Evaluation of the Oxidation Reactivity and Behavior of Exhaust Soot Particles from Diesel Engines with Different Emission Levels

The aim of this study was to investigate the oxidation reactivity and behavior of exhaust particulate matter(PM)from diesel engines.PM samples from two diesel engines(1K,CY4102)with different emission levels were collected by a thermophoretic system and a quartz filter.The oxidation reactivity,oxidation behaviors,and physicochemical properties of the PM samples were analyzed using thermogravimetric analysis(TGA),high-resolution transmission electron microscopy(HRTEM),Fourier-transform infrared spectrometry(FTIR),and Raman spectroscopy.The results showed that there was a great difference in the oxidation reactivity of soot particles emitted by the two different diesel engines.A qualitative analysis of the factors influencing oxidation reactivity showed that the nanostructure,degree of graphitization,and relative concentration of aliphatic C—H functional groups were the most important factors,whereas no significant correlation was found between the primary particle size and activation energy of the diesel soot.Based on the oxidation behavior analysis,the diesel soot particles exhibited both internal and surface oxidation modes during the oxidation process.Surface oxidation was dominant during the initial stage,and as oxidation progressed,the mode gradually changed to internal oxidation.Internal oxidation mode of soot particles from the 1K engine was significantly higher than that of CY4102.

Performance, Combustion and Emission Characteristics of Oxygenated Diesel in DI Engines: A Critical Review

The transition from non-renewable to renewable energy sources is a significant challenge of our time. In the fuel industry, oxygenated additives such as butanol are transforming conventional fuels into renewable biofuels. This technology has been utilized in reciprocating engines for decades. This paper reviews the viability of using an n-butanol blend as a short-term replacement for diesel by analyzing its physical and chemical properties, combustion, performance, and emission characteristics in compression ignition (CI) engines under various conditions, including variable load, speed, acceleration, and both stationary and transient cycles. N-Butanol exhibits higher viscosity, better lubricity, higher heating value, improved blend stability, enhanced cold-flow properties, and higher density. These factors influence spray formation, injection timing, atomization, and combustion characteristics. Its higher oxygen content improves the diffusion combustion stage and efficiency. Adding 5% and 10% n-butanol to diesel increases pressure and apparent heat release rate, slightly reduces temperature, and improves thermal efficiency, with mixed effects on CO and THC emissions and a notable decrease in particulate matter emissions. Fuel consumption increases, while the impact on NOx emissions varies. A 10% butanol blend is considered optimal for enhancing performance and reducing particulate emissions without significantly affecting NOx emissions. Blending up to 40% butanol with diesel does not require engine modifications or ECU recalibrations in engines calibrated for pure diesel. Due to its advantageous properties and performance, n-butanol is recommended as a superior alcohol-diesel blend than ethanol for short-term diesel replacement.

Combination of biodiesel-ethanol-diesel fuel blend and SCR catalyst assembly to reduce emissions from a heavy-duty diesel engine

In this study, the efforts to reduce NOx and particulate matter （PM） emissions from a diesel engine using both ethanol-selective catalytic reduction （SCR） of NOx over an Ag/Al2O3 catalyst and a biodiesel-ethanol-diesel fuel blend （BE-diesel） on an engine bench test are discussed. Compared with diesel fuel, use of BE-diesel increased PM emissions by 14% due to the increase in the soluble organic fraction （SOF） of PM, but it greatly reduced the Bosch smoke number by 60%-80% according to the results from 13-mode test of European Stationary Cycle （ESC） test. The SCR catalyst was effective in NOx reduction by ethanol, and the NOx conversion was approximately 73%. Total hydrocarbons （THC） and CO emissions increased significantly during the SCR of NOx process. Two diesel oxidation catalyst （DOC） assemblies were used after Ag/Al2O3 converter to remove CO and HC. Different oxidation catalyst showed opposite effect on PM emission. The PM composition analysis revealed that the net effect of oxidation catalyst on total PM was an integrative effect on SOF reduction and sulfate formation of PM. The engine bench test results indicated that the combination of BE-diesel and a SCR catalyst assembly could provide benefits for NOx and PM emissions control even without using diesel particle filters （DPFs）.

