In order to solve the problem of broadband field probes calibration with only selected discrete frequencies above 1 GHz, a sweep-frequency calibration technology based on a coaxial conical（co-conical） cell is resear...In order to solve the problem of broadband field probes calibration with only selected discrete frequencies above 1 GHz, a sweep-frequency calibration technology based on a coaxial conical（co-conical） cell is researched. Existing research is only qualitative because of the complexity of theoretical calculations. For designing a high performance cell, a mathematic model of high-order modes transmission is built according to the geometrical construction of co-conical. The associated Legendre control functions of high-order modes are calculated by using recursion methodology and the numerical calculation roots are presented with different half angles of inner and outer conductor. Relationship between roots and high-order modes transmission is analyzed, when the half angles of inner conductor and outer conductor are θ1=1.5136° and θ2=8° respectively, the co-conical cell has better performance for fewer transmitting high-order modes. The propagation process of the first three transmitting modes wave is simulated in CST-MWS software from the same structured co-conical. The simulation plots show that transmission of high-order modes appears with electromagnetic wave reflection, then different high-order mode transmission has different cut-off region and each cut-off region is determined by its cut-off wavelength. This paper presents numerical calculation data and theoretical analysis to design key structural parameters for the co-conical transverse electromagnetic wave cell（co-conical TEM cell）.展开更多
Injection recovery is an important measure for increasing the oil recovery rate of an oil field. One way is that centrifugal pumps or plunger pumps are used in an injection station to responsible for injection over a ...Injection recovery is an important measure for increasing the oil recovery rate of an oil field. One way is that centrifugal pumps or plunger pumps are used in an injection station to responsible for injection over a large area under the same pressure. This method is ineffective for low-permeability layers. For the oilfields in dispersed distribution in the marginal areas of Daqing, the low water-absorbing section needs an injection with a high delivery pressure and a low discharge capacity; another way is to install the submersible electric pump upside down, but because the submersible electric pump and the motor are underground, it is difficult for installation and maintenance. Introduced in this paper is the development and application of a surface high-pressure injection device with a submersible electric pump. Bysuccessful resolving some problems, such as the axial force of the submersible electric pump, sealing, level regulation of the pump, coaxiality and vibration, the device has the good points of running smoothly, moving easily, installation and maintains quickly and long period of running. This device can effectively solve the injection of the low water-absorbing section and of oilfields in dispersed locations. The recovery rate of oilfields is also enhanced.展开更多
An all-metal slow-wave structure, coaxial-radial line, which is suitable for application in broadband high power traveling wave tube (TWT) and relativistic TWT as a RF system is introduced. Making use of the field mat...An all-metal slow-wave structure, coaxial-radial line, which is suitable for application in broadband high power traveling wave tube (TWT) and relativistic TWT as a RF system is introduced. Making use of the field matching method and variational method together with the orthogonality of the Bessel function and the Floquet Theroem for the periodic system, the dispersion characteristic expression is derived. This equation is more rigorous than that of precious reports.展开更多
