In Mg-Ca alloys the grain refining mechanism,in particular regarding the role of nucleant substrates,remains the object of debates.Although native MgO is being recognised as a nucleating substrate accounting for grain...In Mg-Ca alloys the grain refining mechanism,in particular regarding the role of nucleant substrates,remains the object of debates.Although native MgO is being recognised as a nucleating substrate accounting for grain refinement of Mg alloys,the possible interactions of MgO with alloying elements that may alter the nucleation potency have not been elucidated yet.Herein,we design casting experiments of Mg-xCa alloys varied qualitatively in number density of native MgO,which are then comprehensively studied by advanced electron microscopy.The results show that grain refinement is enhanced as the particle number density of MgO increases.The native MgO particles are modified by interfacial layers due to the co-segregation of Ca and N solute atoms at the MgO/Mg interface.Using aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy,we reveal the nature of these Ca/N interfacial layers at the atomic scale.Irrespective of the crystallographic termination of MgO,Ca and N co-segregate at the MgO/Mg interface and occupy Mg and O sites,respectively,forming an interfacial structure of a few atomic layers.The interfacial structure is slightly expanded,less ordered and defective compared to the MgO matrix due to compositional deviations,whereby the MgO substrate is altered as a poorer template to nucleate Mg solid.Upon solidification in a TP-1 mould,the impotent MgO particles account for the grain refining mechanism,where they are suggested to participate into nucleation and grain initiation processes in an explosive manner.This work not only reveals the atomic engineering of a substrate through interfacial segregation but also demonstrates the effectiveness of a strategy whereby native MgO particles can be harnessed for grain refinement in Mg-Ca alloys.展开更多
In order to obtain Mg alloys with fine microstructures and high mechanical performances,a novel friction-based processing method,name as“constrained friction processing(CFP)”,was investigated.Via CFP,defect-free Mg-...In order to obtain Mg alloys with fine microstructures and high mechanical performances,a novel friction-based processing method,name as“constrained friction processing(CFP)”,was investigated.Via CFP,defect-free Mg-Zn-Ca rods with greatly refined grains and high mechanical properties were produced.Compared to the previous as-cast microstructure,the grain size was reduced from more than 1 mm to around 4μm within 3 s by a single process cycle.The compressive yield strength was increased by 350%while the ultimate compressive strength by 53%.According to the established material flow behaviors by“tracer material”,the plastic material was transported by shear deformation.From the base material to the rod,the material experienced three stages,i.e.deformation by the tool,upward flow with additional tilt,followed by upward transportation.The microstructural evolution was revealed by“stop-action”technique.The microstructural development at regions adjacent to the rod is mainly controlled by twinning,dynamic recrystallization(DRX)as well as particle stimulated nucleation,while that within the rod is related to DRX combined with grain growth.展开更多
Additive manufacturing(AM)of Mg alloys has become a promising strategy for producing complex structures,but the corrosion performance of AM Mg components remains unexploited.In this study,wire and arc additive manufac...Additive manufacturing(AM)of Mg alloys has become a promising strategy for producing complex structures,but the corrosion performance of AM Mg components remains unexploited.In this study,wire and arc additive manufacturing(WAAM)was employed to produce single AZ31 layer.The results revealed that the WAAM AZ31 was characterized by significant grain refinement with non-textured crystallographic orientation,similar phase composition and stabilized corrosion performance comparing to the cast AZ31.These varied corrosion behaviors were principally ascribed to the size of grain,where cast AZ31 and WAAM AZ31 were featured by micro galvanic corrosion and intergranular corrosion,respectively.展开更多
The effects of different complex shear stress conditions on grain refinement and texture evolution of Mg-13Gd-4Y-2Zn-0.5Zr alloy were investigated.With increasing strain rate,the average grain size of compression-shea...The effects of different complex shear stress conditions on grain refinement and texture evolution of Mg-13Gd-4Y-2Zn-0.5Zr alloy were investigated.With increasing strain rate,the average grain size of compression-shear(CS)and compression-torsion(CT)samples are decreased,and the grain size of dynamic recrystallization(DRX)grains is also decreased.This is because that the precipitation number ofβphases is increased,and the hindering effect on grain growth can be significantly enhanced.The DRX fractions of CS and CT samples are decreased with increased strain rate.The low DRX fraction at high strain rate is related to the insufficient time for grains to nucleate.The DRX process can be promoted by the PSN mechanism of second phases,and the grain growth can be restricted by the pinning effect.At the same time,the texture strength is enhanced as the strain rate increased.Besides,the kinking degree of lamellar long-period stacking ordered(LPSO)phases is increased.Under complex shear stress conditions,non-basal slip,especially pyramidal slip,is easily activated and the texture is deflected greatly.Compared with the CS samples,CT samples have smaller average grain size,higher DRX fraction,and lower texture strength for a certain strain rate.This is because that the equivalent stress of the CT sample is larger,the stress triaxiality is smaller,so more serious dislocations are piled up near grain boundaries and second phases.At the same time,since CT sample was sheared with torsion,the dislocation movement path can be called“rotational dislocation accumulation”,and the longer distribution path of the CT sample is generated,so more sub-grains and low-angle grain boundaries(LAGBs)are formed.Compared with the CS sample,more huge-angle grain boundaries(HAGBs)and DRX grains are formed from grain boundary to grain interior,so better grain refinement effect is achieved.展开更多
