Robot Zero-Moment Control Algorithm Based on Parameter Identification of Low-Speed Dynamic Balance

This paper proposes a zero-moment control torque compensation technique.After compensating the gravity and friction of the robot,it must overcome a small inertial force to move in compliance with the external force.The principle of torque balance was used to realise the zero-moment dragging and teaching function of the lightweight collaborative robot.The robot parameter identification based on the least square method was used to accurately identify the robot torque sensitivity and friction parameters.When the robot joint rotates at a low speed,it can approximately satisfy the torque balance equation.The experiment uses the joint position and the current motor value collected during the whole moving process under the low-speed dynamic balance as the excitation signal to realise the parameter identification.After the robot was compensated for gravity and static friction,more precise torque control was realised.The zero-moment dragging and teaching function of the robot was more flexible,and the drag process was smoother.

Parameters Identification for Extended Debye Model of XLPE Cables Based on Sparsity-Promoting Dynamic Mode Decomposition Method

To identify the parameters of the extended Debye model of XLPE cables,and therefore evaluate the insulation performance of the samples,the sparsity-promoting dynamicmode decomposition(SPDMD)methodwas introduced,aswell the basics and processes of its applicationwere explained.The amplitude vector based on polarization current was first calculated.Based on the non-zero elements of the vector,the number of branches and parameters including the coefficients and time constants of each branch of the extended Debye model were derived.Further research on parameter identification of XLPE cables at different aging stages based on the SPDMD method was carried out to verify the practicability of the method.Compared with the traditional differential method,the simulation and experiment indicated that the SPDMD method can effectively avoid problems such as the relaxation peak being unobvious,and possessing more accuracy during the parameter identification.And due to the polarization current being less affected by the measurement noise than the depolarization current,the SPDMD identification results based on the polarization current spectral line proved to be better at reflecting the response characteristics of the dielectric.In addition,the time domain polarization current test results can be converted into the frequency domain,and then used to obtain the dielectric loss factor spectrum of the insulation.The integral of the dielectric loss factor on a frequency domain can effectively evaluate the insulation condition of the XLPE cable.

Spatiotemporal variations of parameters of internal solitary waves in the northern South China Sea

The dynamic parameters for internal solitary waves(ISWs)derived from the extended Korteweg-de Vries(eKdV)equation play an important role in the understanding and prediction of ISWs.The spatiotemporal variations of the dynamic parameters of the ISWs in the northern South China Sea(SCS)were studied based on the reanalysis of long-term temperature and salinity datasets.The results for spectrum analysis show that there are definite geographical differences for the periodic variation of the parameters:in shallow water,all parameters vary with a wave period of one year,while in deep water wave components of the parameters at other frequencies exist.Using wavelet analysis,the wavelet power spectral densities in deep water exhibited an inter-annual variation pattern.For example,the wave component of the dispersion coefficient with a wave period of about half a year reached its power peak once every two years.Based on previous work,this inter-annual variation pattern was deduced to be caused by dynamic processes.In further work on the regulatory mechanisms,empirical orthogonal function(EOF)decomposition was performed.It was found that the modes of the dispersion coefficient have different geographical distributions,explaining the reason why the wave components in different frequencies appeared in different locations.The numerical simulation results confirm that the variations in the parameters of the ISWs derived from the eKdV equation could affect the waveforms significantly because of changes in the polarity of the ISWs.Therefore,the periodic variations of the dynamic parameters are related to the geographical location because of dynamic processes operating.

Parameter calibration of the tensile-shear interactive damage constitutive model for sandstone failure

The tensile-shear interactive damage(TSID)model is a novel and powerful constitutive model for rock-like materials.This study proposes a methodology to calibrate the TSID model parameters to simulate sandstone.The basic parameters of sandstone are determined through a series of static and dynamic tests,including uniaxial compression,Brazilian disc,triaxial compression under varying confining pressures,hydrostatic compression,and dynamic compression and tensile tests with a split Hopkinson pressure bar.Based on the sandstone test results from this study and previous research,a step-by-step procedure for parameter calibration is outlined,which accounts for the categories of the strength surface,equation of state(EOS),strain rate effect,and damage.The calibrated parameters are verified through numerical tests that correspond to the experimental loading conditions.Consistency between numerical results and experimental data indicates the precision and reliability of the calibrated parameters.The methodology presented in this study is scientifically sound,straightforward,and essential for improving the TSID model.Furthermore,it has the potential to contribute to other rock constitutive models,particularly new user-defined models.

