Surface modification of Cu-25Cr alloy induced by high current pulsed electron beam

A Cu-25Cr alloy prepared by vacuum induction melting method was treated by the high current pulsed electron beam （HCPEB） with pulse numbers ranging from 1 to 100. Surface morphologies and microstructures of the alloy before and after the treatment were investigated by scanning electron microscopy and X-ray diffraction. The results show that significant surface modification can be induced by HCPEB with the pulse number reaching 10. Craters with typical morphologies on the Cu-25Cr alloy surface are formed due to the dynamic thermal field induced by the HCPEB. Micro-cracks, as a unique feature, are well revealed in the irradiated Cu-25Cr specimens and attributed to quasi-static thermal stresses accumulated along the specimen surface. The amount of cracks is found to increase with the pulse number and a preference of these cracks to Cr phases rather than Cu phases is also noted. Another characteristic produced by the HCPEB is the fine Cr spheroids, which are determined to be due to occurrence of liquid phase separation in the Cu-25Cr alloy. In addition, an examination on surface roughness of all specimens reveals that more pulses will produce a roughened surface, as a result of compromising the above features.

A study of pulsed high voltage driven hollow-cathode electron beam sources through synchronous optical trigger

In this study,a pulsed,high voltage driven hollow-cathode electron beam sources through an optical trigger is designed with characteristics of simple structure,low cost,and easy triggering.To validate the new design,the characteristics of hollow-cathode discharge and electron beam characterization under pulsed high voltage drive are studied experimentally and discussed by discharge characteristics and analyses of waveform details,respectively.The validation experiments indicate that the pulsed high voltage supply significantly improves the frequency and stability of the discharge,which provides a new solution for the realization of a high-frequency,high-energy electron beam source.The peak current amplitude in the high-energy electron beam increases from 6.2 A to 79.6 A,which indicates the pulsed power mode significantly improves the electron beam performance.Besides,increasing the capacitance significantly affects the highcurrent,lower-energy electron beam more than the high-energy electron beam.

Compounded Surface Modification of ZK60 Mg Alloy by High Current Pulsed Electron Beam+Micro-plasma Oxidation

In this study, compounded surface modification technology-high current pulsed electron beam （HCPEB） ＋ micro-plasma oxidation （MPO） was applied to treat ZK60 Mg alloys. The characteristics of the microstructure of ZK60 Mg alloy after single MPO and HCPEB＋MPO compounded treatment were investigated by SEM. The results showed that the density of the ceramic layer of HCPEB＋MPO-treated ZK60 Mg alloy was improved and defects were reduced compared to that under MPO treatment alone. Surface modified layer of ZK60 Mg alloys treated by HCPEB＋MPO was divided into three zones, namely the top loose ceramic zone, middle compact zone and inside HCPEB-induced melted zone. Corrosion resistance of ZK60 Mg alloy before and after the compounded surface modification was measured in a solution of 3.5% NaCl by potentiodynamic polarization curves. It was found that the corrosion current density of ZK60 Mg alloys could be reduced by about three orders of magnitude, from 311μA/cm^2 of the original sample to 0.2μA/cm^2 of the HCPEB＋MPO-treated sample. This indicates the great application potential of the HCPEB＋MPO compounded surface modification technology in improving the corrosion resistance of ZK60 Mg alloys in the future.

Improvement of Wear Resistance of Magnesium Alloy AZ91HP by High Current Pulsed Electron Beam Treatment

Surface modification of magnesium alloy AZ91HP (9wt%Al, 0.5wt%Zn, 0.5wt%Mn, Mg remaining percentage) by high current pulsed electron beam (HCPEB) treatment was studied in this paper. The secondary phase MgnAln is nearly completely dissolved and as a result, a super-saturated solid solution forms on the re-melted surface. The microhardness is increased both in and far beyond the heat-affected zone (HAZ), reaching about 250um. Measurements on sliding wear have shown that the wear resistance of the treated samples was improved by a factor of about 2.4 as compared to the as-received sample. It is also found that the sliding wear resistance can be further improved by surface alloying with TiN.

