There is a growing need to explore the potential of coal-fired power plants(CFPPs)to enhance the utilization rate of wind power(wind)and photovoltaic power(PV)in the green energy field.This study developed a load regu...There is a growing need to explore the potential of coal-fired power plants(CFPPs)to enhance the utilization rate of wind power(wind)and photovoltaic power(PV)in the green energy field.This study developed a load regulation model for a multi-power generation system comprising wind,PV,and coal energy storage using realworld data.The power supply process was divided into eight fundamental load regulation scenarios,elucidating the influence of each scenario on load regulation.Within the framework of the multi-power generation system with the wind(50 MW)and PV(50 MW)alongside a CFPP(330 MW),a lithium-iron phosphate energy storage system(LIPBESS)was integrated to improve the system’s load regulation flexibility.The energy storage operation strategy was formulated based on the charging and discharging priority of the LIPBESS for each basic scenario and the charging and discharging load calculation method of LIPBESS auxiliary regulation.Through optimization using the particle swarm algorithm,the optimal capacity of LIPBESS was determined to be within the 5.24-4.88 MWh range.From an economic perspective,the LIPBESS operating with CFPP as the regulating power source was 49.1% lower in capacity compared to the renewable energy-based storage mode.展开更多
To effectively quantify the impact of distributed photovoltaic(PV)access on the distribution network,this paper proposes a comprehensive evaluation method of distributed PV grid connection combining subjective and obj...To effectively quantify the impact of distributed photovoltaic(PV)access on the distribution network,this paper proposes a comprehensive evaluation method of distributed PV grid connection combining subjective and objective combination of assignment and technique for order preference by similarity to an ideal solution(TOPSIS)—rank sum ratio(RSR)(TOPSIS-RSR)method.Based on the traditional distribution network evaluation system,a comprehensive evaluation system has been constructed.It fully considers the new development requirements of distributed PV access on the environmental friendliness and absorptive capacity of the distribution grid and comprehensively reflects the impact of distributed PV grid connection.The analytic hierarchy process(AHP)was used to determine the subjective weights of the primary indicators,and the Spearman consistency test was combined to determine the weights of the secondary indicators based on three objective assignment methods.The subjective and objective combination weights of each assessment indicator were calculated through the principle of minimum entropy.Calculate the distance between the indicators to be evaluated and the positive and negative ideal solutions,the relative closeness ranking,and qualitative binning by TOPSIS-RSR method to obtain the comprehensive evaluation results of different scenarios.By setting up different PV grid-connected scenarios and utilizing the IEEE33 node simulation algorithm,the correctness and effectiveness of the proposed subject-object combination assignment and integrated assessment method are verified.展开更多
Standalone Solar PV systems have been vital in the improvement of access to energy in many countries.However,given the large cost of solar PV plants’components,in developing countries,there is a dear need for such co...Standalone Solar PV systems have been vital in the improvement of access to energy in many countries.However,given the large cost of solar PV plants’components,in developing countries,there is a dear need for such components to be subsidised and incentivised for the consumers to afford the produced energy.Moreover,there is a need for optimal sizing of the solar PV plants taking into account the solar information,energy requirement for various activities,and economic conditions in the off-grid regions in Rwanda.This study aims to develop optimally sized solar PV plants suited to rural communities in Rwanda.Likewise,it aims at characterizing the impacts of subsidies and incentives on the profitability and affordability of solar PV plants’energy in Rwanda.In the study,we have developed a model on basis of which the plant power(peak power)and costs of energy can be predicted given the load requirements using PVSyst.The model was validated using data corrected at eight different sites.Our generalized predictive model’s results matched the results obtained using field measurement data as inputs.The models have been able to replicate with a by degree of accuracy the peak powers and the plants’costs for different loads and were used to evaluate the economic viability of solar PV plants in Rwanda.It was found that with incentives and subsidies of 20%,the solar PV systems’costs,the Levelised Cost of Energy would drop from a maximum of 0.098 Euro to a minimum of 0.072 Euro,the payback period was reduced from a maximum of 7.5 years to a minimum of 6.0 years while the return on investments was seen to vary between 425.72 and 615.32 per cent over the plants’lifetime of 25 years.Overall our findings underscore the importance of government subsidies and incentives for solar PV energy generation projects to be significantly profitable.展开更多
The generation of photovoltaic(PV)solar energy is increasing continuously because it is renewable,unlimited,and clean energy.In the past,generation systems depended on non-renewable sources such as oil,coal,and gas.Th...The generation of photovoltaic(PV)solar energy is increasing continuously because it is renewable,unlimited,and clean energy.In the past,generation systems depended on non-renewable sources such as oil,coal,and gas.Therefore,this paper assesses the performance of a 51 kW PV solar power plant connected to a low-voltage grid to feed an administrative building in the 6th of October City,Egypt.The performance analysis of the considered grid-connected PV system is carried out using power system simulator for Engineering(PSS/E)software.Where the PSS/E program,monitors and uses the power analyzer that displays the parameters and measures some parameters such as current,voltage,total power,power factor,frequency,and current and voltage harmonics,the used inverter from the type of grid inverter for the considered system.The results conclude that when the maximum solar radiation is reached,the maximum current can be obtained from the solar panels,thus obtaining the maximum power and power factor.Decreasing total voltage harmonic distortion,a current harmonic distortion within permissible limits using active harmonic distortion because this type is fast in processing up to 300 microseconds.The connection between solar stations and the national grid makes the system more efficient.展开更多
The application of PV faades emerges greatly in recent years and however its calculation methods and analysis remains insufficient under the weather conditions of China. In such demand,this paper investigates PV fa...The application of PV faades emerges greatly in recent years and however its calculation methods and analysis remains insufficient under the weather conditions of China. In such demand,this paper investigates PV faade in terms of PV electricity generation in different arrangements and weather conditions of four major cities in China. The calculation models for PV faade are developed and validated by comparing the results with the measured data from the field experiments. A parametric study is carried out to provide a reference for the optimal design of the PV faades. The results show that with various cities,building orientations,building forms,materials and arrangements of PV modules,there is a distinct difference in the electrical output energy of PV faades. Weather conditions play a very important role in terms of PV generation performance of PV faades.展开更多
