Experimental investigation on using CO_(2)/H_(2)O emulsion with high water cut in enhanced oil recovery

CO_(2) emulsions used for EOR have received a lot of interest because of its good performance on CO_(2)mobility reduction.However,most of them have been focusing on the high quality CO_(2) emulsion(high CO_(2) fraction),while CO_(2) emulsion with high water cut has been rarely researched.In this paper,we carried out a comprehensive experimental study of using high water cut CO_(2)/H_(2)O emulsion for enhancing oil recovery.Firstly,a nonionic surfactant,alkyl glycosides(APG),was selected to stabilize CO_(2)/H_(2)O emulsion,and the corresponding morphology and stability were evaluated with a transparent PVT cell.Subsequently,plugging capacity and apparent viscosity of CO_(2)/H_(2)O emulsion were measured systematically by a sand pack displacement apparatus connected with a 1.95-m long capillary tube.Furthermore,a high water cut(40 vol%) CO_(2)/H_(2)O emulsion was selected for flooding experiments in a long sand pack and a core sample,and the oil recovery,the rate of oil recovery,and the pressure gradients were analyzed.The results indicated that APG had a good performance on emulsifying and stabilizing CO_(2) emulsion.An inversion from H_(2)O/CO_(2) emulsion to CO_(2)/H_(2)O emulsion with the increase in water cut was confirmed.CO_(2)/H_(2)O emulsions with lower water cuts presented higher apparent viscosity,while the optimal plugging capacity of CO_(2)/H_(2)O emulsion occurred at a certain water cut.Eventually,the displacement using CO_(2)/H_(2)O emulsion provided 18.98% and 13.36% additional oil recovery than that using pure CO_(2) in long sand pack and core tests,respectively.This work may provide guidelines for EOR using CO_(2) emulsions with high water cut.

Optimization of Injection Parameters for Profile Control and Flooding in an Oilfield during High Water Cut Period

In order to improve the effect of water control and oil stabilization during high water cut period, a mathematical model of five point method well group was established with the high water cut well group of an Oilfield as the target area, the variation law of water cut and recovery factor of different injection parameters was analyzed, and the optimization research of injection parameters of polymer enhanced foam flooding was carried out. The results show that the higher the injection rate, the lower the water content curve, and the higher the oil recovery rate. As the foam defoamed when encountering oil, when the injection time was earlier than 80% of water cut, the later the injection time was, the better the oil displacement effect would be. When the injection time was later than 80% of water cut, the later the injection time was, the worse the oil displacement effect would be. The larger the injection volume, the lower the water content curve and the higher the recovery rate. After the injection volume exceeded 0.2 PV, the amplitude of changes in water content and recovery rate slowed down. The optimal injection parameters of profile control agent for high water content well group in Oilfield A were: injection rate of 15 m3/d, injection timing of 80% water content, and injection volume of 0.2 PV.

Ultrasonic method for measuring water holdup of low velocity and high-water-cut oil-water two-phase flow

Oil reservoirs with low permeability and porosity that are in the middle and late exploitation periods in China＇s onshore oil fields are mostly in the high-water-cut production stage.This stage is associated with severely non-uniform local-velocity flow profiles and dispersed-phase concentration（of oil droplets） in oil-water two-phase flow,which makes it difficult to measure water holdup in oil wells.In this study,we use an ultrasonic method based on a transmission-type sensor in oil-water two-phase flow to measure water holdup in lowvelocity and high water-cut conditions.First,we optimize the excitation frequency of the ultrasonic sensor by calculating the sensitivity of the ultrasonic field using the finite element method for multiphysics coupling.Then we calculate the change trend of sound pressure level attenuation ratio with the increase in oil holdup to verify the feasibility of the employed diameter for the ultrasonic sensor.Based on the results,we then investigate the effects of oildroplet diameter and distribution on the ultrasonic field.To further understand the measurement characteristics of the ultrasonic sensor,we perform a flow loop test on vertical upward oilwater two-phase flow and measure the responses of the optimized ultrasonic sensor.The results show that the ultrasonic sensor yields poor resolution for a dispersed oil slug in water flow（D OS/W flow）,but the resolution is favorable for dispersed oil in water flow（D O/W flow） and very fine dispersed oil in water flow（VFD O/W flow）.This research demonstrates the potential application of a pulsed-transmission ultrasonic method for measuring the fraction of individual components in oil-water two-phase flow with a low mixture velocity and high water cut.