Optimization of the Performance of Marine Diesel Engines to Minimize the Formation of SO_x Emissions

Optimization procedures are required to minimize the amount of fuel consumption and exhaust emissions from marine engines.This study discusses the procedures to optimize the performance of any marine engine implemented in a 0D/1D numerical model in order to achieve lower values of exhaust emissions.From that point,an extension of previous simulation researches is presented to calculate the amount of SOx emissions from two marine diesel engines along their load diagrams based on the percentage of sulfur in the marine fuel used.The variations of SOx emissions are computed in g/k W·h and in parts per million(ppm)as functions of the optimized parameters:brake specific fuel consumption and the amount of air-fuel ratio respectively.Then,a surrogate model-based response surface methodology is used to generate polynomial equations to estimate the amount of SOx emissions as functions of engine speed and load.These developed non-dimensional equations can be further used directly to assess the value of SOx emissions for different percentages of sulfur of the selected or similar engines to be used in different marine applications.

HC-PM COUPLING MODEL FOR PARTICULATE MATTER EMISSION OF DIESEL ENGINES

A rapid, phenomenological model that predicts paniculate matter (PM) emissionof diesel engines is developed and formulated. The model is a chemical equilibrium compositionmodel, and is based on the formation mechanisms of PM and unburned hydrocarbon (HC) emissions ofdiesel engines. It can evaluate the emission concentration of PM via the emission concentration ofHC. To validate the model, experiments are carried out in two research diesel engines. Comparisonsof the model results with the experimental data show good agreement. The model can be used toevaluate the concentration of PM emission of diesel engines under lack of PM measuring instruments.In addition, the model is useful for computer simulations of diesel engines, as well as electroniccontrol unit (ECU) designs for electronically controlled diesel engines.

Hardware-in-the-Loop Research on the Electronic Control Unit for Diesel Engines

A hardware-in-the-loop simulating platform is developed to avoid designing defects caused by the complicated logical structure and multiple-functional buildup of the dectronic control unit（ECU）in modem diesel engines, and to diminish potential damages on components or human exposure to dangers in R＆D en- deavor. This plat-form consists of a computer installed with software Matlab/Simulink/RTW and dSPACE/ ControlDesk; a diesel engine ECU, and a dSPACE autobox which runs a real-time diesel engine model. A typical model of diesel engine with turbocharger and intercooler is presented. Based on this model our research is carried out with a real ECU to test its software control strategies. Results show that by using the diesel engine model downloaded inside, the hardware-in-the-loop platform can simulate diesel engine＇s working conditions and generate all kinds of sensor signals which ECU needs on a real-time basis. So the ECU control strategies can be validated and relevant parameters roughly calibrated.

Optimal Mixture Ratios of Biodiesel Ethanol Diesel for Diesel Engines

In this paper, we study the best-mixture ratio of biodiesel-ethanol-diesel for diesel engines. The simulation results show that the integrated indexes including engine power, cost-effectiveness and emission properties are rather better with different optimizing index when the ratio of bio-diesel, ethanol and diesel are 71.58:2.72:25.70 and 50:2.4127:47.5873.

Design and optimization of exhaust gas aftertreatment system for a heavy-duty diesel engine

Diesel engines meeting the latest emission regulations must be equipped with exhaust gas aftertreatment system,including diesel oxidation catalysts(DOC),diesel particulate filters(DPF),and selective catalytic reduction(SCR).However,before the final integration of the aftertreatment system(DOC+DPF+SCR)and the diesel engine,a reasonable structural optimization of the catalytic converters and a large number of bench calibration tests must be completed,involving large costs and long development cycles.The design and optimization of the exhaust gas aftertreatment system for a heavy-duty diesel engine was proposed in this paper.Firstly,one-dimensional(1D)and threedimensional(3D)computational models of the exhaust gas aftertreatment system accounting for the structural parameters of the catalytic converters were established.Then based on the calibrated models,the effects of the converter’s structural parameters on their main performance indicators,including the conversion of various exhaust pollutants and the temperatures and pressure drops of the converters,were studied.Finally,the optimal design scheme was obtained.The temperature distribution of the solid substrates and pressure distributions of the catalytic converters were studied based on the 3D model.The method proposed in this paper has guiding significance for the optimization of diesel engine aftertreatment systems.

