Analysis of the Flow Field and Impact Force in High-Pressure Water Descaling

This study aims to improve the performances of the high-pressure water descaling technology used in steel hot rolling processes.In particular,a 2050 mm hot rolling line is considered,and the problem is investigated by means of a fluid–structure interaction(FSI)method by which the descaling effect produced by rolling coils with different section sizes is examined.Assuming a flat fan-shaped nozzle at the entrance of the R1R2 roughing mill,the outflow field characteristics and the velocity distribution curve on the strike line(at a target distance of 30–120 mm)are determined.It is found that the velocity in the center region of the water jet with different target distances is higher than that in the boundary region.As the target distance increases,the velocity of the water jet in the central region decreases.Through comparison with experimental results,it is shown that the simulation model can accurately predict the impact position of the high-pressure water on the impact plate,thereby providing a computational scheme that can be used to optimize the nozzle space layout and improve the slabs’descent effect for different rolling specifications.

Experimental investigation on using CO_(2)/H_(2)O emulsion with high water cut in enhanced oil recovery

CO_(2) emulsions used for EOR have received a lot of interest because of its good performance on CO_(2)mobility reduction.However,most of them have been focusing on the high quality CO_(2) emulsion(high CO_(2) fraction),while CO_(2) emulsion with high water cut has been rarely researched.In this paper,we carried out a comprehensive experimental study of using high water cut CO_(2)/H_(2)O emulsion for enhancing oil recovery.Firstly,a nonionic surfactant,alkyl glycosides(APG),was selected to stabilize CO_(2)/H_(2)O emulsion,and the corresponding morphology and stability were evaluated with a transparent PVT cell.Subsequently,plugging capacity and apparent viscosity of CO_(2)/H_(2)O emulsion were measured systematically by a sand pack displacement apparatus connected with a 1.95-m long capillary tube.Furthermore,a high water cut(40 vol%) CO_(2)/H_(2)O emulsion was selected for flooding experiments in a long sand pack and a core sample,and the oil recovery,the rate of oil recovery,and the pressure gradients were analyzed.The results indicated that APG had a good performance on emulsifying and stabilizing CO_(2) emulsion.An inversion from H_(2)O/CO_(2) emulsion to CO_(2)/H_(2)O emulsion with the increase in water cut was confirmed.CO_(2)/H_(2)O emulsions with lower water cuts presented higher apparent viscosity,while the optimal plugging capacity of CO_(2)/H_(2)O emulsion occurred at a certain water cut.Eventually,the displacement using CO_(2)/H_(2)O emulsion provided 18.98% and 13.36% additional oil recovery than that using pure CO_(2) in long sand pack and core tests,respectively.This work may provide guidelines for EOR using CO_(2) emulsions with high water cut.

Analysis of the Risk of Water Breakout in the Bottom Plate of High-Intensity Mining of Extra-Thick Coal Seams

In order to clarify the danger of water breakout in the bottom plate of extra-thick coal seam mining, 2202 working face of a mine in the west is taken as the research object, and it is proposed to use the on-site monitoring means combining borehole peeping and microseismic monitoring, combined with the theoretical analysis to analyze the danger of water breakout in the bottom plate. The results show that: 1) the theoretically calculated maximum damage depth of the bottom plate is 27.5 m, and its layer is located above the Austrian ash aquifer, which has the danger of water breakout;2) the drill hole peeping at the bottom plate of the working face shows that the depth of the bottom plate fissure development reaches 26 m, and the integrity of the water barrier layer has been damaged, so there is the risk of water breakout;3) for the microseismic monitoring of the anomalous area, the bottom plate of the return air downstream channel occurs in the field with a one-week lag, which shows that microseismic monitoring events may reflect the water breakout of the underground. This shows that the microseismic monitoring events can reflect the changes of the underground flow field, which can provide a reference basis for the early warning of water breakout. The research results can provide reference for the prediction of sudden water hazard.