Comprehensive Determination of Reinforcement Parameters for High Cut Slope Based on Intelligent Optimization and Numerical Analysis

High cut slopes have been widely formed due to excavation activities during the period of immigrant relocation in the reservoir area of the Three Gorges, China. Effective reinforcement meas-ures must be taken to guarantee the stability of the slopes and the safety of residents. This article pre-sents a comprehensive method for integrating particle swarm optimization （PSO） and support vector machines （SVMs）, combined with numerical analysis, to handle the determination of appropriate rein-forcement parameters, which guarantee both slope stability and lower construction costs. The relation-ship between reinforcement parameters and slope factor of safety （FOS） and construction costs is in-vestigated by numerical analysis and SVMs, PSO is adopted to determine the best SVM performance resulting in the lowest construction costs for a given FOS. This methodology is demonstrated by a prac-tical reservoir high cut slope stabilised with anti-sliding piles, which is located at the Xingshan （兴山） County of Hubei （湖北） Province, China. The determination process of reinforcement parameters is discussed profoundly, and the pile spacing, length, and section dimension are obtained. The results pro-vide a satisfactory reinforcement design, making it possible a signficant reduction in construction costs.

High speed cutting of AZ31 magnesium alloy

Using LBR-370 numerical control lathe,high speed cutting was applied to AZ31 magnesium alloy.The influence of cutting parameters on microstructure,surface roughness and machining hardening were investigated by using the methods of single factor and orthogonal experiment.The results show that the cutting parameters have an important effect on microstructure,surface roughness and machine hardening.The depth of stress layer,roughness and hardening present a declining tendency with the increase of the cutting speed and also increase with the augment of the cutting depth and feed rate.Moreover,we established a prediction model of the roughness,which has an important guidance on actual machining process of magnesium alloy.

Layer regrouping for water-flooded commingled reservoirs at a high water-cut stage

Layer regrouping is to divide all the layers into several sets of production series according to the physical properties and recovery percent of layers at high water-cut stage, which is an important technique to improve oil recovery for high water-cut multilayered reservoirs. Dif- ferent regroup scenarios may lead to different production performances. Based on unstable oil-water flow theory, a multilayer commingled reservoir simulator is established by modifying the production split method. Taking into account the differences of layer properties, including per- meability, oil viscosity, and remaining oil saturation, the pseudo flow resistance contrast is proposed to serve as a characteristic index of layer regrouping for high water-cut multilayered reservoirs. The production indices of multi- layered reservoirs with different pseudo flow resistances are predicted with the established model in which the data are taken from the Shengtuo Oilfield. Simulation results show that the pseudo flow resistance contrast should be less than 4 when the layer regrouping is implemented. The K-means clustering method, which is based on the objec- tive function, is used to automatically carry out the layer regrouping process according to pseudo flow resistances. The research result is applied to the IV-VI sand groups of the second member of the Shahejie Formation in the Shengtuo Oilfield, a favorable development performance is obtained, and the oil recovery is enhanced by 6.08 %.

Wall Sticking of High Water-Cut, Highly Viscous and High Gel-Point Crude Oil Transported at Low Temperatures

Some crude oils with high water cut have the capability to flow below the oil gel point, while the oil particles adhere to the pipe wall in the form of paste, also called "wall sticking". Wall sticking is a serious problem during the pipeline transportation, leading to partial or total blockage of the pipeline and energy wastage. In this paper, a series of laboratory flow loop experiments were conducted to observe the wall sticking characteristics of crude oil with high water cut, high viscosity and high gel point at low transportation temperatures. The effects of shear stress and water cut on the wall sticking rate and occurrence temperature were investigated. Experimental results indicated that the wall sticking rate and occurrence temperature were lower under stronger shear stress and higher water cut conditions. A criterion of wall sticking occurrence temperature(WSOT) and a regression model of wall sticking rate were then established. Finally, the software was developed to calculate the pressure drop along the pipelines of crude oils with high water-cut. It was able to predict the wall sticking thickness of gelled oil and then calculate the pressure drop along the pipelines. A typical case study indicated that the prediction results obtained from the software were in agreement with actual measured values.