Being photovoltaic power generation affected by radiation strength, wind speed, clouds cover and environment temperature, the generating in each moment is fluctuating. The operational characteristics of grid-connected...Being photovoltaic power generation affected by radiation strength, wind speed, clouds cover and environment temperature, the generating in each moment is fluctuating. The operational characteristics of grid-connected PV systems are coincided with gray theory application conditions. A gray theory model has been applied in short-term forecast of grid-connected photovoltaic system. The verification model of the probability of small error will help to check the accuracy of the gray forecast results. The calculated result shows that the ?model accuracy has been greatly enhanced.展开更多
The complexity of distribution network model mainly depends on the model scale of grid-connected distributed photovoltaic (PV) power generation. Therefore, the simulation performance of multi-scale PV model is the key...The complexity of distribution network model mainly depends on the model scale of grid-connected distributed photovoltaic (PV) power generation. Therefore, the simulation performance of multi-scale PV model is the key factor of the simulation accuracy in the specific operating scenarios of distribution network. In this paper, a multi-scale model of grid connected PV distributed generation system is proposed based on the mathematical model of grid-connected distributed PV power generation. It is analyzed that differences of simulation performance, such as adaptability of simulation step size, accuracy of output and the effect on voltage profile of distribution network, between PV models with different scales in IEEE 33 node example. Simulation results indicate that the multi-scale model is effective in improving the accuracy and efficiency of simulation under different operating conditions of distribution network.展开更多
Nowadays, renewable energy resources play an important role in replacing conventional energy resources such as fossil fuel by integrating solar, wind and geothermal energy. Photovoltaic energy is one?of?the very promi...Nowadays, renewable energy resources play an important role in replacing conventional energy resources such as fossil fuel by integrating solar, wind and geothermal energy. Photovoltaic energy is one?of?the very promising renewable energy resources which grew rapidly in the past few years, it can be used to produce electric energy through photovoltaic process. The primary objective of the research proposed in this paper is to facilitate the increasing penetration levels of PV systems in the electric distribution networks. In this work, the PV module electrical model is presented based on the mathematical equations and was implemented on MATLAB to simulate the non-linear characteristics I-V and P-V curves with variable input parameters which are irradiance and temperature based on Riyadh region. In addition, the reliability evaluation of distribution networks, including distributed generators of solar photovoltaic (PV) with varying output power capacity is presented also. The Monte Carlo simulation algorithm is applied to test the distribution network which is RBTS Bus 2 and the same has been conducted on the original case of distribution network substation 7029 which is located at KSA Riyadh. The two distribution networks have been modified to include the PV’s distributed generators. The distributed generators contribute to supply a part of the load during normal mode and supply the entire load during component failure or failure of grid operation supply. The PV stochastic models have been used to simulate the randomness of these resources. Moreover, the study shows that the implementation and integration of renewable resources as distributed generations have improved the reliability of the distribution networks.展开更多
Integration of Solar Photovoltaic (PV) generation into an existing distribution system has many impacts on the system, with the power flow being one of the major issues. This impact is not generic for any network, but...Integration of Solar Photovoltaic (PV) generation into an existing distribution system has many impacts on the system, with the power flow being one of the major issues. This impact is not generic for any network, but it may manifest itself either positively or negatively, depending on the grid configuration, interface control modes, operation mode, and load profile. Grid-connected PV systems have three control options of the local voltage controller of the interface DC-AC converter. These control modes are Power Factor control, voltage control, and Droop Voltage control. This paper aims at evaluating and comparing the impacts of those control modes on the grid power flow. A set of evaluation criteria and indices is defined and mathematically formulated. Based on the requirements of the used program (Power Factory Dig Silent V14.1.3), a computation plan (algorithm) has been proposed. The algorithm has been applied to a typical weak network and a wide range of simulations has been carried out. Simulation results have been thoroughly discussed and important findings have been concluded.展开更多
The rapid spreading of the Photovoltaic (PV) Systems as Distributed Generation (DG) in medium and low voltage networks created many effects and changes on the existing power system networks. In this work, two methods ...The rapid spreading of the Photovoltaic (PV) Systems as Distributed Generation (DG) in medium and low voltage networks created many effects and changes on the existing power system networks. In this work, two methods have been used and applied to determine the optimal allocation and sizing of the PV to be installed as DGs (ranging from 250 kW up to 3 MW). The first one is to determine the location according to the maximal power losses reduction over the feeder. The second one is by using the Harmony Search Algorithm which is claimed to be a powerful technique for optimal allocation of PV systems. The results of the two techniques were compared and found to be nearly closed. Furthermore, investigation on the effects on the feeder in terms of voltage levels, power factor readings, and short circuit current levels has been done. All calculations and simulations are conducted by using the MATLAB Simulation Program. Some field calculations and observations have been expended in order to substantiate the research findings and validation.展开更多