Optimizing the Exhaust System of Marine Diesel Engines to Improve Low-speed Performances and Cylinder Working Conditions

Proper design of exhaust systems in marine high-power turbocharged diesel engines can contribute to improve the low-speed performance of these engines and make the working conditions of the cylinders more uniform.Here a high-power marine 16-cylinder V-type turbocharged diesel engine is simulated using the GT-Power software.The results reveal the differences induced by different exhaust system structures,such as an 8-cylinder-inpipe exhaust system with single/double superchargers and a 4-cylinder-in-pipe exhaust system with a single supercharger.After a comparative analysis,the 8-cylinder type with double superchargers is determined to be the optimal solution,and the structure of the exhaust system is further optimized.The simulations show that the optimized maximum exhaust temperature difference among cylinders is reduced by 66%.Finally,the simulation results and the optimized performance of the designed exhaust system are verified through experiments.

Miller Cycle with Early Intake Valve Closing in Marine Medium-Speed Diesel Engines

In this study,a one-dimensional simulation was performed to evaluate the performance of in-cylinder combustion to control NO_(x) emissions on a four-stroke,six-cylinder marine medium-speed diesel engine.Reducing the combustion temperature is an important in-cylinder measure to decrease NO_(x) emissions of marine diesel engines.The Miller cycle is an effective method used to reduce the maximum combustion temperature in a cylinder and accordingly decrease NO_(x) emissions.Therefore,the authors of this study designed seven different early intake valve closing(EIVC)Miller cycles for the original engine,and analyzed the cycle effects on combustions and emissions in high-load conditions.The results indicate that the temperature in the cylinder was significantly reduced,whereas fuel consumption was almost unchanged.When the IVC was properly advanced,the ignition delay period increased and the premixed combustion accelerated,but the in-cylinder average pressure,temperature and NO_(x) emissions in the cylinder were lower than the original engine.However,closing the intake valve too early led to high fuel consumption.In addition,the NO_(x) emissions,in-cylinder temperature,and heat release rate remarkably increased.Therefore,the optimal timing of the EIVC varied with different loads.The higher the load was,the earlier the best advance angle appeared.Therefore,the Miller cycle is an effective method for in-engine NO_(x) purification and does not entail significant cost.

Assessment of the Application of Subcooled Fluid Boiling to Diesel Engines for Heat Transfer Enhancement

The increasing demand of cooling in internal combustion engines(ICE)due to engine downsizing may require a shift in the heat removal method from the traditional single phase liquid convection to the application of new technologies based on subcooled fluid boiling.Accordingly,in the present study,experiments based on subcooled flow boiling of 50/50 by volume mixture of ethylene glycol and water coolant(EG/W)in a rectangular channel heated by a cast iron block are presented.Different degrees of subcooling,velocity and pressure conditions are examined.Comparison of three empirical reference models shows that noticeable deviations occur especially when low bulk subcooling and velocity conditions are considered.On the basis of the experimental data,a modified power-type wall heat flux model is developed and its ability to represent adequately reality is tested through numerical simulations against a reference rig case and a practical diesel engine.Computational results show that this modified model can effectively be used for practical engine cooling system design.