High Speed Cutting Inconel 718 with Coated Carbide and Ceramic Inserts

High speed machining (HSM) technology is one of important aspects of advanced manufacturing technology. Nickel-based superalloys have been widely used in the aircraft and nuclear industry due to their exceptional thermal resistance and the ability to retain mechanical properties at elevated temperatures of service environment over 700 ℃. However, they are classified as difficult-to-cut materials due to their high shear strength, work hardening tendency, highly abrasive carbide particles in the microstructure, strong tendency to weld and form built-up edge and low thermal conductivity. They have a tendency to maintain their strength at high temperature that is generated during machining. The Inconel 718 workpiece material used in the experiment was in the hot forged and annealed condition. The commercially available inserts (all inserts were made by Kennametal Inc.) were selected for the tests, a PVD TiAlN coated carbide, a CVD/PVD TiN/TiCN/TiN coated carbide and a CVD Al 2O 3/TiC/TiCN coated carbide were used at the cutting speed range about 50～100 m/min. Three kinds Sialon grade inserts with various geometry and cutting angles were used at the cutting speed range from 100 m/min to 300 m/min. For evaluating the inserts machinability when high speed cutting Inconel 718, Taylor Formula within certain cutting speeds, an high speed cutting experiment of tool life was carried out to establish the models of tool life by means of rapid facing turning test. The conclusions drawn from the turning of Inconel 718 with silicon nitride based ceramic; PVD and CVD coated carbide inserts are as follows: Studies on tool wear in high speed machining. The thorough investigations and studies were made on the tool wear form, wear process and wear mechanism in high speed cutting of difficult-to-machine materials with ceramic tools and with coated carbides. The major wear mechanisms of nickel-based alloys are interactions of abrasive wear, adhesion wear, micro-breakout and chipping. Optimization analysis on the application of high speed machining. Based on the experimental results, the optimal cutting parameters were determined for machining of Inconel 718 at high speed. The recommendation of tool inserts for high speed cutting inconel 718 were ceramic inserts of KY2000 with negative rake angle and KY2100 with round type, the PVD coated carbide insert KC7310 was recommended for its lower price.

CUTTING REGULARITY AND DISCHARGE CHARACTERISTICS BY USING COMPOSITE COOLING LIQUID IN WIRE CUT ELECTRICAL DISCHARGE MACHINE WITH HIGH WIRE TRAVELING SPEED

The analysis of cutting regularity is provided through using and comparing two typical cooling liquids. It is proved that cutting regularity is greatly affected by cooling liquid＇s washing ability. Discharge characteristics and theoretic analysis between two electrodes are also discussed based on discharge waveform. By using composite cooling liquid which has strong washing ability, the efficiency in the first stable cutting phase has reached more than 200 mm^2/min, and the roughness of the surface has reached Ra〈0.8 μm after the fourth cutting with more than 50 mm^2/min average cutting efficiency. It is pointed out that cutting situation of the wire cut electrical discharge machine with high wire traveling speed （HSWEDM） is better than the wire cut electrical discharge machine with low wire traveling speed （LSWEDM） in the condition of improving the cooling liquid washing ability. The machining indices of HSWEDM will be increased remarkably by using the composite cooling liquid.

Application of New Water Flooding Characteristic Curve in the High Water-Cut Stage of an Oilfield

The oil production predicted by means of the conventional water-drive characteristic curve is typically affected by large deviations with respect to the actual value when the so-called high water-cut stage is entered.In order to solve this problem,a new characteristic relationship between the relative permeability ratio and the average water saturation is proposed.By comparing the outcomes of different matching methods,it is verified that it can well reflect the variation characteristics of the relative permeability ratio curve.Combining the new formula with a reservoir engineering method,two new formulas are derived for the water flooding characteristic curve in the high water-cut stage.Their practicability is verified by using the production data of Mawangmiao and Xijiakou blocks.The results show that the error between the predicted cumulative oil production and production data of the two new water drive characteristic curves is less than the error between the B-type water drive characteristic curve and the other two water drive characteristic curves.It is concluded that the two new characteristic curves can be used to estimate more accurately the recoverable reserves,the final recovery and to estimate the effects of water flooding.

Research on the cutting thermodynamic behavior of high-strength large-thickness offshore jack-up platform leg rack

The cutting of offshore jack-up platform leg rack is highly nonlinear and complex thermal processing process. The residual stress influences the following welding quality and cause crack growth. Therefore, research on the cutting practice of jack-up platform leg rack is significant to improve the safety and reliability of the offshore platform. A heating source model that is applicable to the cutting and emulation of high-strength thick plates han been presented. Then, the thermo-physical characteristic parameters of NV E690 leg plate was calculated by JMATPRO, and is revised according to the theory of metallographic. Furthermore, the numerical simulation of the linear cutting of leg plate was conducted, and the reliability of the heating source model and the thermo-physical characteristic parameters of material were proved by comparing them with the experimental data. Bused on the former study, the optimal parameter （ heating source, cutting speed and radius of the heating source model） which ensured that the gear plate was cut through without edge collapses during cutting was calculated. The optimized process parameters can be used to study the distribution of residual stress in gear plate during cutting which provides theoretical guideline for improving the construction technology of offshore platform legs.

