Heavy oil has high density and viscosity, and exhibits viscoelasticity. Gassmann's theory is not suitable for materials saturated with viscoelastic fluids. Directly applying such model leads to unreliable results ...Heavy oil has high density and viscosity, and exhibits viscoelasticity. Gassmann's theory is not suitable for materials saturated with viscoelastic fluids. Directly applying such model leads to unreliable results for seismic inversion of heavy oil reservoir. To describe the viscoelastic behavior of heavy oil, we modeled the elastic properties of heavy oil with varying viscosity and frequency using the Cole-Cole-Maxwell (CCM) model. Then, we used a CCoherent Potential Approximation (CPA) instead of the Gassmann equations to account for the fluid effect, by extending the single-phase fluid condition to two-phase fluid (heavy oil and water) condition, so that partial saturation of heavy oil can be considered. This rock physics model establishes the relationship between the elastic modulus of reservoir rock and viscosity, frequency and saturation. The viscosity of the heavy oil and the elastic moduli and porosity of typical reservoir rock samples were measured in laboratory, which were used for calibration of the rock physics model. The well-calibrated frequency-variant CPA model was applied to the prediction of the P- and S-wave velocities in the seismic frequency range (1–100 Hz) and the inversion of petrophysical parameters for a heavy oil reservoir. The pre-stack inversion results of elastic parameters are improved compared with those results using the CPA model in the sonic logging frequency (∼10 kHz), or conventional rock physics model such as the Xu-Payne model. In addition, the inversion of the porosity of the reservoir was conducted with the simulated annealing method, and the result fits reasonably well with the logging curve and depicts the location of the heavy oil reservoir on the time slice. The application of the laboratory-calibrated CPA model provides better results with the velocity dispersion correction, suggesting the important role of accurate frequency dependent rock physics models in the seismic prediction of heavy oil reservoirs.展开更多
Freshwater microplastic pollution is an urgent issue of global concern,and research on the distribution in reservoirs is lacking.We investigated the microplastic pollution levels in wet sediments collected from the Th...Freshwater microplastic pollution is an urgent issue of global concern,and research on the distribution in reservoirs is lacking.We investigated the microplastic pollution levels in wet sediments collected from the Three Gorges Reservoir,the largest reservoir of China.Results show that microplastics were ubiquitous in the sediments of the Three Gorges Reservoir,and their abundance ranged from 59 to 276 pp/kg(plastic particles per kg,dry weight).Economic development and total population were important factors affecting the spatial heterogeneity of microplastic abundance,and the contribution of large cities along the reservoir to microplastic pollution should be paid with more attention.Fibrous microplastics were the most abundant type of microplastic particles in reservoir sediments,whereas polystyrene,polypropylene,and polyamide were the main types of polymers.The apparent spatial heterogeneity in morphology and color of microplastics is attributed to different anthropogenic or landbased pollution sources.Moreover,the accumulation of microplastics near the inlet of tributaries reflects the role of potential contributors of tributaries.More importantly,multiple bisphenols(BPs)and heavy metals detected at the microplastic surfaces indicate that microplastics can act as carriers of these pollutants in the environment in the same way as sediments did,which may alter the environmental fate and toxicity of these pollutants.Therefore,we conclude that the Three Gorges Reservoir had been contaminated with microplastics,which posed a stress risk for organisms who ingest them along with their associated pollutants(BPs,heavy metals).展开更多
The efficiency of water flooding in heavy oil reservoirs would be improved by increasing the viscosity of the displacing phase, but the sweep efficiency is not of significance due to the low mobility of the vicious oi...The efficiency of water flooding in heavy oil reservoirs would be improved by increasing the viscosity of the displacing phase, but the sweep efficiency is not of significance due to the low mobility of the vicious oil. On the basis of mobility control theory, increasing the residual resistance factor not only reduces the water-oil mobility ratio but also decreases the requirement for viscosity enhancement of the polymer solution. The residual resistance factor caused by hydrophobic associating polymer solution is higher than that caused by polyacrylamide solution in brine containing high concentrations of calcium and magnesium ions. The results of numerical simulations show that the polymer flooding efficiency improved by increasing the residual resistance factor is far better than that by only increasing solution viscosity. The recovery factor of heavy oil reservoirs (70 mPa·s) can be enhanced by hydrophobic associating polymer solution of high residual resistance factor (more than 3) and high effective viscosity (24 mPa·s). Therefore, increasing the residual resistance factor of the polymer solution not only decreases the requirement for the viscosity of polymer solution injected into heavy oil reservoirs but also is favorable to enhanced oil recovery during polymer flooding.展开更多
