By applying experimental method, the bolt stress and supporting mechanism is studied during the deformation process of a rock mass containing a weak interlayer. The force measuring bolt is installed manually and instr...By applying experimental method, the bolt stress and supporting mechanism is studied during the deformation process of a rock mass containing a weak interlayer. The force measuring bolt is installed manually and instrumented five pairs of symmetrical strain gauges. The experimental results show that the fully grouted bolt suffers tensile, compressive, bending and shear stress at the same time. The bolt stress evolution is closely related to the deformation stages of the rock mass which are very gradually varying stage, gradually varying stage at the pre-peak and suddenly varying stage at the post peak stage.The axial compressive stress in the bolt is mainly induced by the moment. Thus, in most cases the axial compressive stress is distributed on one side of the bolt. For axial stresses, induced by the axial force and the bending moment at the post-peak stage, three types of changing are observed, viz. increasingincreasing type, decreasing-increasing type and increasing-decreasing type. The stress characteristics of the bolt section in the weak interlayer are significantly different from those in the hard rock. The failure models of the anchored bolt are tensile failure and shear failure, respectively. The bolt not only provides constraints on the free surface of the rock mass, but also resists the axial and lateral loading by the bending moment. This study provides valuable guidelines for bolting support design and its safety assessment.展开更多
Fully grouted bolts are a key component of the support system for underground openings.Although considerable effort has been made in the simulation of the reinforcement effect of the fully grouted bolts on the rock ma...Fully grouted bolts are a key component of the support system for underground openings.Although considerable effort has been made in the simulation of the reinforcement effect of the fully grouted bolts on the rock masses surrounding underground openings,most of the work has limited significance since the structural element approach is used.This study proposes a local homogenization approach(L-H approach)that integrates elastoplastic mechanics,composite mechanics,and analytical approaches with numerical simulation to effectively simulate the reinforcement effect of the fully grouted bolt on deep surrounding rock masses.In the L-H approach,the representative volume of bolted rock mass(RVBRM)with a fully grouted bolt is established based on the original mesh model utilized in the rockbolt element approach.The RVBRM is a regular quadrangular prism with a cross-sectional size equal to the bolt spacing and a length equal to the bolt length.The RVBRM is homogenized by the L-H approach from a unidirectional bolt-reinforced composite into a homogeneous transversely isotropic medium whose mechanical properties are described by a new transversely isotropic elastoplastic model.The L-H parameters for the RVBRM are obtained using analytical approaches,composite mechanics,and known parameters of the rock mass and bolt.Using the L-H approach,the reinforcement effect of the fully grouted bolt on the bolted rock specimen and the surrounding rock mass in Jinping II Diversion Tunnel#2 with a depth greater than 2000 m is simulated.The results show that the predictions of the L-H approach are more in agreement with the physical model results of bolted rock specimen and provide a more realistic response of the bolted surrounding rock mass.The L-H approach demonstrates that fully grouted bolts with common bolt spacings and diameters substantially enhance the elastic modulus,shear strength,and tensile strength of the rock mass in the direction of the bolt axis.展开更多
The bolt anchoring force is closely related to the shear properties of the anchor interface. The shear stress distribution of full-length grouted bolts is analyzed based on the stress-strain relationship among the bol...The bolt anchoring force is closely related to the shear properties of the anchor interface. The shear stress distribution of full-length grouted bolts is analyzed based on the stress-strain relationship among the bolt, grout, rock mass and bond interface,considering the shear properties of the grout and contact interface bonding behavior. In this case, the interfacial shear stress of the grout and rock mass and the bolt axial force are obtained under pull-out and normal working conditions. The results show that the peak shear stress of the interface with the shear deformation of the bond interface is significantly lower than that without it when the pull-out force is applied. When designing bolt parameters of grade IV and V rock mass, the relative deformation between the rock mass and anchor should be considered, with a “unimodal” to “bimodal” shear stress distribution.In the case of a low elastic modulus of rock masses,both the shear stress concentration and distribution range are obvious, and the neutral point is near the bolt head. As the elastic modulus increases, the shear stress concentration and distribution range are reduced, and the neutral point moves towards the distal end. As a result, the optimum length of fulllength grouted bolts can be determined by in-situ pull-out tests and decreases with the increased elastic modulus of the rock mass.展开更多
