Heat Transfer Performance of a Novel Microchannel Embedded with Connected Grooves

To improve the heat transfer performance of microchannels,a novel microchannel embedded with connected grooves crossing two sidewalls and the bottom surface(type A)was designed.A comparative study of heat transfer was conducted regarding the performances of type A microchannels,microchannels embedded with grooves on their bottom(including types B and C),or on the sidewalls(type D)as well as smooth rectangular microchannels(type E)via a three-dimensional numerical simulation and experimental validation(at Reynolds numbers from 118 to 430).Numerical results suggested that the average Nusselt number of types A,B,C,and D microchannels were 106,73.4,50.1,and 12.6%higher than that of type E microchannel,respectively.The smallest synergy angle β and entropy generation number Ns,a were determined for type A microchannels based on field synergy and nondimensional entropy analysis,which indicated that type A exhibited the best heat transfer performance.Numerical flow analysis indicated that connected grooves induced fluid to flow along two different temperature gradients,which contributed to enhanced heat transfer performance.

Vacuum Infusion Molding Process (Part 2 VIMP Based on Grooves)

The optimal parameters for flow grooves and supply grooves were determined by a series of experiments,and the influences of various molding conditions on the mold filling process were analyzed.Furthermore,the whole VIMP procedure based on grooves was introduced in detail taking the manufacture of a sandwich panel as an example.

A Spectral Finite Difference Method for Analysis of a Fluid-Lubricated Herringbone Grooves Journal Bearing under a Special Case at Rectangle Groove

A spectral difference method is applied to get numerical solutions for a fluid-lubricated herringbone grooved journal bearing with trapezoidal grooves by previous work of the authors. However, an inexpedience in which Fourier series of the film profile does not converge at jump points of groove start or groove end in the case of rectangle groove was still remained. In the paper, an inexpedience of numerical analysis under a special case at rectangle groove is challenged to solve. As a result, for compensation of which Fourier series does not converge at jump points in a special case of rectangle groove, Fourier coefficient of fluid film thickness is proposed as taking the limit of which in a case trapezoidal groove at trapezoidal angle approaches 0.

Strength of Thin-Walled Lipped Channel Section Columns with Shell-Shaped Curved Grooves

Thin-walled member is structurally superior to a construction member. However, by reason of complexity in structure the stress and the deformation to yield the cross section are complicated. Specially, in case thin-walled members, such as thin-walled channel section columns, which are subjected to compressive force, these members produce the local buckling, distortional buckling and overall buckling. A number of experimental and theoretical investigations subjected to axial compressive force are generated for thin-walled channel section columns with triangle-shaped folded groove by Hancock [1] and with complex edge stiffeners and web stiffeners by Wang [2]. In case thin-walled channel section column with folded groove which is subjected to axial compressive force, it is cleared that the buckling mode shapes are ordinarily generated for local buckling mode shape of plate-panel composing cross section of member in short member aspect ratio and overall buckling mode shape as column and distortional buckling mode shape interacting between local buckling and overall buckling similarly normal thin-walled member. It is cleared analytically and experimentally that buckling strength and critical strength of thin-walled channel section column with folded groove can increase sharply in comparison with that of normal thin-walled member composing only plate-panel. In this paper a new cross section of shell-shaped curved groove [3] was proposed instead of the thin-walled lipped channel section column with triangle- and rectangle-shaped folded grooves used ordinarily, and therefore the comparison and the examination of buckling strength and buckling behavior were generated in the case of preparing triangle-shaped folded and shell-shaped curved grooves to web and flange of thin-walled channel section column. And then in order to investigate the buckling behavior on the thin-walled channel section column with folded and curved grooves, exact buckling strength and the buckling mode shapes are generated by using the transfer matrix method. The analytical local distortional and overall elastic buckling loads of thin-walled channel section column with folded and curved grooves can be obtained simultaneously by use of the transfer matrix method. Furthermore, a technique to estimate the buckling mode shapes of these members is also shown.