Low absolute strength becomes one major obstacle for the wider applications of low/no rare-earth(RE) containing Mg alloys. This review firstly demonstrates the importance of grain refinement in improving strength of M...Low absolute strength becomes one major obstacle for the wider applications of low/no rare-earth(RE) containing Mg alloys. This review firstly demonstrates the importance of grain refinement in improving strength of Mg alloys by comprehensively comparing with other strategy, e.g., precipitation strengthening. Dynamic recrystallization(DRX) plays a crucial role in refining grain size of Mg wrought alloys.Therefore, secondly, the DRX models, grain nucleation mechanisms and the related grain refinement abilities in Mg alloys are summarized,including phase boundary, twin boundary and general boundary induced recrystallization. Thirdly, the newly developed low-RE containing Mg alloy, e.g., Mg-Ce, Mg-Nd and Mg-Sm based alloys, and the RE-free Mg alloys, e.g., Mg-Al, Mg-Zn, Mg-Sn and Mg-Ca based alloy,are reviewed, with the focus on enhancing the mechanical properties mainly via the grain refinement strategy. At the last section, the perspectives and outstanding issues concerning high-performance Mg wrought alloys are also proposed. This review is meant to promote the deep understanding on the critical role of grain refinement in Mg alloys and provide reference for the development of other high strength and low-cost Mg alloys which are fabricated by the conventional extrusion/rolling processing.展开更多
High-performance cast magnesium rare-earth(Mg-RE) alloys are one of the most important materials among all developed Mg alloy families, and have shown great potential in military and weapons, aerospace and aviation, o...High-performance cast magnesium rare-earth(Mg-RE) alloys are one of the most important materials among all developed Mg alloy families, and have shown great potential in military and weapons, aerospace and aviation, orthopedic implants, etc. Controlling grain size and distribution of it is key to the promising mechanical performance of Mg-RE alloy casting components. During the casting of a real component, nearly every procedure in the fabrication process will influence the grain refinement effect. The procedure may include and may not be limited to the chemical inoculations, possibly applied physical fields, the interfere between grain refiner and purifications, and the casting techniques with different processing parameters. This paper reviews the recent advances and proposed future developments in these categories on grain refinement of cast Mg-RE alloys. The review will provide insights for the future design of grain refinement techniques,the choosing of processing parameters, and coping strategies for the failure of coarsening for cast Mg-RE components with high quality and good performance.展开更多
A wide-spectrum pulsed magnetic field(WSPMF)was obtained by adjusting the number of current pulses and the pulse interval between adjacent pulses.The effect of WSPMF on the grain refinement of pure aluminium was studi...A wide-spectrum pulsed magnetic field(WSPMF)was obtained by adjusting the number of current pulses and the pulse interval between adjacent pulses.The effect of WSPMF on the grain refinement of pure aluminium was studied.The distribution of electromagnetic force and flow field in the melt under the WSPMF was simulated to reveal the grain refining mechanism.Results show that the grain refinement is attributed to the combined effect of the melt flow and oscillation under a WSPMF.When the pulse interval is 5 ms,the extreme value of electromagnetic force is the highest,and the size of the crystal nucleus is 0.35 mm.In the case of similar flow rates,the grain size gradually decreases as the pulse interval increases.The range of the harmonic frequency of the magnetic field gradually expands with the increase of the pulse interval,which can provide more energy for nucleation at the solid-liquid interface and promote nucleation.展开更多
Numerical simulation is one of the important auxiliary methods for studying materials-related problems. In this study, phase field simulation was employed to investigate the refinement behavior of BAg55CuZn-x B brazin...Numerical simulation is one of the important auxiliary methods for studying materials-related problems. In this study, phase field simulation was employed to investigate the refinement behavior of BAg55CuZn-x B brazing alloys. Simulation and experimental studies were conducted for B contents ranging from 0 wt.% to 0.2 wt.%. The results demonstrated that the addition of 0.05 wt.% B in the brazing alloy leads to a significant refinement effect. As the B content increases, the grain size further reduces, and a refinement stagnation phenomenon occurs after exceeding 0.15 wt.%. The solidification process of brazing alloys with different B content was predicted by simulation, and the simulation results showed that with the increase of B content, the initial number of nucleation increased, and the radius of the dendrite tip decreased. The simulation results are in good agreement with the experimental findings, providing further evidence of the refining effect of the B element and the reliable predictive capability of the phase field model.展开更多
The experiment employed the use of melt purification and cyclic superheating technique to achieve maximum undercooling of Ni65Cu31Co4 alloy at 300K.Simultaneously,high-speed photography techniques were used to capture...The experiment employed the use of melt purification and cyclic superheating technique to achieve maximum undercooling of Ni65Cu31Co4 alloy at 300K.Simultaneously,high-speed photography techniques were used to capture the process of alloy liquid phase interface migration,and analyzed the relationship between the shape characteristics of the front end of alloy solidification and undercooling.The microstructure of the alloy was observed through metallographic microscopy,and the micro-morphological characteristics and evolution of the rapidly solidified microstructure were systematically studied.It is found that the grain refinement mechanism of Ni-Cu-Co ternary alloy is similar to that of Ni-Cu binary alloy.Grain refinement at low undercooling is caused by intense dendritic remelting,while grain refinement at high undercooling is attributed to recrystallization,driven by the stress and plastic strain accumulated from the interaction of liquid flow and primary dendrites caused by rapid solidification.It also shows that the addition of the third element Co plays a significant role in solidification rate and re-ignition effect.展开更多
Through the use of purification and recirculation superheating techniques on molten glass,the Ni65Cu33Co2 alloy was successfully undercooled to a maximum temperature of 292 K.High-speed photography was employed to cap...Through the use of purification and recirculation superheating techniques on molten glass,the Ni65Cu33Co2 alloy was successfully undercooled to a maximum temperature of 292 K.High-speed photography was employed to capture the process of interface migration of the alloy liquid,allowing for an analysis of the relationship between the morphological characteristics of the alloy liquid solidification front and the degree of undercooling.Additionally,the microstructure of the alloy was examined using metallographic microscopy,leading to a systematic study of the microscopic morphological characteristics and evolution laws of the refined structure during rapid solidification.The research reveals that the grain refining mechanism of the Ni-Cu-Co ternary alloy is consistent with that of the binary alloy(Ni-Cu).Specifically,under low undercooling conditions,intense dendritic remelting was found to cause grain refinement,while under high undercooling conditions,recrystallization driven by accumulated stress and plastic strain resulting from the interaction between the liquid flow and the primary dendrites caused by rapid solidification was identified as the main factor contributing to grain refinement.Furthermore,the study highlights the significant role of the Co element in influencing the solidification rate and reheat effect of the alloy.The addition of Co was also found to facilitate the formation of non-segregated solidification structure,indicating its importance in the overall solidification process.展开更多