Polymer flooding has been proven to effectively improve oil recovery in the Bohai Oil Field. However, due to high oil viscosity and significant formation heterogeneity, it is necessary to further improve the displacem...Polymer flooding has been proven to effectively improve oil recovery in the Bohai Oil Field. However, due to high oil viscosity and significant formation heterogeneity, it is necessary to further improve the displacement effectiveness of polymer flooding in heavy oil reservoirs in the service life of offshore platforms. In this paper, the effects of the water/oil mobility ratio in heavy oil reservoirs and the dimensionless oil productivity index on polymer flooding effectiveness were studied utilizing rel- ative permeability curves. The results showed that when the water saturation was less than the value, where the water/oil mobility ratio was equal to 1, polymer flooding could effectively control the increase of fractional water flow, which meant that the upper limit of water/oil ratio suitable for polymer flooding should be the value when the water/oil mobility ratio was equal to 1. Mean while, by injecting a certain volume of water to create water channels in the reservoir, the polymer flooding would be the most effective in improving sweep efficiency, and lower the fractional flow of water to the value corresponding to △Jmax. Considering the service life of the platform and the polymer mobility control capacity, the best polymer injection timing for heavy oil reservoirs was optimized. It has been tested for reservoirs with crude oil viscosity of 123 and 70 mPa s, the optimum polymer flooding effec- tiveness could be obtained when the polymer floods were initiated at the time when the fractional flow of water were 10 % and 25 %, respectively. The injection timing range for polymer flooding was also theoretically analyzed for the Bohai Oil Field utilizing which provided methods for effectiveness. relative permeability curves, improving polymer flooding展开更多
The impact of reservoir emptying on the concentrations of dissolved heavy metals (As, Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn) in pore and surface waters was studied in the Aar Reservoir, a small reservoir in central German...The impact of reservoir emptying on the concentrations of dissolved heavy metals (As, Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn) in pore and surface waters was studied in the Aar Reservoir, a small reservoir in central Germany, during and after the emptying process. This study was conducted to observe binding changes within pore waters as well as the input of dissolved heavy metals in waters of the Aar Creek, what becomes possible when the reservoirs water table is removed and lake sediments become exposed. In pore waters, no clear shifting tendencies between dissolved and sorbed heavy metal fractions could be found after the completed sediment exposure. These relatively low dynamics in pore waters can be explained by the fine texture of the lake sediments, which are characterized by a high water holding capacity, what led to high remaining water contents and therefore slowed down the redox changes. A few days after the completed emptying, a general increase of dissolved heavy metal concentrations occurred in running waters of the Aar Creek as a result of pore water drainage. Here, element specific differences in mobilization and transportation abilities were found, what can be reconstructed by the ratio of dissolved heavy metals in pore and surface waters.展开更多
S oil field is a typical of water injection development of heavy oil reservoir in Bohai, and the formation of crude oil viscosity is 42 - 284 mPa?s. Due to the formation of crude oil viscosity, the oil field developme...S oil field is a typical of water injection development of heavy oil reservoir in Bohai, and the formation of crude oil viscosity is 42 - 284 mPa?s. Due to the formation of crude oil viscosity, the oil field development gradually faces a series of problems as rapid rise of water cut, rapid decline of output, high water cut of oil wells and others. In order to improve the effect of oilfield development, it is necessary to increase the output of the oilfield by adjusting wells for the potential in the oilfield. However, due to the high cost of drilling, operation and testing of offshore oilfields, offshore oilfields require more elaborate description of residual oil and adjustment wells. With the continuous downturn in international oil prices and the lack of new testing data in old oilfields, it is urgent to re-use the existing data in oilfields through innovative methods to achieve a detailed description of the remaining oil in the oilfields and improve the precision research of indexing wells and ensure the reliable implementation of adjustment wells. Based on the existing dynamic data of S oilfield, this paper proposes a new method to quantitatively evaluate water flooding coefficient by using tracer theory to establish tracer data, and quantitatively evaluates the vicinity of the fault by means of image reflection and potential superposition and find the residual oil in the imperfect area of the well network, combined with the numerical simulation method to realize the fine description of remaining oil and improve the research precision of the adjustment well. Through the research in this paper, S oilfield has proposed to location of six adjustment wells which has implemented two. The production confirmed that the method of this paper has some reliability, while the method of heavy oil in the high water cut stage of residual oil fine description. The research of enhanced oil recovery in the stage has certain guiding significance for heavy oil reservoirs.展开更多
Non-condensable gas(NCG),foam and surfactant are the three commonly-used additives in hybrid steam-chemical processes for heavy oil reservoirs.Their application can effectively control the steam injection profile and ...Non-condensable gas(NCG),foam and surfactant are the three commonly-used additives in hybrid steam-chemical processes for heavy oil reservoirs.Their application can effectively control the steam injection profile and increase the sweep efficiency.In this paper,the methods of microscale visualized experiment and macroscale 3D experiment are applied to systematically evaluate the areal and vertical sweep efficiencies of different hybrid steam-chemical processes.First,a series of static tests are performed to evaluate the effect of different additives on heavy oil properties.Then,by a series of tests on the microscale visualized model,the areal sweep efficiencies of a baseline steam flooding process and different follow-up hybrid EOR processes are obtained from the collected 2D images.Specifically,they include the hybrid steam-N_(2)process,hybrid steam-N2/foam