SIMULATION OF STEEL COIL HEAT TRANSFER IN HPH FURNACE

The mathematical model has been estublished for the simulation of steel coil＇s heat transfer during annealing thermal process in HPH （high performance hydrogen） furnace. The equivalent radial thermal conductivity is adopted by statistical analysis regression approach through the combination of a large quantity of production data collected in practice and theoretical analyses. The effect of the number of coils on circulating flow gas is considered for calculating the convection heat transfer coefficient, The temperature within the coil is predicted with the developed model during the annealing cycle including heating process and cooling process. The good consistently between the predicted results and the experimental data has demonstrated that the mathematical model established and the parameters identified by this paper are scientifically feasible and the effective method of calculation for coil equivalent radial heat transfer coefficient and circulating gas flow has been identified successfully, which largely enhances the operability and feasibility of the mathematic- model. This model provides a theoretical basis and an effective means to conduct studies on the impact that foresaid factors may imposed on the steel coil＇s temperature field, to analyze the stress within coils, to realize online control and optimal production and to increase facilily output by increasing heating and cooling rates of coils without producing higher thermal stress.

Steady State Heat Transfer of Ladle Furnace During Steel Production Process

The heat transfer analysis was performed for an industrial ladle furnace （LF） with a capacity of 55-57 t in Turkey. The heat losses by conduction, convection and radiation from outer and bottom surfaces, top and electrodes of LF were determined in detail. Finally, some suggestions about decreasing heat losses were presented.

Numerical simulation of aluminum holding furnace with fluid-solid coupled heat transfer

To predict three-dimensional temperature distribution of molten aluminum and its influencing factors inside an industrial aluminum holding furnace,a fluid-solid coupled method was presented.The fluid-solid coupled mathematics models of aluminum holding furnace in the premixed combustion processing were established based on mass conservation,moment conservation,momentum conservation,energy conservation and chemistry species conservation.Computational results agree well with the test data of the typical condition.The maximum combustion temperature is 1 850 K.The average temperature of the molten aluminum is 1 158 K,and the maximum temperature difference is about 240 K.The average temperature increases 0.3 ℃ while the temperature of combustion air increases 1 ℃.The optimal excess air ratio is 1.25-1.30.

Zonal method solution of radiative heat transfer in a one-dimensional long roller-hearth furnace in CSP

A radiative heat transfer mathematical model for a one-dimensional long furnace was set up in a through-type roller-hearth furnace （TTRHF） in compact strip production （CSP）. To accurately predict the heat exchange in the furnace, modeling of the complex gas energy-balance equation in volume zones was considered, and the heat transfer model of heating slabs and wall lines was coupled with the radiative heat transfer model to identify the surface zonal temperature. With numerical simulation, the temperature fields of gas, slabs, and wall lines in the furnace under one typical working condition were carefully accounted and analyzed. The fundamental theory for analyzing the thermal process in TI＇RI-IF was provided.

Mathematical model on heat transfer of water-cooling steel-stick bottom electrode of DC electric arc furnace

For predicting and controlling the melted depth of bottomelectrode during the process of steelmaking, the water-cooling steel-stick electrode is taken as an example, to analyze the process ofheat transfer, then 3D mathematical model by control capacity methodis built. At the same time, the measurement on the melted depth ofbottom electrode is conducted which verified the correctness of thebuilt mathematical model. On the base of verification, all kinds ofkey parameters are calculated through the application and a series ofresults are simulated. Finally, the optimum parameters are found andthe service life of bottom electrode is prolonged.

Modeling and Simulation of Heat Transfer in Loaded Continuous Heat Treatment Furnace

Continuous furnaces are widely used in the heat treatment of mass-produced parts. However, the heating up process of parts in continuous furnace is still decided by experience. In this paper the heat transfer in the continuous furnace is formulated firstly. The heat balance in each zone is discussed and equations are given. Coupled with the model for heat transfer between workpieces and furnace and the heat transfer in the workload as well presented in the former developed CHT-6/ for batch furnaces, a program CHT- for continuous furnaces was developed. The model deals with two typical movements of parts: continuous or step by step. The moving speed of parts and load pattern can be optimized based on the calculated temperature distributions and curves, especially, the fastest heated and slowest-heated temperature-distance profiles. A case study is carried out for the heat treatment of a kind of hook-shaped part. The calculated results are analyzed and in good agreement with the measured ones.

