Particle size distribution of coarse aggregates through mechanical sieving gives results in terms of cumu- lative mass percent. But digital image processing generated size distribution of particles, while being fast a...Particle size distribution of coarse aggregates through mechanical sieving gives results in terms of cumu- lative mass percent. But digital image processing generated size distribution of particles, while being fast and accurate, is often expressed in terms of area function or number of particles. In this paper, a mass model is developed which converts the image obtained size distribution to mass-wise distribution, mak- ing it readily comparable to mechanical sieving data. The concept of weight/particle ratio is introduced for mass reconstruction from 2D images of particle aggregates. Using this mass model, the effects of several particle shape parameters （such as major axis, minor axis, and equivalent diameter） on sieve-size of the particles is studied. It is shown that the sieve-size of a particle strongly depend upon the shape param- eters, 91% of its variation being explained by major axis, minor axis, bounding box length and equivalent diameter. Furthermore, minor axis gives an overall accurate estimate of particle sieve-size, error in mean size （D-50） being just 0.4%. However, sieve-size of smaller particles （〈20 ram） strongly depends upon the length of the smaller arm of the bounding box enclosing them and sieve-sizes of larger particles （〉20 mm） are highly correlated to their equivalent diameters. Multiple linear regression analysis has been used to generate overall mass-wise particle size distribution, considering the influences of all these shape parameters on particle sieve-size. Multiple linear regression generated overall mass-wise particle size distribution shows a strong correlation with sieve generated data. The adjusted R-square value of the regression analysis is found to be 99 percent （w.r,t cumulative frequency）. The method proposed in this paper provides a time-efficient way of producing accurate （up to 99%） mass-wise PSD using digital image processing and it can be used effectively to renlace the mechanical sieving.展开更多
This study explores the arrivals of water pipeline break failures. The aim is to assist the facility manager in the decision making process. Based on characteristics of the data set ranging from 2011 to 2014, two step...This study explores the arrivals of water pipeline break failures. The aim is to assist the facility manager in the decision making process. Based on characteristics of the data set ranging from 2011 to 2014, two steps of analysis were presented in the paper. This first step is the analysis of partially complete data set (2011 data). The 2-sample KS test is adopted to check the similarity between this data set and the entire data set with no underlying distribution implied. In order to conduct the reliability analysis, the Weibull distribution is adopted to evaluate the data. For annual data set, the 2-parameter Weibull distribution fits data sets pretty well. The shape parameters are a little greater than 1, indicating a slightly increasing arrival rate of such failures. For the entire data set, the 3-parameter Weibull tends to fit the data better than the 2-parameter Weibull. The shape parameter is well above 1, indicating an increasing arrival rate of the failures. To eliminate the impact of missing points for the 2011 data set, data from 2012 to 2014 were also considered as a new set, the Weibull distribution generated a decent fitting. The shape parameter is a little greater than 1. Therefore, there is a slightly increasing arrival rate of those pipeline failures. Results from this study provide decision makers valuable information in terms of whether additional efforts shall be made to enhance the system’s performance in order to reduce the failure rate.展开更多