This paper proposes a new interface constitutive model for fully grouted rock-bolts and cable-bolts based on pull-out test results.A database was created combining published experimental data with in-house tests.By me...This paper proposes a new interface constitutive model for fully grouted rock-bolts and cable-bolts based on pull-out test results.A database was created combining published experimental data with in-house tests.By means of a comprehensive framework,a Coulomb-type failure criterion accounting for friction mobilization was defined.During the elastic phase,in which the interface joint is not yet created,the proposed model provides zero radial displacement,and once the interface joint is created,interface dilatancy is modeled using a non-associated plastic potential inspired from the behavior of rock joints.The results predicted by the proposed model are in good agreement with experimental results.The model has been implemented in a finite element method(FEM)code and numerical simulations have been performed at the elementary and the structural scales.The results obtained provide confidence in the ability of the new model to assist in the design and optimization of bolting patterns.展开更多
The grouted bolt,combining rock bolting with grouting techniques,provides an effective solution for controlling the surrounding rock in deep soft rock and fractured roadways.It has been extensively applied in numerous...The grouted bolt,combining rock bolting with grouting techniques,provides an effective solution for controlling the surrounding rock in deep soft rock and fractured roadways.It has been extensively applied in numerous deep mining areas characterized by soft rock roadways,where it has demonstrated remarkable control results.This article systematically explores the evolution of grouted bolting,covering its theoretical foundations,design methods,materials,construction processes,monitoring measures,and methods for assessing its effectiveness.The overview encompassed several key elements,delving into anchoring theory and grouting reinforcement theory.The new principle of high pretensioned high-pressure splitting grouted bolting collaborative active control is introduced.A fresh method for dynamic information design is also highlighted.The discussion touches on both conventional grouting rock bolts and cable bolts,as well as innovative grouted rock bolts and cables characterized by their high pretension,strength,and sealing hole pressure.An examination of the merits and demerits of standard inorganic and organic grouting materials versus the new inorganic–organic composite materials,including their specific application conditions,was conducted.Additionally,the article presents various methods and instruments to assess the support effect of grouting rock bolts,cable bolts,and grouting reinforcement.Furthermore,it provides a foundation for understanding the factors influencing decisions on grouted bolting timing,the sequence of grouting,the pressure applied,the volume of grout used,and the strategic arrangement of grouted rock bolts and cable bolts.The application of the high pretensioned high-pressure splitting grouted bolting collaborative control technology in a typical kilometer-deep soft rock mine in China—the soft coal seam and soft rock roadway in the Kouzidong coal mine,Huainan coal mining area,was introduced.Finally,the existing problems in grouted bolting control technology for deep soft rock roadways are analyzed,and the future development trend of grouted bolting control technology is anticipated.展开更多
Automatically formed roadway(AFR)by roof cutting with bolt grouting(RCBG)is a new deep coal mining technology.By using this technology,the broken roadway roof is strengthened,and roof cutting is applied to cut off str...Automatically formed roadway(AFR)by roof cutting with bolt grouting(RCBG)is a new deep coal mining technology.By using this technology,the broken roadway roof is strengthened,and roof cutting is applied to cut off stress transfer between the roadway and gob to ensure the collapse of the overlying strata.The roadway is automatically formed owing to the broken expansion characteristics of the collapsed strata and mining pressure.Taking the Suncun Coal Mine as the engineering background,the control effect of this new technology on roadways was studied.To compare the law of stress evolution and the surrounding rock control mechanisms between AFR and traditional gob-side entry driving,a comparative study of geomechanical model tests on the above methods was carried out.The results showed that the new technology of AFR by RCBG effectively reduced the stress concentration of the roadway compared with gob-side entry driving.The side abutment pressure peak of the solid coal side was reduced by 24.3%,which showed an obvious pressure-releasing effect.Moreover,the position of the side abutment pressure peak was far from the solid coal side,making it more beneficial for roadway stability.The deformation of AFR surrounding rock was also smaller than the deformation of the gob-side entry driving by the overload test.The former was more beneficial for roadway stability than the latter under higher stress conditions.Field application tests showed that the new technology can effectively control roadway deformation.Moreover,the technology reduced roadway excavation and avoided resource waste caused by reserved coal pillars.展开更多