Experimental and Numerical Study of Impact of Air Filter Holes Masking on Altitude at Heavy-Duty Diesel Engine

At high altitudes, power of an internal combustion engine reduces due to air density reduction. In turbocharged diesel engine this issue affects the performance of the compressor and can result in unstable operation of the turbocharger if the power is not decreased by engine actuator. Mainly for testing the effects of altitude in the test room, air throttle valve and combustion air handling unit were used to reduce the suction air pressure. Easier and cheaper solution to consider effect of altitude on engine performance is to mask part of the air filter to reduce the suction pressure. In this paper, pressure drop against 0%, 26%, 52%, 66% and 74% of air filter hole’s masking for different mass flow rates has been studied by computational fluid dynamics. The analysis output mass flow rate-pressure diagram for the air filter, will be used as input data in the GT-Power software which is a one-dimensional computational fluid dynamics software and the effect of masking on altitude and performance at different revolutions per minute of the engine is investigated. Also, an experimental and computational fluid dynamics study was carried out to predict altitude against different proportions of air filter hole’s masking at 1000 rpm. The predicted results are validated by comparing with those of experimental data. A good agreement between the predicted and experimental values ensures the accuracy of the numerical predictions with the present work.

A New Method for Computing Radiation Heat Flow of In-Cylinder Soot of Diesel Engines

A concise formula for computing radiation heat flow of in-cylinder soot is presented, based on the assumptions that in-cylinder heat transfer of diesel engines is a quasi-equilibrium process and in-cylinder soot particles are spherical. That in this formula there consist neither constants needing adjustments nor variables related to engine types or operating conditions makes it universal and easy to use. Also it can be seen from the formula that radiation heat transfer is proportional to the quotient of in-cylinder soot mass over the average radius of primary particles. Besides, with the help of different algorithms it can be used for predicting cylinders＇ global as well as local radiation heat flows. As a demonstrative application on its global facet, a three-dimension simulation study about the soot-radiation-related heat flow in the combustion chamber of a diesel engine is carried out. Results show that the range of the soot-radiation-related heat flow computed by this formula agrees well with other researcher＇s earlier theoretic reasoning and experimental measurements.

A Review and Comparison on Recent Optimization Methodologies for Diesel Engines and Diesel Power Generators

The electrical instability that frequently distinguishes the isolated networks and depends on diesel generators to supply their energy requirements leads to an operation of the diesel generator in a transient dynamic condition and/or at low loads. In addition, extended operation of the diesel generator at partial load develops the condensation of combustion residues on the engine cylinder walls, which, after a certain time, increases friction, reduces the efficiency of the equipment and increases its fuel consumption. On the other hand, recent regulatory changes have led to ever more stringent and evolving emission standards. Among these, the International Maritime Organization (IMO) and the Environmental Protection Agency (EPA) have implemented emission standards in order to reduce exhaust gas emitted by marine diesel engines. To phase lower emission engines as soon as possible, a Tier system was adopted. This paper presents a literature review of existing technologies available to optimize the energy performance of diesel engines and diesel generators in order to reduce the cost of electricity, to increase the diesel engine efficiency and to decrease their fuel consumption and greenhouse gases (GHG) emissions. The proposed optimization methodologies are based on the application of Pre-treatment, Internal treatment and Post-treatment technologies for diesel engines and on the application of mechanical and electrical technologies for diesel power generators (DPGs). The list of references given at the end of the paper should offer aids for students and researchers working in this field.

An Evaluation of Human Error Probabilities for Critical Failures in Auxiliary Systems of Marine Diesel Engines

Human error,an important factor,may lead to serious results in various operational fields.The human factor plays a critical role in the risks and hazards of the maritime industry.A ship can achieve safe navigation when all operations in the engine room are conducted vigilantly.This paper presents a systematic evaluation of 20 failures in auxiliary systems of marine diesel engines that may be caused by human error.The Cognitive Reliability Error Analysis Method(CREAM)is used to determine the potentiality of human errors in the failures implied thanks to the answers of experts.Using this method,the probabilities of human error on failures were evaluated and the critical ones were emphasized.The measures to be taken for these results will make significant contributions not only to the seafarers but also to the ship owners.