To develop modal macro-strain （ MMS ） identification techniques and improve their applicability in a continuous health monitoring system for civil infrastructures, the concept of operational macro-strain shape （OMS...To develop modal macro-strain （ MMS ） identification techniques and improve their applicability in a continuous health monitoring system for civil infrastructures, the concept of operational macro-strain shape （OMSS） and the corresponding identification method are proposed under unknown ever-changing loading conditions, and the MMS is then obtained. The core of the proposed technique is mainly based on the specific property that the macro-strain transmissibility tends to be independent of external excitations at the poles of the system and converges to a unique value. The proposed method is verified using the experimental data from a three-span continuous beam excited by an impact hammer at different locations. The identified results are also compared with the commonly used methods, such as the peak- picking （PP） method, the stochastic subspace identification （SSI） method, and numerical results, in the case of unknown input forces. Results show that the proposed technique has unique merits in accuracy and robustness due to its combining multiple tests under changing loading conditions, which also reveal the promising application of the distributed strain sensing system in identifying MMS of operational structures, as well as in the structural health monitoring （SHM） field.展开更多
A basic method to calculate van der Waals dispersion force distributions for submicron superquadric particles in particle-wall systems is presented. The force distribution is achieved by rotating particles through a l...A basic method to calculate van der Waals dispersion force distributions for submicron superquadric particles in particle-wall systems is presented. The force distribution is achieved by rotating particles through a large number of arbitrary spatial orientations, each time keeping constant the contact distance to the wall surface while calculating the dispersion force. To accomplish this, the use of 2D particle shape suffices, that is, through using an inter-dimensional function, which has been determined previously. A further development of the method within digital image analysis may lead to possible applications to forecasting the macroscopic properties of particle systems, for example, flowability, agglomeration behavior or dispersibility. For small ranges of superquadric particle shapes, each with a different size, the way from determining the inter-dimensional function up to applying image analysis is shown in an example.展开更多
为了进一步研究I S O-8 3 4标准火灾作用下三面受火带楼板钢筋混凝土T形梁的温度场分布,采用A B A Q U S非线性有限元软件建立带楼板钢筋混凝土T形梁的温度场分析模型,在此基础上,在不同T形梁截面尺寸和高宽比等情况下,对考虑升、降温...为了进一步研究I S O-8 3 4标准火灾作用下三面受火带楼板钢筋混凝土T形梁的温度场分布,采用A B A Q U S非线性有限元软件建立带楼板钢筋混凝土T形梁的温度场分析模型,在此基础上,在不同T形梁截面尺寸和高宽比等情况下,对考虑升、降温全过程的温度场和火灾后温度场分布进行研究。研究结果表明:楼板对钢筋混凝土梁的截面升温有较大影响,T梁腹板宽度影响相邻楼板的温度场分布;考虑升温和降温全过程后,内部混凝土达到最高温度的时间明显滞后,距离受火面越远,升温滞后越严重;火灾后的混凝土截面温度场分布与升温或降温过程中任一时刻的温度场有较大不同,进行火灾后钢筋混凝土T形梁的力学性能分析时,应采用火灾后(历史最高)温度场。展开更多
基金Indian Institute of Technology,Kharagpur in India for supporting this work
文摘Particle size distribution of coarse aggregates through mechanical sieving gives results in terms of cumu- lative mass percent. But digital image processing generated size distribution of particles, while being fast and accurate, is often expressed in terms of area function or number of particles. In this paper, a mass model is developed which converts the image obtained size distribution to mass-wise distribution, mak- ing it readily comparable to mechanical sieving data. The concept of weight/particle ratio is introduced for mass reconstruction from 2D images of particle aggregates. Using this mass model, the effects of several particle shape parameters （such as major axis, minor axis, and equivalent diameter） on sieve-size of the particles is studied. It is shown that the sieve-size of a particle strongly depend upon the shape param- eters, 91% of its variation being explained by major axis, minor axis, bounding box length and equivalent diameter. Furthermore, minor axis gives an overall accurate estimate of particle sieve-size, error in mean size （D-50） being just 0.4%. However, sieve-size of smaller particles （〈20 ram） strongly depends upon the length of the smaller arm of the bounding box enclosing them and sieve-sizes of larger particles （〉20 mm） are highly correlated to their equivalent diameters. Multiple linear regression analysis has been used to generate overall mass-wise particle size distribution, considering the influences of all these shape parameters on particle sieve-size. Multiple linear regression generated overall mass-wise particle size distribution shows a strong correlation with sieve generated data. The adjusted R-square value of the regression analysis is found to be 99 percent （w.r,t cumulative frequency）. The method proposed in this paper provides a time-efficient way of producing accurate （up to 99%） mass-wise PSD using digital image processing and it can be used effectively to renlace the mechanical sieving.