The effects of nano-CaO contents on the microstructure,mechanical properties and corrosion resistance of lean Mg-1Zn alloy were investigated.The results showed that the addition of nano-CaO significantly refined the g...The effects of nano-CaO contents on the microstructure,mechanical properties and corrosion resistance of lean Mg-1Zn alloy were investigated.The results showed that the addition of nano-CaO significantly refined the grain size and improved mechanical properties of the Mg-1Zn alloy.At the same time,CaO reacted with molten Mg in situ to form nano-MgO,whose corrosion product in SBF solution was the same with the degradation product of Mg matrix,resulting in the enhanced compactness of the Mg(OH)_(2) layer and reduced corrosion rate of matrix.The Mg-1Zn alloy had lower corrosion resistance due to excessively large grain size and shedding of corrosion products.The composite with 0.5 wt.%CaO had the best corrosion resistance with a weight loss of 9.875 mg·y^(-1)·mm^(-2)due to the small number of Ca_(2)Mg_(6)Zn_(3) phase and suitable grain size.While for composites with high content of CaO(0.7 wt.%and 1.0 wt.%),they had lower corrosion resistance due to the coexistence of large number of Ca_(2)Mg_(6)Zn_(3) and Mg_(2)Ca at grain boundaries,especially for 1.0 wt.%CaO composite,resulting from the strong micro-galvanic corrosion.展开更多
Magnesium(Mg) alloys, as the lightest metal engineering materials, have broad application prospects.However, the strength and ductility of traditional Mg alloys are still relativity low and difficult to improve simult...Magnesium(Mg) alloys, as the lightest metal engineering materials, have broad application prospects.However, the strength and ductility of traditional Mg alloys are still relativity low and difficult to improve simultaneously.Refining grain size via the deformation process based on the grain boundary strengthening and the transition of deformation mechanisms is one of the feasible strategies to prepare Mg alloys with high strength and high ductility.In this review, the effects of grain size on the strength and ductility of Mg alloys are summarized, and fine-grained Mg alloys with high strength and high ductility developed by various severe plastic deformation technologies and improved traditional deformation technologies are introduced.Although some achievements have been made, the effects of grain size on various Mg alloys are rarely discussed systematically and some key mechanisms are unclear or lack direct microscopic evidence.This review can be used as a reference for further development of high-performance fine-grained Mg alloys.展开更多
Magnesium is the lightest constructional metal,which makes it an important material for different applications like automotive,transportation,aviation and aerospace.There are several studies about developing propertie...Magnesium is the lightest constructional metal,which makes it an important material for different applications like automotive,transportation,aviation and aerospace.There are several studies about developing properties of existing Mg alloys and introducing new alloy systems to industrial producers.An important way to improve properties of metallic materials is to decrease grain size that results almost in increasing all kind of properties of the material.This review paper aims to summarize the literature about grain refining of magnesium alloys.The text is consisting of three sections,which focused on the(1)grain refining methods used in the past,which are not used today,(2)grain refining methods currently being used in the industry and(3)novel and newly developed methods that may find usage in the industry in future.Before explaining grain refining methods of magnesium alloys a general summary about grain refinement of metals is also provided.展开更多
The microstructural features and grain refinement in the coarse-grained region of the heat-affected zone in low-carbon high-strength microalloyed steels were investigated using optical microscopy, scanning electron mi...The microstructural features and grain refinement in the coarse-grained region of the heat-affected zone in low-carbon high-strength microalloyed steels were investigated using optical microscopy, scanning electron microscopy, and electron backscattering dif- fraction. The coarse-grained region of the heat-affected zone consists of predominantly bainite and a small proportion of acicular ferrite. Bainite packets are separated by high angle boundaries. Acicular ferrite laths or plates in the coarse-grained region of the heat-affected zone formed prior to bainite packets partition austenite grains into many smaller and separate areas, resulting in fine-grained mixed microstruc- tures. Electron backscattefing diffraction analysis indicates that the average crystallographic grain size of the coarse-grained region of the heat-affected zone reaches 6-9 μm, much smaller than that of anstanite grains.展开更多
Grain refinement can strengthen the mechanical properties of materials according to the classical Hall-Petch relationship but does not always result in better corrosion resistance.During the past few decades,various t...Grain refinement can strengthen the mechanical properties of materials according to the classical Hall-Petch relationship but does not always result in better corrosion resistance.During the past few decades,various techniques have been dedicated to refining grain,along with relevant studies on corrosion behavior,including general corrosion,pitting corrosion,and stress corrosion cracking.However,the funda-mental consensus on how grain size influences corrosion behavior has not been reached.This paper reviews existing literature on the beneficial and detrimental effects of grain refinement on corrosion behavior.Moreover,the effects of microstructural changes(i.e.,grain boundary,dislo-cation,texture,residual stress,impurities,and second phase)resulting from grain refinement on corrosion behavior are discussed.The grain re-finement not only has an impact on the corrosion performance,but also results in microstructural changes that have a non-negligible effect on corrosion behavior or even outweigh that of grain refinement.Grain size is not the only factor affecting the corrosion behavior of metallic ma-terials;thus,the overall influence of microstructures on corrosion behavior should be understood.展开更多