A massive plan has been drawn by the Karnataka state of India to initiate several solar power plants at different locations. In view of this, it is of great help to have reliable estimation on solar PV energy generati...A massive plan has been drawn by the Karnataka state of India to initiate several solar power plants at different locations. In view of this, it is of great help to have reliable estimation on solar PV energy generation. Four solar PV power plants in Karnataka state are fully operational installed by Karnataka Power Corporation Limited (KPCL). They are located at Kolar, Belgaum and Raichur with 3 MW capacity each and at Mandya with 5 MW capacity. In the present study, using ground mounted weather station data solar power generation has been estimated and compared with actual generation for two consecutive years of 2012 and 2013 for one location initially, namely 3 MW Kolar Solar PV Plant. The procedure is repeated for rest of the plants. The simulated results have been corrected with ground mounted weather data. After such corrections, the simulated results have been compared with the actual energy generation of the four plants. Results showed a close match with a small deviation of about 5%. The model then applied throughout the state for every 0.25 degree station intervals in a grid manner. The annual energy generation obtained for the state varies from 1.53 to 1.73 MUs/MW. Central and south eastern part of the state are found to yield significantly higher solar power generation as compared to the northern part and south western part of Karnataka. Interestingly, north western part of Kodagu district has shown the least potential of 1.53 MUs/MW as compared to other parts. This can be attributed mainly due to low irradiation and high temperature condition at this location. The energy generated map from our study will be useful and helpful for both solar developers and decision makers of Karnataka state.展开更多
As wind and photovoltaic energy become more prevalent,the optimization of power systems is becoming increasingly crucial.The current state of research in renewable generation and power forecasting technology,such as w...As wind and photovoltaic energy become more prevalent,the optimization of power systems is becoming increasingly crucial.The current state of research in renewable generation and power forecasting technology,such as wind and photovoltaic power(PV),is described in this paper,with a focus on the ensemble sequential LSTMs approach with optimized hidden-layers topology for short-term multivariable wind power forecasting.The methods for forecasting wind power and PV production.The physical model,statistical learningmethod,andmachine learning approaches based on historical data are all evaluated for the forecasting of wind power and PV production.Moreover,the experiments demonstrated that cloud map identification has a significant impact on PV generation.With a focus on the impact of photovoltaic and wind power generation systems on power grid operation and its causes,this paper summarizes the classification of wind power and PV generation systems,as well as the benefits and drawbacks of PV systems and wind power forecasting methods based on various typologies and analysis methods.展开更多
Because of system constraints caused by the external environment and grid faults,the conventional maximum power point tracking(MPPT)and inverter control methods of a PV power generation system cannot achieve optimal p...Because of system constraints caused by the external environment and grid faults,the conventional maximum power point tracking(MPPT)and inverter control methods of a PV power generation system cannot achieve optimal power output.They can also lead to misjudgments and poor dynamic performance.To address these issues,this paper proposes a new MPPT method of PV modules based on model predictive control(MPC)and a finite control set model predictive current control(FCS-MPCC)of an inverter.Using the identification model of PV arrays,the module-based MPC controller is designed,and maximum output power is achieved by coordinating the optimal combination of spectral wavelength and module temperature.An FCS-MPCC algorithm is then designed to predict the inverter current under different voltage vectors,the optimal voltage vector is selected according to the optimal value function,and the corresponding optimal switching state is applied to power semiconductor devices of the inverter.The MPPT performance of the MPC controller and the responses of the inverter under different constraints are verified,and the steady-state and dynamic control effects of the inverter using FCS-MPCC are compared with the traditional feedforward decoupling PI control in Matlab/Simulink.The results show that MPC has better tracking performance under constraints,and the system has faster and more accurate dynamic response and flexibility than conventional PI control.展开更多
This document presents the evaluation and the monitoring of the performances of the first grid-connected photovoltaic system installed in the Center of Studies and Researches on the Renewable Energies (CERER) inaugura...This document presents the evaluation and the monitoring of the performances of the first grid-connected photovoltaic system installed in the Center of Studies and Researches on the Renewable Energies (CERER) inaugurated on December 4th, 2012 by the governmental authorities of Senegal and Tenerife. This mini power plant of 3.15 kWc is a perfect example of the political will of the government which is to reduce the production cost of the electricity, with the diversification of the sources of production, and the greater use of the other sources such as the natural gas, the coal, the renewable energies. The evaluation of the performances of the installation is realized by using the indicators of efficiency and performance as the photovoltaic surface yield, the ratio of photovoltaic performance, the photovoltaic specific yield, and the losses of captures. The obtained results show that a big part of the energy shone during the period of observation was not able to be used further to circumstances such as the losses of conductivity, the heat losses or for example the defects on components. The analysis also shows that a large part of the produced energy is not injected because of the dilapidation of the network, the defects of landing but especially one disjunction sees frequently at the level of the point of injection.展开更多
This paper primarily discusses the main circuit of single-phase inverter circuits.It begins by introducing the research context and the significance of the subject,then discusses the topology of grid-connected single-...This paper primarily discusses the main circuit of single-phase inverter circuits.It begins by introducing the research context and the significance of the subject,then discusses the topology of grid-connected single-phase inverter circuits,continues by discussing the control strategy for grid-connected single-phase inverter circuits,realizes a sinusoidal pulse width modulation(SPWM)signal generation circuit and an inverse control algorithm program,and finally ensures good output waveform and fast dynamic response.In view of the hysteresis feature of the grid voltage’s synchronous signal sampling circuit,the acquisition function in digital signal processing(DSP)control chips is applied,and the reasons for the hysteresis phenomenon are thoroughly investigated.The reliability of the SPWM control algorithm is revealed through the results.展开更多
