(Δm)and compressive strength loss rate(Δfc)were used as characterization parameters.The Ca/Si ratio and main element contents of C-S-H gels with different WGP content were investigated by energy dispersive spectrometry(EDS).The pore structure evolution characteristics of WGP composite cementing materials were investigated by low field nuclear magnetic resonance(NMR).UsingΔfc as the index of frost resistance degradation and Weibull function,the frost resistance degradation of glass doped pervious concrete(WGP-PC)was modeled.The results show that,with WGP,for the same number of cycles,Δm andΔfc decrease and increase with the increase of WGP.Under the same WGP content,Δm andΔfc decrease first and then increase with the increase of W/C.After 100 freeze-thaw cycles,the samples with WGP content of 20%and W/C of 0.26 have the best freeze-resistance.Microscopic tests show that with the increase of WGP content,the Ca/Si ratio of C-S-H gel decreases at first and then increases with the increase of WGP content.The extreme value of Ca/Si is 2.36 when WGP is added by 20%.The pore volume of hardened paste with 20%WGP content decreased by 18.6%compared with that of cement system without WGP.The overall compactness of the specimen was improved.On the basis of the test data,a life prediction model was established according to Weibull function.The experiment showed thatΔfc could be used as a durability degradation index,and the slope of the reliability curve became gentle after WGP was added,which reduced the damage degradation rate of PC.W/C was 0.26.It's about 5000 hours.

Analysis and Study on the Change of the Observed Geo-electric Field Data at Lhasa Geomagnetic Station before and after the Nepal MS8.1 Earthquake

In this paper,the main purpose is to analyze and research the characteristics of the geoelectric field observed data with a long time span and large amplitude abnormal change,at the Lhasa geomagnetic station( hereafter referred to as "Lhasa station "),before and after the Nepal M_S8. 1 strong earthquake,which occurred on April 25,2015. Based on the observation conditions,the observation system,and the observed data of Lhasa station preliminary discussed,the main characteristics of the abnormal change and evolution process are analyzed and studied,using the following two methods; the "synthesis energy accumulation"and the "power as MSA spectrum"analysis,from the two aspects of the"Time Domain"and"Frequency Domain. "The results show that the abnormal change of the geo-electric field observation of Lhasa station experienced a development stage following the process of "trend change- disturbance change- earthquake period-recovery period",and an evolution process of "low frequency change- high frequency change- smooth change- high frequency change ",before and after the Nepal M_S8. 1strong earthquake. Comprehensive analysis shows that the variation characteristics and evolution process of the geo-electric field at Lhasa station are basically consistent with the results of the relevant mechanism and phenomenon research. So far,this is valuable information with certain objectivity,which is typical and representative to reflect the whole process of the gestation, occurrence and complete development of such strongearthquakes.

Prevalence and Study of the Clonality of Extended-Spectrum Beta-Lactamase-Producing Klebsiella pneumoniae Strains in Neonatology at the University Hospitals of Abidjan by the Pulsed Field Gel Electrophoresis and the Quantitative Antibiogram

Background: ESBL-producing strains of Klebsiella pneumoniae, one of the main causes of nosocomial and hospital-acquired infections, are commonly associated with therapeutic impasses. Surveillance of these multidrug-resistant pathogens is a crucial tool for controlling and preventing infections. This surveillance involves the use of appropriate molecular and phenotypic typing techniques. The choice of techniques is based on criteria such as discriminatory power, intra- and inter-laboratory reproducibility, epidemiological concordance, ease of use and cost. The aim of our study was to identify clusters of Extended-Spectrum Beta-Lactamase-producing Klebsiella pneumoniae (ESBL-K. pneumoniae) strains circulating in neonatology using quantitative antibiogram (QA) and Pulsed Field Gel Electrophoresis (PFGE). Materials and Methods: This cross-sectional study included 55 K. pneumoniae strains isolated from a total of 513 samples. These various samples are taken from newborns, healthcare personnel, and the environment. K. pneumoniae identification followed standard bacteriological procedures and was confirmed using the Vitek® 2 (bioMérieux). The detection of the ESBL phenotype was performed using the synergy test. QA and PFGE were used to identify clonal relationships between the various strains isolated. Concordance between these two methods was assessed by calculating Cohen’s KAPPA coefficient and Simpson’s diversity index. Results: Among the 55 K. pneumoniae strains included in this study, 58.2% (32/55) were found to be Extended-Spectrum Beta-Lactamase (ESBL) producers. Most of these strains were isolated from neonatal samples (blood samples and rectal swabs). The quantitative antibiogram method applied to 28 out of the 32 ESBL-producing strains revealed that the isolates were grouped into 5 clusters. Pulsed Field Gel Electrophoresis performed on a total of 16 ESBL-producing strains showed the existence of four profiles. A perfect concordance was observed between the two methods. Conclusion: The results of this study highlighted the existence of clonal strains of various origins within neonatology units.