process,hybrid steam-surfactant process and hybrid steam-N2/foam/surfactant process(N2/foam slug first and steam-surfactant co-injection then).From the results of static tests and visualized micromodels,the pore scale EOR mechanisms and the difference between them can be discussed.For the vertical sweep efficiencies,a macroscale 3D experiment of steam flooding process and a follow-up hybrid EOR process is conducted.Thereafter,combing the macroscale 3D experiment and laboratory-scaled numerical simulation,the vertical and overall sweep efficiencies of different hybrid steam-chemical processes are evaluated.Results indicate that compared with a steam flooding process,the areal sweep efficiency of a hybrid steam-N2process is lower.It is caused by the high mobility ratio in a steam-N2-heavy oil system.By contrast,the enhancement of sweep efficiency by a hybrid steam-N2/foam/surfactant process is the highest.It is because of the high resistance capacity of NCG foam system and the performance of surfactant.Specifically,a surfactant can interact with the oil film in chief zone and reduce the interfacial energy,and thus the oil droplets/films formed during steam injection stage are unlocked.For NCG foam,it can plug the chief steam flow zone and thus the subsequent injected steam is re-directed.Simultaneously,from the collected 2D images,it is also observed that the reservoir microscopic heterogeneity can have an important effect on their sweep efficiencies.From the 3D experiment and laboratory-scaled numerical simulation,it is found that a N2/foam slug can increase the thermal front angle by about 150 and increase the vertical sweep efficiency by about 26%.Among the four processes,a multiple hybrid EOR process(steam-N2/foam/surfactant process) is recommended than the other ones.This paper provides a novel method to systematically evaluate the sweep efficiency of hybrid steam-chemical process and some new insights on the mechanisms of sweep efficiency enhancement are also addressed.It can benefit the expansion of hybrid steam-chemical processes in the post steamed heavy oil reservoirs.展开更多
Surface soil/sediment samples were collected from the Water-Level Fluctuation Zone(WLFZ), cultivated land and forest land at 50 different grid points from Shenjia watershed, the Three Gorges Reservoir area in August 2...Surface soil/sediment samples were collected from the Water-Level Fluctuation Zone(WLFZ), cultivated land and forest land at 50 different grid points from Shenjia watershed, the Three Gorges Reservoir area in August 2013. The spatial distribution, sources and ecological risk assessment for Arsenic(As), Cadmium(Cd),Chromium(Cr), Copper(Cu), Nickel(Ni), Lead(Pb)and Zinc(Zn) were analyzed in this study. The results showed all tested metals had similar distribution patterns except Ni and Cr, with areas of high concentrations distributed in the southwest(WLFZ and watershed outlet) of the study area. Ni and Cr,which were highly positively correlated and present in high concentrations, were primarily distributed in the south and middle zones of the study area. Lower concentration areas of all metals were uniformly distributed west of the high-elevation zones and forest land. Factor analysis(FA) and factor analysismultiple linear regression(FA-MLR) showed that the major sources of Cd were fertilizer and traffic sources,which together accounted for 87% of Cd. As, Zn and Cu levels were primarily supplied by industrial and domestic sources, accounting for 76% of As, 75% of Cu and 67% of Zn. Surface soils/sediments of the study watershed contaminated by Cd represent a high ecological risk, whereas other metals represent low ecological risks. The potential ecological risk index(PERI) analysis indicated that it had a low(widerange) ecological risk and a moderate(small-range)ecological risk primarily distributed in the outlet of the study watershed. Fertilizers and traffic are the primary sources of Cd pollution, which should be more closely controlled for the purposes of water quality and ecological conservation.展开更多
Primary production mechanisms do not recover an appreciable fraction of the hydrocarbon initially in place (HIIP). Practical knowledge has shown that, at the point when the natural energy in a heavy oil reservoir is n...Primary production mechanisms do not recover an appreciable fraction of the hydrocarbon initially in place (HIIP). Practical knowledge has shown that, at the point when the natural energy in a heavy oil reservoir is nearly or altogether depleted, the recovery factor does not exceed about 20%. Some heavy oil reservoirs do not produce at all by natural drive mechanisms. This often necessitates adopting a production improvement strategy to augment recovery. Prior to implementing an improved oil recovery method (either secondary or tertiary) in the field, it is very important to investigate its potential for success. Reservoir simulation is a part of a continuous learning process used to gain insight into the feasibility and applicability of improved oil recovery methods. In this project, GEM compositional reservoir simulator has been used to study the efficiencies of different improved oil recovery strategies, ranging from waterflooding to solvent injection. The drainage volume investigated is a hypothetical box-shaped heavy oil reservoir composed of three distinct permeable layers.展开更多
Compared with conventional well, herringbone-like laterals wells can increase the area of oil release, and can reduce the number of wellhead slots of platforms,?and?also can greatly improve the development efficiency....Compared with conventional well, herringbone-like laterals wells can increase the area of oil release, and can reduce the number of wellhead slots of platforms,?and?also can greatly improve the development efficiency. Based on threshold pressure gradient in heavy oil reservoir,?and?the applied principle of mirror reflection and superposition, the pressure distribution equation of herringbone-like laterals wells is obtained in heavy oil reservoir. Productivity model of herringbone-like laterals wells is proposed by reservoir-wellbore steady seepage. The example shows that the productivity model is great accuracy?to?predict the productivity of herringbone-like laterals wells. The model is used to analyze the branching length, branching angle, branching symmetry, branching position and spacing and their effects on productivity of herringbone-like laterals wells. The principle of optimizing the well shape of herringbone-like laterals wells is proposed.展开更多