Dynamics and adaptive control of a dual-arm space robot with closed-loop constraints and uncertain inertial parameters

A dynamics-based adaptive control approach is proposed for a planar dual-arm space robot in the presence of closed-loop constraints and uncertain inertial parameters of the payload. The controller is capable of controlling the po- sition and attitude of both the satellite base and the payload grasped by the manipulator end effectors. The equations of motion in reduced-order form for the constrained system are derived by incorporating the constraint equations in terms of accelerations into Kane＇s equations of the unconstrained system. Model analysis shows that the resulting equations perfectly meet the requirement of adaptive controller design. Consequently, by using an indirect approach, an adaptive control scheme is proposed to accomplish position/attitude trajectory tracking control with the uncertain parameters be- ing estimated on-line. The actuator redundancy due to the closed-loop constraints is utilized to minimize a weighted norm of the joint torques. Global asymptotic stability is proven by using Lyapunov＇s method, and simulation results are also presented to demonstrate the effectiveness of the proposed approach.

Dynamic threshold for SPWVD parameter estimation based on Otsu algorithm

Time-frequency-based methods are proven to be effective for parameter estimation of linear frequency modulation （LFM） signals. The smoothed pseudo Winger-Ville distribution （SPWVD） is used for the parameter estimation of multi-LFM signals, and a method of the SPWVD binarization by a dynamic threshold based on the Otsu algorithm is proposed. The proposed method is effective in the demand for the estimation of different parameters and the unknown signal-to-noise ratio （SNR） circumstance. The performance of this method is confirmed by numerical simulation.

Simulation of pedestrian evacuation based on an improved dynamic parameter model

An improved dynamic parameter model is presented based on cellular automata.The dynamic parameters,including direction parameter,empty parameter,and cognition parameter,are formulated to simplify tactically the process of making decisions for pedestrians.The improved model reflects the judgement of pedestrians on surrounding conditions and the action of choosing or decision.According to the two-dimensional cellular automaton Moore neighborhood we establish the pedestrian moving rule,and carry out corresponding simulations of pedestrian evacuation.The improved model considers the impact of pedestrian density near exits on the evacuation process.Simulated and experimental results demonstrate that the improvement makes sense due to the fact that except for the spatial distance to exits,people also choose an exit according to the pedestrian density around exits.The impact factors 伪,尾,and 纬 are introduced to describe transition payoff,and their optimal values are determined through simulation.Moreover,the effects of pedestrian distribution,pedestrian density,and the width of exits on the evacuation time are discussed.The optimal exit layout,i.e.,the optimal position and width,is offered.The comparison between the simulated results obtained with the improved model and that from a previous model and experiments indicates that the improved model can reproduce experimental results well.Thus,it has great significance for further study,and important instructional meaning for pedestrian evacuation so as to reduce the number of casualties.

Infl uence of structural parameters on dynamic characteristics and wind-induced buffeting responses of a super-long-span cable-stayed bridge

A 3D finite element （FE） model for the Sutong cable-stayed bridge （SCB） is established based on ANSYS. The dynamic characteristics of the bridge are analyzed using a subspace iteration method. Based on recorded wind data, the measured spectra expression is presented using the nonlinear least-squares regression method. Turbulent winds at the bridge site are simulated based on the spectral representation method and the FFT technique. The influence of some key structural parameters and measures on the dynamic characteristics of the bridge are investigated. These parameters include dead load intensity, as well as vertical, lateral and torsional stiffness of the steel box girder. In addition, the influence of elastic stiffness of the connection device employed between the towers and the girder on the vibration mode of the steel box girder is investigated. The analysis shows that all of the vertical, lateral and torsional buffeting displacement responses reduce gradually as the dead load intensity increases. The dynamic characteristics and the structural buffeting displacement response of the SCB are only slightly affected by the vertical and torsional stiffness of the steel box girder, and the lateral and torsional buffeting displacement responses reduce gradually as the lateral stiffness increases. These results provide a reference for dynamic analysis and design of super-long-span cable-stayed bridges.

Population parameters and dynamic pool models of commercial fishes in the Beibu Gulf, northern South China Sea

Length-frequency data of eight commercial fish species in the Beibu Gulf （Golf of Tonkin）, northern South China Sea, were collected during 2006-2007. Length-weight relationships and growth and mortality parameters were analyzed using FiSAT II software. Five species had isometric growth, two species had negative allometric growth, and one species had positive allometric growth. Overall, the exploitation rates of the eight species were lower in 2006 2007 than in 1997-1999： for four species （Saurida tumbil, Saurida undosquamis, Argyrosomus macrocephalus, and Nemipterus virgatus） it was lower in 2006-2007 than in 1997 1999, for two species （Parargyrops edita and Trichiurus haumela） it remained the same, and for the other two species （Trachurus japonicus and Decapterus maruadsi） it was higher in 2006~007 than in 1997-1999. The exploitation rates might have declined because of the decline in fishing intensity caused by high crude oil prices. The optimum exploitation rate, estimated using Beverton-Holt dynamic pool models, indicated that although fishes in the Beibu Gulf could sustain high exploitation rates, the under-size fishes at first capture resulted in low yields. To increase the yield per recruitment, it is more effective to increase the size at first capture than to control fishing effort.