Internet-Based Optimization and Choice of Insert Grooves for Face-Milling

Manufacture is facing more furiously competition in the new century. It tends to be globalized. Rapid response and technology innovation have become the key factor to the success of manufacture enterprise. At present, internet-based manufacturing develops rapidly. With the development of engineering material and machining techniques, better cutting properties of metal cutting tools are required. The world is paying more attention to the study of indexable carbide inserts with three-dimensional complex grooves which can affect cutting properties directly and chip-controlling. So the variety and specification of indexable insert develop quickly and the application of insert with three-dimensional complex chip-former becomes wider and wider. Because milling is an interrupted cutting, the process of milling is complicated and the failure of the milling inserts is severe. It is important to choose suitable milling inserts groove for particular machining conditions before actual machining, it will extend tool life and raise productivity. Optimization and choice of inserts with complex groove via internet may serve for manufacture enterprises all over the world. The milling inserts with three-dimensional complex grooves are optimized and chosen via Internet in this paper. The face-milling process is studied, with the mathematics models of cutting force for different shape of cutting edges established, the cutting forces predicted and stress-fields of different insert grooves analyzed by FEM, according to the predictable results and the most suitable insert groove for particular machining conditions are optimized and chosen. The complex groove optimization and choice are based on a client/server model, with the client and server being on different machines across the internet. Communication between the client and server uses the TCP/IP. The result of optimization and choice will be sent to the users via Internet. Manufacturers all over the world can get the desired insert groove without paying for expensive experiments. Thus, the cost and lead time of products are reduced.

Numerical investigation of grooves effects on the thermal performance of helically grooved shell and coil tube heat exchanger

Heat exchangers are integral parts of important industrial units such as petrochemicals,medicine and power plants.Due to the importance of systems energy consumption,different modifications have been applied on heat exchangers in terms of size and structure.In this study,a novel heat exchanger with helically grooved annulus shell and helically coiled tube was investigated by numerical simulation.Helically grooves with the same pitch of the helical coil tube and different depth are created on the inner and outer wall of annulus shell to improve the thermal performance of heat exchanger.In the first section,thermal performance of the shell and coil heat exchanger with the helical grooves on its outer shell wall was compared with same but without helical grooves.At the second section,helically grooves created on both outer and inner wall of the annulus shell with different groove depths.The results showed that the heat exchanger with grooves on both inner and outer shell wall has better thermal performance up to 20%compared to the heat exchanger with grooves on only outer shell wall.The highest thermal performance achieves at lower flow rates and higher groove depths whereas the pressure drop did not increase significantly.

A New Method to Calculate Water Film Stiffness and Damping for Water Lubricated Bearing with Multiple Axial Grooves

Water lubricated guide bearings for hydro turbines and pumps are conventionally designed with multiple axial grooves to provide effectively cooling and flushing away abrasives.Due to the variety of groove configuration in terms of number and size,a predication of their performance is difficult.This paper deals with an analytical procedure to investigate groove effect on load capacity,stiffness and damping for this type of bearing where it is considered as an assembly of many inclined slide bearings.The result can be applied to bearings made of hard materials combined with low bearing pressure.

Analysis of roll-stamping process for rib grooves of ultra-high-strength beam parts

Roll-stamping technology,a new process with both roll-forming and stamping characteristics,is suitable for manufacturing ultra-high-strength beam parts,especially variable cross-section beam parts.The rib groove is a local shape often used in automotive parts for positioning,avoidance,and stiffness strengthening on longitudinal and stiffening beams.In this study,two typical rib grooves,the flat-and round-bottom rib grooves,were selected to investigate the characteristics of the roll-stamping process of rib grooves.Using the ABAQUS software platform,a simulation analysis model of rib-groove roll stamping was established and different size rib grooves produced by the roll-stamping process were compared and analyzed.The results show that when the fillet radius of the rib groove increases,the maximum Mises stress,the maximum strain,and the maximum thinning rate decrease.For roll stamping,the minimum safe fillet radii of the two types of rib grooves are 8 and 4 mm,respectively.