Irrigating with cooler water does not reverse high temperature impact on grain yield and quality in hybrid rice

Rice grain yield and quality are negatively impacted by high temperature stress.Irrigation water temperature significantly affects rice growth and development,thus influencing yield and quality.The role of cooler irrigation water in counteracting high temperature induced damages in rice grain yield and quality are not explored.Hence,in the present study two rice hybrids,Liangyoupeijiu(LYPJ)and IIyou 602(IIY602)were exposed to heat stress and irrigated with water having different temperatures in a splitsplit plot experimental design.The stress was imposed starting from heading until maturity under field-based heat tents,over two consecutive years.The maximum day temperature inside the heat tents was set at 38℃.For the irrigation treatments,two different water sources were used including belowground water with cooler water temperature and pond water with relatively higher water temperature.Daytime mean temperatures in the heat tents were increased by 1.2–2.0℃ across two years,while nighttime temperature remained similar at both within and outside the heat tents.Cooler belowground water irrigation did have little effect on air temperature at the canopy level but decreased soil temperature(0.2–1.4℃)especially under control.Heat stress significantly reduced grain yield(33%to 43%),panicles m^(-2)(9%to 10%),spikelets m^(-2)(15%to 22%),grain-filling percentage(13%to 26%)and 1000-grain weight(3%to 5%).Heat stress significantly increased chalkiness and protein content and decreased grain length and amylose content.Grain yield was negatively related to air temperature at the canopy level and soil temperature.Whereas grain quality parameters like chalkiness recorded a significantly positive association with both air and soil temperatures.Irrigating with cooler belowground water reduced the negative effect of heat stress on grain yield by 8.8%in LYPJ,while the same effect was not seen in IIY602,indicating cultivar differences in their response to irrigation water temperature.Our findings reveal that irrigating with cooler belowground water would not significantly mitigate yield loss or improve grain quality under realistic field condition.The outcome of this study adds to the scientific knowledge in understanding the interaction between heat stress and irrigation as a mitigation tool.Irrigation water temperature regulation at the rhizosphere was unable to counteract heat stress damages in rice and hence a more integrated management and genetic options at canopy levels should be explored in the future.

Performance evaluation of CLM5.0 in simulating liquid soil water in high mountainous area,Northwest China

The model performance in simulating soil water content(SWC) is crucial for successfully modeling earth’s system,especially in high mountainous areas.In this study,the performance of Community Land Model 5.0(CLM5.0) in simulating liquid SWC was evaluated against observations from nine in-situ sites in the upper reach of the Heihe River Watershed(HRW),Northwest China.The CLM5.0 shows reliable performance in the study area with correlation coefficients(R) ranging between 0.79–0.93,root mean standard errors(RMSE)ranging between 0.044–0.097 m^(3)/m^(3),and the mean bias(BIAS) ranging between-0.084–0.061 m^(3)/m^(3).The slightly worse performance of CLM5.0 than CLM4.5 on alpine meadow and grassland is mainly caused by the revised canopy interception parameterization.The CLM5.0 overestimates interception and underestimates evapotranspiration(ET) on both alpine meadow and grassland during the growth period.The systematical overestimations at all the grassland sites indicate that the underestimation of ET is much larger than the overestimation of interception on grassland during growth period,while the errors of simulated interception and ET are partially canceled out on alpine meadow.Moreover,the underestimation of ET is more responsible for the overestimation of SWC than the overestimation of interception in the high mountainous area.It is necessary to estimate reasonable empirical parameter α(proportion of leaf water collection area) in interception parameterization scheme and further improve the dry surface layerbased soil evaporation resistance parameterization introduced in CLM5.0 in future researches.The performance of CLM5.0 is better under completely frozen stage than thawing stage and freezing stage,because of low variations of liquid SWC caused by extremely low hydraulic conductivity of soils.The underestimation of liquid SWC under frozen state is caused by underestimation of soil temperature,which leads to more ice mass and less liquid water in total water content.