As a potent nucleating substrate forα-Mg grain,MgAl_(2)O_(4) powder was used to inoculate the Mg-Al melt in this study.The effects of MgAl_(2)O_(4)amount,holding time and Al content on the grain size and grain refini...As a potent nucleating substrate forα-Mg grain,MgAl_(2)O_(4) powder was used to inoculate the Mg-Al melt in this study.The effects of MgAl_(2)O_(4)amount,holding time and Al content on the grain size and grain refining ratio of the inoculated Mg-Al alloys are systematically investigated.The results show that the minimum grain size of Mg-3Al alloy is achieved by adding 2wt.%MgAl_(2)O_(4)powder and this alloy exhibits higher grain refining ratio than Mg-5Al and Mg-8Al alloys.The crystallographic misfit calculation indicates the wellmatching and possible orientation relationships(ORs)betweenα-Mg and MgAl_(2)O_(4).Among these predicted ORs,[10–10]α−Mg//[110]MgAl2O4 in(0002)α−Mg//(1–13)MgAl2O4 possesses the smallest misfit,i.e.,2.34%(fr).Both results of the experiment and crystallographic calculation demonstrate that the grain refinement of Mg-Al alloys is attributed to the MgAl_(2)O_(4)particles acting as the heterogeneous nucleation substrates forα-Mg grains.展开更多
A series of Mge10(AlþY)alloys with various weight ratios of Al to Y were cast to investigate the role of Al_(2)Y in grain refinement in MgeAleY ternary system.Thermal analysis combined with microstructural and ED...A series of Mge10(AlþY)alloys with various weight ratios of Al to Y were cast to investigate the role of Al_(2)Y in grain refinement in MgeAleY ternary system.Thermal analysis combined with microstructural and EDX analysis was used to determine the phase transformation temperatures during solidification process.Experimental results show that when the Al content is below 4 wt%,a peritectic reaction,LþAl_(2)Y/a-Mg,occurs after the intermetallic Al_(2)Y forms directly from the melt as a pro-peritectic phase.Once the Al content is above 4 wt%,an eutectic reaction occurs at a lower temperature.The presence of the pro-peritectic phase can lead to nucleation of a-Mg directly through a peritectic reaction although grain refining efficiency is also closely related to the active particle size.In the case where solidification does not involve a peritectic reaction,the growth restriction factor,quantitatively the Q-value,governs the grain refining efficiency.Higher Q-value corresponds to finer grains.展开更多
Commercial A356 alloy was refined with a homemade A1-5Ti-0.25C-2RE master alloy, and the microstructure and macrostructure of the refined alloy were investigated. The results show that the grain refining effect of A35...Commercial A356 alloy was refined with a homemade A1-5Ti-0.25C-2RE master alloy, and the microstructure and macrostructure of the refined alloy were investigated. The results show that the grain refining effect of A356 is poor by the addition level of 0.5 wt% master alloy, but when the level reaches 3.0 wt% the grain can get a satisfactory refining effect. Dendrite of A356 can be effectively refined by addition of 0.5 wt% master alloy; however, the refining effect is not significantly improved by further increasing the addition of master alloy. Grain and dendrite refining effects are compared in this article, and the results show that the grain and dendrite exhibit different refining effects with the same addition level of master alloy. Dendrite is easier to reach the optimal refining effect than grain.展开更多
The grain refining process of an AZ91D Mg alloy by Sr addition was studied and the heterogeneous nucleating particles of α-Mg were investigated by electron probe microanalysis (EPMA). With 0.6 wt% Sr addition, the ...The grain refining process of an AZ91D Mg alloy by Sr addition was studied and the heterogeneous nucleating particles of α-Mg were investigated by electron probe microanalysis (EPMA). With 0.6 wt% Sr addition, the mean grain size of AZ91D alloy was refined from 235.4μm to 52.5 μm at the one-half radius of the ingot. The morphology of primary crystal changed from a sixford symmetrical shape to a petallike shape, Mg-Sr-Al-Fe-Mn heterogeneous nucleating particles were observed at the grain centers and Sr solute atoms presented segregation along the grain boundaries. Grain refinement was facilitated by both the Mg-Sr-Al- Fe-Mn nucleating particles and the Sr solute atoms, and the former played a dominate role in the process.展开更多
In this study, grain refining effect of Al-1.5℃ master alloy was examined on an AZ63B magnesium alloy, and the refining mechanism was studied through investigating the role of C and Fe in this process. The results sh...In this study, grain refining effect of Al-1.5℃ master alloy was examined on an AZ63B magnesium alloy, and the refining mechanism was studied through investigating the role of C and Fe in this process. The results show that addition of Al-1.5℃ master alloy leads to significant decrease of the mean grain size from about 270μm to 50μm at the center of the AZ63 alloy ingot. Grain refinement by carbon addition is mainly due to the heterogeneity nucleation on the Al-, C-, O-, Fe- and Mn-rich particles, but not constitutional undercooling caused by the carbon solute element. Fe plays an important role in the formation of the nucleating particles, but not acts as an inhibiting element.展开更多
基金financial support under grant number EP/N007638/1supported by EPSRC under grant number EP/W021080/1
文摘In Mg-Ca alloys the grain refining mechanism,in particular regarding the role of nucleant substrates,remains the object of debates.Although native MgO is being recognised as a nucleating substrate accounting for grain refinement of Mg alloys,the possible interactions of MgO with alloying elements that may alter the nucleation potency have not been elucidated yet.Herein,we design casting experiments of Mg-xCa alloys varied qualitatively in number density of native MgO,which are then comprehensively studied by advanced electron microscopy.The results show that grain refinement is enhanced as the particle number density of MgO increases.The native MgO particles are modified by interfacial layers due to the co-segregation of Ca and N solute atoms at the MgO/Mg interface.Using aberration-corrected scanning transmission electron microscopy and electron energy loss spectroscopy,we reveal the nature of these Ca/N interfacial layers at the atomic scale.Irrespective of the crystallographic termination of MgO,Ca and N co-segregate at the MgO/Mg interface and occupy Mg and O sites,respectively,forming an interfacial structure of a few atomic layers.The interfacial structure is slightly expanded,less ordered and defective compared to the MgO matrix due to compositional deviations,whereby the MgO substrate is altered as a poorer template to nucleate Mg solid.Upon solidification in a TP-1 mould,the impotent MgO particles account for the grain refining mechanism,where they are suggested to participate into nucleation and grain initiation processes in an explosive manner.This work not only reveals the atomic engineering of a substrate through interfacial segregation but also demonstrates the effectiveness of a strategy whereby native MgO particles can be harnessed for grain refinement in Mg-Ca alloys.
