Microstructure of the deepest zone of high speed steel W6Mo5Cr4V2(M2)melt after laser fu-sion was found to be so fine as the ehill zone of a solidified ingot.When narrower chill zoneformed,the long columnar dendrites ...Microstructure of the deepest zone of high speed steel W6Mo5Cr4V2(M2)melt after laser fu-sion was found to be so fine as the ehill zone of a solidified ingot.When narrower chill zoneformed,the long columnar dendrites grow into the melt and then the fine equiaxed cellularstructure appears in upper melt region nearly surface.The substructure of cellular grains anddendrites was observed to consist of martensite and retained austenile,while the carbides asM_6C_■ Cr_7C_3 and MC distributed at their boundaries.It is believed that the highermicrohardness up to HV_(0.1)=865-960 of the laser fused structure of the alloy is due to the oc-currence of martensite.展开更多
The NiAl-28Cr-5.85Mo-0.15Hf alloy was prepared by high-pressure die casting (HPDC) and subsequent hot isostatic pressing(HIP), and tested for compressible strength and fracture behavior at 300-1 373 K. The results sho...The NiAl-28Cr-5.85Mo-0.15Hf alloy was prepared by high-pressure die casting (HPDC) and subsequent hot isostatic pressing(HIP), and tested for compressible strength and fracture behavior at 300-1 373 K. The results show that the elevated temperature 0.2% compressible yield strength as well as the room-temperature compressible fracture strain of as-HIP alloy are larger than those of the same alloy prepared by directional solidification (DS). It suggests that the fine structures with a homogeneous distribution of fine Cr (Mo) and Hf-rich phase created by high-pressure die casting lead to these improvements.展开更多
A novel trench MOS barrier Schottky diode（TMBS） device with a high-k material introduced into the gate insulator is reported, which is named high-k TMBS. By simulation with Medici, it is found that the high-k TMBS c...A novel trench MOS barrier Schottky diode（TMBS） device with a high-k material introduced into the gate insulator is reported, which is named high-k TMBS. By simulation with Medici, it is found that the high-k TMBS can have 19.8% lower leakage current while maintaining the same breakdown voltage and forward turn-on voltage compared with the conventional regular trench TMBS.展开更多
The catalysts were prepared by the temperature programmed reaction (TPR) of MoO3 with NH3 at various temperatures in the range of 573K～973K, and their hydrodenitrogenation (HDN) activities were tested in situ.It is s...The catalysts were prepared by the temperature programmed reaction (TPR) of MoO3 with NH3 at various temperatures in the range of 573K～973K, and their hydrodenitrogenation (HDN) activities were tested in situ.It is shown that molybdenum nitrid(Mo2N) was formed above 923K and its intermediate MoO2 formed at about 573～623K under the rapid (5K/min.) TPR conditions.Mo2N is the most active species for pyridine HDN among MoO3,MoO2,MoS2,and Mo2N. Moreover,it can be promoted by adding Ni component.It is shown that the Ni/Mo2N catalyst prepared by adding some NiO into the precursor MoO3 has a steady HDN activity Which is far higher than that of the commercial sulfided NiMo/Al2O3(HR346) catalyst.展开更多
High density lipoprotein binding protein （HBP） plays an important role in lipid metabolism of animals. Lipids are indispensable energy materials for fi- shes, especially for carnivorous fishes with low utilization e...High density lipoprotein binding protein （HBP） plays an important role in lipid metabolism of animals. Lipids are indispensable energy materials for fi- shes, especially for carnivorous fishes with low utilization efficiency of carbohydrates. The single nucleotide polymorphism （SNP） of HBP gene may affect the fat metabolism, thereby exerting an effect on the growth traits of largemouth bass （Micropterus salmoides）. Investigating the correlations between SNP and growth traits can provide candidate markers for molecular marker-assisted selection. In this study, partial genomic fraganents of HBP gene （ GenBank accession number： KF652241 ） were amplified based on the sequences of an available contig in the EST-SNP database of largemouth bass. Three SNP mutation loci were identified in the 3＇ non-ceding region of HBP gene by direct sequencing, including H1 （G ＋ 2782T）, 142 （T ＋ 2817C） and H3 （G ＋ 2857A）. Three SNP loci of 165 randomly selected largemouth bass individuals were detected and genotyped by SnaPshot assay. Genetic structure was analyzed by POPGENE32 software. By using spssl7.0 software, a general linear model （GLM） was established for correlation analysis between different genotypes at SNP loci of HBP gene and various growth traits. The results showed that three SNP loci were in Hardy-Weinberg equilibrium state. To be specific, loci H1 and H2 formed two haplotypes （ A