Calculations of Heat Transfer in Torch Furnaces by Gas Volume Radiation Laws

The results stemming from the calculation of heat transfer in torch furnaces by the laws, relating to radiation from solid surfaces and gas volumes are analyzed. The article presents the laws for radiation from gas volumes and the procedure for calculating heat transfer in torch furnaces, fire boxes, and combustion chambers, elaborated on their basis. The example of heat transfer calculation in a torch furnace is given, and it is significantly non-uniform in nature. Non-uniformity of heat flux distribution on heating surfaces is given. According to the results of calculations, a new furnace is designed to decrease the non-uniformity of ingot heating, fuel rate, and increase the furnace capacity. The calculation results of the distribution of heat fluxes on the heating surfaces are given in changing torch geometric dimensions. These results are confirmed by experimental studies.

Numerical modeling of multiphase flow,heat transfer and titanium flow behavior in blast furnace hearth

Understanding the complex phenomena in BF hearth is essential to increase furnace productivity and to extend furnace campaign.We have developed several continuum-based mathematical/numerical models to simulate the multi-phase flow,heat transfer and chemical reactions in the BF hearth.These models have generated an improved insight on the mechanisms for liquid drainage efficiency,lining erosion and wall protection in BF hearth under operational conditions.The current paper gives an overview of these studies in three aspects:Gas flow and pressure on the liquid surface,and their effect on the drainage characteristics;The flow and temperature distributions of liquid iron in BF hearth,and the temperature distribution in the refractories;Finally,titanium behaviors due to titania injection to form Ti(C,N) -rich scaffold on the hearth surface,to protect the hearth from erosion.

Theory and Practice of Heat Transfer in Electric Arc and Flare Furnaces and Power Plants

The author describes the fundamental laws of physics, the laws of thermal radiation of ionized and non-ionized gas volumes. Based on open laws, a modern theory of heat transfer and methods for calculating heat transfer in electric arc and flare metallurgical furnaces, furnaces of steam boilers, and combustion chambers of gas turbine plants of power plants have been developed. The use of scientific discovery makes it possible to create innovative electric arc steel-smelting furnaces, flare heating furnaces, and combustion chambers in which the consumption of electricity and fuel is reduced, productivity and service life are increased, and the amount of harmful emissions into the environment is reduced.

Numerical Simulation of Heat Transfer of High-Temperature Slag Flow Inside the Blast Furnace Slag Trench

To investigate the flow and heat transfer process of blast furnace slag through the slag trench after the slag is discharged,a three-dimensional physical model is established and simulated according to the actual size of the slag trench and the physical properties of the high-temperature slag.The temperature field and flow field distribution of the high-temperature slag liquid inside the slag trench is obtained by numerical simulation under different working conditions,and the effects of operating conditions such as slag trench inclination,high-temperature slag inlet flow rate,and inlet temperature are investigated.The results show that the flow rate of high-temperature slag is related to the slope of the slag trench,the greater the slope of the slag trench,the higher the flow rate of high-temperature slag,in which the highest average speed can reach 2.23 m/s when the slope is 8%;changing the inlet flow rate,flowing through the slag trench,the high-temperature slag reaches the highest flow rate at the same position,the overall flow rate changes tend to rise first and then decrease,and the greater the inlet flow rate,the higher the temperature change of high-temperature slag.The higher the inlet flow rate,the higher the temperature change of high-temperature slag,the higher the temperature of high-temperature slag out of the slag trench;the higher the inlet temperature,the higher the overall flow rate of high-temperature slag,and the position of the highest flow rate is relatively backward.

A New Experimental Rig of Testing Flow Boiling Heat Transfer of Refrigerantand Lubricant Mixture

This paper proposed a new experimental rig of testing flow boiling heat transfer of refrigerant and lubricant oil mixture. The quantity of oil in the test section can be controlled and regulated conveniently and accurately by connecting separate lubricant oil circuit with test section in parallel. It was built up by retrofitting a multiple air-conditioner and installing three oil-separators in serials at the compressor outlet. And so the lubricant oil in the discharged refrigerant gas of compressor can be removed completely.The refrigerant flow rate through test section can be bypassed by the by-path circuit of indoor unit.This experimental rig has advantages such as on-line and continuous oil injection, short time of obtaining stability, flexible operation, simple control, which lead to high efficiency in the research of flow boiling heat transfer of refrigerant and lubricant oil mixture.