Evaluation of properties for lubricant filter in diesel engines

The properties of lubricant filters in diesel engines directly affect operation of the lubricant system, and lubricant filters are apt to be impacted by many factors. Therefore, scientific and sensible methods evaluating the properties for lubricant filter diesel engines are necessary to monitor filter properties on line and dynamically. This paper applies ferrographic techniques and adopts sampling methods that oil specimens are synchronously obtained in front of and behind filter elements to monitor the filters of ISUZU DA-220 diesel engine in two FD50 forklifts. Results show that the combination of ferrographic techniques and above sampling methods is effective in analyzing the whole operating process of filters used in diesel engines. The service life and ruined type of filter can be estimated through the relationship between ferrographic readings in front and behind of filter and operation time. Furthermore, through a great deal of tests, a series of experimental curves of readings and time and characteristic parameters for filters used in different machines can be gained, which has guiding significance to the selection and maintenance of the filters. But because of the limitation of the ferrographic technique, the debris on the substrate prevents determination of sizes. It is difficult to judge accurately the size of debris that a filter can filter.

Dynamic Characteristic Investigation on the Fuel Pressure of Diesel Engines Electronic In-line Pump System

The electronic in-line pump (EIP) is a complex system consisting of mechanical, hydraulic, and electromagnetic parts. Experimental study showed that the fuel pressure of the plunger and the fuel drainage of the pressure system after fuel injection could result in fuel pressure fluctuation in the low pressure system. Such fluctuation exhibited pulsating cycle fluctuation as the amplitude rose with the increase of the injection pulse width. The time domain analysis found that the pressure time history curve and injection cylinders corresponded with a one-to-one relationship. By frequency domain analysis, the result was that with the increase of the working cylinder number, the high frequency amplitude gradually increased and the basic frequency amplitude gradually decreased. The conclusion was that through wavelet transformation, the low pressure signal simultaneously moved towards low frequency as the high frequency of the wavelet transformation signal with the working cylinder number increased. Lastly, by using the numerical model, the study investigated the simulation research concerning the relationship of the fluctuation dynamic characteristic in the low pressure system and the fuel injection characteristic of the high pressure system, completing the conclusions obtained by the experimental study.

Detection of cylinder pressure in diesel engines using cylinder head vibration and time series methods

This paper investigates the vibration characteristics of diesel engine cylinder heads by means of the time series method. With the concept of "Assumed System",the vibration transfer function of real cylinder head structures is established using the autoregressive-moving average models(ARMA models) of cylinder head surface vibration signals. Then this transfer function is successfully used to reconstruct the gas pressure trace inside the cylinder from measured cylinder head vibration signals. This offers an effective means for diesel engine cylinder pressure detection and condition monitoring.

Oxidization resistance of Ni76Cr19AlTi valve alloy at temperatures under operating mode of heavy-duty engines

The oxidization resistance of the Ni76Cr19A1Ti alloy was studied by a static oxidization experiment at 600-800℃. The results show that the oxidation behavior of the alloy can be explained by a kinetic equation： （△m/S）2 = Kpt ＋ C, where Kp is a kinetic constant of the nickel-base alloy. The higher the experimental temperature, the higher the value of Kp. It is discovered that the microstructure of the oxide scales is compact and the thickness of it is less than 10 μm The oxidization of the alloy is in the first grade. It is also found that the oxide scales are mainly composed of Cr2O3 and TiO2. Chrome and titanium react more easily with oxygen at temperatures under the operating mode.

Research on Fault Prediction for Marine Diesel Engines

Condition-based maintenance based on fault prediction has been widely concerned by the industry. Most of the contributions on fault prediction are based on various sensor data and mathematical models of the equipment. The complexity of the model and data signal is the key factor affecting the practicability of the model. In addition, even for the same type and batch of equipment, the manufacturing process, operation environment and other factors also affect the model parameters. In this paper, a series event model is conducted to predict the fault of marine diesel engines. Numerical example illustrates that the proposed event model is feasible.