基金the China Scholarship Council for the award of fellowship and funding(No.202006230137)。
文摘In order to obtain Mg alloys with fine microstructures and high mechanical performances,a novel friction-based processing method,name as“constrained friction processing(CFP)”,was investigated.Via CFP,defect-free Mg-Zn-Ca rods with greatly refined grains and high mechanical properties were produced.Compared to the previous as-cast microstructure,the grain size was reduced from more than 1 mm to around 4μm within 3 s by a single process cycle.The compressive yield strength was increased by 350%while the ultimate compressive strength by 53%.According to the established material flow behaviors by“tracer material”,the plastic material was transported by shear deformation.From the base material to the rod,the material experienced three stages,i.e.deformation by the tool,upward flow with additional tilt,followed by upward transportation.The microstructural evolution was revealed by“stop-action”technique.The microstructural development at regions adjacent to the rod is mainly controlled by twinning,dynamic recrystallization(DRX)as well as particle stimulated nucleation,while that within the rod is related to DRX combined with grain growth.
基金the financial support by National Key Research and Development Project(Grand No.2020YFC1107202)Guangdong Basic and Applied Basic Research Foundation(Grand No.2020A1515110754)+3 种基金MOE Key Lab of Disaster Forest and Control in Engineering,Jinan University(Grand No.20200904008)Educational Commission of Guangdong Province(Grand No.2020KTSCX012)the Fundamental Research Funds for Central Universities(Grand No.21620342)the support from National Natural Science Foundation of China,NSFC(Grand No.51775556)。
文摘Additive manufacturing(AM)of Mg alloys has become a promising strategy for producing complex structures,but the corrosion performance of AM Mg components remains unexploited.In this study,wire and arc additive manufacturing(WAAM)was employed to produce single AZ31 layer.The results revealed that the WAAM AZ31 was characterized by significant grain refinement with non-textured crystallographic orientation,similar phase composition and stabilized corrosion performance comparing to the cast AZ31.These varied corrosion behaviors were principally ascribed to the size of grain,where cast AZ31 and WAAM AZ31 were featured by micro galvanic corrosion and intergranular corrosion,respectively.
基金supported by Project supported by the Joint Funds of the National Natural Science Foundation of China(Grant No.U20A20230)Natural Science Foundation of Shanxi Province(No.201901D111176)+2 种基金Project supported by the Key R&D program of Shanxi Province(No.2020XXX015)Research Project Supported by Shanxi Scholarship Council of China(2021-127)Graduate Education Innovation Program of Shanxi Province(2022Y579).
文摘The effects of different complex shear stress conditions on grain refinement and texture evolution of Mg-13Gd-4Y-2Zn-0.5Zr alloy were investigated.With increasing strain rate,the average grain size of compression-shear(CS)and compression-torsion(CT)samples are decreased,and the grain size of dynamic recrystallization(DRX)grains is also decreased.This is because that the precipitation number ofβphases is increased,and the hindering effect on grain growth can be significantly enhanced.The DRX fractions of CS and CT samples are decreased with increased strain rate.The low DRX fraction at high strain rate is related to the insufficient time for grains to nucleate.The DRX process can be promoted by the PSN mechanism of second phases,and the grain growth can be restricted by the pinning effect.At the same time,the texture strength is enhanced as the strain rate increased.Besides,the kinking degree of lamellar long-period stacking ordered(LPSO)phases is increased.Under complex shear stress conditions,non-basal slip,especially pyramidal slip,is easily activated and the texture is deflected greatly.Compared with the CS samples,CT samples have smaller average grain size,higher DRX fraction,and lower texture strength for a certain strain rate.This is because that the equivalent stress of the CT sample is larger,the stress triaxiality is smaller,so more serious dislocations are piled up near grain boundaries and second phases.At the same time,since CT sample was sheared with torsion,the dislocation movement path can be called“rotational dislocation accumulation”,and the longer distribution path of the CT sample is generated,so more sub-grains and low-angle grain boundaries(LAGBs)are formed.Compared with the CS sample,more huge-angle grain boundaries(HAGBs)and DRX grains are formed from grain boundary to grain interior,so better grain refinement effect is achieved.