and B）, and three geno- types （AA, AB, and BB） were observed; loci H1, H2 and H3 formed six diplotypes （DI, I）2, D3, D4, D5 and D6）. According to the correlations between dif- ferent genotypes and various growth traits, the body weight and total length of largemouth bass individuals with genotype BB were significantly higher than those of individuals with genotype AB （ P 〈 0.05 ） ; the body weight and total length of largemouth bass individuals with diplotype D6 were significantly higher than those of individuals with diplotype D4 （P 〈0.05）. In this study, SNP markers correlated with growth traits were obtained in the 3＇ non-coding region ofHBP gene in large-mouth bass, which could be used as candidate genetic markers for subsequent molecular marker-assisted selection breeding of largemouth bass.展开更多
Characteristic features of austenitic steel grades combine a good corrosion resistance with a low hardness, wear resistance and scratch resistance. An interesting possibility for improving the wear behaviour of these ...Characteristic features of austenitic steel grades combine a good corrosion resistance with a low hardness, wear resistance and scratch resistance. An interesting possibility for improving the wear behaviour of these steels without loss of their corrosion resistance lies in enriching the near surface region with nitrogen. The process of a solution nitriding allows the rise of the solution of nitrogen in the solid phase. On this state nitrogen increases the corrosion resistance and the tribilogical load-bearing capacity. The aim of the study was, to investigate the improvement of the pitting corrosion behaviour by solution nitriding. A special topic was to observe the effect of nitrogen by different molybdenum content. So austenitic stainless steels (18% Cr, 12% Ni, Mo gradation between 0.06 to 3.6%) had been solution nitrided. The samples could be prepared with various surface content of nitrogen from 0.04 to 0.45% with a step-by-step grinding. The susceptibility against pitting corrosion of these samples had been tested by determination of the stable pitting potential in 0.5M and 1M NaCl at 25°C. For the investigated steel composition and the used corrosion system there is no influence of molybdenum on the effectiveness of nitrogen. The influence of nitrogen to all of the determined parameters can be described well by PRE = Cr + 3,3 * Mo + 25 *N. XPS analysis of the sample surfaces support the results of the pitting corrosion tests.Additionally surface investigations with an acid elektolyte (0,1M HC1 + 0,4M NaCl) were performed. In this case the passivation effective nitrogen content increases markedly with rising molybdenum concentration of the steel. Obviously an interaction of Mo and N is connected with a strongly acid electrolyte.展开更多
文摘Microstructure of the deepest zone of high speed steel W6Mo5Cr4V2(M2)melt after laser fu-sion was found to be so fine as the ehill zone of a solidified ingot.When narrower chill zoneformed,the long columnar dendrites grow into the melt and then the fine equiaxed cellularstructure appears in upper melt region nearly surface.The substructure of cellular grains anddendrites was observed to consist of martensite and retained austenile,while the carbides asM_6C_■ Cr_7C_3 and MC distributed at their boundaries.It is believed that the highermicrohardness up to HV_(0.1)=865-960 of the laser fused structure of the alloy is due to the oc-currence of martensite.
基金Project (05YB31) supported by the Scientific Research Initial Foundation for Doctor of Shenyang Institute of Aeronautical Engineering,China
文摘The NiAl-28Cr-5.85Mo-0.15Hf alloy was prepared by high-pressure die casting (HPDC) and subsequent hot isostatic pressing(HIP), and tested for compressible strength and fracture behavior at 300-1 373 K. The results show that the elevated temperature 0.2% compressible yield strength as well as the room-temperature compressible fracture strain of as-HIP alloy are larger than those of the same alloy prepared by directional solidification (DS). It suggests that the fine structures with a homogeneous distribution of fine Cr (Mo) and Hf-rich phase created by high-pressure die casting lead to these improvements.
基金Project supported by the National Basic Research Program of China(Grant No.2011CBA00607)the National Natural Science Foundation of China(Grant Nos.61106089 and 61376097)the Zhejiang Provincial Natural Science Foundation of China(Grant No.LR14F040001)
文摘A novel trench MOS barrier Schottky diode（TMBS） device with a high-k material introduced into the gate insulator is reported, which is named high-k TMBS. By simulation with Medici, it is found that the high-k TMBS can have 19.8% lower leakage current while maintaining the same breakdown voltage and forward turn-on voltage compared with the conventional regular trench TMBS.
