Improving Satellite-Retrieved Cloud Base Height with Ground-Based Cloud Radar Measurements

Cloud base height(CBH) is a crucial parameter for cloud radiative effect estimates, climate change simulations, and aviation guidance. However, due to the limited information on cloud vertical structures included in passive satellite radiometer observations, few operational satellite CBH products are currently available. This study presents a new method for retrieving CBH from satellite radiometers. The method first uses the combined measurements of satellite radiometers and ground-based cloud radars to develop a lookup table(LUT) of effective cloud water content(ECWC), representing the vertically varying cloud water content. This LUT allows for the conversion of cloud water path to cloud geometric thickness(CGT), enabling the estimation of CBH as the difference between cloud top height and CGT. Detailed comparative analysis of CBH estimates from the state-of-the-art ECWC LUT are conducted against four ground-based millimeter-wave cloud radar(MMCR) measurements, and results show that the mean bias(correlation coefficient) is0.18±1.79 km(0.73), which is lower(higher) than 0.23±2.11 km(0.67) as derived from the combined measurements of satellite radiometers and satellite radar-lidar(i.e., Cloud Sat and CALIPSO). Furthermore, the percentages of the CBH biases within 250 m increase by 5% to 10%, which varies by location. This indicates that the CBH estimates from our algorithm are more consistent with ground-based MMCR measurements. Therefore, this algorithm shows great potential for further improvement of the CBH retrievals as ground-based MMCR are being increasingly included in global surface meteorological observing networks, and the improved CBH retrievals will contribute to better cloud radiative effect estimates.

Ground-Based Cloud Using Exponential Entropy/Exponential Gray Entropy and UPSO

Objective and accurate classification model or method of cloud image is a prerequisite for accurate weather monitoring and forecast.Thus safety of aircraft taking off and landing and air flight can be guaranteed.Thresholding is a kind of simple and effective method of cloud classification.It can realize automated ground-based cloud detection and cloudage observation.The existing segmentation methods based on fixed threshold and single threshold cannot achieve good segmentation effect.Thus it is difficult to obtain the accurate result of cloud detection and cloudage observation.In view of the above-mentioned problems,multi-thresholding methods of ground-based cloud based on exponential entropy/exponential gray entropy and uniform searching particle swarm optimization(UPSO)are proposed.Exponential entropy and exponential gray entropy make up for the defects of undefined value and zero value in Shannon entropy.In addition,exponential gray entropy reflects the relative uniformity of gray levels within the cloud cluster and background cluster.Cloud regions and background regions of different gray level ranges can be distinguished more precisely using the multi-thresholding strategy.In order to reduce computational complexity of original exhaustive algorithm for multi-threshold selection,the UPSO algorithm is adopted.It can find the optimal thresholds quickly and accurately.As a result,the real-time processing of segmentation of groundbased cloud image can be realized.The experimental results show that,in comparison with the existing groundbased cloud image segmentation methods and multi-thresholding method based on maximum Shannon entropy,the proposed methods can extract the boundary shape,textures and details feature of cloud more clearly.Therefore,the accuracies of cloudage detection and morphology classification for ground-based cloud are both improved.

Examination of the Quality of GOSAT/CAI Cloud Flag Data over Beijing Using Ground-based Cloud Data

It has been several years since the Greenhouse Gases Observing Satellite （GOSAT） began to observe the distribution of CO2 and CH4 over the globe from space. Results from Thermal and Near-infrared Sensor for Carbon Observation-Cloud and Aerosol Imager （TANSO-CAI） cloud screening are necessary for the retrieval of CO2 and CH4 gas concentrations for GOSAT TANSO-Fourier Transform Spectrometer （FTS） observations. In this study, TANSO-CAI cloud flag data were compared with ground-based cloud data collected by an all-sky imager （ASI） over Beijing from June 2009 to May 2012 to examine the data quality. The results showed that the CAI has an obvious cloudy tendency bias over Beijing, especially in winter. The main reason might be that heavy aerosols in the sky are incorrectly determined as cloudy pixels by the CAI algorithm. Results also showed that the CAI algorithm sometimes neglects some high thin cirrus cloud over this area.