Identification of nucleation parameter for cellular automaton model of dynamic recrystallization

The accuracy of nucleation parameter is a critical factor in the simulation of microstructural evolution during dynamic recrystallization(DRX).Based on the flow stress curve under hot deformation conditions,a new approach is proposed to identify the nucleation parameter during DRX.In this approach,a cellular automaton(CA) model is applied to quantitatively simulate the microstructural evolution and flow stress during hot deformation;and adaptive response surface method(ARSM) is applied as optimization model to provide input parameters to CA model and evaluate the outputs of the latter.By taking an oxygen-free high-conductivity(OFHC) copper as an example,the good agreement between the simulation results and the experimental observations demonstrates the availability of the proposed method.

Dynamic modeling and parameter identification of a gun saddle ring

In this study,a theoretical nonlinear dynamic model was established for a saddle ring based on a dynamic force analysis of the launching process and the structure according to contact-impact theory.The ADAMS software was used to build a parameterized dynamic model of the saddle ring.A parameter identification method for the ring was proposed based on the particle swarm optimization algorithm.A loading test was designed and performed several times at different elevation angles.The response histories of the saddle ring with different loads were then obtained.The parameters of the saddle ring dynamic model were identified from statistics generated at a 500 elevation angle to verify the feasibility and accuracy of the proposed method.The actual loading history of the ring at a 70°elevation angle was taken as the model input.The response histories of the ring under these working conditions were obtained through a simulation.The simulation results agreed with the actual response.Thus,the effectiveness and applicability of the proposed dynamic model were verified,and it provides an effective method for modeling saddle rings.

Vertex solution theorem for the upper and lower bounds on the dynamic response of structures with uncertain-but-bounded parameters

The aim of this paper is to evaluate the effects of uncertain-but-bounded parameters on the dynamic response of structures. By combining the interval mathematics and the finite element analysis, the mass matrix, damping matrix, stiffness matrix and the external loads are represented as interval matrices and vector. With the help of the optimization theory, we present the vertex solution theorem for determining both the exact upper bounds or maximum values and the exact lower bounds or minimum values of the dynamic response of structures, in which these parameters reach their extreme values on the boundary of the interval mass, damping, stiffness matrices and the interval extemal loads vector. Three examples are used to illustrate the computational aspects of the presented vertex solution theorem.

Dynamic reliability analysis of supercavity vehicle with stochastic parameters under impact loads

With dynamic reliability problems of stochastic parameters,supercavity vehicle is subject to impact loads.The supercavity vehicle is modeled by using eight-node super-parametric shell elements.The tail impact loads of supercavity vehicle structures are simplified into two stationary random processes with a certain phase difference,and the random excitations are transformed into sinusoidal ones in terms of the pseudo excitation method.The stress response of stochastic structure can be obtained through combining Newmark method with pseudo excitation perturbation method,and then all required digital features for dynamic reliability of supercavity vehicle have be calculated.The expressions of the mean value and the variance of dynamic reliability of supercavity vehicle with stochastic parameters are educed on the basis of the Poisson formula of calculating dynamic reliability.Finally,the influence of the randomness of structural parameters on the dynamic reliability is analyzed.And the feasibility and availability of this method were validated by comparing with the Monte Carlo method.

Influence of Structural Parameters of Turbocharger Floating Bearing on Its Dynamic Characteristic Coefficients

The structure parameters in an actual industrial production have a great influence on the coefficient of supercharger floating bearing dynamic characteristics,but there has been little systematic study so far.In this paper,the influence of structural parameters of the turbocharger floating bearing on its dynamic characteristic coefficientsis systematically investigated based on the theories of hydrodynamic lubrication and tribology.The influence of clearance ratio on eccentricity and the influence of internal to external radius ratios,and Sommerfeld number were analyzed.A new formula of responding characteristics of the oil film force caused by the displacement or velocity disturbance was deduced near an equilibrium in the steady state.Applying the newly developed formula,the dynamic characteristic was studied for floating bearings.Regularity for change of oil film stiffness and damping was analyzed with the structural parameters of floating bearing such as radius ratios and eccentricity.It has been found that the clearance ratio increases with eccentricity when the radius ratio is unchanged.The eccentricity decreases with the internal to external radius ratio of floating rings when the clearance ratio is constant.The absolute value of total principal stiffness and total main damping decrease with the clearance ratio and radius ratio of floating rings when the total cross damping is stable.The results and findings in this paper can contribute to nonlinear dynamics designs of turbocharger rotor-bearing systems.