文摘The catalysts were prepared by the temperature programmed reaction (TPR) of MoO3 with NH3 at various temperatures in the range of 573K～973K, and their hydrodenitrogenation (HDN) activities were tested in situ.It is shown that molybdenum nitrid(Mo2N) was formed above 923K and its intermediate MoO2 formed at about 573～623K under the rapid (5K/min.) TPR conditions.Mo2N is the most active species for pyridine HDN among MoO3,MoO2,MoS2,and Mo2N. Moreover,it can be promoted by adding Ni component.It is shown that the Ni/Mo2N catalyst prepared by adding some NiO into the precursor MoO3 has a steady HDN activity Which is far higher than that of the commercial sulfided NiMo/Al2O3(HR346) catalyst.
基金Supported by National Natural Science Foundation of China(No.31201985)National Key Technology Support Program of China(2012BAD26B03)"948"Key Program of the Ministry of Agriculture of China(2011-G12)
文摘High density lipoprotein binding protein （HBP） plays an important role in lipid metabolism of animals. Lipids are indispensable energy materials for fi- shes, especially for carnivorous fishes with low utilization efficiency of carbohydrates. The single nucleotide polymorphism （SNP） of HBP gene may affect the fat metabolism, thereby exerting an effect on the growth traits of largemouth bass （Micropterus salmoides）. Investigating the correlations between SNP and growth traits can provide candidate markers for molecular marker-assisted selection. In this study, partial genomic fraganents of HBP gene （ GenBank accession number： KF652241 ） were amplified based on the sequences of an available contig in the EST-SNP database of largemouth bass. Three SNP mutation loci were identified in the 3＇ non-ceding region of HBP gene by direct sequencing, including H1 （G ＋ 2782T）, 142 （T ＋ 2817C） and H3 （G ＋ 2857A）. Three SNP loci of 165 randomly selected largemouth bass individuals were detected and genotyped by SnaPshot assay. Genetic structure was analyzed by POPGENE32 software. By using spssl7.0 software, a general linear model （GLM） was established for correlation analysis between different genotypes at SNP loci of HBP gene and various growth traits. The results showed that three SNP loci were in Hardy-Weinberg equilibrium state. To be specific, loci H1 and H2 formed two haplotypes （ A and B）, and three geno- types （AA, AB, and BB） were observed; loci H1, H2 and H3 formed six diplotypes （DI, I）2, D3, D4, D5 and D6）. According to the correlations between dif- ferent genotypes and various growth traits, the body weight and total length of largemouth bass individuals with genotype BB were significantly higher than those of individuals with genotype AB （ P 〈 0.05 ） ; the body weight and total length of largemouth bass individuals with diplotype D6 were significantly higher than those of individuals with diplotype D4 （P 〈0.05）. In this study, SNP markers correlated with growth traits were obtained in the 3＇ non-coding region ofHBP gene in large-mouth bass, which could be used as candidate genetic markers for subsequent molecular marker-assisted selection breeding of largemouth bass.
基金The DFG(Deutsche Forschungsgemeinschaft)is gratefully acknowledged for the financial support(DFG No.PA 699/3-1 and FR 1603/1-2).
文摘Characteristic features of austenitic steel grades combine a good corrosion resistance with a low hardness, wear resistance and scratch resistance. An interesting possibility for improving the wear behaviour of these steels without loss of their corrosion resistance lies in enriching the near surface region with nitrogen. The process of a solution nitriding allows the rise of the solution of nitrogen in the solid phase. On this state nitrogen increases the corrosion resistance and the tribilogical load-bearing capacity. The aim of the study was, to investigate the improvement of the pitting corrosion behaviour by solution nitriding. A special topic was to observe the effect of nitrogen by different molybdenum content. So austenitic stainless steels (18% Cr, 12% Ni, Mo gradation between 0.06 to 3.6%) had been solution nitrided. The samples could be prepared with various surface content of nitrogen from 0.04 to 0.45% with a step-by-step grinding. The susceptibility against pitting corrosion of these samples had been tested by determination of the stable pitting potential in 0.5M and 1M NaCl at 25°C. For the investigated steel composition and the used corrosion system there is no influence of molybdenum on the effectiveness of nitrogen. The influence of nitrogen to all of the determined parameters can be described well by PRE = Cr + 3,3 * Mo + 25 *N. XPS analysis of the sample surfaces support the results of the pitting corrosion tests.Additionally surface investigations with an acid elektolyte (0,1M HC1 + 0,4M NaCl) were performed. In this case the passivation effective nitrogen content increases markedly with rising molybdenum concentration of the steel. Obviously an interaction of Mo and N is connected with a strongly acid electrolyte.