Contribution of Ground-Based Cloud Observation to Satellite-Based Cloud Discrimination

One of the biggest factors to deteriorate the satellite product quality is cloud coverage. Therefore, cloud masking process is important to improve the quality of various satellite products. However, satellite-based cloud discrimination algorithm has been developing and efficient ground-based cloud observations are necessary to validate satellite-based cloud discrimination. The purpose of this study is to develop the efficient ground-based cloud observation methodology using whole sky camera. This paper deals with methods how to discriminate cloud portions on whole sky image, how to apply the ground-based cloud observation to the validations for satellite products. For the cloud discrimination on whole sky image, we propose SI （sky index） and BI （brightness index） calculated from RGB （red, green and blue） channels. SI shows the extent of the blueness and gray scale and BI indicates the extent of the brightness. Sun, cloud and blue sky portions are divided by SI and BI threshold. As an application of ground-based cloud observation for the validation of satellite products, clouds portions discriminated from whole sky image are projected onto ground surface with map coordinate. We also examine to compare with cloud portions on whole sky images and MODIS （MODerate resolution Imaging Spectroradiometer） image as one of experiments. The proposed ground-based cloud observation method and its extension to satellite-based cloud discrimination should be connected to improve the quality of satellite products.

Salient Local Binary Pattern for Ground-Based Cloud Classification

Ground-based cloud classification is challenging due to extreme variations in the appearance of clouds under different atmospheric conditions. Texture classification techniques have recently been introduced to deal with this issue. A novel texture descriptor, the salient local binary pattern （SLBP）, is proposed for ground-based cloud classification. The SLBP takes advantage of the most frequently occurring patterns （the salient patterns） to capture descriptive information. This feature makes the SLBP robust to noise. Experimental results using ground-based cloud images demonstrate that the proposed method can achieve better results than current state-of-the-art methods.

Ground-based and additional science support for SMILE

The joint European Space Agency and Chinese Academy of Sciences Solar wind Magnetosphere Ionosphere Link Explorer(SMILE)mission will explore global dynamics of the magnetosphere under varying solar wind and interplanetary magnetic field conditions,and simultaneously monitor the auroral response of the Northern Hemisphere ionosphere.Combining these large-scale responses with medium and fine-scale measurements at a variety of cadences by additional ground-based and space-based instruments will enable a much greater scientific impact beyond the original goals of the SMILE mission.Here,we describe current community efforts to prepare for SMILE,and the benefits and context various experiments that have explicitly expressed support for SMILE can offer.A dedicated group of international scientists representing many different experiment types and geographical locations,the Ground-based and Additional Science Working Group,is facilitating these efforts.Preparations include constructing an online SMILE Data Fusion Facility,the discussion of particular or special modes for experiments such as coherent and incoherent scatter radar,and the consideration of particular observing strategies and spacecraft conjunctions.We anticipate growing interest and community engagement with the SMILE mission,and we welcome novel ideas and insights from the solar-terrestrial community.

Comparison of Precipitation Observations from a Prototype Space-based Cloud Radar and Ground-based Radars

A prototype space-based cloud radar has been a precipitation system over Tianjin, China in July developed and was installed on an airplane to observe 2010. Ground-based S-band and Ka-band radars were used to examine the observational capability of the prototype. A cross-comparison algorithm between different wavelengths, spatial resolutions and platform radars is presented. The reflectivity biases, correlation coefficients and standard deviations between the radars are analyzed. The equivalent reflectivity bias between the S- and Ka-band radars were simulated with a given raindrop size distribution. The results indicated that reflectivity bias between the S- and Ka-band radars due to scattering properties was less than 5 dB, and for weak precipitation the bias was negligible. The prototype space-based cloud radar was able to measure a reasonable vertical profile of reflectivity, but the reflectivity below an altitude of 1.5 km above ground level was obscured by ground clutter. The measured refiectivity by the prototype space-based cloud radar was approximately 10.9 dB stronger than that by the S-band Doppler radar （SA radar）, and 13.7 dB stronger than that by the ground-based cloud radar. The reflectivity measured by the SA radar was 0.4 dB stronger than that by the ground-based cloud radar. This study could provide a method for the quantitative examination of the observation ability for space-based radars.