基金support of the National Basic Research 973 Program of China (No.2013CB036003)the National Natural Science Foundation of China (No.51374198)the National Natural Science Foundation young investigator grant program of China (Nos.51204163,51504247,and 51404255)
文摘By applying experimental method, the bolt stress and supporting mechanism is studied during the deformation process of a rock mass containing a weak interlayer. The force measuring bolt is installed manually and instrumented five pairs of symmetrical strain gauges. The experimental results show that the fully grouted bolt suffers tensile, compressive, bending and shear stress at the same time. The bolt stress evolution is closely related to the deformation stages of the rock mass which are very gradually varying stage, gradually varying stage at the pre-peak and suddenly varying stage at the post peak stage.The axial compressive stress in the bolt is mainly induced by the moment. Thus, in most cases the axial compressive stress is distributed on one side of the bolt. For axial stresses, induced by the axial force and the bending moment at the post-peak stage, three types of changing are observed, viz. increasingincreasing type, decreasing-increasing type and increasing-decreasing type. The stress characteristics of the bolt section in the weak interlayer are significantly different from those in the hard rock. The failure models of the anchored bolt are tensile failure and shear failure, respectively. The bolt not only provides constraints on the free surface of the rock mass, but also resists the axial and lateral loading by the bending moment. This study provides valuable guidelines for bolting support design and its safety assessment.
基金funded by the National Natural Science Foundation of China(Nos.51979268,U1765206,and 52079027)。
文摘Fully grouted bolts are a key component of the support system for underground openings.Although considerable effort has been made in the simulation of the reinforcement effect of the fully grouted bolts on the rock masses surrounding underground openings,most of the work has limited significance since the structural element approach is used.This study proposes a local homogenization approach(L-H approach)that integrates elastoplastic mechanics,composite mechanics,and analytical approaches with numerical simulation to effectively simulate the reinforcement effect of the fully grouted bolt on deep surrounding rock masses.In the L-H approach,the representative volume of bolted rock mass(RVBRM)with a fully grouted bolt is established based on the original mesh model utilized in the rockbolt element approach.The RVBRM is a regular quadrangular prism with a cross-sectional size equal to the bolt spacing and a length equal to the bolt length.The RVBRM is homogenized by the L-H approach from a unidirectional bolt-reinforced composite into a homogeneous transversely isotropic medium whose mechanical properties are described by a new transversely isotropic elastoplastic model.The L-H parameters for the RVBRM are obtained using analytical approaches,composite mechanics,and known parameters of the rock mass and bolt.Using the L-H approach,the reinforcement effect of the fully grouted bolt on the bolted rock specimen and the surrounding rock mass in Jinping II Diversion Tunnel#2 with a depth greater than 2000 m is simulated.The results show that the predictions of the L-H approach are more in agreement with the physical model results of bolted rock specimen and provide a more realistic response of the bolted surrounding rock mass.The L-H approach demonstrates that fully grouted bolts with common bolt spacings and diameters substantially enhance the elastic modulus,shear strength,and tensile strength of the rock mass in the direction of the bolt axis.
基金funded by the Natural Science Foundation of China(Grants Nos.52179113,42207199,41831278)。
文摘The bolt anchoring force is closely related to the shear properties of the anchor interface. The shear stress distribution of full-length grouted bolts is analyzed based on the stress-strain relationship among the bolt, grout, rock mass and bond interface,considering the shear properties of the grout and contact interface bonding behavior. In this case, the interfacial shear stress of the grout and rock mass and the bolt axial force are obtained under pull-out and normal working conditions. The results show that the peak shear stress of the interface with the shear deformation of the bond interface is significantly lower than that without it when the pull-out force is applied. When designing bolt parameters of grade IV and V rock mass, the relative deformation between the rock mass and anchor should be considered, with a “unimodal” to “bimodal” shear stress distribution.In the case of a low elastic modulus of rock masses,both the shear stress concentration and distribution range are obvious, and the neutral point is near the bolt head. As the elastic modulus increases, the shear stress concentration and distribution range are reduced, and the neutral point moves towards the distal end. As a result, the optimum length of fulllength grouted bolts can be determined by in-situ pull-out tests and decreases with the increased elastic modulus of the rock mass.