Study of steam heat transfer enhanced by CO_(2) and chemical agents: In heavy oil production

Steam flooding with the assistance of carbon dioxide (CO_(2)) and chemicals is an effective approach for enhancing super heavy oil recovery. However, the promotion and application of CO_(2) and chemical agent-assisted steam flooding technology have been restricted by the current lack of research on the synergistic effect of CO_(2) and chemical agents on enhanced steam flooding heat transfer. The novel experiments on CO_(2)–chemicals cooperate affected steam condensation and seepage were conducted by adding CO_(2) and two chemicals (sodium dodecyl sulfate (SDS) and the betaine temperature-salt resistant foaming agent ZK-05200).According to the experimental findings, a “film” formed on the heat-transfer medium surface following the co-injection of CO_(2) and the chemical to impede the steam heat transfer, reducing the heat transfer efficiency of steam, heat flux and condensation heat transfer coefficient. The steam seepage experiment revealed that the temperature at the back end of the sandpack model was dramatically raised by 3.5–12.8 °C by adding CO_(2) and chemical agents, achieving the goal of driving deep-formation heavy oil. The combined effect of CO_(2) and SDS was the most effective for improving steam heat transfer, the steam heat loss was reduced by 6.2%, the steam condensation cycle was prolonged by 1.3 times, the condensation heat transfer coefficient was decreased by 15.5%, and the heavy oil recovery was enhanced by 9.82%. Theoretical recommendations are offered in this study for improving the CO_(2)–chemical-assisted steam flooding technique.

Influence of furnace temperature and non-uniform heat flux density on direct reduction process of newly designed carbon containing pellet

In this study,innovative ellipsoid pellet with craters on its surface was designed,and the direct reduction process was compared with ellipsoid(without craters)and sphere pellets.In addition,furnace temperature and uneven heat flux density effects on the pellet direct reduction process were also studied.The results show that ellipsoid pellet is better than that of spherical pellet on metallization ratio.However,under the condition of non-uniform heat flow,the ellipsoid pellet final metallization rate and zinc removal rate were lower.Although the heat transfer effect of ellipsoid pellet with craters was not improved significantly,the metallization rate and zinc removal rate were found improved,which will have a cumulative effect on the pellets direct reduction process in rotary hearth furnace.Under varying furnace temperature conditions,the pellet temperature was higher than that of the constant furnace temperature.After 1200 s,pellet Fe concentration increased to 123.6%,metallization rate and zinc removal rate increased to 113.7%and 102.2%,respectively.These results can provide references for the carbon-containing pellet design used in rotary hearth furnace.

Theoretical Derivation of Thermal Value Equations for Heating Furnaces

Based on thermal value theory, the aim of this paper is to deduce the theoretical formulas for evaluating the energy effective utilization degree in technological pyrological processes exemplified by metallurgical heating furnaces. Heat transfer models for continuous heating furnaces, batch-type heating furnaces, and regenerative heating furnaces are established, respectively. By analyzing the movement path of injected infinitesimal heat attached on steel or gas, thermal value equations of continuous, batch-type, and regenerative heating furnaces are derived. Then the influences of such factors as hot charging, gas preheating and intake time of heat on energy effective utilization degree are discussed by thermal value equations. The results show that thermal value rises with hot charging and air preheating for continuous heating furnaces, with shorter intake time when heat is attached on steel or longer intake time when heat is attached on gas for batch-type heating furnaces and that with more heat supply at early heating stage or less at late stage for regenerative heating furnaces.

Identification of Heat Transfer Coefficients by Use Conditions of Quenching Oil

Heat transfer coefficients of the quench medium are necessary for heat-treatment simulation. Cooling characteristics of quenching oil vary with kinds and usage greatly. Users are selecting oil solutions that come up to their desired hardness and quenching distortion requirements. In particular cooling performance rises by agitation and decompression. Therefore we identified a heat transfer coefficient by usage and kinds of quenching oil. Cooling characteristics are different greatly by a kind of quenching oil. A difference of a cooling characteristic by a kind of oil depends on a temperature range of a boiling stage and the maximum heat transfer coefficient mainly. On the other hand, in a convection stage, there are few changes in a boiling stage. Even if quenching oil temperature is changed, heat transfer coefficients do not change greatly. When quenching oil stirred, heat transfer coefficients of vapor blanket stage and a convection stage rise, but there are a few changes in a boiling stage. When quenching oil is decompressed a temperature range of a high heat transfer coefficient moves to the low temperature side. In addition, a heat transfer coefficient in a vapor blanket stage comes down. For precision improvement of heat-treatment simulation, it is important that the heat transfer coefficient is calculated in conformity to the on-site use reality.