Airborne Measurements of the Impact of Ground-based Glaciogenic Cloud Seeding on Orographic Precipitation

Data from in situ probes and a vertically-pointing ram-wave Doppler radar aboard a research aircraft are used to study the cloud microphysical effect of glaciogenic seeding of cold-season orographic clouds. A previous study （Geerts et al., 2010） has shown that radar reflectivity tends to be higher during seeding periods in a shallow layer above the ground downwind of ground-based silver iodide （AgI） nuclei generators. This finding is based on seven flights, conducted over a mountain in Wyoming （the Unites States）, each with a no-seeding period followed by a seeding period. In order to assess this impact, geographically fixed flight tracks were flown over a target mountain, both upwind and downwind of the AgI generators. This paper examines data from the same flights for further evidence of the cloud seeding impact. Com- posite radar data show that the low-level reflectivity increase is best defined upwind of the mountain crest and downwind of the point where the cloud base intersects the terrain. The main argument that this increase can be attributed to AgI seeding is that it is confined to a shallow layer near the ground where the flow is turbulent. Yet during two flights when clouds were cumuliform and coherent updrafts to flight level were recorded by the radar, the seeding impact was evident in the flight-level updrafts （about 610 m above the mountain peak） as a significant increase in the ice crystal appears short-lived as it is not apparent just downwind of concentration in all size bins. The seeding effect the crest.

Assessment of FY-4A and Himawari-8 Cloud Top Height Retrieval through Comparison with Ground-Based Millimeter Radar at Sites in Tibet and Beijing

The accuracy of passive satellite cloud top height (CTH) retrieval shows regional dependence. This paper assesses the CTH derived from the FY-4A and Himawari-8 satellites through comparison with those from the ground-based millimeter radar at two sites: Yangbajing, Tibet, China (YBJ), and the Institute of Atmospheric Physics (IAP), Beijing, China. The comparison shows that Himawari-8 missed more CTHs at night than FY-4A, especially at YBJ. It is found that the CTH difference (CTHD;radar CTH minus satellite CTH) for FY-4A and Himawari-8 is 0.06 ± 1.90 km and −0.02 ± 2.40 km at YBJ respectively, and that is 0.93 ± 2.24 km and 0.99 ± 2.37 km at IAP respectively. The discrepancy between the satellites and radar at IAP is larger than that at YBJ. Both satellites show better performance for mid-level and low-level clouds than for high-level clouds at the two sites. The retrievals from FY-4A agree well with those from Himawari-8, with a mean difference of 0.08 km at YBJ and 0.06 km at IAP. It is found that the CTHD decreases as the cloud depth increases at both sites. However, the CTHD has no obvious dependence on cloud layers and fractions. Investigations show that aerosol concentration has little impact on the CTHD. For high and thin clouds, the CTHD increases gradually with the increase of the surface temperature, which might be a key factor causing the regional discrepancy between IAP and YBJ.

Preliminary Results of the Ground-Based Orographic Snow Enhancement Experiment for the Easterly Cold Fog (Cloud) at Daegwallyeong during the 2006 Winter

The snow enhancement experiments, carried out by injecting AgI and water vapor into orographically enhanced clouds （fog）, have been conducted to confirm Li and Pitter＇s forced condensation process in a natural situation. Nine ground-based experiments have been conducted at Daegwallyeong in the Taebaek Mountains for the easterly foggy days from January-February 2006. We then obtained the optimized conditions for the Daegwallyeong region as follows： the small seeding rate （1.04 g min-1） of AgI for the easterly cold fog with the high humidity of Gangneung. Additional experiments are needed to statistically estimate the snowfall increment caused by the small AgI seeding into the orographical fog （cloud） over the Taeback Mountains.

An Evidence of Aerosol Indirect Effect on Stratus Clouds from the Integrated Ground-Based Measurements at the ARM Shouxian Site

The aerosol effect on clouds was explored using remote sensing of aerosol and cloud data at Shouxian, China. Non-precipitation, ice-free, and overcast clouds were firstly chosen by a combination of sky im- ages from the Total Sky Imager （TSI）, cloud base heights from the Ceilometer, and vertical temperature profiles from the Balloon-Borne Sounding System （BBSS）. Six cases were chosen in summer, and seven in autumn. The averaged cloud effective radii （re）, cloud optical depth （COD）, aerosol total light scattering coefficient （a）, and liquid water path （LWP） are, respectivey, 6.47 μm, 35.4, 595.9 mm-1, 0.19 mm in summer, and 6.07 μm, 96.0, 471.7 mm-1, 0.37 mm in autumn. The correlation coefficient between re and tc was found to change from negative to positive value as LWP increases.