文摘This study explores the arrivals of water pipeline break failures. The aim is to assist the facility manager in the decision making process. Based on characteristics of the data set ranging from 2011 to 2014, two steps of analysis were presented in the paper. This first step is the analysis of partially complete data set (2011 data). The 2-sample KS test is adopted to check the similarity between this data set and the entire data set with no underlying distribution implied. In order to conduct the reliability analysis, the Weibull distribution is adopted to evaluate the data. For annual data set, the 2-parameter Weibull distribution fits data sets pretty well. The shape parameters are a little greater than 1, indicating a slightly increasing arrival rate of such failures. For the entire data set, the 3-parameter Weibull tends to fit the data better than the 2-parameter Weibull. The shape parameter is well above 1, indicating an increasing arrival rate of the failures. To eliminate the impact of missing points for the 2011 data set, data from 2012 to 2014 were also considered as a new set, the Weibull distribution generated a decent fitting. The shape parameter is a little greater than 1. Therefore, there is a slightly increasing arrival rate of those pipeline failures. Results from this study provide decision makers valuable information in terms of whether additional efforts shall be made to enhance the system’s performance in order to reduce the failure rate.
基金The National Natural Science Foudation of China(No.51578140)the Natural Science Foundation of Jiangsu Province(No.BK20151092)Scientific Innovation Research of College Graduates in Jiangsu Province(No.CXZZ12_0108)
文摘To develop modal macro-strain （ MMS ） identification techniques and improve their applicability in a continuous health monitoring system for civil infrastructures, the concept of operational macro-strain shape （OMSS） and the corresponding identification method are proposed under unknown ever-changing loading conditions, and the MMS is then obtained. The core of the proposed technique is mainly based on the specific property that the macro-strain transmissibility tends to be independent of external excitations at the poles of the system and converges to a unique value. The proposed method is verified using the experimental data from a three-span continuous beam excited by an impact hammer at different locations. The identified results are also compared with the commonly used methods, such as the peak- picking （PP） method, the stochastic subspace identification （SSI） method, and numerical results, in the case of unknown input forces. Results show that the proposed technique has unique merits in accuracy and robustness due to its combining multiple tests under changing loading conditions, which also reveal the promising application of the distributed strain sensing system in identifying MMS of operational structures, as well as in the structural health monitoring （SHM） field.
文摘A basic method to calculate van der Waals dispersion force distributions for submicron superquadric particles in particle-wall systems is presented. The force distribution is achieved by rotating particles through a large number of arbitrary spatial orientations, each time keeping constant the contact distance to the wall surface while calculating the dispersion force. To accomplish this, the use of 2D particle shape suffices, that is, through using an inter-dimensional function, which has been determined previously. A further development of the method within digital image analysis may lead to possible applications to forecasting the macroscopic properties of particle systems, for example, flowability, agglomeration behavior or dispersibility. For small ranges of superquadric particle shapes, each with a different size, the way from determining the inter-dimensional function up to applying image analysis is shown in an example.
文摘为了进一步研究I S O-8 3 4标准火灾作用下三面受火带楼板钢筋混凝土T形梁的温度场分布,采用A B A Q U S非线性有限元软件建立带楼板钢筋混凝土T形梁的温度场分析模型,在此基础上,在不同T形梁截面尺寸和高宽比等情况下,对考虑升、降温全过程的温度场和火灾后温度场分布进行研究。研究结果表明:楼板对钢筋混凝土梁的截面升温有较大影响,T梁腹板宽度影响相邻楼板的温度场分布;考虑升温和降温全过程后,内部混凝土达到最高温度的时间明显滞后,距离受火面越远,升温滞后越严重;火灾后的混凝土截面温度场分布与升温或降温过程中任一时刻的温度场有较大不同,进行火灾后钢筋混凝土T形梁的力学性能分析时,应采用火灾后(历史最高)温度场。