To improve the oil recovery and economic efficiency in heavy oil reservoirs in late steam flooding,taking J6 Block of Xinjiang Oilfield as the research object,3D physical modeling experiments of steam flooding,CO2-foa...To improve the oil recovery and economic efficiency in heavy oil reservoirs in late steam flooding,taking J6 Block of Xinjiang Oilfield as the research object,3D physical modeling experiments of steam flooding,CO2-foam assisted steam flooding,and CO2 assisted steam flooding under different perforation conditions are conducted,and CO2-assisted steam flooding is proposed for reservoirs in the late stage of steam flooding.The experimental results show that after adjusting the perforation in late steam flooding,the CO2 assisted steam flooding formed a lateral expansion of the steam chamber in the middle and lower parts of the injection well and a development mode for the production of overriding gravity oil drainage in the top chamber of the production well;high temperature water,oil,and CO2 formed stable low-viscosity quasi-single-phase emulsified fluid;and CO2 acted as a thermal insulation in the steam chamber at the top,reduced the steam partial pressure inside the steam chamber,and effectively improved the heat efficiency of injected steam.Based on the three-dimensional physical experiments and the developed situation of the J6 block in Xinjiang Oilfield,the CO2 assisted steam flooding for the J6 block was designed.The application showed that the CO2 assisted steam flooding made the oil vapor ratio increase from 0.12 to 0.16 by 34.0%,the oil recovery increase from 16.1%to 21.5%,and the final oil recovery goes up to 66.5%compared to steam flooding after perforation adjustment.展开更多
As a new method,the ultraviolet spectrum technique is applied to studying the connectivity of biodegradable heavy oil reservoirs.The similarity of crude oils can be judged according to the extinction coefficient(E) be...As a new method,the ultraviolet spectrum technique is applied to studying the connectivity of biodegradable heavy oil reservoirs.The similarity of crude oils can be judged according to the extinction coefficient(E) because aromatic hydrocarbons and non-hydrocarbons have conjugated bonds and obvious absorption in the ultraviolet range,and different materials have different characteristics and additives.The relationship diagram is made in terms of the extinction coefficients(E) of the samples by taking E as the Y-axis and wavelength as the X-axis.The connectivity of oil reservoirs is estimated according to the curve positions and characteristic fingerprints of the samples.The connectivity of part of the reservoirs in the western part of the QHD32-6 oilfield was studied with this method.The results showed that the connectivity of samples from wells F7 and F8 in the Nm-2 oil reservoir zone is good,that of samples from wells F17 and F20 in the Nm-1 oil reservoir zone also is good,and that of samples from wells F17,F19,and F20 is poor.展开更多
In order to optimize monitoring points and monitoring factor, the relationshipbetween pollutants and soil sample were established by correspondence analysis.Thestudy results show that the reflecting monitoring points ...In order to optimize monitoring points and monitoring factor, the relationshipbetween pollutants and soil sample were established by correspondence analysis.Thestudy results show that the reflecting monitoring points and monitoring factors in thegraphic on the same factor axis can clearly express the intrinsic link between pollutantsand monitoring points and distribution characteristics.To determine the main monitoringpoint and the main monitoring indicators can reduce and optimize the number of monitoringpoints under the premise of ensuring the typical and representative of monitoring data.Using the correlation of pollutants can reduce the number of monitoring indicators and improvethe effectiveness of data collection.展开更多
C oilfield is a heavy oil field developed by horizontal wells and single sand body in Bohai oilfield. The edge and bottom water of the reservoir is active and the natural energy development mode is adopted. The compre...C oilfield is a heavy oil field developed by horizontal wells and single sand body in Bohai oilfield. The edge and bottom water of the reservoir is active and the natural energy development mode is adopted. The comprehensive water cut of the oilfield was 95.3%, which had entered the stage of high water cut oil production. Some reservoirs were limited by crude oil viscosity and oil column height. Under the condition of existing development well pattern, some reserves were not produced or the degree of production was low, and the degree of well control was not high, so there is room for tapping the potential of remaining oil. This paper studied the rising law of water ridge of horizontal wells in bottom water reservoir by reservoir engineering method, and guided the infilling limit of horizontal wells in bottom water reservoir. At the same time, combined with the research results of fine reservoir description, the geological model was established, the numerical simulation was carried out, and the distribution law of remaining oil was analyzed. Through this study, we could understand the law of water flooding and remaining oil in the high water cut period of bottom water heavy oil reservoir, so as to provide guidance for the development strategy of this type of reservoir in the high water cut period.展开更多
基金supported by NSFC(41930425)Science Foundation of China University of Petroleum,Beijing(No.2462020YXZZ008)+1 种基金R&D Department of China National Petroleum Corporation(Investigations on fundamental experiments and advanced theoretical methods in geophysical prospecting applications(2022DQ0604-01)the Strategic Cooperation Technology Projects of CNPC and CUPB(ZLZX2020-03)and NSFC(42274142).