Forward modeling of marine DC resistivity method for a layered anisotropic earth

Since the ocean bottom is a sedimentary environment wherein stratification is well developed, the use of an anisotropic model is best for studying its geology. Beginning with Maxwell＇s equations for an anisotropic model, we introduce scalar potentials based on the divergence-free characteristic of the electric and magnetic （EM） fields. We then continue the EM fields down into the deep earth and upward into the seawater and couple them at the ocean bottom to the transmitting source. By studying both the DC apparent resistivity curves and their polar plots, we can resolve the anisotropy of the ocean bottom. Forward modeling of a high-resistivity thin layer in an anisotropic half-space demonstrates that the marine DC resistivity method in shallow water is very sensitive to the resistive reservoir but is not influenced by airwaves. As such, it is very suitable for oil and gas exploration in shallowwater areas but, to date, most modeling algorithms for studying marine DC resistivity are based on isotropic models. In this paper, we investigate one-dimensional anisotropic forward modeling for marine DC resistivity method, prove the algorithm to have high accuracy, and thus provide a theoretical basis for 2D and 3D forward modeling.

Improvement of Electrical Performance of SOI-LIGBT by Resistive Field Plate

The electrical performance including breakdown voltage and turn-off speed of SOI-LIGBT is improved by incorporating a resistive field plate (RFP) and a p-MOSFET.The p-MOSFET is controlled by a signal detected from a point of the RFP.During the turning-off of the IGBT,the p-MOSFET is turned on,which provides a channel for the excessive carriers to flow out of the drift region and prevents the carriers from being injected into the drift region.At the same time,the electric field affected by the RFP makes the excessive carriers flow through a wider region,which almost eliminates the second phase of the turning-off of the SOI-LIGBT caused by the substrate bias.Faster turn-off speed is achieved by above two factors.During the on state of the IGBT,the p-MOSFET is off,which leads to an on-state performance like normal one.At least,the increase of the breakdown voltage for 25% and the decrease of the turn-off time for 65% can be achieved by this structure as can be verified by the numerical simulation results.

Numerical simulation on temperature field for resistance spot welding of non-equal thickness stainless steel

An axisymmetric finite element model is developed to simulate the temperature field of resistant spot welding according to the process characters of nugget formation of non equal stainless steel sheets. A simulation method of the interaction of electrical and thermal factors is presented. The spot welding process of nugget formation is simulated using hard and soft welding technique norms. The heating characters of soft and hard norms determine the differences in the process of nugget formation and determine the finally shape and offset of nugget. Experimental verification shows that the model prediction agrees well with the practical.

Reconstruction of Current Density Distribution in Weld Area During Resistance Spot Welding of Aluminum Alloy Based on Magnetic Field

Magnetic flux density around the weld area was used to reconstruct the current density distribution during resistance spot welding(RSW) of aluminum alloy according to inverse problem theory. A current-magnetic field model was established and the conjugate gradient method was used to solve this model. The results showed that the current density was low at the center of nugget while high on the edge of nugget. Moreover, the welding time of 30ms—60 ms is a key period for nucleation. The current density distribution can reflect whether the weld nugget is formed or splashed, therefore it has the potential to monitor the weld quality of RSW.