Cloud Base Height and Effective Cloud Emissivity Retrieval with Ground-Based Infrared Interferometer

Based on ground-based Atmospheric Emitted Radiance Interferometer (AERI) observations in Shouxian, Anhui province, China, the authors retrieve the cloud base height (CBH) and effective cloud emissivity by using the minimum root-mean-square difference method. This method was originally developed for satellite remote sensing. The high-temporal-resolution retrieval results can depict the trivial variations of the zenith clouds continu-ously. The retrieval results are evaluated by comparing them with observations by the cloud radar. The comparison shows that the retrieval bias is smaller for the middle and low cloud, especially for the opaque cloud. When two layers of clouds exist, the retrieval results reflect the weighting radiative contribution of the multi-layer cloud. The retrieval accuracy is affected by uncertainties of the AERI radiances and sounding profiles, in which the role of uncertainty in the temperature profile is dominant.

Influence of assimilating ground-based microwave radiometer data into the WRF model on precipitation

Ground-based microwave radiometers profilers(MWRPs)have been used in numerical weather prediction(NWP)systems and show different impacts on forecasts.Currently,there are around hundreds of ground-based MWPRs used in weather stations over China;however,the application of MWPRs in NWP systems is rather limited.In this work,two MWRP retrieved profiles were assimilated into the Weather Research and Forecasting(WRF)model for a rainstorm event that occurred in Beijing,China.The quality of temperature and humidity profiles retrieved from the MWRP was evaluated against radiosonde observations and showed the reliability of the two MWRP products.Then,comparisons between the measurements of ground-based rain gauges and the corresponding forecasted precipitation in different periods of the rainstorm were investigated.The results showed that assimilating the two MWRPs affected the distribution and intensity of rainfall,especially in the early stage of the rainstorm.With the development of the rainstorm,adding MWRP data showed only a slight influence on the precipitation during the stable and mature period of the rainstorm,since the two MWRP observations were too limited to affect the large area of heavy rainfall.

Long-term gravity changes in Chinese mainland from GRACE and ground-based gravity measurements

A long-term （9 years） gravity change in Chinese mainland is obtained on the basis of observation of the ground-based national gravity network. The result shows several features that may be related to sore, large-scale groundwater pumping in North China, glacier-water flow and storage in Tianshan region, and pre seismic gravity changes of the 2008 MsS. 0 Wenchuan earthquake, which are spatially similar to co-seismi, changes but reversed in sign. These features are also shown in the result of the satellite-based GRACE obser vation, after a height effect is corrected with GPS data.

An approach to wide-field imaging of linear rail ground-based SAR in high squint multi-angle mode

Ground-based synthetic aperture radar(GB-SAR) has been successfully applied to the ground deformation monitoring.However, due to the short length of the GB-SAR platform, the scope of observation is largely limited. The practical applications drive us to make improvements on the conventional linear rail GB-SAR system in order to achieve larger field imaging. First, a turntable is utilized to support the rotational movement of the radar.Next, a series of high-squint scanning is performed with multiple squint angles. Further, the high squint modulation phase of the echo data is eliminated. Then, a new multi-angle imaging method is performed in the wave number domain to expand the field of view. Simulation and real experiments verify the effectiveness of this method.

0-10 KM TEMPERATURE AND HUMIDITY PROFILES RETRIEVAL FROM GROUND-BASED MICROWAVE RADIOMETER

Deviation exists between measured and simulated microwave radiometer sounding data. The bias results in low-accuracy atmospheric temperature and humidity profiles simulated by Back Propagation artificial neural network models. This paper evaluated a retrieving atmospheric temperature and humidity profiles method by adopting an input data adjustment-based Back Propagation artificial neural networks model. First, the sounding data acquired at a Nanjing meteorological site in June 2014 were inputted into the Mono RTM Radiative transfer model to simulate atmospheric downwelling radiance at the 22 spectral channels from 22.234 GHz to 58.8 GHz, and we performed a comparison and analysis of the real observed data; an adjustment model for the measured microwave radiometer sounding data was built. Second, we simulated the sounding data of the 22 channels using the sounding data acquired at the site from 2011 to 2013. Based on the simulated rightness temperature data and the sounding data, BP neural network-based models were trained for the retrieval of atmospheric temperature, water vapor density and relative humidity profiles. Finally, we applied the adjustment model to the microwave radiometer sounding data collected in July 2014, generating the corrected data. After that, we inputted the corrected data into the BP neural network regression model to predict the atmospheric temperature, vapor density and relative humidity profile at 58 high levels from 0 to 10 km. We evaluated our model's effect by comparing its output with the real measured data and the microwave radiometer's own second-level product. The experiments showed that the inversion model improves atmospheric temperature and humidity profile retrieval accuracy; the atmospheric temperature RMS error is between 1 K and 2.0 K; the water vapor density's RMS error is between 0.2 g/m^3 and 1.93 g/m3; and the relative humidity's RMS error is between 2.5% and 18.6%.

