Operation Performance of Central Solar Heating System with Seasonal Storage Water Tank in Harbin

This paper presented a preliminary research on the central solar heating system with seasonal storage(CSHSSS)used in cold climate in China.A mathematical model of the solar energy seasonal storage water tank used in the central solar heating system was firstly developed based on energy conservation.This was followed by the simulation of the CSHSSS used in a two-floor villa in Harbin,and analysis of the impacts on storage water temperature of tank volume,solar collector area,tank burial depth,insulation thickness around the tank,etc.The results show there is a relatively economical tank volume to optimize the system efficiency,which decreases with increasing tank volume at the constant collector area,and increases with increasing collector area at the constant tank volume.Furthermore,the insulation thickness has obvious effect on avoiding heat loss,while the tank burial depth doesn't.In addition,the relationship between the solar collector efficiency and storage water temperature is also obtained,it decreases quickly with increasing storing water temperature,and then increases slowly after starting space heating system.These may be helpful for relevant design and optimization in cold climates in China and all over the world.

Experimental Investigation on Solution Regeneration Performance and Coefficients in Full-Open System for Heat and Water Recovery of Flue Gas

The recovery of heat and water from low-grade flue gas is of considerable importance for energy conservation and environmental preservation.While the full-open absorption heat pump shows promise as a means of achieving heat and water recovery,the lack of research on heat and mass transfer performance of open-type solution evaporation regeneration represents a significant impediment to its design and operation.This paper experimentally investigates the regeneration performance of an open-type spaying tower equipped with ceramic structured packings.Two different regeneration modes are proposed,namely ambient air receiver mode and flue gas receiver mode,to utilize air or low-grade flue gas as a driving source.The impact of different input parameters on the regeneration characteristics,including heat transfer capacity,water removal rate,thermal efficiency,and humidity effectiveness,are demonstrated.The findings indicate that the enhancement of regeneration can be achieved through the increase of solution flow rate,solution temperature,and flue gas flow rate in both regeneration modes.However,high solution concentration and flue gas humidity ratio can weaken water removal rates and reduce thermal efficiency.For the regeneration of CaCl_(2)-H_(2)O with a concentration of55%,flue gas around 200℃with a humidity ratio below 44 g/kg can successfully drive the solution regeneration process.When the solution concentration or flue gas humidity ratio continues to rise,additional energy is necessary for regeneration.Furthermore,the coupled heat and mass transfer coefficients are fitted,which can contribute to the design and optimization of the open-type regenerator.

Numerical Analysis of Phase Change and Container Materials for Thermal Energy Storage in the Storage Tank of Solar Water Heating System

This study evaluates the effectiveness of phase change materials(PCMs) inside a storage tank of warm water for solar water heating(SWH) system through the theoretical simulation based on the experimental model of S.Canbazoglu et al.The model is explained by five fundamental equations for the calculation of various parameters like the effectiveness of PCMs,the mass of hot water,total heat content,and duration of charging.This study simulated eleven PCMs to analyze their effectiveness like Sodium hydrogen phosphate dodecahydrate(SHPD),OM 37,N-Eicosane(NE),Lauric acid(LA),Paraffin wax(PW),OM 48,Paraffin wax C_(20-33)(PW-C20-33),Sodium acetate trihydrate(SAT),Palmitic acid(PA),Myristic acid(MA),and Stearic acid(SA).Among all PCMs,the SHPD has found the highest value of effectiveness factor of 3.27.So,it is the most recommended PCM for the storage tank of the SWH system.The study also includes the melt fraction analysis of all enumerated PCMs corresponding to container materials of stainless steel,glass,aluminum mixed,tin,aluminum,and copper.This melt fraction analysis is performed by making a coding program in the FORTRAN programming language.Through the analysis,copper container material is found to have high melting rate for all PCMs so it is superior to other container materials.