Finite Element Analysis for Groove Wander Prediction of Passenger Car Tires with the Longitudinal Tread Grooves

A finite element modeling technique is employed in this paper to predict the groove wander of longitudinal tread grooved tires. In generally, groove wander is the lateral force acting on a vehicle’s wheel resulting from the combination of rain grooves. If the lateral force of tire is generated by groove wander, unexpected lateral motion of vehicle will happen and it makes drivers uncomfortable. This paper describes the effect of groove wander according to the shape condition of tire tread groove and highway groove using the finite element analysis based on a static loading or a steady-state rolling assumption. The road groove can be located anywhere relative to the longitudinal tread groove. Therefore, the lateral force of the tire is changing depending on the location of the groove road. The numerical results for groove wander prediction of the longitudinal tread grooved tires are compared with the subjective evaluation. It is found that the waveform for the tire with varying grooved road position has a peak-to-peak lateral force in order to estimate the rating of groove wander. The effect of the road groove width and the pitch length on the peak-to-peak lateral force of tire is discussed. It is found that the prediction of FEA-based groove wander model using finite element analysis will be useful for the reliability design of the tire tread pattern design.

Tuning the Corrosion Resistance,Antibacterial Activity,and Cytocompatibility by Constructing Grooves on the Surface of Ti6Al4V3Cu Alloy

Ti6Al4V3Cu alloy is a promising biomaterial for combating implant-related infection.However,the antibacterial property of Ti6Al4V3Cu is expected to be enhanced due to the low content of Cu element in titanium.To address this issue,the antibacterial property of Ti6Al4V3Cu was tailored by the grooves with different groove widths(30μm,60μm,and 90μm)that were constructed on the surface of the Ti6Al4V3Cu by selective laser melting.The effect of grooves on corrosion resistance,antibacterial property,and cytocompatibility was investigated.The electrochemical tests showed that the corrosion resistance decreased with increasing groove width.The antibacterial tests indicated that the groove with a width of 30μm and 90μm groups showed better antibacterial activity against S.aureus(>90%)compared with the groove with a width of 60μm.The in vitro study suggested that all samples with different grooves were found to exhibit good cytocompatibility with osteoblast cells.It is considered that creating grooves on Ti6Al4V3Cu by selective laser melting is a promising strategy to enhance the antibacterial activity without sacrificing cytocompatibility.

Simulated Research of Enhanced Heat Transfer Characteristics of LNG in Rectangular Small Channels with Circumference Micro-Grooves

In view of the technical development bottleneck of 3D printing manufacturing compact heat exchanger for supercritical LNG,a new passive enhanced heat transfer technology is proposed by developing circumferential micro-grooves on the top and bottom walls of rectangular small channels.Numerical simulation of heat transfer enhancement and flow resistance characteristics of LNG in the enhanced channels with micro-grooves is performed.The geometrical dimensions such as the groove depth,the groove width and the center distance between two adjacent micro-grooves were optimized,and then the heat transfer enhancement and flow of LNG within the range of 120 K-250 K which across the critical temperature after the use of the strengthening technology were discussed.Then,further effects of working fluid temperature,mass flow(Reynolds number),and inlet pressure on heat transfer coefficient(Nusselt number),friction factor,and comprehensive coefficient were investigated.In addition,by the analysis of local flow characteristics near the micro-grooves,the heat transfer mechanism is discussed.

A modal theory and recursion RTCM algorithm for gratings of deep grooves and arbitrary profile

A modal theory for gratings of deep grooves and arbitrary shape is developed. The theory is implemented with an algorithm of recursion reflection-transmission coefficient matrix (RTCM). Several cases of plane wave with arbitrary polarization and arbitrary angle of incidence diffracted from gratings of deep grooves and arbitrary profile are calculated. It is found that this method is more accurate, more stable and faster than others.

An analysis of the Circumferential Grooves Casing Treatment for transonic compressor flow

The stall mechanism of the NASA Rotor 37 is investigated through the analysis of the critical flow structures near the stall under the transonic condition. The performance of the rotor with Circumferential Grooves Casing Treatment (CGCT) is also studied based on the Reynolds-Averaging Navier-Stokes approach. The study finds that stall margin improvement can be achieved without significant penalty on the efficiency for the two CGCT configurations applied. The effects of circumferential grooves on the critical flow structures are studied through the analysis of the tip leakage mass and momentum transport that further re-veal the CGCT mechanism.

