A new steel matrix wear resistant composite reinforced by in situ granular eutectics can be obtained by modifying with a Si-Ce-Ti compound in the steel melt. The result indicates that the in situ granular eutectic is...A new steel matrix wear resistant composite reinforced by in situ granular eutectics can be obtained by modifying with a Si-Ce-Ti compound in the steel melt. The result indicates that the in situ granular eutectic is a pseudo-eutectic of austenite and (Fe,Mn)3C, which is formed between austenite dendrites during solidification due to the segregation of C and Mn impelled by modifying elements. The quantity of in situ granular eutectic reaches up to 8%-12% and its grain size is in the range from 10um to 20um. The austenite steel matrix wear resistant composite reinforced by in situ granular eutectic (abbreviated AGE composite) and austenite-bainite steel mains wear resistant composite reinforced by in situ granular eutectic (abbreviated ABGE composite) are obtained in the as-cast state and by air hardening, respectively. The wear resistance of the AGE and ABGE composites can be more greatly increased than that of their matrix steels under low and medium impact working condition.展开更多
In this paper, the microstructural evolution, grain refinement and mechanical properties of as-cast Mg-6Zn-0.4Zr alloys with varying Sm contents（0, 2 wt.%, 4 wt.% and 6 wt.%） were investigated by using an optical mi...In this paper, the microstructural evolution, grain refinement and mechanical properties of as-cast Mg-6Zn-0.4Zr alloys with varying Sm contents（0, 2 wt.%, 4 wt.% and 6 wt.%） were investigated by using an optical microscope（OM）, a scanning electron microscope（SEM） equipped with energy dispersive spectroscope（EDS）, an X-ray diffractometer（XRD） and mechanical tests at room temperature, respectively. The experimental results indicated that the addition of Sm could obviously refine the as-cast grains, modify the eutectic morphology and affect the mechanical properties of the alloys. The main phases in Mg-6Zn-xSm-0.4Zr alloys included matrix α-Mg, Mg2Zn3, Mg（41）Sm5 and MgZ nS m. With Sm content increasing to 4%, the MgZ nS m phase was created, meanwhile, the morphology of some eutectic phases revealed apparently lamellar structure, which had a bad effect on the mechanical properties. In addition, the maximum values of ultimate tensile strength（UTS, 214 MPa） and elongation（EL, 7.42%） were simultaneously obtained from the alloy with 2% Sm. However, Sm addition had no obvious effects on the fracture behavior of the alloys, namely, the fracture pattern of Mg-6Zn-0.4Zr alloy belonged to inter-granular and brittle modes while the fracture regimes of all the Sm-containing alloys were dominated by the mixture of inter-granular and trans-granular modes.展开更多
基金Acknowledgements - This project was supported by the National Natural Science Foundation of China (Grant No.50001008).
文摘A new steel matrix wear resistant composite reinforced by in situ granular eutectics can be obtained by modifying with a Si-Ce-Ti compound in the steel melt. The result indicates that the in situ granular eutectic is a pseudo-eutectic of austenite and (Fe,Mn)3C, which is formed between austenite dendrites during solidification due to the segregation of C and Mn impelled by modifying elements. The quantity of in situ granular eutectic reaches up to 8%-12% and its grain size is in the range from 10um to 20um. The austenite steel matrix wear resistant composite reinforced by in situ granular eutectic (abbreviated AGE composite) and austenite-bainite steel mains wear resistant composite reinforced by in situ granular eutectic (abbreviated ABGE composite) are obtained in the as-cast state and by air hardening, respectively. The wear resistance of the AGE and ABGE composites can be more greatly increased than that of their matrix steels under low and medium impact working condition.
基金Project supported by the National Nature Science Foundations of China(51464032)the National Basic Research Program of China(2010CB635106)
文摘In this paper, the microstructural evolution, grain refinement and mechanical properties of as-cast Mg-6Zn-0.4Zr alloys with varying Sm contents（0, 2 wt.%, 4 wt.% and 6 wt.%） were investigated by using an optical microscope（OM）, a scanning electron microscope（SEM） equipped with energy dispersive spectroscope（EDS）, an X-ray diffractometer（XRD） and mechanical tests at room temperature, respectively. The experimental results indicated that the addition of Sm could obviously refine the as-cast grains, modify the eutectic morphology and affect the mechanical properties of the alloys. The main phases in Mg-6Zn-xSm-0.4Zr alloys included matrix α-Mg, Mg2Zn3, Mg（41）Sm5 and MgZ nS m. With Sm content increasing to 4%, the MgZ nS m phase was created, meanwhile, the morphology of some eutectic phases revealed apparently lamellar structure, which had a bad effect on the mechanical properties. In addition, the maximum values of ultimate tensile strength（UTS, 214 MPa） and elongation（EL, 7.42%） were simultaneously obtained from the alloy with 2% Sm. However, Sm addition had no obvious effects on the fracture behavior of the alloys, namely, the fracture pattern of Mg-6Zn-0.4Zr alloy belonged to inter-granular and brittle modes while the fracture regimes of all the Sm-containing alloys were dominated by the mixture of inter-granular and trans-granular modes.
