Factors Influencing the Spatial Variability of Air Temperature Urban Heat Island Intensity in Chinese Cities

Few studies have investigated the spatial patterns of the air temperature urban heat island(AUHI)and its controlling factors.In this study,the data generated by an urban climate model were used to investigate the spatial variations of the AUHI across China and the underlying climate and ecological drivers.A total of 355 urban clusters were used.We performed an attribution analysis of the AUHI to elucidate the mechanisms underlying its formation.The results show that the midday AUHI is negatively correlated with climate wetness(humid:0.34 K;semi-humid:0.50 K;semi-arid:0.73 K).The annual mean midnight AUHI does not show discernible spatial patterns,but is generally stronger than the midday AUHI.The urban–rural difference in convection efficiency is the largest contributor to the midday AUHI in the humid(0.32±0.09 K)and the semi-arid(0.36±0.11 K)climate zones.The release of anthropogenic heat from urban land is the dominant contributor to the midnight AUHI in all three climate zones.The rural vegetation density is the most important driver of the daytime and nighttime AUHI spatial variations.A spatial covariance analysis revealed that this vegetation influence is manifested mainly through its regulation of heat storage in rural land.

Effects of temperature on the mechanical properties of Ti6Al4V powder compacts prepared by magnetic pulse compaction

The effects of temperature （0-500°C） on the compressive strength,hardness,average relative density,and microstructure of Ti6Al4V powder green compacts prepared by magnetic pulse compaction were investigated.The results show that with increasing heating temperature,the compressive strength first increases and then decreases with the maximum value of 976.74 MPa at 400°C.The average relative density and hardness constantly increase,and their values reach 96.11% and HRA 69.8 at 500°C,respectively.The increase of partial welding is found among the junctions of particles inside the compacts; there is no obvious grain growth inside the compacts within the temperature range.

Temperature-dependent evolution of oxide inclusions during heat treatment of stainless steel with yttrium addition

The evolution of oxide inclusions during isothermal heating of 18Cr–8Ni stainless steel with yttrium addition at temperatures of 1273 to 1573 K was investigated systematically.Homogeneous spherical Al–Y–Si(–Mn–Cr)oxide inclusions were observed in as-cast steel.After heating,most of the homogeneous inclusions were transformed into heterogeneous inclusions with Y-rich and Al-rich parts,even though some homogeneous oxide particles were still observed at 1273 and 1573 K.With the increase in heating temperature,more large-sized inclusions were formed.The shape of the inclusions also changed from spherical to irregular.The maximum transformation temperature of inclusions was determined to be 1373 K.The evolution mechanism of inclusions during heating was proposed to be the combined effect of the(i)internal transformation of inclusions due to the crystallization of glassy oxide and(ii)interfacial reaction between inclusions and steel matrix.Meanwhile,the internal transformation of inclusions was considered to be the main factor at heating temperatures less than 1473 K.

Effects of heat treatment temperature on oxidation behavior of glass-like carbon derived from acetone-furfural resin

Glass-like carbons （GCs） were prepared by carbonization of acetone-furfural resin in nitrogen atmosphere at 850℃, followed by heat treatment over a range of 1 200-2 500℃in inert atmosphere. The effect of heat treatment temperature （HTT） on the oxidation behavior was investigated by dynamic and isothermal thermogravimetric analyses. The structure of GC was examined by X-ray diffractometry （XRD） and the morphologies of GC before and after oxidation were examined by scanning electron microscopy （SEM）. It is shown that the GC samples present peculiar oxidation behavior. The anti-oxidation behavior increases with increasing the HTT to 1 600 ℃, whereas decreases gradually thereafter. GC sample heat treated at 1 600℃ obtains relatively optimal anti-oxidation properties under this condition. During the oxidation, this material produces grid network matrix surface and numerous nodular residues on the surface, resulting in excellent resistance to the attack of oxygen atoms.