Fluid Flow Modeling of Arc Plasma and Bath Circulation in DC Electric Arc Furnace

A mathematical model describing the flow field, heat transfer and the electromagnetic phenomenon in a DC electric arc furnace has been developed. First the governing equations in the arc plasma region are solved and the calculated results of heat transfer, current density and shear stresses on the anode surface are used as boundary conditions in a model of molten bath. Then a two-dimensional time-dependent model is used to describe the flow field and electromagnetic phenomenon in the molten bath. Moreover, the effect of bottom electrode diameter on the circulation of molten bath is studied.

Geologic-Geophysical Indicators of the Deep Structure of Zones of Geothermal Anomalies for Allocation of Channels of the Deep Heat and Mass Transfer

On the basis of the analysis of field thermogeochemical data along abnormal zones of a thermal stream in the Bukhara-Khiva, oil-and-gas region of the Turan (Tegermen, Chagakul, Shimoly Alat, Beshtepa) was succeeded to obtain important data on a deep structure of sites. Data of gas-chemical and geothermal observations show about confinedness of abnormal concentration of methane to zones of the increased values of the temperature field the measured values of temperatures (Tegermen Square and others). On geoelectric section mines 2-D of inversion of the MT-field depth of 4000 m are lower, among very high-resistance the chemogenic and carbonate deposits of the Paleozoic is traced the subvertical carrying-out abnormal zone. This zone is identified as the channel of a deep heat and mass transfer with which hydrocarbon (HC) deposits are connected. It is shown that electro-investigation when using a geophysical complex can and has to become “advancing” at exploration by oil and gas.

Magnetic Oil Thermal Behavior under Electromagnetic Induction for Energy Efficient Heating System Design

This study describes thermal behavior of magnetic lubricant oil under electromagnetic induction. Experimental set up include oil pump, oil tank, induction heating unit, and heat exchanger. It is a closed loop system where the oil pump circulates oil through oil tank to the system, at the same time induction heating unit heats up to the heat exchanger where the lubricant oil thermal behavior is examined. The unit has been largely studied and tested both magnetic and regular motor oil in a laboratory environment and promising results have been obtained for an actual indoor floor to space heating system design.

Mathematical Model and Its Application of Radial Effective Thermal Conductivity for Coil Heat Transfer in HPH Furnace

Temperature uniformity of steel coils in High Performance Hydrogen bell-type annealing furnace has a significant effect on their quality and production. The hot rolled coil can be considered as a periodically laminated material composed of steel layers and interface layers in radial direction. A new formula for the radial effective thermal conductivity has been proposed, which is based on surface characteristic, strip thickness and compressive stress of the rolled coil. Furthermore, it has been used to develop a heat transfer mathematical model for steel coils in the HPH furnace. The calculated annealing curves using this mathematical model are in good agreement with the experimental data.

Numerical simulation of downhole temperature distribution in producing oil wells

An improved numerical simulation method is presented to calculate the downhole temperature distribution for multiple pay zones in producing oil wells. Based on hydrodynamics and heat transfer theory, a 2-D temperature field model in cylindrical coordinates is developed. In the model, we considered general heat conduction as well as the heat convection due to fluid flow from porous formation to the borehole. We also take into account the fluid velocity variation in the wellbore due to multiple pay zones. We present coupled boundary conditions at the interfaces between the wellbore and adjacent formation, the wellbore and pay zone, and the pay zone and adjacent formation. Finally, an alternating direction implicit difference method （ADI） is used to solve the temperature model for the downhole temperature distribution. The comparison of modeled temperature curve with actual temperature log indicates that simulation result is in general quite similar to the actual temperature log. We found that the total production rate, production time, porosity, thickness of pay zones, and geothermal gradient, all have effects on the downhole temperature distribution.