Effects of biodegradable mulch on soil water and heat conditions,yield and quality of processing tomatoes by drip irrigation

To combat the problem of residual film pollution and ensure the sustainable development of agriculture in oasis areas,a field experiment was carried out in 2019 at the Wuyi Farm Corps Irrigation Center Test Station in Urumqi,Northwest China.Four types of biodegradable mulches,traditional plastic mulchs and a control group(bare land;referred to as CK)were compared,including a total of six different treatments.Effects of mulching on soil water and heat conditions as well as the yield and quality of processing tomatoes under drip irrigation were examined.In addition,a comparative analysis of economic benefits of biodegradable mulches was performed.Principal component analysis and gray correlation analysis were used to evaluate suitable mulching varieties for planting processing tomatoes under drip irrigation.Our results show that,compared with CK,biodegradable mulches and traditional plastic mulch have a similar effect on retaining soil moisture at the seedling stage but significantly increase soil moisture by 0.5%-1.5%and 1.5%-3.0%in the middle and late growth periods(P<0.050),respectively.The difference in the thermal insulation effect between biodegradable mulch and plastic mulch gradually reduces as the crop grows.Compared with plastic mulch,the average soil temperature at 5-20 cm depth under biodegradable mulches is significantly lowered by 2.04°C-3.52°C and 0.52°C-0.88°C(P<0.050)at the seedling stage and the full growth period,respectively,and the water use efficiency,average fruit yield,and production-investment ratio under biodegradable mulches were reduced by 0.89%-6.63%,3.39%-8.69%,and 0.51%-6.33%(P<0.050),respectively.The comprehensive evaluation analysis suggests that the black oxidized biological double-degradation ecological mulch made from eco-benign plastic is the optimal film type under the study condition.Therefore,from the perspective of sustainable development,biodegradable mulch is a competitive alternative to plastic mulch for large-scale tomato production under drip irrigation in the oasis.

Modelling plant canopy effects on water-heat exchange in the freezingthawing processes of active layer on the Qinghai-Tibet Plateau

The effect of vegetation on the water-heat exchange in the freezing-thawing processes of active layer is one of the key issues in the study of land surface processes and in predicting the response of alpine ecosystems to climate change in permafrost regions. In this study, we used the simultaneous heat and water model to investigate the effects of plant canopy on surface and subsurface hydrothermal dynamics in the Fenghuoshan area of the QinghaiTibet Plateau by changing the leaf area index(LAI) and keeping other variables constant. Results showed that the sensible heat, latent heat and net radiation are increased with an increase in the LAI. However, the ground heat flux decreased with an increasing LAI. The annual total evapotranspiration and vegetation transpiration ranged from-16% to 9% and-100% to 15%, respectively, in response to extremes of doubled and zero LAI, respectively. There was a negative feedback between vegetation and the volumetric unfrozen water content at 0.2 m through changing evapotranspiration. The simulation results of soil temperature and moisture suggest that better vegetation conditions are conducive to maintaining the thermal stability of the underlying permafrost, and the advanced initial thawing time and increasing thawing rate of soil ice with the increase in the LAI may have a great influence on the timing and magnitude of supra-permafrost groundwater. This study quantifies the impact of vegetation change on surface and subsurface hydrothermal processes and provides a basic understanding for evaluating the impact of vegetation degradation on the water-heat exchange in permafrost regions under climate change.

Different discretization method used in coupled water and heat transport mode for soil under freezing conditions

A coupled water and heat transport mode is established based on the Richards equation to study water flow and heat transport in soil during freezing process. Both the finite difference and finite element method are used in the discretization, respectively. Two different computer programs are written and used to simulate an indoor unidirectional frozen test. The freezing depth, freezing rate and temperature variation are compared among lab tests, finite difference calculation simulation and finite element calculation simulation. Result shows that： the finite difference method has a better performance in freezing depth simulation while the finite element method has a better performance in numerical stability in one-dimensional freezing simulation.