Synthesis of Large-scale Multistream Heat Exchanger Networks Based on Stream Pseudo Temperature

Effective temperature level of stream, namely stream pseudo temperature, is determined by its actual temperature and heat transfer temperature difference contribution value. Heat transfer temperature difference con-tribution value of a stream depends on its heat transfer film coefficient, cost per unit heat transfer area, actual tem-perature, and so on. In the determination of the suitable heat transfer temperature difference contribution values of the stream, the total annual cost of multistream heat exchanger network (MSHEN) is regarded as an objective func-tion, and genetic/simulated annealing algorithm (GA/SA) is adopted for optimizing the heat transfer temperature difference contribution values of the stream. The stream pseudo temperatures are subsequently obtained. On the ba-sis of stream pseudo temperature, optimized MSHEN can be attained by the temperature-enthalpy (T-H) diagram method. This approach is characterized with fewer decision variables and higher feasibility of solutions. The calcu-lation efficiency of GA/SA can be remarkably enhanced by this approach and more probability is shown in search-ing the global optimum solution. Hence this approach is presented for solving industrial-sized MSHEN which is difficult to deal by traditional algorithm. Moreover, in the optimization of stream heat transfer temperature differ-ence contribution values, the effects of the stream temperature, the heat transfer film coefficient, and the construc-tion material of heat exchangers are considered, therefore this approach can be used to optimize and design heat exchanger network (HEN) with unequal heat transfer film coefficients and different of construction materials. The performance of the proposed approach has been demonstrated with three examples and the obtained solutions are compared with those available in literatures. The results show that the large-scale MSHEN synthesis problems can be solved to obtain good solutions with the modest computational effort.

Effect of Heat Treatment Temperature on Properties of Chinese Calcined Flint Clay Based Plastic Refractories

Effects of different heat treatment temperatures on properties of Chinese calcined flint clay based plastic refractories were investigated using Chinese calcined flint clay as starting material, aluminum sulfate and fireclay as binding system. The results showed that with temperature rising, Chinese calcined flint clay based plastic refractories shrinked firstly and then expanded. The modulus of rupture （MOR） and the cold crushing strength （CCS） inereased firstly and then decreased from 110 ℃ to 600 ℃ , then increased obviously. Thermal expansion coefficient increased from 110 ℃ to 760 ℃, decreased from 760 ℃ to 1 300 ℃ , and increased from 1 300 ℃ to1500 ℃.

Application of high temperature heat pipe in hypersonic vehicles thermal protection

In order to develop further the application of high temperature heat pipe in hypersonic vehicles thermal protection, the principles and characteristics of high temperature heat pipe used in hypersonic vehicles thermal protection were introduced. The methods of numerical simulation, theory analysis and experiment research were utilized to analyze the frozen start-up and steady state characteristic of the heat pipe as well as the machining improvement for fabricating irregularly shaped heat pipe which is suitable for leading edge of hypersonic vehicles. The results indicate that the frozen start-up time of heat pipe is long （10 min） and there exists large temperature difference along the heat pipe （47 ℃/cm）, but the heat pipe can reduce the temperature in stagnation area of hypersonic vehicles from 1 926 to 982 ℃ and work normally during 1 000-1 200℃. How to improve the maximum heat transfer capability and reduce the time needed for start-up from frozen state of the heat pipe by optimizing thermostructure such as designing of a novel wick with high performance is the key point in hypersonic vehicles thermal protection of heat pipe.

Seasonal Variation of the East Asian Subtropical Westerly Jet and Its Association with the Heating Field over East Asia

