Trend forecasting is an important aspect in fault diagnosis and work state supervision. The principle, where Grey theory is applied in fault forecasting, is that the forecast system is considered as a Grey system; the...Trend forecasting is an important aspect in fault diagnosis and work state supervision. The principle, where Grey theory is applied in fault forecasting, is that the forecast system is considered as a Grey system; the existing known information is used to infer the unknown information's character, state and development trend in a fault pattern, and to make possible forecasting and decisions for future development. It involves the whitenization of a Grey process. But the traditional equal time interval Grey GM (1,1) model requires equal interval data and needs to bring about accumulating addition generation and reversion calculations. Its calculation is very complex. However, the non equal interval Grey GM (1,1) model decreases the condition of the primitive data when establishing a model, but its requirement is still higher and the data were pre processed. The abrasion primitive data of plant could not always satisfy these modeling requirements. Therefore, it establishes a division method suited for general data modeling and estimating parameters of GM (1,1), the standard error coefficient that was applied to judge accuracy height of the model was put forward; further, the function transform to forecast plant abrasion trend and assess GM (1,1) parameter was established. These two models need not pre process the primitive data. It is not only suited for equal interval data modeling, but also for non equal interval data modeling. Its calculation is simple and convenient to use. The oil spectrum analysis acted as an example. The two GM (1,1) models put forward in this paper and the new information model and its comprehensive usage were investigated. The example shows that the two models are simple and practical, and worth expanding and applying in plant fault diagnosis.展开更多
The major advantage of grey system theory is that both incomplete information and unclear problems can be processed precisely. Considering that the modeling of grey model(GM) depends on the preprocessing of the origin...The major advantage of grey system theory is that both incomplete information and unclear problems can be processed precisely. Considering that the modeling of grey model(GM) depends on the preprocessing of the original data,the fractional-order accumulation calculus could be used to do preprocessing. In this paper, the residual sequence represented by Fourier series is used to ameliorate performance of the fractionalorder accumulation GM(1,1) and improve the accuracy of predictor. The state space model of optimally modified GM(1,1)predictor is given and genetic algorithm(GA) is used to find the smallest relative error during the modeling step. Furthermore,the fractional form of continuous GM(1,1) is given to enlarge the content of prediction model. The simulation results illustrated that the fractional-order calculus could be used to depict the GM precisely with more degrees of freedom. Meanwhile, the ranges of the parameters and model application could be enlarged with better performance. The method of modified GM predictor using optimal fractional-order accumulation calculus is expected to be widely used in data processing, model theory, prediction control and related fields.展开更多
he Grey system theory -was applied in reliability analysis of mechanical equip-ment. It is a new theory and method in reliability engineering of mechanical engineering of mechanical equipment. Through the Grey forecas...he Grey system theory -was applied in reliability analysis of mechanical equip-ment. It is a new theory and method in reliability engineering of mechanical engineering of mechanical equipment. Through the Grey forecast of reliability parameters and the reliability forecast of parts and systems, decisions were made in the real operative state of e-quipment in real time. It replaced the old method that required mathematics and physical statistics in a large base of test data to obtain a pre-check , and it was used in a practical problem. Because of applying the data of practical operation state in real time, it could much more approach the real condition of equipment; it-was applied to guide the procedure and had rather considerable economic and social benefits.展开更多
Three forecasting models are set up: the auto\|regressive moving average model, the grey forecasting model for the rate of qualified products P t, and the grey forecasting model for time intervals of the quality cata...Three forecasting models are set up: the auto\|regressive moving average model, the grey forecasting model for the rate of qualified products P t, and the grey forecasting model for time intervals of the quality catastrophes. Then a combined forewarning system for the quality of products is established, which contains three models, judgment rules and forewarning state illustration. Finally with an example of the practical production, this modeling system is proved fairly effective.展开更多
The grey model (GM) can be used to predict the future data. But sometimes, the precision of forecasted value is not satisfactorys In order to improve the precision of the grey model and make the forecasting result mor...The grey model (GM) can be used to predict the future data. But sometimes, the precision of forecasted value is not satisfactorys In order to improve the precision of the grey model and make the forecasting result more accurate and rational, this paper presents a new method which is called the minimum method (mini-method). It’s principle is first introduced, and it is demonstrated by an example. Finally, the effectiveness of the new method is verified with the grey relational degree (GRD).展开更多
The extended “STIRPAT” model and the GM(1,1) model are used to predict the factors influencing inter-provincial carbon emission intensity and carbon intensity in China respectively. In this paper, based on the colla...The extended “STIRPAT” model and the GM(1,1) model are used to predict the factors influencing inter-provincial carbon emission intensity and carbon intensity in China respectively. In this paper, based on the collation of inter-provincial carbon emission data, the extended “STIRPAT” model is formulated for carbon dioxide emissions and carbon intensity emissions, and the Hausman test is used to determine the influence form of the models. The main influencing factors of carbon intensity were identified: economic development level, energy intensity, and energy consumption structure. The paper constructs GM(1,1) model for carbon emission intensity from 2010-2019 using the gray prediction method,and calculates the carbon emission intensity of China’s inter-provincial 2022 by residual test, correlation test, variance, and small error probability test, and then predicts the carbon demand of each province and city in 2022 according to the expected average annual growth rate, and finally concludes that using carbon emission intensity as the carbon emission reduction target of each region, and it cannot fundamentally solve the problem of carbon pollution in China. Compared to the regional carbon emission reduction target, there is a greater degree of regional imbalance in carbon intensity between provinces in China, and the target of reducing carbon emission intensity somehow avoids the fact that the carbon emission reduction intensity target can be achieved without reducing the absolute amount of carbon emissions that continue to increase. The focus of achieving the “double carbon” target lies in the reduction of total carbon emissions, and the target of reducing carbon intensity will eventually be transformed into a binding target of total carbon emissions in the process of implementation, so attention should be shifted from recessiontype carbon reduction and efficiency-type carbon reduction to innovative carbon reduction. It is necessary to increase investment in renewable energy, and gradually expand the scope of application of photovoltaic, and wind power to ensure the reduction of total carbon emissions.展开更多