Energy Efficient Air Conditioning System Using Geothermal Cooling-Solar Heating in Gujarat, India

It is well known that one unit of electrical energy saved is equal to more than two units produced. One way of economizing the power is utilization of energy efficient systems at all locations. In the present study, the air conditioning system is analysed and an innovative way is suggested. We use natural low temperature of shallow sub surface (1 - 3 m) of the earth—geothermal cooling system. It is known that majority of the households and the apartment complexes in India have two tanks for water storage. One is the underground water sump and the other is the overhead water tank. In our study, we use these two water storage systems for space cooling during summer and also for heating during winter. The main aim of our paper is air-conditioning of the space in an economic way to save electricity. It is based on a simple idea of transferring the low temperature from underground water sump to the room in the house using water as a mode of transport. Since India is a tropical country located at low latitude, most of the year, the air temperature is high and demands space cooling. However, for a couple of months during severe winter months (Dec.-Jan.) at Ahmedabad, heating of the space is required. For heating the space, we suggest to use the well-known solar water heater. Effective use of heat exchanger is shown through computation, modelling schemes and lab experiment. We recommend geothermal cooling for 10 months in a year and solar hot water system during 2 months of winter. It is observed that the ambient air temperature of 35°C - 40°C in the room can be brought down to 26°C without much consumption of electricity. In a similar manner, the room temperature at night (13°C) during winter in Ahmedabad can be increased to 27°C through circulation of water from solar water heater in the heat exchanger.

Heating of Nanosized Liquid Water in High-Intensity Terahertz Pulses

Non-equilibrium molecular dynamics simulations of liquid water in picosecond high-power terahertz pulses are performed by using a non-polarizable potential model. Numerical results show that the energy absorption of water molecules exhibits a pronounced resonance with THz pulses in the frequency range of 14-17 THz. With the THz pulse at resonant frequencies, the maximum temperature is about 562 K by heating the water at room temperature. Further investigation indicates that the results are independent of the size of the nanoscale water box. The efficiency of energy transfer by resonant absorption is more than seven times of microwave heating. These studies show promising applications of ultrashort THz pulses.

Life cycle cost analysis of new FRP based solar parabolic trough collector hot water generation system

Parabolic trough collectors (PTCs) are employed for a variety of applications including steam generation and hot water generation. This paper deals with the experimental results and an economic analysis of a new fibre reinforced plastic (FRP) based solar PTC with an embedded electronic controlled tracking system designed and developed for hot water generation in a restaurant in Madurai, India. The new collector performance has been tested according to ASHRAE Standard 93 (1986). The performance of a new PTC hot water generation system with a well mixed hot water storage tank is investigated by a series of extensive tests over ten months period. The average maximum storage tank water temperature observed was 74.91 °C, when no energy is withdrawn from the tank to the load during the collection period. The total cost of the new economic FRP based solar PTC for hot water generation with an embedded electronic controlled tracking system is Rs. 25000 (US$ 573) only. In the present work, life cycle savings (LCS) method is employed for a detailed economic analysis of the PTC system. A computer program is used as a tool for the economic analysis. The present worth of life cycle solar savings is evaluated for the new solar PTC hot water generation system that replaces an existing electric water heating system in the restaurant and attains a value of Rs. 23171.66 after 15 years, which is a significant saving. The LCS method and the MATLAB computer simulation program presented in this paper can be used to estimate the LCS of other renewable energy systems.

Recent Progresses on Optimal Design of Heat Integrated Water Allocation Network

Energy integration and mass integration are important approaches to achieve energy saving and emission reduction in the process industry.Generally,the methods can be classified into two groups,viz.:conceptual design methods and mathematical programming methods.The former includes mainly graphical methods based on pinch technology that is operated easily.A feasible solution can be quickly obtained.Conceptual design methods are sequential in nature including two steps,namely:targeting and designing.The latter is based on superstructure optimization,and corresponding algorithm is adopted to solve the model.The trade-offs and connections among the entire network can be established and explored.Multiple factors can be considered and optimized simultaneously by mathematical programming methods.This paper describes the synthesis of heat integrated water allocation networks(HIWAN)based on both conceptual design methods and mathematical programming methods systematically.In addition,the characteristics and shortcomings of the existing research methods are summarized,and the future research direction is prospected.