文摘Heavy oil has high density and viscosity, and exhibits viscoelasticity. Gassmann's theory is not suitable for materials saturated with viscoelastic fluids. Directly applying such model leads to unreliable results for seismic inversion of heavy oil reservoir. To describe the viscoelastic behavior of heavy oil, we modeled the elastic properties of heavy oil with varying viscosity and frequency using the Cole-Cole-Maxwell (CCM) model. Then, we used a CCoherent Potential Approximation (CPA) instead of the Gassmann equations to account for the fluid effect, by extending the single-phase fluid condition to two-phase fluid (heavy oil and water) condition, so that partial saturation of heavy oil can be considered. This rock physics model establishes the relationship between the elastic modulus of reservoir rock and viscosity, frequency and saturation. The viscosity of the heavy oil and the elastic moduli and porosity of typical reservoir rock samples were measured in laboratory, which were used for calibration of the rock physics model. The well-calibrated frequency-variant CPA model was applied to the prediction of the P- and S-wave velocities in the seismic frequency range (1–100 Hz) and the inversion of petrophysical parameters for a heavy oil reservoir. The pre-stack inversion results of elastic parameters are improved compared with those results using the CPA model in the sonic logging frequency (∼10 kHz), or conventional rock physics model such as the Xu-Payne model. In addition, the inversion of the porosity of the reservoir was conducted with the simulated annealing method, and the result fits reasonably well with the logging curve and depicts the location of the heavy oil reservoir on the time slice. The application of the laboratory-calibrated CPA model provides better results with the velocity dispersion correction, suggesting the important role of accurate frequency dependent rock physics models in the seismic prediction of heavy oil reservoirs.
基金the Natural Science Foundation of Chongqing,China(No.cstc2020jcyj-msxmX0763)。
文摘Freshwater microplastic pollution is an urgent issue of global concern,and research on the distribution in reservoirs is lacking.We investigated the microplastic pollution levels in wet sediments collected from the Three Gorges Reservoir,the largest reservoir of China.Results show that microplastics were ubiquitous in the sediments of the Three Gorges Reservoir,and their abundance ranged from 59 to 276 pp/kg(plastic particles per kg,dry weight).Economic development and total population were important factors affecting the spatial heterogeneity of microplastic abundance,and the contribution of large cities along the reservoir to microplastic pollution should be paid with more attention.Fibrous microplastics were the most abundant type of microplastic particles in reservoir sediments,whereas polystyrene,polypropylene,and polyamide were the main types of polymers.The apparent spatial heterogeneity in morphology and color of microplastics is attributed to different anthropogenic or landbased pollution sources.Moreover,the accumulation of microplastics near the inlet of tributaries reflects the role of potential contributors of tributaries.More importantly,multiple bisphenols(BPs)and heavy metals detected at the microplastic surfaces indicate that microplastics can act as carriers of these pollutants in the environment in the same way as sediments did,which may alter the environmental fate and toxicity of these pollutants.Therefore,we conclude that the Three Gorges Reservoir had been contaminated with microplastics,which posed a stress risk for organisms who ingest them along with their associated pollutants(BPs,heavy metals).
基金supported by the National High Technology Research and Development Program of China (863 Program: 2006AA09Z315 and 2007AA090701-3)
文摘The efficiency of water flooding in heavy oil reservoirs would be improved by increasing the viscosity of the displacing phase, but the sweep efficiency is not of significance due to the low mobility of the vicious oil. On the basis of mobility control theory, increasing the residual resistance factor not only reduces the water-oil mobility ratio but also decreases the requirement for viscosity enhancement of the polymer solution. The residual resistance factor caused by hydrophobic associating polymer solution is higher than that caused by polyacrylamide solution in brine containing high concentrations of calcium and magnesium ions. The results of numerical simulations show that the polymer flooding efficiency improved by increasing the residual resistance factor is far better than that by only increasing solution viscosity. The recovery factor of heavy oil reservoirs (70 mPa·s) can be enhanced by hydrophobic associating polymer solution of high residual resistance factor (more than 3) and high effective viscosity (24 mPa·s). Therefore, increasing the residual resistance factor of the polymer solution not only decreases the requirement for the viscosity of polymer solution injected into heavy oil reservoirs but also is favorable to enhanced oil recovery during polymer flooding.