A Hydrogen Iron Flow Battery with High Current Density and Long Cyclability Enabled Through Circular Water Management

The hydrogen-iron(HyFe)flow cell has great potential for long-duration energy storage by capitalizing on the advantages of both electrolyzers and flow batteries.However,its operation at high current density(high power)and over continuous cycling testing has yet to be demonstrated.In this paper,we discuss our design and demonstration of a water management strategy that supports high current and long cycling performance of a HyFe flow cell.Water molecules associated with the movement of protons from the iron electrode to the hydrogen electrode are sufficient to hydrate the membrane and electrode at a low current density of 100 mA cm^(-2)during the charge process.At higher charge current density,more aggressive measures must be taken to counter back-diffusion driven by the acid concentration gradient between the iron and hydrogen electrodes.Our water management approach is based on water vapor feeding in the hydrogen electrode,and water evaporation in the iron electrode,thus enabling the high current density operation of 300 mA cm^(-2).

High Order Finite Difference WENO Methods for Shallow Water Equations on Curvilinear Meshes

A high order finite difference numerical scheme is developed for the shallow water equations on curvilinear meshes based on an alternative flux formulation of the weighted essentially non-oscillatory(WENO)scheme.The exact C-property is investigated,and comparison with the standard finite difference WENO scheme is made.Theoretical derivation and numerical results show that the proposed finite difference WENO scheme can maintain the exact C-property on both stationarily and dynamically generalized coordinate systems.The Harten-Lax-van Leer type flux is developed on general curvilinear meshes in two dimensions and verified on a number of benchmark problems,indicating smaller errors compared with the Lax-Friedrichs solver.In addition,we propose a positivity-preserving limiter on stationary meshes such that the scheme can preserve the non-negativity of the water height without loss of mass conservation.

High Water Resistance and Enhanced Mechanical Properties of Bio-Based Waterborne Polyurethane Enabled by in-situ Construction of Interpenetrating Polymer Network

In this study,acrylic acid was used as a neutralizer to prepare bio-based WPU with an interpenetrating polymer network structure by thermally induced free radical emulsion polymerization.The effects of the content of acrylic acid on the properties of the resulting waterborne polyurethane-poly(acrylic acid)(WPU-PAA)dispersion and the films were systematically investigated.The results showed that the cross-linking density of the interpenetrating network polymers was increased and the interlocking structure of the soft and hard phase dislocations in the molecular segments of the double networks was tailored with increasing the content of acrylic acid,leading to enhancement of the mechanical properties and water resistance of WPU-PAA films.Notably,with the increase in content of acrylic acid,the tensile strength,Young’s modulus,and toughness of the WPU-PAA-110 film increased by 3 times,and 8 times,and 2.4 times compared with WPU-PAA-80,respectively.The WPU-PAA-100 film showed the best water resistance,and the water absorption rate at 96 h was only 3.27%.This work provided a new design scheme for constructing bio-based WPU materials with excellent properties.

Design and analysis of a high loss density motor cooling system with water cold plates

Aiming at reducing the difficulty of cooling the interior of high-density motors,this study proposed the placement of a water cold plate cooling structure between the axial laminations of the motor stator.The effect of the cooling water flow,thickness of the plate,and motor loss density on the cooling effect of the water cold plate were studied.To compare the cooling performance of water cold plate and outer spiral water jacket cooling structures,a high-speed permanent magnet motor with a high loss density was used to establish two motor models with the two cooling structures.Consequently,the cooling effects of the two models were analyzed using the finite element method under the same loss density,coolant flow,and main dimensions.The results were as follows.(1)The maximum and average temperatures of the water cold plate structure were reduced by 25.5%and 30.5%,respectively,compared to that of the outer spiral water jacket motor;(2)Compared with the outer spiral water jacket structure,the water cold plate structure can reduce the overall mass and volume of the motor.Considering a 100 kW high-speed permanent magnet motor as an example,a water cold plate cooling system was designed,and the temperature distribution is analyzed,with the result indicating that the cooling structure satisfied the cooling requirements of the high loss density motor.