基金supported by National Key Research and Development Program of China (No.2023YFB3710900)National Natural Science Foundation of China (Nos.U2241235,U2167213,51971053)+2 种基金funded by the Project of Promoting Talents in Liaoning province (No.XLYC2203202)the financial assistance from Young Elite Scientists Sponsorship Program by CAST (2019-2021QNRC001,2019-2021QNRC002,2019-2021QNRC003)the fund from the Fundamental Research Funds for the Central Universities (N2202020)。
文摘Low absolute strength becomes one major obstacle for the wider applications of low/no rare-earth(RE) containing Mg alloys. This review firstly demonstrates the importance of grain refinement in improving strength of Mg alloys by comprehensively comparing with other strategy, e.g., precipitation strengthening. Dynamic recrystallization(DRX) plays a crucial role in refining grain size of Mg wrought alloys.Therefore, secondly, the DRX models, grain nucleation mechanisms and the related grain refinement abilities in Mg alloys are summarized,including phase boundary, twin boundary and general boundary induced recrystallization. Thirdly, the newly developed low-RE containing Mg alloy, e.g., Mg-Ce, Mg-Nd and Mg-Sm based alloys, and the RE-free Mg alloys, e.g., Mg-Al, Mg-Zn, Mg-Sn and Mg-Ca based alloy,are reviewed, with the focus on enhancing the mechanical properties mainly via the grain refinement strategy. At the last section, the perspectives and outstanding issues concerning high-performance Mg wrought alloys are also proposed. This review is meant to promote the deep understanding on the critical role of grain refinement in Mg alloys and provide reference for the development of other high strength and low-cost Mg alloys which are fabricated by the conventional extrusion/rolling processing.
基金supported by the National Natural Science Foundation of China (Grant Nos.U2037601,51821001,and 52105348)the Natural Science Foundation for Young of Jiangsu Province (Grant No.BK20190863)the Research Program of Joint Research Center of Advanced Spaceflight Technologies (No.USCAST2020-31)。
文摘High-performance cast magnesium rare-earth(Mg-RE) alloys are one of the most important materials among all developed Mg alloy families, and have shown great potential in military and weapons, aerospace and aviation, orthopedic implants, etc. Controlling grain size and distribution of it is key to the promising mechanical performance of Mg-RE alloy casting components. During the casting of a real component, nearly every procedure in the fabrication process will influence the grain refinement effect. The procedure may include and may not be limited to the chemical inoculations, possibly applied physical fields, the interfere between grain refiner and purifications, and the casting techniques with different processing parameters. This paper reviews the recent advances and proposed future developments in these categories on grain refinement of cast Mg-RE alloys. The review will provide insights for the future design of grain refinement techniques,the choosing of processing parameters, and coping strategies for the failure of coarsening for cast Mg-RE components with high quality and good performance.
基金financially supported by the National Natural Science Foundation of China(Grant Nos.52071194,U1760204)the National Key Research Program of China(Grant Nos.2020YFB2008401 and 2017YFB0701800)。
文摘A wide-spectrum pulsed magnetic field(WSPMF)was obtained by adjusting the number of current pulses and the pulse interval between adjacent pulses.The effect of WSPMF on the grain refinement of pure aluminium was studied.The distribution of electromagnetic force and flow field in the melt under the WSPMF was simulated to reveal the grain refining mechanism.Results show that the grain refinement is attributed to the combined effect of the melt flow and oscillation under a WSPMF.When the pulse interval is 5 ms,the extreme value of electromagnetic force is the highest,and the size of the crystal nucleus is 0.35 mm.In the case of similar flow rates,the grain size gradually decreases as the pulse interval increases.The range of the harmonic frequency of the magnetic field gradually expands with the increase of the pulse interval,which can provide more energy for nucleation at the solid-liquid interface and promote nucleation.
基金the Major Science and Technology Project of Henan Province.(No.221100230300).
文摘Numerical simulation is one of the important auxiliary methods for studying materials-related problems. In this study, phase field simulation was employed to investigate the refinement behavior of BAg55CuZn-x B brazing alloys. Simulation and experimental studies were conducted for B contents ranging from 0 wt.% to 0.2 wt.%. The results demonstrated that the addition of 0.05 wt.% B in the brazing alloy leads to a significant refinement effect. As the B content increases, the grain size further reduces, and a refinement stagnation phenomenon occurs after exceeding 0.15 wt.%. The solidification process of brazing alloys with different B content was predicted by simulation, and the simulation results showed that with the increase of B content, the initial number of nucleation increased, and the radius of the dendrite tip decreased. The simulation results are in good agreement with the experimental findings, providing further evidence of the refining effect of the B element and the reliable predictive capability of the phase field model.
基金Funded by the Natural Science Foundation of Shanxi Province(No.202203021211093)。
文摘The experiment employed the use of melt purification and cyclic superheating technique to achieve maximum undercooling of Ni65Cu31Co4 alloy at 300K.Simultaneously,high-speed photography techniques were used to capture the process of alloy liquid phase interface migration,and analyzed the relationship between the shape characteristics of the front end of alloy solidification and undercooling.The microstructure of the alloy was observed through metallographic microscopy,and the micro-morphological characteristics and evolution of the rapidly solidified microstructure were systematically studied.It is found that the grain refinement mechanism of Ni-Cu-Co ternary alloy is similar to that of Ni-Cu binary alloy.Grain refinement at low undercooling is caused by intense dendritic remelting,while grain refinement at high undercooling is attributed to recrystallization,driven by the stress and plastic strain accumulated from the interaction of liquid flow and primary dendrites caused by rapid solidification.It also shows that the addition of the third element Co plays a significant role in solidification rate and re-ignition effect.