在大功率工作环境中,射频电路经常发生电磁泄漏(Electro Magnetic Leak,EML)和无源互调(Passive Inter-Modulation,PIM)等现象。而在同轴谐振器中,不稳定连接缝隙处成为增加电磁泄漏EML和PIM问题风险的隐患部位。文章通过对同轴谐振器...在大功率工作环境中,射频电路经常发生电磁泄漏(Electro Magnetic Leak,EML)和无源互调(Passive Inter-Modulation,PIM)等现象。而在同轴谐振器中,不稳定连接缝隙处成为增加电磁泄漏EML和PIM问题风险的隐患部位。文章通过对同轴谐振器等效电路建模和电磁场建模给出了缝隙位置与电磁场表面电流的关系,并分析了3种不同结构同轴谐振腔EML特性。结果表明通过微调连接缝隙,使其有效偏离同轴谐振器的电流波幅点位置,可以降低大功率同轴谐振器的连接泄漏,从而减小无源互调的风险。依据分析结果选取了3种同轴结构(单螺钉连接、法兰内连接、法兰外连接)中连接泄露最小的结构作为大功率器件的基本结构,小批量器件在大功率测试和试验中无EML和PIM现象。展开更多
基金Supported by State Administration of Science Technology and Industry for National Defense,China(Grant No.JSJC2013204B301)
文摘In order to solve the problem of broadband field probes calibration with only selected discrete frequencies above 1 GHz, a sweep-frequency calibration technology based on a coaxial conical（co-conical） cell is researched. Existing research is only qualitative because of the complexity of theoretical calculations. For designing a high performance cell, a mathematic model of high-order modes transmission is built according to the geometrical construction of co-conical. The associated Legendre control functions of high-order modes are calculated by using recursion methodology and the numerical calculation roots are presented with different half angles of inner and outer conductor. Relationship between roots and high-order modes transmission is analyzed, when the half angles of inner conductor and outer conductor are θ1=1.5136° and θ2=8° respectively, the co-conical cell has better performance for fewer transmitting high-order modes. The propagation process of the first three transmitting modes wave is simulated in CST-MWS software from the same structured co-conical. The simulation plots show that transmission of high-order modes appears with electromagnetic wave reflection, then different high-order mode transmission has different cut-off region and each cut-off region is determined by its cut-off wavelength. This paper presents numerical calculation data and theoretical analysis to design key structural parameters for the co-conical transverse electromagnetic wave cell（co-conical TEM cell）.
文摘Injection recovery is an important measure for increasing the oil recovery rate of an oil field. One way is that centrifugal pumps or plunger pumps are used in an injection station to responsible for injection over a large area under the same pressure. This method is ineffective for low-permeability layers. For the oilfields in dispersed distribution in the marginal areas of Daqing, the low water-absorbing section needs an injection with a high delivery pressure and a low discharge capacity; another way is to install the submersible electric pump upside down, but because the submersible electric pump and the motor are underground, it is difficult for installation and maintenance. Introduced in this paper is the development and application of a surface high-pressure injection device with a submersible electric pump. Bysuccessful resolving some problems, such as the axial force of the submersible electric pump, sealing, level regulation of the pump, coaxiality and vibration, the device has the good points of running smoothly, moving easily, installation and maintains quickly and long period of running. This device can effectively solve the injection of the low water-absorbing section and of oilfields in dispersed locations. The recovery rate of oilfields is also enhanced.
基金Supported by the Fund of National Key Laboratory (No.51440020101DZ7604)
文摘An all-metal slow-wave structure, coaxial-radial line, which is suitable for application in broadband high power traveling wave tube (TWT) and relativistic TWT as a RF system is introduced. Making use of the field matching method and variational method together with the orthogonality of the Bessel function and the Floquet Theroem for the periodic system, the dispersion characteristic expression is derived. This equation is more rigorous than that of precious reports.
文摘在大功率工作环境中,射频电路经常发生电磁泄漏(Electro Magnetic Leak,EML)和无源互调(Passive Inter-Modulation,PIM)等现象。而在同轴谐振器中,不稳定连接缝隙处成为增加电磁泄漏EML和PIM问题风险的隐患部位。文章通过对同轴谐振器等效电路建模和电磁场建模给出了缝隙位置与电磁场表面电流的关系,并分析了3种不同结构同轴谐振腔EML特性。结果表明通过微调连接缝隙,使其有效偏离同轴谐振器的电流波幅点位置,可以降低大功率同轴谐振器的连接泄漏,从而减小无源互调的风险。依据分析结果选取了3种同轴结构(单螺钉连接、法兰内连接、法兰外连接)中连接泄露最小的结构作为大功率器件的基本结构,小批量器件在大功率测试和试验中无EML和PIM现象。