Optimization of Injection Parameters for Profile Control and Flooding in an Oilfield during High Water Cut Period

In order to improve the effect of water control and oil stabilization during high water cut period, a mathematical model of five point method well group was established with the high water cut well group of an Oilfield as the target area, the variation law of water cut and recovery factor of different injection parameters was analyzed, and the optimization research of injection parameters of polymer enhanced foam flooding was carried out. The results show that the higher the injection rate, the lower the water content curve, and the higher the oil recovery rate. As the foam defoamed when encountering oil, when the injection time was earlier than 80% of water cut, the later the injection time was, the better the oil displacement effect would be. When the injection time was later than 80% of water cut, the later the injection time was, the worse the oil displacement effect would be. The larger the injection volume, the lower the water content curve and the higher the recovery rate. After the injection volume exceeded 0.2 PV, the amplitude of changes in water content and recovery rate slowed down. The optimal injection parameters of profile control agent for high water content well group in Oilfield A were: injection rate of 15 m3/d, injection timing of 80% water content, and injection volume of 0.2 PV.

Facile synthesis of composite polyferric magnesium-silicate-sulfate coagulant with enhanced performance in water and wastewater

The coagulation process is a widely applied technology in water and wastewater treatment.Novel composite polyferric mag-nesium-silicate-sulfate(PFMS)coagulants were synthesized using Na_(2)SiO_(3)·9H_(2)O,Fe_(2)(SO_(4))_(3),and MgSO_(4) as raw materials in this paper.The effects of aging time,Fe:Si:Mg,and OH:M molar ratios(M represents the metal ions)on the coagulation performance of the as-pre-pared PFMS were systematically investigated to obtain optimum coagulants.The results showed that PFMS coagulant exhibited good co-agulation properties in the treatment of simulated humic acid-kaolin surface water and reactive dye wastewater.When the molar ratio was controlled at Fe:Si:Mg=2:2:1 and OH:M=0.32,the obtained PFMS presented excellent stability and a high coagulation efficiency.The removal efficiency of ultraviolet UV254 was 99.81%,and the residual turbidity of the surface water reached 0.56 NTU at a dosage of 30 mg·L^(-1).After standing the coagulant for 120 d in the laboratory,the removal efficiency of UV254 and residual turbidity of the surface wa-ter were 88.12%and 0.68 NTU,respectively,which accord with the surface water treatment requirements.In addition,the coagulation performance in the treatment of reactive dye wastewater was greatly improved by combining the advantages of magnesium and iron salts.Compared with polyferric silicate-sulfate(PFS)and polymagnesium silicate-sulfate(PMS),the PFMS coagulant played a better decolor-ization role within the pH range of 7-13.

A hierarchical salt-rejection strategy for sustainable and high-efficiency solar-driven desalination

Solar steam generation(SSG)is widely regarded as one of the most sustainable technologies for seawater desalination.However,salt fouling severely compromises the evaporation performance and lifetime of evaporators,limiting their practical applications.Herein,we propose a hierarchical salt-rejection(HSR)strategy to prevent salt precipitation during long-term evaporation while maintaining a rapid evaporation rate,even in high-salinity brine.The salt diffusion process is segmented into three steps—insulation,branching diffusion,and arterial transport—that significantly enhance the salt-resistance properties of the evaporator.Moreover,the HSR strategy overcomes the tradeoff between salt resistance and evaporation rate.Consequently,a high evaporation rate of 2.84 kg m^(-2) h^(-1),stable evaporation for 7 days cyclic tests in 20 wt%NaCl solution,and continuous operation for 170 h in natural seawater under 1 sun illumination were achieved.Compared with control evaporators,the HSR evaporator exhibited a>54%enhancement in total water evaporation mass during 24 h continuous evaporation in 20 wt%salt water.Furthermore,a water collection device equipped with the HSR evaporator realized a high water purification rate(1.1 kg m^(-2) h^(-1)),highlighting its potential for agricultural applications.