PARAMETER IDENTIFICATION OF DYNAMIC MODELS USING A BAYES APPROACH

The Bayesian method of statistical analysis has been applied to the parameter identification problem. A method is presented to identify parameters of dynamic models with the Bayes estimators of measurement frequencies. This is based on the solution of an inverse generalized evaluate problem. The stochastic nature of test data is considered and a normal distribution is used for the measurement frequencies. An additional feature is that the engineer's confidence in the measurement frequencies is quantified and incorporated into the identification procedure. A numerical example demonstrates the efficiency of the method.

Identification of dynamic model parameters for lithium-ion batteries used in hybrid electric vehicles

An electrical equivalent circuit model for lithium-ion batteries used for hybrid electric vehicles （HEV） is presented. The model has two RC networks characterizing battery activation and concentration polarization process. The parameters of the model are identified using combined experimental and extended Kalman filter （EKF） recursive methods. The open-circuit voltage and ohmic resistance of the battery are directly measured and calculated from experimental measurements, respectively. The rest of the coupled dynamic parameters, i.e. the RC network parameters, are estimated using the EKF method. Experimental and simulation results are presented to demonstrate the efficacy of the proposed circuit model and parameter identification techniques for simulating battery dynamics.

Harmony search algorithm with differential evolution based control parameter co-evolution and its application in chemical process dynamic optimization

A modified harmony search algorithm with co-evolutional control parameters(DEHS), applied through differential evolution optimization, is proposed. In DEHS, two control parameters, i.e., harmony memory considering rate and pitch adjusting rate, are encoded as a symbiotic individual of an original individual(i.e., harmony vector). Harmony search operators are applied to evolving the original population. DE is applied to co-evolving the symbiotic population based on feedback information from the original population. Thus, with the evolution of the original population in DEHS, the symbiotic population is dynamically and self-adaptively adjusted, and real-time optimum control parameters are obtained. The proposed DEHS algorithm has been applied to various benchmark functions and two typical dynamic optimization problems. The experimental results show that the performance of the proposed algorithm is better than that of other HS variants. Satisfactory results are obtained in the application.

Fabric and Programming of Photoautotrophic Micro-propagation System Controlled by Dynamic Parameters

According to theory of photoautotrophic micro-propagation, and principle and technology of environmental engineering, an automatic control and regulation under photoautotrophic micro-propagation by plants was designed, which can be used for planting condition optimization of photoautotrophic micro-propagation and qualified industrialized production of seedlings.

A Statistical Parameter Analysis and SVM Based Fault Diagnosis Strategy for Dynamically Tuned Gyroscopes

Gyro's fault diagnosis plays a critical role in inertia navigation systems for higher reliability and precision. A new fault diagnosis strategy based on the statistical parameter analysis (SPA) and support vector machine (SVM) classification model was proposed for dynamically tuned gyroscopes (DTG). The SPA, a kind of time domain analysis approach, was introduced to compute a set of statistical parameters of vibration signal as the state features of DTG, with which the SVM model, a novel learning machine based on statistical learning theory (SLT), was applied and constructed to train and identify the working state of DTG. The experimental results verify that the proposed diagnostic strategy can simply and effectively extract the state features of DTG, and it outperforms the radial-basis function (RBF) neural network based diagnostic method and can more reliably and accurately diagnose the working state of DTG.

THEORY AND METHOD OF OPTIMAL CONTROL SOLUTION TODYNAMIC SYSTEM PARAMETERS IDENTIFICATION (Ⅰ)──FUNDAMENTAL CONCEPT AND DETERMINISTIC SYSTEM PARAMETERS IDENTIFICATION

Based on the concept of optimal control solution to dynamic system parameters identification and the optimal control theory of deterministic system,dyna-mics system parameters identfication problem is brought into correspondence with optimal control problem. Then the theory and algorithm of optimal control are introduced into the study of dynamic system parameters identification. According to the theory of Hamilton-Jacobi-Bellman (HJB) equations solution, the existence and uniqueness of optimal control solution to dynamic system parameters identification are resolved in this paper. At last, the parameters identification algorithm of determi-nistic dynamic system is presented also based on above mentioned theory and concept.