Improvement of wear resistance of AZ31 and AZ91HP by high current pulsed electron beam treatment

The surface modification of magnesium alloys (AZ31 and AZ91HP) was studied by a high current pulsed electron beam(HCPEB). The results show that the cross-sectional microhardness of treated samples increases not only in the heat affected zone(HAZ), but also beyond HAZ, reaching over 250μm. This is due to the action of quasi-static thermal stress and the shock thermal stress wave with materials, which result in its fast deformation on the surface layer and so increases microhardness. For the AZ91HP alloy, a nearly complete dissolution of the intermetallic phase Mg_ 17Al_ 12 is observed, and a super-saturated solid solution forms on the re-melted surface, which is due to the solute trapping effect during the fast solidification process. Measurements on sliding wear show that wear resistance is improved by approximately 5.6 and 2.4 times for the AZ31 and AZ91HP respectively, as compared with as-received samples.

Characterizing modified surface layer of 316L stainless steel treated by high current pulsed electron beam

High current pulsed electron beam(HCPEB) is now developing as a useful tool for surface modification of materials.When concentrated electron flux transferring its energy into the surface layer of target material within a short pulse time,coupled thermal and stress processes would lead to the formation of metastalbe microstructure with improved properties.In the present work,HCPEB treatment of 316L stainless steel(SS) was carried out and the microstructural changes in modified surface layer were characterized with optical microscopy,X-ray diffractometry and electron backscatter diffractometry(EBSD) techniques.The corrosion resistance of modified surface was measured in a 5wt.% salt solution.The evolution regularity of surface craters and grain refinement effect,as well as the preferred orientation of(111) crystal plane occurring in the HCPEB treatment under different working parameters were discussed along with their influence on corrosion resistance.

HIGH-CURRENT PULSED ELECTRON BEAM: RAPID SURFACE ALLOYING AND WEAR RESISTANCE IMPROVEMENT

The present paper reports the rapid surface alloying induced by the bombardment of high-current pulsed electron beam. Two kinds of substrate materials were examined to show this effect. The first sample was a pure Al metal pre-coated with fine carbon powders prior to the bombardment, and the second alloy is the D2-Crl2MolVl mould steel pre-coated with Cr, Ti, and TiN powders. The surface elements diffuse about several micrometers into the substrate materials only after several bombardments. Tribological behaviors of these samples were characterized and significant improvement in wear resistance was found. Finally, a TEM analysis reveals the presence of stress waves generated by coupled thermal and stress fields, which was considered as the main cause of the enhanced properties.

Numerical simulation of thermal-mechanical process of Al-Si-Pb alloy treated by high current pulsed electron beam

The modified microstructure of Al-Si-Pb alloys irradiated by high current electron beam (HCPEB) reveals three distinct regions: a molten zone, an overlapped zone of heat-affected and quasistatic thermal stress-affected zone, and a transition zone followed by the substrate. The hardness and wear properties of the alloys were significantly improved. To better understand these changes in microstructure and properties, the physical model for the simulation of temperature and quasistatic stress fields was established. Based on experimental investigation and physical models, the temperature field and stress field were simulated for Al-Si-Pb alloy. The starting melting position, largest crater depth, melting layer thickness, and quasistatic stress distribution were obtained. These results reveal the mechanism of crater formation on the surface and improvement of hardness and wear resistance.

Microstructure and properties of Nb/Ta multilayer films irradiated by a high current pulse electron beam

Nb/Ta multilayer films deposited on Ti6A14V substrate with Nb and Ta monolayer thicknesses of 30 nm, 120 nm, and 240 nm were irradiated by a high current pulse electron beam （HCPEB） to prepare Nb-Ta alloyed layers. The mi- crostructure and the composition of the outmost surface of melted alloyed layers were investigated using a transmission electron microscope （TEM） equipped with an X-ray energy dispersive spectrometer （EDS） attachment. The Ta content of the alloyed surface layer prepared from the monolayer of thickness 30 nm, 120 nm, and 240 nm was- 27.7 at.%, 6.37 at.%, and 0 at.%, respectively. It was found that the Ta content in the alloyed layer plays a dominant role in the microstructure of the films. The hardness and the wear rate of the alloyed layers decrease with the increasing content of Ta in the surface laver.

Development of a high current short pulse electron gun

Dielectric wall accelerator(DWA), towards high gradient acceleration field(30 MeV/m–100 MeV/m), is under development at Institute of Modern Physics. A prototype was designed and constructed to prove the principle. This needs a short pulse high current electron source to match the acceleration field generated by the Blumlein-type pulse forming lines(PFLs). In this paper, we report the design and test of a new type short pulse high current electron gun based on principle of vacuum arc discharge. Electron beams of 100 mA with pulse width of 10 ns were obtained.