Solar energy has been widely used in power generation.With the development of solar energy,the distributed photovoltaic power generation and the distributed grid-connected PV systems become the center of attention.Thi...Solar energy has been widely used in power generation.With the development of solar energy,the distributed photovoltaic power generation and the distributed grid-connected PV systems become the center of attention.This paper provided a brief introduction to distribution-level solar energy.Firstly,the development of solar energy was analyzed,and the distributed photovoltaic power generation was discussed.Secondly,the distributed grid-connected PV systems and basic theory of photovoltaic solar channel were analyzed.In order to ensure PV power is connected to grid stably and reliably,some related aspects such as the establishment of mathematical model for solar photovoltaic cell,the analysis of I-V characteristics of solar photovoltaic cell,and the tracking of its maximum power point(MPPT)to control the behaviour of the DC/DC converter were discussed.Finally,a simulation model was necessary to be established by using PSCAD/EMTDC function module to verify and simulate the mathematical model and control strategies,and some suggestions were put forward for the sustainable development of solar energy.展开更多
This paper describes the research on a largescale dispatchable grid-connected photovoltaic(PV)system for supplying power to the grid for dispatch instead of supplying the electricity to a local load.In order to maximi...This paper describes the research on a largescale dispatchable grid-connected photovoltaic(PV)system for supplying power to the grid for dispatch instead of supplying the electricity to a local load.In order to maximise the value of the solar energy,a hybrid electricity storage consisting of batteries and supercapacitors is used with the PV system.This paper proposes a control strategy focusing on theDCpower at theDClink rather than at the grid-connected inverter.Two typical sets of real data,collected from existing sites,are used to demonstrate the practicality of the system.Finally,the simulation results are used to demonstrate the good performance and feasibility of the proposed system together with the proposed control strategy.展开更多
Impedance analysis is an effective method to analyze the oscillation issue associated with grid-connected photovoltaic systems.However,the existing impedance modeling of a gridconnected photovoltaic inverter usually o...Impedance analysis is an effective method to analyze the oscillation issue associated with grid-connected photovoltaic systems.However,the existing impedance modeling of a gridconnected photovoltaic inverter usually only considers the effect of a single perturbation frequency,ignoring the coupling frequency response between the internal control loops of a grid-connected inverter,which severely affects the accuracy of the stability analysis.Hence,a method of impedance modeling and stability analysis for grid-connected photovoltaic inverters considering cross-coupling frequency is proposed in this paper.First,the generation mechanism of frequency coupling in gridconnected photovoltaic inverters,and the relationship between the coupling frequency and perturbation frequency are analyzed.Secondly,a sequence impedance model of grid-connected photovoltaic systems considering the coupling frequency is established by using the harmonic linearization method.The impact of DC bus voltage control strategy on frequency coupling characteristics of a grid-connected photovoltaic system is evaluated,and the impact of a coupling frequency term on system stability is quantitatively analyzed.Finally,the advantages of the proposed method are verified by several simulations.The results show that the proposed impedance model can accurately predict the potential resonance points of the system,and the coupling frequency characteristics will become much stronger with smaller DC bus capacitance or larger bandwidth of the DC bus controller.展开更多
Buildings are responsible for over 40% of total primary energy consumption in the US and EU and therefore improving building energy efficiency has significant potential for obtaining net-zero energy buildings reducing...Buildings are responsible for over 40% of total primary energy consumption in the US and EU and therefore improving building energy efficiency has significant potential for obtaining net-zero energy buildings reducing energy consumption. The concurrent demands of environmental comfort and the need to improve energy efficiency for both new and existing buildings have motivated research into finding solutions for the regulation of incoming solar radiation, as well as ensuring occupant thermal and visual comfort whilst generating energy onsite. Windows as building components offer the opportunity of addressing these issues in buildings. Building integration of photovoltaics permits building components such as semi-transparent façade, skylights and shading devices to be replaced with PV. Much progress has been made in photovoltaic material science, where smart window development has evolved in areas such as semi-transparent PV, electrochromic and thermochromic materials, luminescent solar concentrator and the integration of each of the latter technologies to buildings, specifically windows. This paper presents a review on intelligent window technologies that integrate renewable energy technologies with energy-saving strategies contributing potential solutions towards sustainable zero-energy buildings. This review is a comprehensive evaluation of intelligent windows focusing on state-of-the-art development in windows that can generate electricity and their electrical, thermal and optical characteristics. This review provides a summary of current work in intelligent window design for energy generation and gives recommendations for further research opportunities.展开更多
Large-scale, grid-connected photovoltaic sys- tems have become an essential part of modem electric power distribution systems. In this paper, a novel approach based on the Markov method has been proposed to investigat...Large-scale, grid-connected photovoltaic sys- tems have become an essential part of modem electric power distribution systems. In this paper, a novel approach based on the Markov method has been proposed to investigate the effects of large-scale, grid-connected photovoltaic systems on the reliability of bulk power systems. The proposed method serves as an applicable tool to estimate performance (e.g., energy yield and capacity) as well as reliability indices. The Markov method frame- work has been incorporated with the' multi-state models to develop energy states of the photovoltaic systems in order to quantify the effects of the photovoltaic systems on the power system adequacy. Such analysis assists planners to make adequate decisions based on the economical expectations as well as to ensure the recovery of the investment costs over time. The failure states of the components of photovoltaic systems have been considered to evaluate the sensitivity analysis and the adequacy indices including loss of load expectation, and expected energy not supplied. Moreover, the impacts of transitions between failures on the reliability calculations as well as on the long- term operation of the photovoltaic systems have been illustrated. Simulation results on the Roy Billinton test system has been shown to illustrate the procedure of the proposed frame work and evaluate the reliability benefits of using large-scale, grid-connected photovoltaic system on the bulk electric power systems. The proposed method can be easily extended to estimate the operating and maintenance costs for the financial planning of the photovoltaic system projects.展开更多
基金supported by the Natural Science Foundation of China(Grant Nos.52076079,52206010)Natural Science Foundation of Hebei Province,China(Grant No.E2020502013)the Fundamental Research Funds for the Central Universities(2021MS076,2021MS079).