CFD simulation of flow field and resistance in a 19-core tandem ceramic membrane module

CFD simulation of the permeation process of a 19-core tandem ceramic membrane module was established to investigate flow field and resistance and its change in permeate flux to the membrane element position and the channel of each membrane element.The results show that when the volume flow rate changes from26 m3·h-1 to 89 m3·h-1,the resistance of each part of the membrane module increases gradually.The increase in resistance loss in the membrane element is faster than the plates and the bell mouths.In a single ceramic membrane module,the maximum difference in flow rate of each membrane tube is 7.23%.In a single membrane tube,the outer ring channels 3–5,3–6,3–7,3–8 are relatively slow.The maximum mass flow deviation from the mean is 2.7%.This work helps to clarify the flow mechanism within the modules,optimize the structure of the equipment and provide a reliable basis for the improvement of industrial ceramic membrane modules.

Crystal orientation and corrosion resistance of CuNi10Fe1Mn alloy billet under rotating electromagnetic field

CuNi10Fe1Mn alloy billet under rotating electromagnetic field (REF) was characterized in this work. The change of the crystal orientation was first explored by X-ray diffraction (XRD) and scanning election microscope (SEM); the corrosion resistance was done by three electrodes system, and the natural sea water was used as corrosion medium. The results demonstrate that the strongest crystal orientation is transformed from crystal plane (200) to (111); moreover, the crystal plane (111) whose intensity is the strongest on the cross section and vertical section with REF causes the tubes be rolled easily, and the corrosion resistance of the billet is increasing with REF. As a result, properties of CuNi10Fe1Mn alloy tubes can be improved by REF.

Antibiotic-Resistant Bacterial Group in Field Soil Evaluated by a Newly Developed Method Based on Restriction Fragment Length Polymorphism Analysis

Spreading of antibiotic resistant bacteria into environment is becoming a major public health problem, implicating affair of the indirect transmission of antibiotic resistant bacteria to human through drinking water, or vegetables, or daily products. Until now, the risk of nosocomial infection of antibiotic resistant bacteria has mainly been evaluated using clinical isolates by phenotypic method. To evaluate a risk of community-acquired infection of antibiotic resistant bacteria, a new method has been developed based on PCR-RFLP without isolation. By comparing restriction fragment lengths of the 16S rDNA gene from bacterial mixture grown under antibiotic treatment to those simulated from the DNA sequence, bacterial taxonomies were elucidated using the method of Okuda and Watanabe [1] [2]. In this study, taxonomies of polymyxin B resistant bacteria group in field soils, paddy field with organic manure and upland field without organic manure were estimated without isolation. In the both field soils, the major bacteria grown under the antibiotic were B. cereus group, which had natural resistance to this antibiotic. In field applied with organic manure, Prevotella spp., and the other Cytophagales, which were suggested to be of feces origin and to acquire resistance to the antibiotic, were detected. When numbers of each bacterial group were roughly estimated by the most probable number method, B. cereus group was enumerated to be 3.30 × 106 MPN/g dry soil in paddy field soil and 1.32 × 106 MPN/g dry soil in upland filed. Prevotella spp. and the other Cytophagales in paddy field were enumerated to be 1.31 × 106 MPN, and 1.07 × 106 MPN·g-1 dry soil.

Experiment Research on Fouling Resistance Grey Forecast Model for Circulating Water in Electromagnetic Field

以自行设计的实验平台为基础，通过获得的不同频率电磁场作用下实验管的污垢热阻及水质参数，建立了电磁场作用下循环水污垢热阻的新陈代谢不等时距加权预测模型和拓灰色预测模型。利用实验数据分析了2种模型的预测精度，拓灰色预测模型较不等时距加权预测模型预测精度更高，计及实验不确定度，预测结果表明2种模型的预测精度均在92％以上，能较精确预测污垢热阻的变化趋势，适应水质参数及环境的变化，为建立多水质参数的数学模型及探索电磁抑垢机制提供参考。

A low specific on-resistance SOI LDMOS with a novel junction field plate

A low specific on-resistance SO1 LDMOS with a novel junction field plate （JFP） is proposed and investigated theo- retically. The most significant feature of the JFP LDMOS is a PP-N junction field plate instead of a metal field plate. The unique structure not only yields charge compensation between the JFP and the drift region, but also modulates the surface electric field. In addition, a trench gate extends to the buffed oxide layer （BOX） and thus widens the vertical conduction area. As a result, the breakdown voltage （BV） is improved and the specific on-resistance （Ron,sp） is decreased significantly. It is demonstrated that the BV of 306 V and the Ron,sp of 7.43 mΩ.cm2 are obtained for the JFP LDMOS. Compared with those of the conventional LDMOS with the same dimensional parameters, the BV is improved by 34.8%, and the Ron,sp is decreased by 56.6% simultaneously. The proposed JFP LDMOS exhibits significant superiority in terms of the trade-off between BV and Ron,sp. The novel JFP technique offers an alternative technique to achieve high blocking voltage and large current capacity for power devices.