Microstructure and property modifications in surface layers of a Mg-4Sm-2Al-0.5Mn alloy induced by pulsed electron beam treatments

In this work,surface modification of a Mg-4Sm-2Al-0.5Mn alloy with high current pulse electron beam(HCPEB)under different number of pulses were investigated.The evolution in microstructure,composition and phase components and properties in the surface layer before and after HCPEB treatment were characterized.It was found that the Al 11 Sm 3 and Al 2 Sm phases in the surface layer were gradually dissolved during HCPEB treatment,leading to the formation of a chemical homogeneous melted layers.Besides,deformation bands were formed in the treated layer due to the thermal stress generated during treatment.After 15 pulses treatment,the surface hardness increases to the maximum value of about 62.2 HV,about 61.2%higher than that of the untreated state.Electrochemical results show that the 15 pulses treated sample presents the best corrosion resistance in the 3.5wt%NaCl water solution by showing the highest corrosion potential(E_(corr))of-1.339V SEC and the lowest corrosion current density(I_(corr))of 1.48×10^(-6)A·cm^(-2).The results prove that the surface properties of the Mg-4Sm-2Al-0.5Mn alloy can be significantly improved by the HCPEB treatments under proper conditions.

A Pulsed Electromagnet for Laser Wakefield Electron Acceleration Experiments

Laser Wakefield plasma acceleration of electrons to energies above 10 GeV, may be possible in the new high power Laser beam facilities. The design of an Electron Spectrometer with an electro-magnet with adjustable magnetic field is proposed for the characterization of electron energy spectrum with a precision better than 10% for the entire energy range from 0.5 GeV to 38 GeV. The expected precision in the measurement of the electron energy is calculated as a function of the magnetic field, of the electron energy and of the magnet length. To outline the advantages offered by a pulsed electromagnet with high magnetic fields, the mass and the electric power lost in the coils of a 4 m long electromagnet with continuous current and Iron yoke are calculated.

Enhanced Surface Properties Induced by High Current Pulsed Electron Beam (HCPEB) Treatment

High current pulsed electron beam (HCPEB) has been developed as a useful tool for surface treatment of materials.In the present work,the fundamental principle of HCPEB source was described along with the device configuration and working parameters.Through the different kinds of HCPEB surface treatment experiments conducted,the enhanced surface properties induced by HPCEB treatment were illustrated and explained with their microstructure characterization results.

HCPEB作用下镀铝CoCrAlY涂层的表面微观结构状态

采用大气等离子喷涂在GH4169镍基高温合金表面沉积CoCrAlY涂层,利用电子束蒸发镀膜技术在涂层表面沉积纳米铝膜,分别对镀铝前后的涂层使用强流脉冲电子束进行辐照处理,对处理前后的涂层表面进行成分及结构分析.XRD结果显示,经过HCPEB轰击之后,涂层表面纳米铝膜重熔,钴类氧化物消失,新增铝相,且随着轰击次数增加,β-Co Al含量增加.结构分析表明,电子束轰击可以使原始涂层表面尖角、孔洞、夹杂等消失,形成非常致密的凸起胞状体纳米超细晶结构,有利于抑制腐蚀性气体的侵入,同时铝含量的增加有利于抗氧化性能的提高.

Surface alloying of Al films/Ti substrate based on high-current pulsed electron beams irradiation

Ti–Al surface alloy was fabricated using a cyclic pulsed liquid-phase mixing of predeposited 100 nm Al film with a-Ti substrate by low-energy high-current electron beam. Electron probe micro-analysis（EPMA）,grazing incidence X-ray diffraction analysis（GIXRD）,transmission electron microscopy（TEM）, and nanoindentation were used to investigate the characterization of Ti–Al surface alloy. The experimental results show that the thickness of alloy layer is ＊3 lm, and the content of Al in the ＊1 lm thickness surface layer is ＊60 at%. The tetragonal TiAl and TiAl2intermetallics were synthesized at the top surface, which have nanocrystalline structure.The main phase formed in the ＊2.5 lm thick surface is TiAl, and there are few TiAl2and Ti3Al phase for the alloy.Dislocation is enhanced in the alloyed layer. The nanohardness of Ti–Al surface alloy increased significantly compared with a-Ti substrate due to the nanostructure and enhanced dislocation. Since the e-beam remelted repeatedly, the Ti–Al surface alloy mixed sufficiently with Ti substrate. Moreover, there is no obvious boundary between the alloyed layer and substrate.