文摘There is a growing need to explore the potential of coal-fired power plants(CFPPs)to enhance the utilization rate of wind power(wind)and photovoltaic power(PV)in the green energy field.This study developed a load regulation model for a multi-power generation system comprising wind,PV,and coal energy storage using realworld data.The power supply process was divided into eight fundamental load regulation scenarios,elucidating the influence of each scenario on load regulation.Within the framework of the multi-power generation system with the wind(50 MW)and PV(50 MW)alongside a CFPP(330 MW),a lithium-iron phosphate energy storage system(LIPBESS)was integrated to improve the system’s load regulation flexibility.The energy storage operation strategy was formulated based on the charging and discharging priority of the LIPBESS for each basic scenario and the charging and discharging load calculation method of LIPBESS auxiliary regulation.Through optimization using the particle swarm algorithm,the optimal capacity of LIPBESS was determined to be within the 5.24-4.88 MWh range.From an economic perspective,the LIPBESS operating with CFPP as the regulating power source was 49.1% lower in capacity compared to the renewable energy-based storage mode.
基金support of the project“State Grid Corporation Headquarters Science and Technology Program(5108-202299258A-1-0-ZB)”.
文摘To effectively quantify the impact of distributed photovoltaic(PV)access on the distribution network,this paper proposes a comprehensive evaluation method of distributed PV grid connection combining subjective and objective combination of assignment and technique for order preference by similarity to an ideal solution(TOPSIS)—rank sum ratio(RSR)(TOPSIS-RSR)method.Based on the traditional distribution network evaluation system,a comprehensive evaluation system has been constructed.It fully considers the new development requirements of distributed PV access on the environmental friendliness and absorptive capacity of the distribution grid and comprehensively reflects the impact of distributed PV grid connection.The analytic hierarchy process(AHP)was used to determine the subjective weights of the primary indicators,and the Spearman consistency test was combined to determine the weights of the secondary indicators based on three objective assignment methods.The subjective and objective combination weights of each assessment indicator were calculated through the principle of minimum entropy.Calculate the distance between the indicators to be evaluated and the positive and negative ideal solutions,the relative closeness ranking,and qualitative binning by TOPSIS-RSR method to obtain the comprehensive evaluation results of different scenarios.By setting up different PV grid-connected scenarios and utilizing the IEEE33 node simulation algorithm,the correctness and effectiveness of the proposed subject-object combination assignment and integrated assessment method are verified.
文摘Standalone Solar PV systems have been vital in the improvement of access to energy in many countries.However,given the large cost of solar PV plants’components,in developing countries,there is a dear need for such components to be subsidised and incentivised for the consumers to afford the produced energy.Moreover,there is a need for optimal sizing of the solar PV plants taking into account the solar information,energy requirement for various activities,and economic conditions in the off-grid regions in Rwanda.This study aims to develop optimally sized solar PV plants suited to rural communities in Rwanda.Likewise,it aims at characterizing the impacts of subsidies and incentives on the profitability and affordability of solar PV plants’energy in Rwanda.In the study,we have developed a model on basis of which the plant power(peak power)and costs of energy can be predicted given the load requirements using PVSyst.The model was validated using data corrected at eight different sites.Our generalized predictive model’s results matched the results obtained using field measurement data as inputs.The models have been able to replicate with a by degree of accuracy the peak powers and the plants’costs for different loads and were used to evaluate the economic viability of solar PV plants in Rwanda.It was found that with incentives and subsidies of 20%,the solar PV systems’costs,the Levelised Cost of Energy would drop from a maximum of 0.098 Euro to a minimum of 0.072 Euro,the payback period was reduced from a maximum of 7.5 years to a minimum of 6.0 years while the return on investments was seen to vary between 425.72 and 615.32 per cent over the plants’lifetime of 25 years.Overall our findings underscore the importance of government subsidies and incentives for solar PV energy generation projects to be significantly profitable.
