Numerical Calculation of the Peaking Factor of a Water-Cooled W/Cu Monoblock for a Divertor

In order to accurately predict the incident critical heat flux（ICHF,the heat flux at the heated surface when CHF occurs） of a water-cooled W/Cu monoblock for a divertor,the exact knowledge of its peaking factors（f_p） under one-sided heating conditions with different design parameters is a key issue.In this paper,the heat conduction in the solid domain of a water-cooled W/Cu monoblock is calculated numerically by assuming the local heat transfer coefficients（HTC）of the cooling wall to be functions of the local wall temperature,so as to obtain f_p.The reliability of the calculation method is validated by an experimental example result,with the maximum error of 2.1% only.The effects of geometric and flow parameters on the f_p of a water-cooled W/Cu monoblock are investigated.Within the scope of this study,it is shown that the f_p increases with increasing dimensionless W/Cu monoblock width and armour thickness（the shortest distance between the heated surface and Cu layer）,and the maximum increases are 43.8% and 22.4% respectively.The dimensionless W/Cu monoblock height and Cu thickness have little effect on f_p.The increase of Reynolds number and Jakob number causes the increase of f_p,and the maximum increases are 6.8% and 9.6% respectively.Based on the calculated results,an empirical correlation on peaking factor is obtained via regression.These results provide a valuable reference for the thermal-hydraulic design of water-cooled divertors.

Hydration Heat Evolution of Cement and Its Relation With Setting Time

In order to veritably measure the first peak of hydration heat evolution that has been illustrated important in indicating cement behavior in early hydration, an improved way of water addition into cement in isothermally calorimetric experiment is put forward. The experimental results indicated that: the magnitude of first peak of heat evolution varies from sample to sample, correlation between heat evolution during first peak of heat evolution and initial (as well as final) setting time is unsatisfactory when samples are not classified; while groups of sample classified based on strength grade represent satisfactory correlations, which indicating the existence of close relation between hydration heat evolution in much earlier hydration age and setting property of cement in rather later age. Importance of first peak in hydration heat evolution for understanding cement setting property and reasons for sample classification are also discussed in this paper.

Simulation study on heat-affected zone of high-strain X80 pipeline steel

The microstructure evolution and impact-toughness variation of heat-affected zone（HAZ）in X80 highstrain pipeline steel were investigated via a welding thermal-simulation technique,Charpy impact tests,and scanning electron microscopy observations under different welding heat inputs and peak temperatures.The results indicate that when heat input was between 17 and 25kJ·cm^（-1）,the coarse-grained heat-affected zone showed improved impact toughness.When the heat input was increased further,the martensite-austenite（M-A）islands transformed from fine lath into a massive block.Therefore,impact toughness was substantially reduced.When the heat input was 20kJ·cm^（-1） and the peak temperature of the first thermal cycle was between 900 and 1300°C,a higher impact toughness was obtained.When heat input was 20kJ·cm^（-1） and the peak temperature of the first thermal cycle was 1300°C,the impact toughness value at the second peak temperature of 900°C was higher than that at the second peak temperature of 800°C because of grain refining and uniformly dispersed M-A constituents in the matrix of bainite.

Empirical investigation to explore potential gains from the amalgamation of phase changing materials(PCMs)and wood shavings

The reduction of gained heat,heat peak shifting,and the mitigation of air temperature fluctuations are some desirable properties that are sought after in any thermal insulation system.It cannot be overstated that these fac-tors,in addition to others,govern the performance of such systems thus their effect on indoor ambient conditions.The effect of such systems extends also to Heating,Ventilation and Air-conditioning(HVAC)systems that are set up to operate optimally in certain conditions.Where literature shows that PCMs and natural materials such as wood-shavings can provide efficient passive insulation for buildings,it is evident that such approaches utilise methods that are of a degree of intricacy which require specialist knowledge and complex techniques,such as micro-encapsulation for instance.With technical and economic aspects in mind,an amalgam of PCM and wood-shavings has been created to be utilised as a feasible thermal insulation.The amalgamation was performed in the simplest of methods,through submerging the wood shavings in PCM.An experimental procedure was devised to test the thermal performance of the amalgam and compare this to the performance of the same un-amalgamated materials.Comparative analysis revealed that no significant thermal gains would be expected from such amal-gamation.However,a significant reduction in the total weight of the insulation system would be achieved that,in this case,shown to be up to 20.94%.Thus,further reducing possible strains on structural elements due to the application of insulation on buildings.This can be especially beneficial in vernacular architectural approaches where considerably large amounts and thicknesses of insulations are used.In addition,cost reduction could be attained as wood shavings are significantly cheaper compared to the cost of PCMs.