Biodrying of municipal solid waste with high water content by combined hydrolytic-aerobic technology

The high water content of municipal solid waste(MSW)will reduce the effciency of mechanical sorting,consequently unfavorable for beneficial utilization.In this study,a combined hydrolytic-aerobic biodrying technology was introduced to remove water from MSW.The total water removals were proved to depend on the ventilation frequency and the temporal span in the hydrolytic stage. The ventilation frequency of 6 times/d was preferable in the hydrolytic stage.The hydrolytic span should not be prolonged more than ...

Spatial correlation of the high intensity zone in deep-water acoustic field

The spatial correlations of acoustic field have important implications for underwater target detection and other ap- plications in deep water. In this paper, the spatial correlations of the high intensity zone in the deep-water acoustic field are investigated by using the experimental data obtained in the South China Sea. The experimental results show that the structures of the spatial correlation coefficient at different ranges and depths are similar to the transmission loss structure in deep water. The main reason for this phenomenon is analyzed by combining the normal mode theory with the ray theory. It is shown that the received signals in the high intensity zone mainly include one or two main pulses which are contributed by the interference of a group of waterbome modes with similar phases. The horizontal-longitudinal correlations at the same receiver depth but in different high intensity zones are analyzed. At some positions, more pulses are received in the arrival structure of the signal due to bottom reflection and the horizontal-longitudinal correlation coefficient decreases accordingly. The multi-path arrival structure of receiving signal becomes more complex with increasing receiver depth.

Novel method for the determination of five carbamate pesticides in water samples by dispersive liquid-liquid microextraction combined with high performance liquid chromatography

A novel method for the determination of five carbamate pesticides （metolcarb, carbofuran, carbaryl, isoprocard and diethofencard） in water samples was developed by dispersive liquid-liquid microextraction （DLLME） coupled with high performance liquid chromatography-diode array detector （HPLC-DAD）. Some experimental parameters that influence the extraction efficiency were studied and optimized to obtain the best extraction results. Under the optimum conditions for the method, the calibration curve was linear in the concentration range from 5 to 1000 ng mL^-1 for all the five carbamate pesticides, with the correlation coefficients （r^2） varying from 0.9984 to 0.9994. Good enrichment factors were achieved ranging from 80 to 177- fold, depending on the compound. The limits of detection （LODs） （S/N = 3） were ranged from 0.1 to 0.5 ng mL^-1. The method has been successfully applied to the analysis of the pesticide residues in environmental water samples.

Treatment of mine water high in Fe and Mn by modified manganese sand

The iron and manganese absorption properties of several filter media were studied. Four plain filter media and six surface-modified media were examined. The surface modification was performed using potassium permanganate as a surface treatment. The surface-modified manganese sand was found to be most efficient at removing iron and manganese from water. The metal concentrations in filtered effluent were between 0.01 and 0.04 mg/L, which is far lower than the standard for recycle water. A concen-tration of 5% KMnO4 was found to be most effective as surface modifier. The surface of the manganese sand modified by 5% KMnO4 was examined and found to be covered with a dense membrane of some compound. The membrane had the advantages of uniform texture, large surface area and physical and chemical stability. It was effective at removing iron and manganese from mine water.

N‑Doped Graphene‑Decorated NiCo Alloy Coupled with Mesoporous NiCoMoO Nano‑sheet Heterojunction for Enhanced Water Electrolysis Activity at High Current Density

Developing highly effective and stable non-noble metalbased bifunctional catalyst working at high current density is an urgent issue for water electrolysis(WE).Herein,we prepare the N-doped graphene-decorated NiCo alloy coupled with mesoporous NiCoMoO nano-sheet grown on 3D nickel foam(NiCo@C-NiCoMoO/NF)for water splitting.NiCo@C-NiCoMoO/NF exhibits outstanding activity with low overpotentials for hydrogen and oxygen evolution reaction(HER:39/266 mV;OER:260/390 mV)at±10 and±1000 mA cm^(−2).More importantly,in 6.0 M KOH solution at 60℃ for WE,it only requires 1.90 V to reach 1000 mA cm−2 and shows excellent stability for 43 h,exhibiting the potential for actual application.The good performance can be assigned to N-doped graphene-decorated NiCo alloy and mesoporous NiCoMoO nano-sheet,which not only increase the intrinsic activity and expose abundant catalytic activity sites,but also enhance its chemical and mechanical stability.This work thus could provide a promising material for industrial hydrogen production.