Ground-Based Atmospheric CO_(2),CH_(4),and CO Column Measurements at Golmud in the Qinghai-Tibetan Plateau and Comparisons with TROPOMI/S5P Satellite Observations

Measurements of carbon dioxide(CO_(2)),methane(CH_(4)),and carbon monoxide(CO)are of great importance in the Qinghai-Tibetan region,as it is the highest and largest plateau in the world affecting global weather and climate systems.In this study,for the first time,we present CO_(2),CH_(4),and CO column measurements carried out by a Bruker EM27/SUN Fourier-transform infrared spectrometer(FTIR)at Golmud(36.42°E,94.91°N,2808 m)in August 2021.The mean and standard deviation of the column-average dry-air mixing ratio of CO_(2),CH_(4),and CO(XCO_(2),XCH_(4),and XCO)are 409.3±0.4 ppm,1905.5±19.4 ppb,and 103.1±7.7 ppb,respectively.The differences between the FTIR co-located TROPOMI/S5P satellite measurements at Golmud are 0.68±0.64%(13.1±12.2 ppb)for XCH_(4) and 9.81±3.48%(–10.7±3.8 ppb)for XCO,which are within their retrieval uncertainties.High correlations for both XCH_(4) and XCO are observed between the FTIR and S5P satellite measurements.Using the FLEXPART model and satellite measurements,we find that enhanced CH_(4) and CO columns in Golmud are affected by anthropogenic emissions transported from North India.This study provides an insight into the variations of the CO_(2),CH_(4),and CO columns in the Qinghai-Tibetan Plateau.

Seismic Noise Suppression for Ground-Based Investigation of an Inertial Sensor by Suspending the Electrode Cage

Performance test of a high precise accelerometer or an inertial sensor on the ground is inevitably limited by the seismic noise. A torsion pendulum has been used to investigate the performances of an electrostatic accelerometer, where the test mass is suspended by a fiber to compensate for its weight, and this scheme demonstrates an advantage, compared with the high-voltage levitation scheme, in which the effect of the seismic noise can be suppressed for a few orders of magnitude in low frequencies. In this work, the capacitive electrode cage is proposed to be suspended by another pendulum, and theoretical analysis shows that the effects of the seismic noise can be further suppressed for more than one order by suspending the electrode cage.

Ground-based/UAV-LiDAR data fusion for quantitative structure modeling and tree parameter retrieval in subtropical planted forest

Light detection and ranging(LiDAR)has contributed immensely to forest mapping and 3D tree modelling.From the perspective of data acquisition,the integration of LiDAR data from different platforms would enrich forest information at the tree and plot levels.This research develops a general framework to integrate ground-based and UAV-LiDAR(ULS)data to better estimate tree parameters based on quantitative structure modelling(QSM).This is accomplished in three sequential steps.First,the ground-based/ULS LiDAR data were co-registered based on the local density peaks of the clustered canopy.Next,redundancy and noise were removed for the ground-based/ULS LiDAR data fusion.Finally,tree modeling and biophysical parameter retrieval were based on QSM.Experiments were performed for Backpack/Handheld/UAV-based multi-platform mobile LiDAR data of a subtropical forest,including poplar and dawn redwood species.Generally,ground-based/ULS LiDAR data fusion outperforms ground-based LiDAR with respect to tree parameter estimation compared to field data.The fusion-derived tree height,tree volume,and crown volume significantly improved by up to 9.01%,5.28%,and 18.61%,respectively,in terms of rRMSE.By contrast,the diameter at breast height(DBH)is the parameter that has the least benefits from fusion,and rRMSE remains approximately the same,because stems are already well sampled from ground data.Additionally,particularly for dense forests,the fusion-derived tree parameters were improved compared to those derived from ground-based LiDAR.Ground-based LiDAR can potentially be used to estimate tree parameters in low-stand-density forests,whereby the improvement owing to fusion is not significant.

基于Spring Cloud的分布式医疗数据平台建设

为解决互联网时代医疗大数据的可靠存储问题,探索异构数据的有效处理方案,加强医疗数据检索能力。提出一种基于Spring Cloud的分布式医疗数据平台建设方案,该方案通过Spring Cloud技术构建分布式架构,选取MongoDB非关系型数据库作为分布式存储,同时对数据进行标准化、分词等操作,从而实现一个异构数据可存储、系统高可用、规模易扩展、检索高效率的医疗数据平台。