基金supported by Open Fund (CRI2012RCPS0152CN) of State Key Laboratory of Offshore Oil Exploitationthe National Science and Technology Major Project (2011ZX05024-004-01)
文摘Polymer flooding has been proven to effectively improve oil recovery in the Bohai Oil Field. However, due to high oil viscosity and significant formation heterogeneity, it is necessary to further improve the displacement effectiveness of polymer flooding in heavy oil reservoirs in the service life of offshore platforms. In this paper, the effects of the water/oil mobility ratio in heavy oil reservoirs and the dimensionless oil productivity index on polymer flooding effectiveness were studied utilizing rel- ative permeability curves. The results showed that when the water saturation was less than the value, where the water/oil mobility ratio was equal to 1, polymer flooding could effectively control the increase of fractional water flow, which meant that the upper limit of water/oil ratio suitable for polymer flooding should be the value when the water/oil mobility ratio was equal to 1. Mean while, by injecting a certain volume of water to create water channels in the reservoir, the polymer flooding would be the most effective in improving sweep efficiency, and lower the fractional flow of water to the value corresponding to △Jmax. Considering the service life of the platform and the polymer mobility control capacity, the best polymer injection timing for heavy oil reservoirs was optimized. It has been tested for reservoirs with crude oil viscosity of 123 and 70 mPa s, the optimum polymer flooding effec- tiveness could be obtained when the polymer floods were initiated at the time when the fractional flow of water were 10 % and 25 %, respectively. The injection timing range for polymer flooding was also theoretically analyzed for the Bohai Oil Field utilizing which provided methods for effectiveness. relative permeability curves, improving polymer flooding
文摘The impact of reservoir emptying on the concentrations of dissolved heavy metals (As, Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn) in pore and surface waters was studied in the Aar Reservoir, a small reservoir in central Germany, during and after the emptying process. This study was conducted to observe binding changes within pore waters as well as the input of dissolved heavy metals in waters of the Aar Creek, what becomes possible when the reservoirs water table is removed and lake sediments become exposed. In pore waters, no clear shifting tendencies between dissolved and sorbed heavy metal fractions could be found after the completed sediment exposure. These relatively low dynamics in pore waters can be explained by the fine texture of the lake sediments, which are characterized by a high water holding capacity, what led to high remaining water contents and therefore slowed down the redox changes. A few days after the completed emptying, a general increase of dissolved heavy metal concentrations occurred in running waters of the Aar Creek as a result of pore water drainage. Here, element specific differences in mobilization and transportation abilities were found, what can be reconstructed by the ratio of dissolved heavy metals in pore and surface waters.
文摘S oil field is a typical of water injection development of heavy oil reservoir in Bohai, and the formation of crude oil viscosity is 42 - 284 mPa?s. Due to the formation of crude oil viscosity, the oil field development gradually faces a series of problems as rapid rise of water cut, rapid decline of output, high water cut of oil wells and others. In order to improve the effect of oilfield development, it is necessary to increase the output of the oilfield by adjusting wells for the potential in the oilfield. However, due to the high cost of drilling, operation and testing of offshore oilfields, offshore oilfields require more elaborate description of residual oil and adjustment wells. With the continuous downturn in international oil prices and the lack of new testing data in old oilfields, it is urgent to re-use the existing data in oilfields through innovative methods to achieve a detailed description of the remaining oil in the oilfields and improve the precision research of indexing wells and ensure the reliable implementation of adjustment wells. Based on the existing dynamic data of S oilfield, this paper proposes a new method to quantitatively evaluate water flooding coefficient by using tracer theory to establish tracer data, and quantitatively evaluates the vicinity of the fault by means of image reflection and potential superposition and find the residual oil in the imperfect area of the well network, combined with the numerical simulation method to realize the fine description of remaining oil and improve the research precision of the adjustment well. Through the research in this paper, S oilfield has proposed to location of six adjustment wells which has implemented two. The production confirmed that the method of this paper has some reliability, while the method of heavy oil in the high water cut stage of residual oil fine description. The research of enhanced oil recovery in the stage has certain guiding significance for heavy oil reservoirs.