基金supported by the Research Fund for Coal and Steel(RFCS)in the context of the European project Advancing Mining Support Systems to Enhance the Control of Highly Stressed Ground(AMSSTED)。
文摘This paper proposes a new interface constitutive model for fully grouted rock-bolts and cable-bolts based on pull-out test results.A database was created combining published experimental data with in-house tests.By means of a comprehensive framework,a Coulomb-type failure criterion accounting for friction mobilization was defined.During the elastic phase,in which the interface joint is not yet created,the proposed model provides zero radial displacement,and once the interface joint is created,interface dilatancy is modeled using a non-associated plastic potential inspired from the behavior of rock joints.The results predicted by the proposed model are in good agreement with experimental results.The model has been implemented in a finite element method(FEM)code and numerical simulations have been performed at the elementary and the structural scales.The results obtained provide confidence in the ability of the new model to assist in the design and optimization of bolting patterns.
基金the National Natural Science Foundation of China(Nos.52304141 and 52074154)。
文摘The grouted bolt,combining rock bolting with grouting techniques,provides an effective solution for controlling the surrounding rock in deep soft rock and fractured roadways.It has been extensively applied in numerous deep mining areas characterized by soft rock roadways,where it has demonstrated remarkable control results.This article systematically explores the evolution of grouted bolting,covering its theoretical foundations,design methods,materials,construction processes,monitoring measures,and methods for assessing its effectiveness.The overview encompassed several key elements,delving into anchoring theory and grouting reinforcement theory.The new principle of high pretensioned high-pressure splitting grouted bolting collaborative active control is introduced.A fresh method for dynamic information design is also highlighted.The discussion touches on both conventional grouting rock bolts and cable bolts,as well as innovative grouted rock bolts and cables characterized by their high pretension,strength,and sealing hole pressure.An examination of the merits and demerits of standard inorganic and organic grouting materials versus the new inorganic–organic composite materials,including their specific application conditions,was conducted.Additionally,the article presents various methods and instruments to assess the support effect of grouting rock bolts,cable bolts,and grouting reinforcement.Furthermore,it provides a foundation for understanding the factors influencing decisions on grouted bolting timing,the sequence of grouting,the pressure applied,the volume of grout used,and the strategic arrangement of grouted rock bolts and cable bolts.The application of the high pretensioned high-pressure splitting grouted bolting collaborative control technology in a typical kilometer-deep soft rock mine in China—the soft coal seam and soft rock roadway in the Kouzidong coal mine,Huainan coal mining area,was introduced.Finally,the existing problems in grouted bolting control technology for deep soft rock roadways are analyzed,and the future development trend of grouted bolting control technology is anticipated.
基金This work was supported by the National Natural Science Foundation of China(Nos.51874188,52074164,42077267,and 51927807)the Natural Science Foundation of Shandong Province,China(Nos.2019SDZY04 and ZR2020JQ23)the Project of Shandong Province Higher Educational Youth Innovation Science and Technology Program,China(No.2019KJG013).
文摘Automatically formed roadway(AFR)by roof cutting with bolt grouting(RCBG)is a new deep coal mining technology.By using this technology,the broken roadway roof is strengthened,and roof cutting is applied to cut off stress transfer between the roadway and gob to ensure the collapse of the overlying strata.The roadway is automatically formed owing to the broken expansion characteristics of the collapsed strata and mining pressure.Taking the Suncun Coal Mine as the engineering background,the control effect of this new technology on roadways was studied.To compare the law of stress evolution and the surrounding rock control mechanisms between AFR and traditional gob-side entry driving,a comparative study of geomechanical model tests on the above methods was carried out.The results showed that the new technology of AFR by RCBG effectively reduced the stress concentration of the roadway compared with gob-side entry driving.The side abutment pressure peak of the solid coal side was reduced by 24.3%,which showed an obvious pressure-releasing effect.Moreover,the position of the side abutment pressure peak was far from the solid coal side,making it more beneficial for roadway stability.The deformation of AFR surrounding rock was also smaller than the deformation of the gob-side entry driving by the overload test.The former was more beneficial for roadway stability than the latter under higher stress conditions.Field application tests showed that the new technology can effectively control roadway deformation.Moreover,the technology reduced roadway excavation and avoided resource waste caused by reserved coal pillars.