Cosmic Ether, Possessing Electric-Tension and Magnetic-Resistance, Is the Unified Field for Physics

The paper presents the case that physics is already and effectively unified by the energetic tension field, ether. We identify this integrating power of ether first, by re-defining the action generating parameters of this energetic tension field as the electric-tension, , and the magnetic-resistance, μ0, while re-deriving the Maxwell’s wave equation in analogy with the mechanically stretched string, where the . Then, replacing by and m0 by , one can find that almost all working physics theories are being energized byand μ0. To complete the unification, we can now postulate that the particles are also freely propagating EM waves, but they are spatially localized as in-phase, close-looped (IP-CL) vortex-like propagation modes of ether. Because of their IP-CL mode structure, they have space-finite spatial structures and remain spatially stationary in the absence of any spatially influencing potential gradients (forces) in their vicinity. Particles’ harmonic phase driven interactions between quantum particles give birth to the appearance of wave-particle duality. There is no need for the confusing and unnecessary de Broglie’s Pilot Wave. The inertia to spatial motion of IP-CL modes automatically accommodates Newton’s laws of motion. The cosmic universality of Maxwellian wave velocity, and particles as IP-CL modes, jointly accommodate the two key postulates of special relativity without the need for unphysical four-dimensionality. The observable universe is represented only by its diverse oscillatory excited states. The stable and stationary Cosmic Ether keeps holding 100% of its energy all the time. We have proposed a one-way light pulse propagation experiment to directly validate the existence of ether, rather than approaching Michelson’s way of measuring the ether drag. We have identified a good number of examples of working theoretical expressions in terms of and μ0 and presented our critical views in physics thinking, belonging to Classical, Relativity, Quantum and Cosmology Physics.

Evaluation of host resistance and fungicide application as tools for the management of root rot of field pea caused by Aphanomyces euteiches

Aphanomyces root rot(ARR) of field pea(Pisum sativum), caused by Aphanomyces euteiches, can cause severe root damage, wilting, and large yield losses under wet soil conditions. To identify ways to manage this disease, the effect of A. euteiches inoculum density on field pea was studied under greenhouse and field conditions in 2015 and 2016. Increases in inoculum density reduced seedling emergence, root nodulation, and plant vigor, and resulted in increased root rot severity in both field and greenhouse tests. Seed treatments with the fungicides Apron Advance(thiabendazole + fludioxonil + metalaxyl) + Vibrance(difenoconazole + metalaxylM + sedaxane), INTEGO Solo(ethaboxam), BAS 516F(boscalid + pyraclostrobin), BAS 720F(metalaxyl + pyraclostrobin + fluxapyroxad), and BAS 516F + BAS 720F(3:1) were evaluated for their efficacy against ARR. All seed treatments except Apron Advance + Vibrance reduced root rot severity under controlled conditions. BAS 516F, BAS 720F and INTEGO Solo improved plant vigor and all treatments reduced seedling blight to varying degrees under greenhouse conditions, but not in the field. A collection of 22 pea genotypes was evaluated for resistance to root rot in field plot experiments. Line 00–2067 showed the least severe root rot symptoms,whereas ‘Spring D' showed the lowest reduction in yield. The results suggest that there may be an opportunity to combine partial host resistance and fungicidal seed treatments to adequately manage ARR of field pea.

Input signal design to estimate interwell connectivities in mature fields from the capacitance-resistance model

Interwell connectivities are fundamental parameters required to manage waterfloods in oil reservoirs. Data-driven models, such as the capacitance-resistance model （CRM）, are fast tools to estimate these parameters from time-correlations of input （injection rates） and output （production rates） signals. Noise and structure of the input time-series impose limits on the information that can be extracted from a given data-set. This work uses the CRM to study general prescriptions for the design of input signals that enhance the information content of injection/production data in the estimation of well-to-well interactions. Numerical schemes and general features of the optimal input signal strategy are derived for this problem.