基金Funded by the Basic Research Project in Shanxi Province(No.202103021224183)。
文摘Through the use of purification and recirculation superheating techniques on molten glass,the Ni65Cu33Co2 alloy was successfully undercooled to a maximum temperature of 292 K.High-speed photography was employed to capture the process of interface migration of the alloy liquid,allowing for an analysis of the relationship between the morphological characteristics of the alloy liquid solidification front and the degree of undercooling.Additionally,the microstructure of the alloy was examined using metallographic microscopy,leading to a systematic study of the microscopic morphological characteristics and evolution laws of the refined structure during rapid solidification.The research reveals that the grain refining mechanism of the Ni-Cu-Co ternary alloy is consistent with that of the binary alloy(Ni-Cu).Specifically,under low undercooling conditions,intense dendritic remelting was found to cause grain refinement,while under high undercooling conditions,recrystallization driven by accumulated stress and plastic strain resulting from the interaction between the liquid flow and the primary dendrites caused by rapid solidification was identified as the main factor contributing to grain refinement.Furthermore,the study highlights the significant role of the Co element in influencing the solidification rate and reheat effect of the alloy.The addition of Co was also found to facilitate the formation of non-segregated solidification structure,indicating its importance in the overall solidification process.
基金the financial support for this work from the National Natural Science Foundation of China(Nos.52171241,52201301 and 51871166)。
文摘The effects of nano-CaO contents on the microstructure,mechanical properties and corrosion resistance of lean Mg-1Zn alloy were investigated.The results showed that the addition of nano-CaO significantly refined the grain size and improved mechanical properties of the Mg-1Zn alloy.At the same time,CaO reacted with molten Mg in situ to form nano-MgO,whose corrosion product in SBF solution was the same with the degradation product of Mg matrix,resulting in the enhanced compactness of the Mg(OH)_(2) layer and reduced corrosion rate of matrix.The Mg-1Zn alloy had lower corrosion resistance due to excessively large grain size and shedding of corrosion products.The composite with 0.5 wt.%CaO had the best corrosion resistance with a weight loss of 9.875 mg·y^(-1)·mm^(-2)due to the small number of Ca_(2)Mg_(6)Zn_(3) phase and suitable grain size.While for composites with high content of CaO(0.7 wt.%and 1.0 wt.%),they had lower corrosion resistance due to the coexistence of large number of Ca_(2)Mg_(6)Zn_(3) and Mg_(2)Ca at grain boundaries,especially for 1.0 wt.%CaO composite,resulting from the strong micro-galvanic corrosion.
基金supported by the National Natural Science Foundation of China (Nos.51871069 and 52071093)the Fundamental Research Funds for the Central Universities (No.3072020CF1009)+2 种基金the Science and Technology Innovation Major Project of Ningbo City, China (No.2019B10103)the Domain Foundation of Equipment Advance Research of 13th Five-year Plan (No.61409220118)the Open Funds of the State Key Laboratory of Rare Earth Resource Utilization (No.RERU2020008)。
文摘Magnesium(Mg) alloys, as the lightest metal engineering materials, have broad application prospects.However, the strength and ductility of traditional Mg alloys are still relativity low and difficult to improve simultaneously.Refining grain size via the deformation process based on the grain boundary strengthening and the transition of deformation mechanisms is one of the feasible strategies to prepare Mg alloys with high strength and high ductility.In this review, the effects of grain size on the strength and ductility of Mg alloys are summarized, and fine-grained Mg alloys with high strength and high ductility developed by various severe plastic deformation technologies and improved traditional deformation technologies are introduced.Although some achievements have been made, the effects of grain size on various Mg alloys are rarely discussed systematically and some key mechanisms are unclear or lack direct microscopic evidence.This review can be used as a reference for further development of high-performance fine-grained Mg alloys.
文摘Magnesium is the lightest constructional metal,which makes it an important material for different applications like automotive,transportation,aviation and aerospace.There are several studies about developing properties of existing Mg alloys and introducing new alloy systems to industrial producers.An important way to improve properties of metallic materials is to decrease grain size that results almost in increasing all kind of properties of the material.This review paper aims to summarize the literature about grain refining of magnesium alloys.The text is consisting of three sections,which focused on the(1)grain refining methods used in the past,which are not used today,(2)grain refining methods currently being used in the industry and(3)novel and newly developed methods that may find usage in the industry in future.Before explaining grain refining methods of magnesium alloys a general summary about grain refinement of metals is also provided.
基金supported by the National Natural Science Foundation of China (No.50734004)
文摘The microstructural features and grain refinement in the coarse-grained region of the heat-affected zone in low-carbon high-strength microalloyed steels were investigated using optical microscopy, scanning electron microscopy, and electron backscattering dif- fraction. The coarse-grained region of the heat-affected zone consists of predominantly bainite and a small proportion of acicular ferrite. Bainite packets are separated by high angle boundaries. Acicular ferrite laths or plates in the coarse-grained region of the heat-affected zone formed prior to bainite packets partition austenite grains into many smaller and separate areas, resulting in fine-grained mixed microstruc- tures. Electron backscattefing diffraction analysis indicates that the average crystallographic grain size of the coarse-grained region of the heat-affected zone reaches 6-9 μm, much smaller than that of anstanite grains.