Corrosion Resistance of AZ91 Mg Alloy Modified by High-Current Pulsed Electron Beam

The high-current pulsed electron beam(HCPEB) treatment with current density 6 J/cm^2 was applied on AZ91 Mg alloy to improve its corrosion resistance. Results showed that the net-like Mg_(17)Al_(12) disappeared on the surface of AZ91 Mg alloy after irradiation by HCPEB, which was instead of supersaturated Al element on the surface. Nevertheless, the application of HCPEB also led to the formation of crater-like and groove-like structures as well as micro-cracks on the surface of AZ91 Mg alloy. After HCPEB treatment by 3, 5 and 10 pulses, the AZ91 Mg alloy exhibited better corrosion resistance.However, the increasing amount of micro-cracks reduced the anti-corrosive properties of AZ91 Mg alloy as the pulse increased to 20 and 30.

Deformation mechanism and microstructures on polycrystalline aluminum induced by high-current pulsed electron beam

In this paper, we present an experimental investigation of deformation twinning in polycrystalline aluminum exposed to high-current pulsed electron beam (HCPEB) irradiation. The residual tensile stress with about 10 2 MPa was introduced in the irradiated surface layer. The feature characteristic irradiated with various numbers of pulses was investigated. The formation of a large number of twin bands on the surface irradiated with multiple pulses was determined. The experimental observations indicated that the deformation twinning was indeed triggered during HCPEB irradiation. It is suggested that high value of stress and strain rate induced by rapid heating and cooling due to HCPEB irradiation may cause the shifting of whole atomic planes simultaneously. Additionally, some slipping systems may be suppressed due to the geometric confinement by thinned size of surface layer, which can promote the initiation of deformation twinning.

HCPEB表面改性对镀铝CoCrAlY涂层显微组织及氧化性能的影响

利用大气等离子喷涂技术在镍基高温合金基体上制备CoCrAlY涂层,使用EBVD技术蒸镀纯铝薄膜,并利用强流脉冲电子束改性镀铝涂层,通过改变轰击次数以达到改变入射能量的目的。将轰击后的镀铝涂层进行高温氧化实验,观察并分析轰击后镀铝涂层的氧化行为以及显微形貌的变化,研究HCPEB脉冲次数对涂层表面相成分的影响。与APS喷涂涂层相比,改性涂层的氧化动力学曲线更趋近于抛物线,且在氧化后期增重缓慢。XRD结果显示,经不同次数轰击后的涂层相成分基本一致,累计脉冲次数越多,α-Al2O3含量越高。SEM结果显示,经HCPEB轰击后的涂层的表面重熔,形成细胞状凸起结构。经30次轰击后的改性涂层表面氧化0.5h后,出现氧化铝和Co/Cr-O类氧化物;氧化20h后生成横向连续致密的α-Al2O3膜;氧化100h后,在小范围内生成尖晶石类氧化物,α-Al2O3膜仍起保护作用。

Blue photoluminescence from nanocrystalline porous silicon structure fabricated by high-current pulsed electron beam irradiation

N-type Si(111) wafers have been processed by high-current pulsed electron beam(HCPEB) treatment with an increasing number of irradiation(1, 10 and 20pulses). The results of this work show that a highly porous nanostructure was formed after irradiation. Moreover, the high-density Si nanocrystals(Si-ncs) about 3 nm were distributed on the surface of Si wafers and exhibited3.02 e V Photoluminescence(PL) emission in blue band.The PL intensity increases with the increase in the Si-ncs' density in accordance with the quantum confinement model, which can be ascribed to the different pulse time of HCPEB treatment. The possible formation mechanisms of micropores and Si-ncs are discussed.

HCPEB作用下镀铝CoCrAlY涂层的高温氧化行为

使用大气等离子喷涂在镍基高温合金表面制备Co Cr Al Y粘结层并蒸镀一定厚度的纳米铝膜,利用强流脉冲电子束辐照镀铝涂层表面.采用高温氧化试验,观察并分析涂层的高温氧化行为.XRD结果表明,强流脉冲电子束辐照镀铝涂层表层快速氧化生成大量Al_2O_3;100 h氧化后,表层氧化物成分较为稳定,基本保持Al_2O_3较多.尖晶石类氧化物较少的状态.表面形貌分析结果表明,经过强流脉冲电子束辐照镀铝涂层在高温环境下能够保持表层的致密和完整,缺陷很少.涂层表层含有大量均匀且较为致密的Al_2O_3能够有效抵御外界环境的进一步氧化,有较好的的抗高温氧化性能.