The structure and seasonal variation of the East Asian Subtropical Westerly Jet （EAWJ） and associations with heating fields over East Asia are examined by using NCEP/NCAR reanalysis data. Obvious differences exist in the westerly jet intensity and location in different regions and seasons due to the ocean-land distribution and seasonal thermal contrast, as well as the dynamic and thermodynamic impacts of the Tibetan Plateau. In winter, the EAWJ center is situated over the western Pacific Ocean and the intensity is reduced gradually from east to west over the East Asian region. In summer, the EAWJ center is located over the north of the Tibetan Plateau and the jet intensity is reduced evidently compared with that in winter. The EAWJ seasonal evolution is characterized by the obvious longitudinal inconsistency of the northward migration and in-phase southward retreat of the EAWJ axis. A good correspondence between the seasonal variations of EAWJ and the meridional differences of air temperature （MDT） in the mid-upper troposphere demonstrates that the MDT is the basic reason for the seasonal variation of EAWJ. Correlation analyses indicate that the Kuroshio Current region to the south of Japan and the Tibetan Plateau are the key areas for the variations of the EAWJ intensities in winter and in summer, respectively. The strong sensible and latent heating in the Kuroshio Current region is closely related to the intensification of EAWJ in winter. In summer, strong sensible heating in the Tibetan Plateau corresponds to the EAWJ strengthening and southward shift, while the weak sensible heating in the Tibetan Plateau is consistent with the EAWJ weakening and northward migration.

Optimizing Low-Temperature Heat Recovery in a Refinery Fluid Catalytic Cracking Unit Based on Pinch Analysis

In this paper, the research was focused on optimizing low-temperature heat recovery to adopt multi-effect distil- lation （MED） in desalination by pinch technology. And further analysis indicated that phase changes occurred during the heat recovery process. In such case, the feed stream was divided into two streams： the liquid feed stream and the gaseous feed stream. Through calculation, the optimal ATmin was established at 26℃, and the total cost of heat exchange process was only $1.098× 106. By using the Problem Table Algorithm for pinch analysis, the temperature of the hot and the cold steams was 119℃ and 93 ℃, respectively. At a temperature higher than 119 ℃, all heat of the hot stream could not be cooled by the condenser, and the minimum heat load of utility （QH.min） was 440457.64 kW; and at a temperature below 93 ℃, all heat of the cold stream could not be provided by the heater, and the minimum cold load of utility （QC.min） was 1965993.85 kW. Finally, the synthesis of heat exchanger network was established through integrating two heat exchanger networks.

Experimental Performance of Moderate and High Temperature Heat Pump Charged with Refrigerant Mixture BY-3

Theoretical and experimental analysis of a new refrigerant mixture BY-3 was conducted based on a single-stage vapor compression refrigeration system. The water-water heat pump system used BY-3 to produce hot water when the low temperature was 20 ℃. The following results were obtained: the highest temperature at the condenser outlet reached about 85 ℃; when the difference between the water temperatures at the condenser outlet and the evaporator inlet was less than 40 ℃, the coefficient of performance (COP) was larger than 4; when the difference reached 55 ℃, the COP still kept 3; the discharge temperature of BY-3 was lower than 100 ℃, and the refrigerant vapor pressure kept lower than 1.8 MPa. When the water temperature at the condenser outlet reached over 85 ℃, nearly a 5 ℃ superheating temperature was maintained.

Maximum heat transfer capacity of high temperature heat pipe with triangular grooved wick

A mathematical model was developed to predict the maximum heat transfer capacity of high temperature heat pipe with triangular grooved wick. The effects of the inclination angle and geometry structure were considered in the proposed model.Maximum heat transfer capacity was also investigated experimentally. The model was validated by comparing with the experimental results. The maximum heat transfer capacity increases with the vapor core radius increasing. Compared with the inclination angle of0°, the maximum heat transfer capacity increases at the larger inclination angle, and the change with temperature is larger. The performance of heat pipe with triangular grooved wick is greatly influenced by gravity, so it is not recommended to be applied to the dish solar heat pipe receiver.

Low-temperature Rapid Synthesis of Ultrafine Hafnium Carbide Ceramic Powders

Nano hafnium carbide（HfC） powders were synthesized by sol-gel combining hightemperature rapid heat treatment process using citric acid and hafnium tetrachloride as the raw materials. The effects of ball milling treatment on the phase and morphology of pyrolysis products（HfO_2-C） and final HfC product were investigated and the influences of heat treatment temperature and holding time on the structure and properties of the synthesized hafnium carbide powders were also studied. The experimental results showed that the HfO_2-C powders with good uniformity and small particle size were prepared by controlling the milling time. Pure HfC powders with an average particle size of 500 nm were obtained at 1 700 ℃ with a holding time of 3 min, and the oxygen content was about 0.69 wt%, lower than that of the hafnium carbide powders prepared by SPS（0.97%）.