Overview of China's National Standards for Solar Water Heating

Introduction Energy supply is one of the major challenges facing China. The rate at which demand is outstripping supply led the Standing Committee of the National People's Congress to pass the Renewable Energy Law of the PRC at its fourteenth session in February, 2005.……

Heat resistance and water protection effectiveness for large single-pane fireproof glass

The effects and heat transfer mode of water film and sprinkler system on the heat-resistant property associated with the insulation of a fireproof glass were investigated. In the experiments, fireproof glass with a size of 3 300 mm (height) × 2 200 mm (width) × 12 mm (thickness) was exposed to an oil pool fire with a power of approximately 1.4 MW. The experimental results show that the application of the water film or sprinkler system on the glass can effectively resist the intensive heat from the fire in the test due to the absorption of latent heat. The permitted period of integrity and insulation with a water film and a sprinkler system could be extended to 60 min. It should be noted that the temperature of the glass surface can be kept under 60 °C in a 60 min test. The experimental results suggest that it is feasible to substitute fireproof glass with water film for a fireproof door as long as the water film or sprinkler system can work stably and water can cover the whole surface of the fireproof glass.

中深层地埋管热泵供热系统运行特性实测研究

通过大量工程实测研究,总结了中深层地埋管热泵供热技术的运行特性。中深层地埋管具有出水温度高、取热功率大、长期运行稳定的特点,为热泵系统提供了高品位的低温热源,以提升其运行性能;同时中深层地埋管自身存在间歇蓄热特性,能很好地满足建筑供热需求变化与柔性用能;无级变频热泵机组更适合与中深层地埋管匹配运行,节能减排效果显著;热源侧水系统具有小流量、大扬程,且阻力随着流量变化而大幅度变化的特性。研究结果可为提升该技术的供热性能提供关键指导。

Comparison and Performance Analysis of Heat Storage Equipment in Solar Heating System

Solar heating system is widely used recently.Heat storage equipment is the guarantee for steady performance of solar heating system.A design of latent heat storage exchanger with submerged coil was introduced with the structure,working principle,and the main advantages.This heat exchanger was integrated into solar heating system as the heat storage equipment.Advantage comparison of the designed heat exchanger in solar heating system with hot water tank was carried out.The analysis results show that the latent heat storage exchanger is superior to hot water tank obviously.The heat exchanger performance parameters and variations of these parameters are got:(1)with the increase of phase change material(PCM)volume ratio,heat storage equipment volume ratio decreases;(2)heat storage efficiency has the same varying tendency with outdoor and air temperature;while the bigger PCM volume ratio is,the weaker the effect of outdoor air temperature on heat storage efficiency is;(3)heat storage capacity and heat storage efficiency increase together;when PCM volume ratio is big,heat storage efficiency is high and the system can begin operating efficiently and quickly;(4)with the increase of heat storage capacity,life cycle operation cost(LCOC)of system increases gradually in high speed;but with the increase of PCM volume ratio,the difference between the two systems LCOCs becomes smaller and smaller;(5)the reasonable range of PCM volume ratio is 0.5-0.7.Temperature characteristic analysis shows that,with the filled PCM,heat storage medium temperature presents several segments at different time,under conditions of different heat storage capacity and different PCM state.