Effect of carbon and nitrogen ratio control on Artemia growth, water quality, biofloc microbial diversity under high salinity and zero-water exchange culture condition

Biofloc technology has been applied successfully in the intensive aquaculture of several fish and shrimp species. The growth of heterotrophic microorganisms can be stimulated through adding extra carbon, which reduces the nitrogen level in the water and provides microbial protein to the animals. However, most of the studies and practical applications have been conducted in freshwater and marine environment. This paper focused on brine shrimp Artemia that lives in high salinity environment together with other halophilic or halotolerant microorganisms. The effect of carbon supplementation on Artemia growth, water quality, and microbial diversity of biofl ocs was studied in the closed culture condition without any water exchange. The salinity of the culture medium was 100. A 24-d culture trial was conducted through supplementing sucrose at carbon/nitrogen (C/N) ratio of 5, 15, and 30 (Su5, Su15, and Su30), respectively. The culture without adding sucrose was used as a control. Artemia was fed formulated feed at a feeding ration of 60% recommended feeding level. The results showed that sucrose supplementation at higher C/N ratio (15 and 30) signifi cantly improved the Artemia survival, growth and water quality ( P <0.05). Addition of sucrose at C/N ratio of 15 and 30 significantly increased biofloc volume (BFV)( P <0.05). The Illumina MiSeq sequencing analysis showed that supplementing carbon at C/N ratio of 15 had a better total bacterial diversity and richness, and shaped the microbial composition at genera level. This study should provide information for studying the mechanism of biofloc technology and its application in high salinity culture conditions.

Rock Breaking Performance of a Pick Assisted by High-pressure Water Jet under Different Configuration Modes

In the process of rock breaking, the conical pick bears great cutting force and wear, as a result, high-pressure water jet technology is used to assist with cutting. However, the effect of the water jet position has not been studied for rock breaking using a pick. Therefore, the models of rock breaking with different configuration modes of the water jet are established based on SPH combined with FEM. The effect of the water jet pressure, distance between the jet and the pick bit, and cutting depth on the rock breaking performance as well as a comparison of the tension and compression stress are studied via simulation; the simulation results are verified by experiments. The numerical and experimental results indicate that the decrease in the rates of the pick force obviously increases from 25 MPa to 40 MPa, but slowly after 40 MPa, and the optimal distance between the jet and the pick bit is 2 mm under the JFP and JSP modes. The JCP mode is proved the best, followed by the modes of JRP and JFP, and the worst mode is JSP. The decrease in the rates of the pick force of the JCP, JRP, JFP, and JSP modes are up to 30.96%, 28.96%, 33.46%, 28.17%, and 25.42%, respectively, in experiment. Moreover, the JSP mode can be regarded as a special JFP model when the distance between the pick-tip and the jet impact point is 0 mm. This paper has a dominant capability in introducing new numerical and experimental method for the study of rock breaking assisted by water jet and electing the best water jet position from four different configuration modes.

Design of a New Water Load for S-band 750 kW Continuous Wave High Power Klystron Used in EAST Tokamak

In order to test the klystrons operated at a frequency of 3.7 GHz in a continuous wave （CW） mode, a type of water load to absorb its power up to 750 kW is presented. The distilled water sealed with an RF ceramic window is used as the absorbent. At a frequency range of 70 MHz, the VSWR （Voltage Standing Wave Ratio） is below 1.2, and the rise in temperature of water is about 30 ℃ at the highest power level.