Interval finite difference method for steady-state temperature field prediction with interval parameters

A new numerical technique named interval finite difference method is proposed for the steady-state temperature field prediction with uncertainties in both physical parameters and boundary conditions. Interval variables are used to quantitatively describe the uncertain parameters with limited information. Based on different Taylor and Neumann series, two kinds of parameter perturbation methods are presented to approximately yield the ranges of the uncertain temperature field. By comparing the results with traditional Monte Carlo simulation, a numerical example is given to demonstrate the feasibility and effectiveness of the proposed method for solving steady-state heat conduction problem with uncertain-but-bounded parameters.

Physical, Psychological, and Social Health Impact of Temperature Rise Due to Urban Heat Island Phenomenon and Its Associated Factors

The Urban Heat Island Effect（UHI）has now become a commonly observed phenomenon worldwide.Indeed,it has become a significant environmental effect of urbanisation.In Malaysia,research results showed that UHI effects are very evident in several cities such as Kuala Lumpur and Putrajaya.UHI effect has long been observed to cause temperature of cities.

Feasibility Demonstrations of Liquid Turbine Power Generator Driven by Low Temperature Heats

Lower temperature waste heats less than 373 K have strong potentials to supply additional energies because of their enormous quantities and ubiquity. Accordingly, reinforcement of power generations harvesting low temperature heats is one of the urgent tasks for the current generation in order to accomplish energy sustainability in the coming decades. In this study, a liquid turbine power generator driven by lower temperature heats below 373 K was proposed in the aim of expanding selectable options for harvesting low temperature waste heats less than 373 K. The proposing system was so simply that it was mainly composed of a liquid turbine, a liquid container with a biphasic medium of water and an underlying water-insoluble low-boiling-point medium in a liquid phase, a heating section for vaporization of the liquid and a cooling section for entropy discharge outside the system. Assumed power generating steps via the proposing liquid turbine power generator were as follows: step 1: the underlying low-boiling-point medium in a liquid phase was vaporized, step 2: the surfacing vapor bubbles of low-boiling-point medium accompanied the biphasic medium in their wakes, step 3: such high momentum flux by step 2 rotated the liquid turbine (i.e. power generation), step 4: the surfacing low-boiling-point medium vapor was gradually condensed into droplets, step 5: the low-boiling-point medium droplets were submerged to the underlying medium in a liquid phase. Experiments with a prototype liquid turbine power generator proved power generations in accordance with the assumed steps at a little higher than ordinary temperature. Increasing output voltage could be obtained with an increase in the cooling temperature among tested ranging from 294 to 296 K in contrast to normal thermal engines. Further improvements of the direct current voltage from the proposing liquid turbine power generator can be expected by means of far more vigorous multiphase flow induced by adding solid powders and theoretical optimizations of heat and mass transfers.

Effect of aging temperature on the microstructures and mechanical properties of ZG12Cr9Mo1Co1NiVNbNB ferritic heat-resistant steel

The effect of aging on the mechanical properties and microstructures of a new ZG12Cr9 MolColNiVNbNB ferritic heat resistant steel was investigated in this work to satisfy the high steam parameters of the ultra-supercritical power plant.The results show that the main precipitates during aging are Fe（Cr,Mo）23C6,V（Nb）C,and（Fe2Mo） Laves in the steel.The amounts of the precipitated phases increase during aging,and correspondingly,the morphologies of phases are similar to be round.Fe（Cr,Mo）23C6 appears along boundaries and grows with increasing temperature.In addition,it is revealed that the martensitic laths are coarsened and eventually happen to be polygonization.The hardness and strength decrease gradually,whereas the plasticity of the steel increases.What＇s more,the hardness of this steel after creep is similar to that of other 9%-12%Cr ferritic steels.Thus,ZG12Cr9 MolColNiVNbNB can be used in the project.