基金This work was fianancially supported by the National Natural Science Foundation of China(No.51871024)the Fundamental Research Funds for the Central Universities(No.FRF-NP-20-07).
文摘Grain refinement can strengthen the mechanical properties of materials according to the classical Hall-Petch relationship but does not always result in better corrosion resistance.During the past few decades,various techniques have been dedicated to refining grain,along with relevant studies on corrosion behavior,including general corrosion,pitting corrosion,and stress corrosion cracking.However,the funda-mental consensus on how grain size influences corrosion behavior has not been reached.This paper reviews existing literature on the beneficial and detrimental effects of grain refinement on corrosion behavior.Moreover,the effects of microstructural changes(i.e.,grain boundary,dislo-cation,texture,residual stress,impurities,and second phase)resulting from grain refinement on corrosion behavior are discussed.The grain re-finement not only has an impact on the corrosion performance,but also results in microstructural changes that have a non-negligible effect on corrosion behavior or even outweigh that of grain refinement.Grain size is not the only factor affecting the corrosion behavior of metallic ma-terials;thus,the overall influence of microstructures on corrosion behavior should be understood.
基金This work was supported by the National Natural Science Foundation of China(51871100).
文摘As a potent nucleating substrate forα-Mg grain,MgAl_(2)O_(4) powder was used to inoculate the Mg-Al melt in this study.The effects of MgAl_(2)O_(4)amount,holding time and Al content on the grain size and grain refining ratio of the inoculated Mg-Al alloys are systematically investigated.The results show that the minimum grain size of Mg-3Al alloy is achieved by adding 2wt.%MgAl_(2)O_(4)powder and this alloy exhibits higher grain refining ratio than Mg-5Al and Mg-8Al alloys.The crystallographic misfit calculation indicates the wellmatching and possible orientation relationships(ORs)betweenα-Mg and MgAl_(2)O_(4).Among these predicted ORs,[10–10]α−Mg//[110]MgAl2O4 in(0002)α−Mg//(1–13)MgAl2O4 possesses the smallest misfit,i.e.,2.34%(fr).Both results of the experiment and crystallographic calculation demonstrate that the grain refinement of Mg-Al alloys is attributed to the MgAl_(2)O_(4)particles acting as the heterogeneous nucleation substrates forα-Mg grains.
基金The authors would like to thank the CSIRO Flagship in Light Metals and the CAST Cooperative Research Centre(CAST CRC)for financial support.
文摘A series of Mge10(AlþY)alloys with various weight ratios of Al to Y were cast to investigate the role of Al_(2)Y in grain refinement in MgeAleY ternary system.Thermal analysis combined with microstructural and EDX analysis was used to determine the phase transformation temperatures during solidification process.Experimental results show that when the Al content is below 4 wt%,a peritectic reaction,LþAl_(2)Y/a-Mg,occurs after the intermetallic Al_(2)Y forms directly from the melt as a pro-peritectic phase.Once the Al content is above 4 wt%,an eutectic reaction occurs at a lower temperature.The presence of the pro-peritectic phase can lead to nucleation of a-Mg directly through a peritectic reaction although grain refining efficiency is also closely related to the active particle size.In the case where solidification does not involve a peritectic reaction,the growth restriction factor,quantitatively the Q-value,governs the grain refining efficiency.Higher Q-value corresponds to finer grains.
基金financially supported by the National Natural Science Foundation of China (No. 51174177)
文摘Commercial A356 alloy was refined with a homemade A1-5Ti-0.25C-2RE master alloy, and the microstructure and macrostructure of the refined alloy were investigated. The results show that the grain refining effect of A356 is poor by the addition level of 0.5 wt% master alloy, but when the level reaches 3.0 wt% the grain can get a satisfactory refining effect. Dendrite of A356 can be effectively refined by addition of 0.5 wt% master alloy; however, the refining effect is not significantly improved by further increasing the addition of master alloy. Grain and dendrite refining effects are compared in this article, and the results show that the grain and dendrite exhibit different refining effects with the same addition level of master alloy. Dendrite is easier to reach the optimal refining effect than grain.
基金Funded by the National Natural Science Foundation of China (No. 50171037) Key Project of Science and Technology Research of Ministry of Education of China (No. 01105)
文摘The grain refining process of an AZ91D Mg alloy by Sr addition was studied and the heterogeneous nucleating particles of α-Mg were investigated by electron probe microanalysis (EPMA). With 0.6 wt% Sr addition, the mean grain size of AZ91D alloy was refined from 235.4μm to 52.5 μm at the one-half radius of the ingot. The morphology of primary crystal changed from a sixford symmetrical shape to a petallike shape, Mg-Sr-Al-Fe-Mn heterogeneous nucleating particles were observed at the grain centers and Sr solute atoms presented segregation along the grain boundaries. Grain refinement was facilitated by both the Mg-Sr-Al- Fe-Mn nucleating particles and the Sr solute atoms, and the former played a dominate role in the process.
基金supported by the National Natural Science Foundation of China(No.50171037)Natural Science Foundation of Shandong Province of China(No.Z2004F03).
文摘In this study, grain refining effect of Al-1.5℃ master alloy was examined on an AZ63B magnesium alloy, and the refining mechanism was studied through investigating the role of C and Fe in this process. The results show that addition of Al-1.5℃ master alloy leads to significant decrease of the mean grain size from about 270μm to 50μm at the center of the AZ63 alloy ingot. Grain refinement by carbon addition is mainly due to the heterogeneity nucleation on the Al-, C-, O-, Fe- and Mn-rich particles, but not constitutional undercooling caused by the carbon solute element. Fe plays an important role in the formation of the nucleating particles, but not acts as an inhibiting element.