文摘Trend forecasting is an important aspect in fault diagnosis and work state supervision. The principle, where Grey theory is applied in fault forecasting, is that the forecast system is considered as a Grey system; the existing known information is used to infer the unknown information's character, state and development trend in a fault pattern, and to make possible forecasting and decisions for future development. It involves the whitenization of a Grey process. But the traditional equal time interval Grey GM (1,1) model requires equal interval data and needs to bring about accumulating addition generation and reversion calculations. Its calculation is very complex. However, the non equal interval Grey GM (1,1) model decreases the condition of the primitive data when establishing a model, but its requirement is still higher and the data were pre processed. The abrasion primitive data of plant could not always satisfy these modeling requirements. Therefore, it establishes a division method suited for general data modeling and estimating parameters of GM (1,1), the standard error coefficient that was applied to judge accuracy height of the model was put forward; further, the function transform to forecast plant abrasion trend and assess GM (1,1) parameter was established. These two models need not pre process the primitive data. It is not only suited for equal interval data modeling, but also for non equal interval data modeling. Its calculation is simple and convenient to use. The oil spectrum analysis acted as an example. The two GM (1,1) models put forward in this paper and the new information model and its comprehensive usage were investigated. The example shows that the two models are simple and practical, and worth expanding and applying in plant fault diagnosis.
基金supported by the National Natural Science Foundation of China(61174145)
文摘The major advantage of grey system theory is that both incomplete information and unclear problems can be processed precisely. Considering that the modeling of grey model(GM) depends on the preprocessing of the original data,the fractional-order accumulation calculus could be used to do preprocessing. In this paper, the residual sequence represented by Fourier series is used to ameliorate performance of the fractionalorder accumulation GM(1,1) and improve the accuracy of predictor. The state space model of optimally modified GM(1,1)predictor is given and genetic algorithm(GA) is used to find the smallest relative error during the modeling step. Furthermore,the fractional form of continuous GM(1,1) is given to enlarge the content of prediction model. The simulation results illustrated that the fractional-order calculus could be used to depict the GM precisely with more degrees of freedom. Meanwhile, the ranges of the parameters and model application could be enlarged with better performance. The method of modified GM predictor using optimal fractional-order accumulation calculus is expected to be widely used in data processing, model theory, prediction control and related fields.
文摘he Grey system theory -was applied in reliability analysis of mechanical equip-ment. It is a new theory and method in reliability engineering of mechanical engineering of mechanical equipment. Through the Grey forecast of reliability parameters and the reliability forecast of parts and systems, decisions were made in the real operative state of e-quipment in real time. It replaced the old method that required mathematics and physical statistics in a large base of test data to obtain a pre-check , and it was used in a practical problem. Because of applying the data of practical operation state in real time, it could much more approach the real condition of equipment; it-was applied to guide the procedure and had rather considerable economic and social benefits.
文摘Three forecasting models are set up: the auto\|regressive moving average model, the grey forecasting model for the rate of qualified products P t, and the grey forecasting model for time intervals of the quality catastrophes. Then a combined forewarning system for the quality of products is established, which contains three models, judgment rules and forewarning state illustration. Finally with an example of the practical production, this modeling system is proved fairly effective.
文摘The grey model (GM) can be used to predict the future data. But sometimes, the precision of forecasted value is not satisfactorys In order to improve the precision of the grey model and make the forecasting result more accurate and rational, this paper presents a new method which is called the minimum method (mini-method). It’s principle is first introduced, and it is demonstrated by an example. Finally, the effectiveness of the new method is verified with the grey relational degree (GRD).
文摘The extended “STIRPAT” model and the GM(1,1) model are used to predict the factors influencing inter-provincial carbon emission intensity and carbon intensity in China respectively. In this paper, based on the collation of inter-provincial carbon emission data, the extended “STIRPAT” model is formulated for carbon dioxide emissions and carbon intensity emissions, and the Hausman test is used to determine the influence form of the models. The main influencing factors of carbon intensity were identified: economic development level, energy intensity, and energy consumption structure. The paper constructs GM(1,1) model for carbon emission intensity from 2010-2019 using the gray prediction method,and calculates the carbon emission intensity of China’s inter-provincial 2022 by residual test, correlation test, variance, and small error probability test, and then predicts the carbon demand of each province and city in 2022 according to the expected average annual growth rate, and finally concludes that using carbon emission intensity as the carbon emission reduction target of each region, and it cannot fundamentally solve the problem of carbon pollution in China. Compared to the regional carbon emission reduction target, there is a greater degree of regional imbalance in carbon intensity between provinces in China, and the target of reducing carbon emission intensity somehow avoids the fact that the carbon emission reduction intensity target can be achieved without reducing the absolute amount of carbon emissions that continue to increase. The focus of achieving the “double carbon” target lies in the reduction of total carbon emissions, and the target of reducing carbon intensity will eventually be transformed into a binding target of total carbon emissions in the process of implementation, so attention should be shifted from recessiontype carbon reduction and efficiency-type carbon reduction to innovative carbon reduction. It is necessary to increase investment in renewable energy, and gradually expand the scope of application of photovoltaic, and wind power to ensure the reduction of total carbon emissions.