Simulation of temperature field in pipe during single-face quenching process

Temperature-time curves were measured for the air cooling and laminar cooling of a steel plate.Convective heat transfer coefficients of steel plate and air as well as steel plate and laminar cooling water were computed inversely. Therefore,the temperature field in the single-face quenching process of a steel pipe was simulated using ABAQUS finite element softw are,and the relationships betw een the temperatures and quenching time at different positions of the steel pipe were obtained. In addition,the relationships betw een the cooling rates and quenching time,as w ell as betw een cooling rates and temperatures,were obtained. The simulation quickly produced accurate results,and it can be used to optimize the quenching process. In addition,the results provide a basis for rationally designing the composition of a single-face quenching steel pipe.

Effect of heat treatment temperature of the glaze lager on the structure and the formaldehyde removal performance of an interior wall tile

With the improvement of people’s living standards,a large number of petroleum products,daily necessities and decorations that can produce volatile organic compounds are used in decoration,which seriously affects the indoor air quality.Interior decoration materials have become a research hotspot in recent years.The purpose of this paper is to develop a kind of interior wall material with good indoor formaldehyde removal effect,easily using,and low cost.In this paper,combining different heat treatment temperatures of the glaze layer,tourmaline/diatomite-based interior wall tiles were prepared by ultrafine grinding,solid sintering,and low temperature calcination.The glaze layer under different heat treatment temperatures was characterized by thermogravimetric-differential thermal analysis,X-ray diffraction,and scanning electron microscope.The influences of heat treatment temperature on the microscopic morphology and structure of the glaze layer were analyzed.Taking formaldehyde as the target degradation product,the effects of tourmaline/diatomite-based interior wall tiles on the removal of formaldehyde under different heat treatment temperatures of the glaze layer were investigated.The results showed that with the increase in heat treatment temperature,the original pores of diatomite decreased,the specific surface area decreased,and the structure of tourmaline changed.At 850℃,the surface structure of the material was slightly damaged,the strength was increased,and the removal effect of formaldehyde was better.In a 1 m^(3) environmental chamber,the formaldehyde removal rate reached 73.6%in 300 min.When the temperature was increased to 950℃ and above,diatomite and the structure of tourmaline were destroyed,and the ability of the material to adsorb and degrade formaldehyde decreased.

Synthesis of SAPO-34/graphite composites for low temperature heat adsorption pumps

Low temperature heat adsorption pumps represent the innovative cooling systems, where cold is generated through adsorption/desorption cycle of water by a suitable adsorbent with good adsorption and high thermal conductive properties. In this work, the hydrothermal synthesis of zeolite SAPO-34 on thermal conductive grapbitic supports, aiming at the development of highly pertbrming adsorbent materials, is reported. The synthesis was carried out using as-received and oxidized commercial carbon papers, and graphite plate. Composites were characterized by XRD, SEM and also by a thermogravimetric method, using a Cahn microbalance. The water adsorbing capacity showed typical S-shape trend and the maximum water loading was around 25 wt%, a value close to water adsorption capability of pure SAPO-34. These results are very promising for their application in heat adsorption pumps.

Influence of Heat Treatment Temperature on Microstructure and Bonding of TiO2 Film Coated on Diamond Particles Surface

TiO_2 films were coated on the surface of diamond particles using a sol-gel method. The effects of heat treatment temperature on the morphology, phase composition and chemical bond of diamond particles coated with TiO2 films were investigated through SEM, TEM, X-ray diffraction analysis, Raman spectroscopy, FTIR, and XPS. The results showed that when being heat-treated at 600 ℃, the amorphous TiO_2 film transfered to the anatase film which bonded well with diamond substrate. Meanwhile, the Ti-O-C bond formed between TiO2 film and diamond substrate. When being heat-treated at 800 ℃, TiO2 film was still anatase, and partial diamond began to graphitize. The graphitizated carbon could also form the Ti-O-C bond with TiO_2 film, although TiO_2 film would tend to crack in this case.