文摘The generation of photovoltaic(PV)solar energy is increasing continuously because it is renewable,unlimited,and clean energy.In the past,generation systems depended on non-renewable sources such as oil,coal,and gas.Therefore,this paper assesses the performance of a 51 kW PV solar power plant connected to a low-voltage grid to feed an administrative building in the 6th of October City,Egypt.The performance analysis of the considered grid-connected PV system is carried out using power system simulator for Engineering(PSS/E)software.Where the PSS/E program,monitors and uses the power analyzer that displays the parameters and measures some parameters such as current,voltage,total power,power factor,frequency,and current and voltage harmonics,the used inverter from the type of grid inverter for the considered system.The results conclude that when the maximum solar radiation is reached,the maximum current can be obtained from the solar panels,thus obtaining the maximum power and power factor.Decreasing total voltage harmonic distortion,a current harmonic distortion within permissible limits using active harmonic distortion because this type is fast in processing up to 300 microseconds.The connection between solar stations and the national grid makes the system more efficient.
基金Sponsored by the National Natural Science Foundation of China (Grant No.51008136)the Graduates’ Innovation and Enterprise Fund of HUST (Grant No.HF-11-12-2013)
文摘The application of PV faades emerges greatly in recent years and however its calculation methods and analysis remains insufficient under the weather conditions of China. In such demand,this paper investigates PV faade in terms of PV electricity generation in different arrangements and weather conditions of four major cities in China. The calculation models for PV faade are developed and validated by comparing the results with the measured data from the field experiments. A parametric study is carried out to provide a reference for the optimal design of the PV faades. The results show that with various cities,building orientations,building forms,materials and arrangements of PV modules,there is a distinct difference in the electrical output energy of PV faades. Weather conditions play a very important role in terms of PV generation performance of PV faades.
文摘Being photovoltaic power generation affected by radiation strength, wind speed, clouds cover and environment temperature, the generating in each moment is fluctuating. The operational characteristics of grid-connected PV systems are coincided with gray theory application conditions. A gray theory model has been applied in short-term forecast of grid-connected photovoltaic system. The verification model of the probability of small error will help to check the accuracy of the gray forecast results. The calculated result shows that the ?model accuracy has been greatly enhanced.
文摘The complexity of distribution network model mainly depends on the model scale of grid-connected distributed photovoltaic (PV) power generation. Therefore, the simulation performance of multi-scale PV model is the key factor of the simulation accuracy in the specific operating scenarios of distribution network. In this paper, a multi-scale model of grid connected PV distributed generation system is proposed based on the mathematical model of grid-connected distributed PV power generation. It is analyzed that differences of simulation performance, such as adaptability of simulation step size, accuracy of output and the effect on voltage profile of distribution network, between PV models with different scales in IEEE 33 node example. Simulation results indicate that the multi-scale model is effective in improving the accuracy and efficiency of simulation under different operating conditions of distribution network.
文摘Nowadays, renewable energy resources play an important role in replacing conventional energy resources such as fossil fuel by integrating solar, wind and geothermal energy. Photovoltaic energy is one?of?the very promising renewable energy resources which grew rapidly in the past few years, it can be used to produce electric energy through photovoltaic process. The primary objective of the research proposed in this paper is to facilitate the increasing penetration levels of PV systems in the electric distribution networks. In this work, the PV module electrical model is presented based on the mathematical equations and was implemented on MATLAB to simulate the non-linear characteristics I-V and P-V curves with variable input parameters which are irradiance and temperature based on Riyadh region. In addition, the reliability evaluation of distribution networks, including distributed generators of solar photovoltaic (PV) with varying output power capacity is presented also. The Monte Carlo simulation algorithm is applied to test the distribution network which is RBTS Bus 2 and the same has been conducted on the original case of distribution network substation 7029 which is located at KSA Riyadh. The two distribution networks have been modified to include the PV’s distributed generators. The distributed generators contribute to supply a part of the load during normal mode and supply the entire load during component failure or failure of grid operation supply. The PV stochastic models have been used to simulate the randomness of these resources. Moreover, the study shows that the implementation and integration of renewable resources as distributed generations have improved the reliability of the distribution networks.
文摘Integration of Solar Photovoltaic (PV) generation into an existing distribution system has many impacts on the system, with the power flow being one of the major issues. This impact is not generic for any network, but it may manifest itself either positively or negatively, depending on the grid configuration, interface control modes, operation mode, and load profile. Grid-connected PV systems have three control options of the local voltage controller of the interface DC-AC converter. These control modes are Power Factor control, voltage control, and Droop Voltage control. This paper aims at evaluating and comparing the impacts of those control modes on the grid power flow. A set of evaluation criteria and indices is defined and mathematically formulated. Based on the requirements of the used program (Power Factory Dig Silent V14.1.3), a computation plan (algorithm) has been proposed. The algorithm has been applied to a typical weak network and a wide range of simulations has been carried out. Simulation results have been thoroughly discussed and important findings have been concluded.
文摘The rapid spreading of the Photovoltaic (PV) Systems as Distributed Generation (DG) in medium and low voltage networks created many effects and changes on the existing power system networks. In this work, two methods have been used and applied to determine the optimal allocation and sizing of the PV to be installed as DGs (ranging from 250 kW up to 3 MW). The first one is to determine the location according to the maximal power losses reduction over the feeder. The second one is by using the Harmony Search Algorithm which is claimed to be a powerful technique for optimal allocation of PV systems. The results of the two techniques were compared and found to be nearly closed. Furthermore, investigation on the effects on the feeder in terms of voltage levels, power factor readings, and short circuit current levels has been done. All calculations and simulations are conducted by using the MATLAB Simulation Program. Some field calculations and observations have been expended in order to substantiate the research findings and validation.