Liver surface depressions in the presence of diaphragmatic muscular bands on trans-illumination

Traditional descriptions of liver anatomy refer to a smooth,convex surface contacting the diaphragm.Surface depressions are recognized anatomic variants.There are many theories to explain the cause of the depressions.We discuss the theory that these are caused by hypertrophic muscular bands in the diaphragm.

Optimization design of main parameters for double spiral grooves face seal

The optimization design of the parameters, such as the groove depth, groove number, ratio of the groove width to the land width, and spiral angle of a new kind of double spiral grooves face seal, which works under the condition of high velocity, high sealing pressure and ultra-low temperature, is presented under the assump-tion of fixed closure force by finite element analysis method. The results show that the stiffness of the maximum film can be obtained when the ratio of the groove width to the land width is 0.5 and the spiral angle is about 75 degrees, when the influence of the groove number on the sealing performance is not obvious.

RANS simulations of the U and V grooves effect in the subcritical flow over four rotated circular cylinders

This paper presents a CFD study about the effect of the V and U grooves in the flow over four cylinders in diamond shape configuration at subcritical flow conditions（Re= 41 000）. The k- ε Realizable turbulence model was implemented to fully structured hexahedral grids with near-wall refinements. Results showed that the numerical model was able to reproduce the impinging flow pattern and the repulsive forces present in the lateral cylinders of the smooth cylinder array. As a consequence of the flow alignment induced by the grooves, a jet-flow is formed between the lateral cylinders, which could cause an important vortex induced vibration effect especially in the rear cylinder. The magnitudes of the shear stresses at the valleys and peaks for the V grooved cylinders were lower than those of the U grooved cylinders, but the separation points were delayed due the U grooves presence. It is discussed the presence of a blowing effect caused by counter-rotating eddies located near the grooves peaks that cause a decrease of the shear stresses in the valleys, and promote them at the peaks.

Key machining characteristics in ultrasonic vibration cutting of single crystal silicon for micro grooves

Structured complex silicon components have been widely used in solar cells,biomedical engineering and other industrial applications.As silicon is a typical brittle material,ultrasonic vibration cutting(UVC)is a promising method to achieve better cutting performance than conventional techniques.High-frequency ID UVC possesses higher nominal cutting speed and material removal rate than many 2D/3D UVC systems,and thus,it has great development potential in industrial applications of structured silicon components.However,few researchers have applied ID UVC to the cutting of structured silicon surfaces,since its main drawback is tool marks imprinted by the vibration on machined surface.In this study,to uncover the key machining characteristics under the condition of ID UVC,a series of tests involving diamond cutting grooves were first performed on the silicon surface.The machined surface and chips were subsequently measured and analyzed to evaluate the critical undeformed chip thickness,surface characteristics,and chip formation.Regarding the main drawback of ID UVC,a novel theoretical model was developed for predicting the length of tool marks and evaluating the impact of tool marks on the surface finish.The results demonstrated that the critical undeformed chip thickness of silicon reached 1030 nm under a certain vibration amplitude and that an array of micro grooves was generated at the plastic region with a surface roughness(7?a)as low as 1.11 nm.Moreover,the micro topography of the continuous chips exhibited discontinuous clusters of lines with diameters of dozens of nanometers,only composed of polysilicon.The novel theoretical model was able to predict the length of tool marks with low error.Thus,the impact of tool marks on the surface finish can be reduced and even eliminated with help of the model.