换热站并联水泵分布式优化控制

针对现有换热站并联水泵优化算法在集中式架构下控制适应性不足的问题,本文提出了一种改进的分布式并联水泵优化算法.首先,建立了并联水泵的分布式控制系统,并对该优化问题的数学模型进行描述,在目标函数中引入自适应非线性因子;然后,设计了改进的分布式果蝇优化算法,在该算法中每台水泵的控制器仅通过与邻居控制器交互信息即可完成并联水泵的优化;并且,在嗅觉搜索阶段,使用正弦余弦策略替代赋予个体距离与方向的随机策略;最后,以两个实际换热站中不同并联水泵系统为例对算法进行仿真验证,并基于仿真结果进行性能分析.结果表明,相较于传统算法,改进的分布式果蝇优化算法能得到更优的控制策略,有着收敛速度快、稳定性好和鲁棒性强的特点;并且该算法适用于不同系统的并联水泵优化问题,具有可扩展性.在实际工程验证中相较于集中式算法,该算法在总功率和计算时间上分别平均降低了5.47%和29.90%,因此,能够满足实际换热站中对并联水泵热负荷优化分配的需求.

24h全日集中空气源热泵热水系统贮热水箱容积的分析探讨

在空气源热泵热水系统设计中,贮热水箱容积的计算至关重要。介绍并分析了现行标准规程贮热水箱容积的计算公式,指出了公式运用时可能存在的问题。针对空气源热泵定时运行、24 h全日集中热水供应系统,根据热泵运行时间与用水高峰持续时段的覆盖关系,分情况分析并推导了贮热水箱容积的计算公式。在设计取值范围内,对上述推导公式计算的贮热水箱容积进行了分析。提出了贮热水箱容积在方案阶段的估算建议值。

Performance and Optimization of Air Source Heat Pump Water Heater with Cyclic Heating

A new type of microchannel condenser applied in the air source heat pump water heater(ASHPWH)with cyclic heating was proposed in this study.The operating performance of the ASHPWH was frst tested.Then,the structure of the microchannel condenser was optimized with the implement of vortex generators.Finally,a numerical model of the ASHPWH was established and the optimized microchannel condenser was studied.The experimental results showed that the average coefficient of performance(COP)of the 1HP(735 W)ASHPWH reached 3.48.In addition,the optimized microchannel condenser could be matched with a 3 HP(2430W)ASHPWH with an average heating capacity of 10.30 kW,and achieving an average COP of 4.24,14.6%higher than the limit value in the national standard.

科尔沁沙地沙丘生态系统水热通量特征及影响驱动因子

以科尔沁沙地的典型沙丘区为研究对象,利用涡动相关系统(EC)持续监测沙丘生态系统2013~2022年的表面能量通量数据,采用普通最小二乘线性回归法(OLS)和表面能量平衡比率(EBR)两个指标评估能量平衡闭合度,对沙丘生态系统生长季(4~10月)能量通量的日变化、季节变化以及年际变化进行分析,并计算波文比(β)和能量平衡比,探讨了影响潜热通量(LE)、感热通量(H)和土壤热通量(G)变化的环境因素.结果表明:多年平均年净辐射(R_(g))为1592.77MJ/m^(2),其中H、LE和G分别为614.60,636.22和117.76MJ/m^(2),科尔沁沙地沙丘生态系统年能量的主要组成部分为潜热通量,占总能量的40%.β日动态曲线呈单峰变化,波动相对较平缓.各年年均表面能量平衡比率(EBR)介于0.75~0.90之间,多年年均EBR为0.87,说明能量平衡闭合度的残差为13%.研究表明饱和水汽压差(VPD)是影响能量通量的主要因素,其次是空气温度(T_a)和土壤温度(T_s),均与能量通量呈显著正相关;而植被对能量通量的影响表现在LE与叶面积指数(LAI)呈正相关,而H相反.

一种带光伏直流水泵的太阳能热水器热性能研究

对一套安装光伏直流水泵的横双排分离式全玻璃真空管太阳能热水系统的热性能进行试验,分析了光伏直流水泵对太阳能热水器热性能的影响.结果表明,与常规的自然循环系统相比,光伏直流水泵会使太阳能热水系统的日有用得热量减少0.77 MJ/m^(2),热效率降低4.5%,但贮热水箱内水温分布较均匀,贮热水箱上、下层热水的平均温差仅为1.46℃.