文摘A massive plan has been drawn by the Karnataka state of India to initiate several solar power plants at different locations. In view of this, it is of great help to have reliable estimation on solar PV energy generation. Four solar PV power plants in Karnataka state are fully operational installed by Karnataka Power Corporation Limited (KPCL). They are located at Kolar, Belgaum and Raichur with 3 MW capacity each and at Mandya with 5 MW capacity. In the present study, using ground mounted weather station data solar power generation has been estimated and compared with actual generation for two consecutive years of 2012 and 2013 for one location initially, namely 3 MW Kolar Solar PV Plant. The procedure is repeated for rest of the plants. The simulated results have been corrected with ground mounted weather data. After such corrections, the simulated results have been compared with the actual energy generation of the four plants. Results showed a close match with a small deviation of about 5%. The model then applied throughout the state for every 0.25 degree station intervals in a grid manner. The annual energy generation obtained for the state varies from 1.53 to 1.73 MUs/MW. Central and south eastern part of the state are found to yield significantly higher solar power generation as compared to the northern part and south western part of Karnataka. Interestingly, north western part of Kodagu district has shown the least potential of 1.53 MUs/MW as compared to other parts. This can be attributed mainly due to low irradiation and high temperature condition at this location. The energy generated map from our study will be useful and helpful for both solar developers and decision makers of Karnataka state.
基金This project is supported by the National Natural Science Foundation of China(NSFC)(Nos.61806087,61902158).
文摘As wind and photovoltaic energy become more prevalent,the optimization of power systems is becoming increasingly crucial.The current state of research in renewable generation and power forecasting technology,such as wind and photovoltaic power(PV),is described in this paper,with a focus on the ensemble sequential LSTMs approach with optimized hidden-layers topology for short-term multivariable wind power forecasting.The methods for forecasting wind power and PV production.The physical model,statistical learningmethod,andmachine learning approaches based on historical data are all evaluated for the forecasting of wind power and PV production.Moreover,the experiments demonstrated that cloud map identification has a significant impact on PV generation.With a focus on the impact of photovoltaic and wind power generation systems on power grid operation and its causes,this paper summarizes the classification of wind power and PV generation systems,as well as the benefits and drawbacks of PV systems and wind power forecasting methods based on various typologies and analysis methods.
基金supported by National Science Foundation of China(61563032,61963025)Project supported by Gansu Basic Research Innovation Group(18JR3RA133)+1 种基金Industrial Support and Guidance Project for Higher Education Institutions of Gansu Province(2019C-05)Open Fund Project of Key Laboratory of Industrial Process Advanced Control of Gansu Province(2019KFJJ02).
文摘Because of system constraints caused by the external environment and grid faults,the conventional maximum power point tracking(MPPT)and inverter control methods of a PV power generation system cannot achieve optimal power output.They can also lead to misjudgments and poor dynamic performance.To address these issues,this paper proposes a new MPPT method of PV modules based on model predictive control(MPC)and a finite control set model predictive current control(FCS-MPCC)of an inverter.Using the identification model of PV arrays,the module-based MPC controller is designed,and maximum output power is achieved by coordinating the optimal combination of spectral wavelength and module temperature.An FCS-MPCC algorithm is then designed to predict the inverter current under different voltage vectors,the optimal voltage vector is selected according to the optimal value function,and the corresponding optimal switching state is applied to power semiconductor devices of the inverter.The MPPT performance of the MPC controller and the responses of the inverter under different constraints are verified,and the steady-state and dynamic control effects of the inverter using FCS-MPCC are compared with the traditional feedforward decoupling PI control in Matlab/Simulink.The results show that MPC has better tracking performance under constraints,and the system has faster and more accurate dynamic response and flexibility than conventional PI control.
文摘This document presents the evaluation and the monitoring of the performances of the first grid-connected photovoltaic system installed in the Center of Studies and Researches on the Renewable Energies (CERER) inaugurated on December 4th, 2012 by the governmental authorities of Senegal and Tenerife. This mini power plant of 3.15 kWc is a perfect example of the political will of the government which is to reduce the production cost of the electricity, with the diversification of the sources of production, and the greater use of the other sources such as the natural gas, the coal, the renewable energies. The evaluation of the performances of the installation is realized by using the indicators of efficiency and performance as the photovoltaic surface yield, the ratio of photovoltaic performance, the photovoltaic specific yield, and the losses of captures. The obtained results show that a big part of the energy shone during the period of observation was not able to be used further to circumstances such as the losses of conductivity, the heat losses or for example the defects on components. The analysis also shows that a large part of the produced energy is not injected because of the dilapidation of the network, the defects of landing but especially one disjunction sees frequently at the level of the point of injection.
文摘This paper primarily discusses the main circuit of single-phase inverter circuits.It begins by introducing the research context and the significance of the subject,then discusses the topology of grid-connected single-phase inverter circuits,continues by discussing the control strategy for grid-connected single-phase inverter circuits,realizes a sinusoidal pulse width modulation(SPWM)signal generation circuit and an inverse control algorithm program,and finally ensures good output waveform and fast dynamic response.In view of the hysteresis feature of the grid voltage’s synchronous signal sampling circuit,the acquisition function in digital signal processing(DSP)control chips is applied,and the reasons for the hysteresis phenomenon are thoroughly investigated.The reliability of the SPWM control algorithm is revealed through the results.