Duodenojejunostomy treatment of groove pancreatitis-induced stenosis and obstruction of the horizontal duodenum:A case report

BACKGROUND Groove pancreatitis(GP)is a rare condition affecting the pancreatic groove region within the dorsal-cranial part of the pancreatic head,duodenum,and common bile duct.As a rare form of chronic pancreatitis,GP poses a diagnostic and therapeutic challenge for clinicians.GP is frequently misdiagnosed or not considered;thus,the diagnosis is often delayed by weeks or months.The treatment of GP is complicated and often requires surgical intervention,especially pancreatoduodenectomy.CASE SUMMARY A 66-year-old man with a history of long-term drinking was admitted to the gastroenterology department of our hospital,complaining of vomiting and acid reflux.Upper gastrointestinal endoscopy showed luminal stenosis in the descending part of the duodenum.Abdominal computed tomography showed slight exudation in the descending and horizontal parts of the duodenum with broadening of the groove region,indicating local pancreatitis.The symptoms of intestinal obstruction were not relieved with conservative therapy,and insertion of an enteral feeding tube was not successful.Exploratory laparoscopy was performed and revealed a hard mass with scarring in the horizontal part of the duodenum and stenosis.Intraoperative frozen section analysis showed no evidence of malignancy,and side-to-side duodenojejunostomy was performed.Routine pathologic examination showed massive proliferation of fibrous tissue,hyaline change,and the proliferation of spindle cells.Based on the radiologic and pathologic characteristics,a diagnosis of GP was made.The patient presented with anastomotic obstruction postoperatively and took a long time to recover,requiring supportive therapy.CONCLUSION GP often involves the descending and horizontal parts of the duodenum and causes duodenal stenosis,impaired duodenal motility,and gastric emptying due to fibrosis.

TaqMan MGB探针实时荧光定量PCR快速检测布鲁氏菌

目的利用新一代TaqMan MGB探针技术,建立特异敏感的实时荧光定量PCR方法,用于布鲁氏菌的快速检测。方法针对布鲁氏菌基因组中16SrRNA序列设计特异性引物和探针,建立一套基于TaqMan MGB探针技术的实时荧光定量PCR方法,验证方法的特异性、敏感性和稳定性,对2008-2010年期间采集的773份动物样本中的布鲁氏菌进行检测,并与普通PCR方法进行比较分析。结果建立的TaqMan MGB探针实时荧光定量PCR方法对布鲁氏菌的检测具有高度的特异性,对小肠结肠耶尔森菌、假结核耶尔森菌、肠炎沙门氏菌、大肠埃希菌、铜绿假单胞菌、空肠弯曲菌、泰泽氏菌均无交叉反应。生成的标准曲线的相关系数为0.999,斜率为-3.301,TaqMan MGB探针实时荧光定量PCR效率为100.872%。TaqMan MGB探针实时荧光定量PCR能够准确地从布鲁氏菌阳性样本中检测到布鲁氏菌DNA,最低能够检测到的布鲁氏菌数量为9.3拷贝,比常规PCR方法的灵敏度高100倍。对773份动物样本进行检测,结果TaqMan MGB探针实时荧光定量PCR能检出53份布鲁氏菌阳性样本,而常规PCR只检出37份阳性。结果显示,TaqMan MGB探针实时荧光定量PCR方法比常规PCR方法更敏感,能够直接从动物样本中检出布鲁氏菌DNA,检测时间仅为2h。结论本研究首次建立了直接用于检测动物样本中布鲁氏菌的TaqMan MGB探针实时荧光定量PCR方法,该技术适用于传染性病原体的快速检测与鉴定。

Microstructure and Mechanical Strength Predictive Modeling in Al 5052-Trapezoidal Grooved SS 304 Explosive Cladding

Aluminum alloy plates were explosively cladded to stainless steel plates with trapezoidal grooves on the mating surface.The process parameters viz,loading ratio,standoff distance and flyer plate thickness were varied based on the Taguchi analogy.The variation in the process parameters alters the kinetic energy dissipation and the deformation work performed at the interface,and dictates the interfacial wave amplitude and the mechanical strength of the dissimilar explosive clad.The optimum level of process parameters for attaining higher tensile and shear strength is computed by signal-to-noise ratio.Further,a mathematical model is developed for calculating tensile and shear strength of the clad,based on the regression analysis using statistical software Minitab-16,and the level of fit is determined by analysis of variance.