基金financially supported by the National Natural Science Foundation of China(U20B6003,52004303)Beijing Natural Science Foundation(3212020)
文摘Non-condensable gas(NCG),foam and surfactant are the three commonly-used additives in hybrid steam-chemical processes for heavy oil reservoirs.Their application can effectively control the steam injection profile and increase the sweep efficiency.In this paper,the methods of microscale visualized experiment and macroscale 3D experiment are applied to systematically evaluate the areal and vertical sweep efficiencies of different hybrid steam-chemical processes.First,a series of static tests are performed to evaluate the effect of different additives on heavy oil properties.Then,by a series of tests on the microscale visualized model,the areal sweep efficiencies of a baseline steam flooding process and different follow-up hybrid EOR processes are obtained from the collected 2D images.Specifically,they include the hybrid steam-N_(2)process,hybrid steam-N2/foam process,hybrid steam-surfactant process and hybrid steam-N2/foam/surfactant process(N2/foam slug first and steam-surfactant co-injection then).From the results of static tests and visualized micromodels,the pore scale EOR mechanisms and the difference between them can be discussed.For the vertical sweep efficiencies,a macroscale 3D experiment of steam flooding process and a follow-up hybrid EOR process is conducted.Thereafter,combing the macroscale 3D experiment and laboratory-scaled numerical simulation,the vertical and overall sweep efficiencies of different hybrid steam-chemical processes are evaluated.Results indicate that compared with a steam flooding process,the areal sweep efficiency of a hybrid steam-N2process is lower.It is caused by the high mobility ratio in a steam-N2-heavy oil system.By contrast,the enhancement of sweep efficiency by a hybrid steam-N2/foam/surfactant process is the highest.It is because of the high resistance capacity of NCG foam system and the performance of surfactant.Specifically,a surfactant can interact with the oil film in chief zone and reduce the interfacial energy,and thus the oil droplets/films formed during steam injection stage are unlocked.For NCG foam,it can plug the chief steam flow zone and thus the subsequent injected steam is re-directed.Simultaneously,from the collected 2D images,it is also observed that the reservoir microscopic heterogeneity can have an important effect on their sweep efficiencies.From the 3D experiment and laboratory-scaled numerical simulation,it is found that a N2/foam slug can increase the thermal front angle by about 150 and increase the vertical sweep efficiency by about 26%.Among the four processes,a multiple hybrid EOR process(steam-N2/foam/surfactant process) is recommended than the other ones.This paper provides a novel method to systematically evaluate the sweep efficiency of hybrid steam-chemical process and some new insights on the mechanisms of sweep efficiency enhancement are also addressed.It can benefit the expansion of hybrid steam-chemical processes in the post steamed heavy oil reservoirs.
基金Financial support for this study was jointly provided by the National Natural Science Foundation of China(Grant No.41430750)National Key Basic Research Program of China(Grant Nos.2015CB452704,2016YFC0402301)the Chinese Academy of Sciences(Grant Nos.KFJ-EW-STS-008,KFJSW-STS-175)
文摘Surface soil/sediment samples were collected from the Water-Level Fluctuation Zone(WLFZ), cultivated land and forest land at 50 different grid points from Shenjia watershed, the Three Gorges Reservoir area in August 2013. The spatial distribution, sources and ecological risk assessment for Arsenic(As), Cadmium(Cd),Chromium(Cr), Copper(Cu), Nickel(Ni), Lead(Pb)and Zinc(Zn) were analyzed in this study. The results showed all tested metals had similar distribution patterns except Ni and Cr, with areas of high concentrations distributed in the southwest(WLFZ and watershed outlet) of the study area. Ni and Cr,which were highly positively correlated and present in high concentrations, were primarily distributed in the south and middle zones of the study area. Lower concentration areas of all metals were uniformly distributed west of the high-elevation zones and forest land. Factor analysis(FA) and factor analysismultiple linear regression(FA-MLR) showed that the major sources of Cd were fertilizer and traffic sources,which together accounted for 87% of Cd. As, Zn and Cu levels were primarily supplied by industrial and domestic sources, accounting for 76% of As, 75% of Cu and 67% of Zn. Surface soils/sediments of the study watershed contaminated by Cd represent a high ecological risk, whereas other metals represent low ecological risks. The potential ecological risk index(PERI) analysis indicated that it had a low(widerange) ecological risk and a moderate(small-range)ecological risk primarily distributed in the outlet of the study watershed. Fertilizers and traffic are the primary sources of Cd pollution, which should be more closely controlled for the purposes of water quality and ecological conservation.
文摘Primary production mechanisms do not recover an appreciable fraction of the hydrocarbon initially in place (HIIP). Practical knowledge has shown that, at the point when the natural energy in a heavy oil reservoir is nearly or altogether depleted, the recovery factor does not exceed about 20%. Some heavy oil reservoirs do not produce at all by natural drive mechanisms. This often necessitates adopting a production improvement strategy to augment recovery. Prior to implementing an improved oil recovery method (either secondary or tertiary) in the field, it is very important to investigate its potential for success. Reservoir simulation is a part of a continuous learning process used to gain insight into the feasibility and applicability of improved oil recovery methods. In this project, GEM compositional reservoir simulator has been used to study the efficiencies of different improved oil recovery strategies, ranging from waterflooding to solvent injection. The drainage volume investigated is a hypothetical box-shaped heavy oil reservoir composed of three distinct permeable layers.