文摘Solar energy has been widely used in power generation.With the development of solar energy,the distributed photovoltaic power generation and the distributed grid-connected PV systems become the center of attention.This paper provided a brief introduction to distribution-level solar energy.Firstly,the development of solar energy was analyzed,and the distributed photovoltaic power generation was discussed.Secondly,the distributed grid-connected PV systems and basic theory of photovoltaic solar channel were analyzed.In order to ensure PV power is connected to grid stably and reliably,some related aspects such as the establishment of mathematical model for solar photovoltaic cell,the analysis of I-V characteristics of solar photovoltaic cell,and the tracking of its maximum power point(MPPT)to control the behaviour of the DC/DC converter were discussed.Finally,a simulation model was necessary to be established by using PSCAD/EMTDC function module to verify and simulate the mathematical model and control strategies,and some suggestions were put forward for the sustainable development of solar energy.
基金This work was supported by National High Technology Research and Development Program,“863 key technologies and development on large-scale grid-connected PV plants”(No.2011AA05A301).
文摘This paper describes the research on a largescale dispatchable grid-connected photovoltaic(PV)system for supplying power to the grid for dispatch instead of supplying the electricity to a local load.In order to maximise the value of the solar energy,a hybrid electricity storage consisting of batteries and supercapacitors is used with the PV system.This paper proposes a control strategy focusing on theDCpower at theDClink rather than at the grid-connected inverter.Two typical sets of real data,collected from existing sites,are used to demonstrate the practicality of the system.Finally,the simulation results are used to demonstrate the good performance and feasibility of the proposed system together with the proposed control strategy.
文摘Impedance analysis is an effective method to analyze the oscillation issue associated with grid-connected photovoltaic systems.However,the existing impedance modeling of a gridconnected photovoltaic inverter usually only considers the effect of a single perturbation frequency,ignoring the coupling frequency response between the internal control loops of a grid-connected inverter,which severely affects the accuracy of the stability analysis.Hence,a method of impedance modeling and stability analysis for grid-connected photovoltaic inverters considering cross-coupling frequency is proposed in this paper.First,the generation mechanism of frequency coupling in gridconnected photovoltaic inverters,and the relationship between the coupling frequency and perturbation frequency are analyzed.Secondly,a sequence impedance model of grid-connected photovoltaic systems considering the coupling frequency is established by using the harmonic linearization method.The impact of DC bus voltage control strategy on frequency coupling characteristics of a grid-connected photovoltaic system is evaluated,and the impact of a coupling frequency term on system stability is quantitatively analyzed.Finally,the advantages of the proposed method are verified by several simulations.The results show that the proposed impedance model can accurately predict the potential resonance points of the system,and the coupling frequency characteristics will become much stronger with smaller DC bus capacitance or larger bandwidth of the DC bus controller.
基金supported by Consejo Nacional de Ciencia y Tecnología (CONACyT) through a PhD studentship awarded to Manlio Salas Castillosupported by the Engineering and Physical Sciences Research Council, UK [grant number EP/S030786/1].
文摘Buildings are responsible for over 40% of total primary energy consumption in the US and EU and therefore improving building energy efficiency has significant potential for obtaining net-zero energy buildings reducing energy consumption. The concurrent demands of environmental comfort and the need to improve energy efficiency for both new and existing buildings have motivated research into finding solutions for the regulation of incoming solar radiation, as well as ensuring occupant thermal and visual comfort whilst generating energy onsite. Windows as building components offer the opportunity of addressing these issues in buildings. Building integration of photovoltaics permits building components such as semi-transparent façade, skylights and shading devices to be replaced with PV. Much progress has been made in photovoltaic material science, where smart window development has evolved in areas such as semi-transparent PV, electrochromic and thermochromic materials, luminescent solar concentrator and the integration of each of the latter technologies to buildings, specifically windows. This paper presents a review on intelligent window technologies that integrate renewable energy technologies with energy-saving strategies contributing potential solutions towards sustainable zero-energy buildings. This review is a comprehensive evaluation of intelligent windows focusing on state-of-the-art development in windows that can generate electricity and their electrical, thermal and optical characteristics. This review provides a summary of current work in intelligent window design for energy generation and gives recommendations for further research opportunities.
文摘Large-scale, grid-connected photovoltaic sys- tems have become an essential part of modem electric power distribution systems. In this paper, a novel approach based on the Markov method has been proposed to investigate the effects of large-scale, grid-connected photovoltaic systems on the reliability of bulk power systems. The proposed method serves as an applicable tool to estimate performance (e.g., energy yield and capacity) as well as reliability indices. The Markov method frame- work has been incorporated with the' multi-state models to develop energy states of the photovoltaic systems in order to quantify the effects of the photovoltaic systems on the power system adequacy. Such analysis assists planners to make adequate decisions based on the economical expectations as well as to ensure the recovery of the investment costs over time. The failure states of the components of photovoltaic systems have been considered to evaluate the sensitivity analysis and the adequacy indices including loss of load expectation, and expected energy not supplied. Moreover, the impacts of transitions between failures on the reliability calculations as well as on the long- term operation of the photovoltaic systems have been illustrated. Simulation results on the Roy Billinton test system has been shown to illustrate the procedure of the proposed frame work and evaluate the reliability benefits of using large-scale, grid-connected photovoltaic system on the bulk electric power systems. The proposed method can be easily extended to estimate the operating and maintenance costs for the financial planning of the photovoltaic system projects.