文摘Compared with conventional well, herringbone-like laterals wells can increase the area of oil release, and can reduce the number of wellhead slots of platforms,?and?also can greatly improve the development efficiency. Based on threshold pressure gradient in heavy oil reservoir,?and?the applied principle of mirror reflection and superposition, the pressure distribution equation of herringbone-like laterals wells is obtained in heavy oil reservoir. Productivity model of herringbone-like laterals wells is proposed by reservoir-wellbore steady seepage. The example shows that the productivity model is great accuracy?to?predict the productivity of herringbone-like laterals wells. The model is used to analyze the branching length, branching angle, branching symmetry, branching position and spacing and their effects on productivity of herringbone-like laterals wells. The principle of optimizing the well shape of herringbone-like laterals wells is proposed.
基金Supported by the China National Science and Technology Major Project(2016ZX05012-002).
文摘To improve the oil recovery and economic efficiency in heavy oil reservoirs in late steam flooding,taking J6 Block of Xinjiang Oilfield as the research object,3D physical modeling experiments of steam flooding,CO2-foam assisted steam flooding,and CO2 assisted steam flooding under different perforation conditions are conducted,and CO2-assisted steam flooding is proposed for reservoirs in the late stage of steam flooding.The experimental results show that after adjusting the perforation in late steam flooding,the CO2 assisted steam flooding formed a lateral expansion of the steam chamber in the middle and lower parts of the injection well and a development mode for the production of overriding gravity oil drainage in the top chamber of the production well;high temperature water,oil,and CO2 formed stable low-viscosity quasi-single-phase emulsified fluid;and CO2 acted as a thermal insulation in the steam chamber at the top,reduced the steam partial pressure inside the steam chamber,and effectively improved the heat efficiency of injected steam.Based on the three-dimensional physical experiments and the developed situation of the J6 block in Xinjiang Oilfield,the CO2 assisted steam flooding for the J6 block was designed.The application showed that the CO2 assisted steam flooding made the oil vapor ratio increase from 0.12 to 0.16 by 34.0%,the oil recovery increase from 16.1%to 21.5%,and the final oil recovery goes up to 66.5%compared to steam flooding after perforation adjustment.
文摘As a new method,the ultraviolet spectrum technique is applied to studying the connectivity of biodegradable heavy oil reservoirs.The similarity of crude oils can be judged according to the extinction coefficient(E) because aromatic hydrocarbons and non-hydrocarbons have conjugated bonds and obvious absorption in the ultraviolet range,and different materials have different characteristics and additives.The relationship diagram is made in terms of the extinction coefficients(E) of the samples by taking E as the Y-axis and wavelength as the X-axis.The connectivity of oil reservoirs is estimated according to the curve positions and characteristic fingerprints of the samples.The connectivity of part of the reservoirs in the western part of the QHD32-6 oilfield was studied with this method.The results showed that the connectivity of samples from wells F7 and F8 in the Nm-2 oil reservoir zone is good,that of samples from wells F17 and F20 in the Nm-1 oil reservoir zone also is good,and that of samples from wells F17,F19,and F20 is poor.
基金Supported by the Public Welfare Research Program of State Environmental Protection Administration(200909065)
文摘In order to optimize monitoring points and monitoring factor, the relationshipbetween pollutants and soil sample were established by correspondence analysis.Thestudy results show that the reflecting monitoring points and monitoring factors in thegraphic on the same factor axis can clearly express the intrinsic link between pollutantsand monitoring points and distribution characteristics.To determine the main monitoringpoint and the main monitoring indicators can reduce and optimize the number of monitoringpoints under the premise of ensuring the typical and representative of monitoring data.Using the correlation of pollutants can reduce the number of monitoring indicators and improvethe effectiveness of data collection.
文摘C oilfield is a heavy oil field developed by horizontal wells and single sand body in Bohai oilfield. The edge and bottom water of the reservoir is active and the natural energy development mode is adopted. The comprehensive water cut of the oilfield was 95.3%, which had entered the stage of high water cut oil production. Some reservoirs were limited by crude oil viscosity and oil column height. Under the condition of existing development well pattern, some reserves were not produced or the degree of production was low, and the degree of well control was not high, so there is room for tapping the potential of remaining oil. This paper studied the rising law of water ridge of horizontal wells in bottom water reservoir by reservoir engineering method, and guided the infilling limit of horizontal wells in bottom water reservoir. At the same time, combined with the research results of fine reservoir description, the geological model was established, the numerical simulation was carried out, and the distribution law of remaining oil was analyzed. Through this study, we could understand the law of water flooding and remaining oil in the high water cut period of bottom water heavy oil reservoir, so as to provide guidance for the development strategy of this type of reservoir in the high water cut period.