Research on the cutting performance and the wear mechanism of the cermet cutter in high speed turn-milling

When machining D60 steel by high speed turn-milling under the different cooling and lubricating conditions, the cutting performance and the wear mechanism of the cermet cutter are researched. With water soluble cooling fluid, the wear performance of the cermet cutter is bad, and does not adapt to the requirements of machining. However, when machining D60 by high speed turn-milling is under dry conditions, the wearing performance of the cermet cutter is very good and the cutting time lasts almost 3 hours. The wear mechanism of the cermet cutter under the water soluble cooling fluid is different from the dry condition. With the water soluble cooling fluid, a great deal of little chap units are formed since high frequency alternates heat stress. The crash and desquamate of these chap units is the main cause of the cutter wearing. Under dry cutting conditions, it is the main cause of cermet cutter wear in the felting phase intenerating causing rigid phase grains to fall.

Finite element analysis of the end cutting process for U-section parts with high-strength steel

This paper presents a constitutive framework for finite element analysis of the truck beam end cutting process.For this purpose,a finite strain anisotropic elasto-plastic model,which takes nonlinear kinematic and isotropic hardening into account,is presented.Three factors are investigated to determine the effect on cutting quality:radius of cutting tools,strength of materials and relative clearance in cutting.The recommendations made herein are based on the simulation results.

A Method for Calculating Oil Field Relative Permeability Curve by Using Water Drive Characteristic Curve in High Water Cut Stage

With the production of strong bottom water reservoir, it will soon enter the ultra-high water cut stage. After entering the ultra-high water cut period, the main means of stable production is liquid extraction. Large liquid volume has a certain impact on the physical property distribution and fluid seepage law of the oilfield. The relative permeability curve measured according to the industry standard is not used for the prediction of development indicators and the understanding of the dynamic law of the oilfield. In order to understand the characteristics of water drive law in high water cut stage of water drive oilfield, starting from the water drive characteristic curve in high water cut stage, the method for calculating the relative permeability curve is deduced. Through numerical simulation verification and fitting the actual production data, it is confirmed that the obtained relative permeability curve is in line with the reality of the oilfield, It can provide some guiding significance for understanding the production law and water drive law of strong bottom water reservoir in ultra-high water cut stage.

高含水老油田化学驱综合治理新方法及工程实践路径

针对胜利高含水老油田化学驱在科学、技术、管理、工程四个角度面临的开发矛盾,以渤76块为典型单元,在工程实践中进行具体对策分析,构建了“适、专、快、集”的老油田化学驱综合治理新方法。“适”指在老油田科学开发方式转化上,构建不同油藏类型老油田化学驱最佳介入时机模型,提出了在含水率相对较低的阶段,是适合化学驱的有利时机,高效开发方式需“适”介入。“专”指在老油田开发技术应用上,改变传统聚合物先溶解后注入的开发思路,研制可控相转化聚合物,使聚合物先注入后溶解,解决炮眼剪切降解的难题,提高油水流度控制能力,老油田开发矛盾需“专”治理。“快”指在老油田综合管理模式上,改变传统方式,即矿场提问题、研究院设计方案、化工厂生产驱油剂的“串联”管理模式,提出充分发挥矿场、研究院、生产厂三方优势的“并联”管理模式,形成针对单一油藏的产品工业化工艺包以及产业化落地方案,老油田开发技术实现“快”转化。“集”指在老油田工程应用实践上,打破老油田化学驱地面大规模建站的工程工艺模式,采用集约化撬装配注设备,实现老油田化学驱的集约快速配注,老油田工程工艺实现“集”应用。运用上述方法,在胜利油田渤76块综合含水率上升初期,实施由水驱转为可控相转化聚合物驱,实施后一年即见到明显的降水增油效果,单井日产油水平增加8.6t/d,综合含水率降低3.1%,验证了综合治理模式的可行性,为高含水老油田化学驱高效开发提供了有效路径。

Wear Patterns and Mechanisms of Cutting Tools in High Speed Face Milling

High speed machining has received an important interest because it leads to an increase of productivity and a better workpiece surface quality. However, at high cutting speeds, the tool wear increases dramatically due to the high temperature at the tool-workpiece interface. Tool wear impairs the surface finish and hence the tool life is reduced. That is why an important objective of metal cutting research has been the assessment of tool wear patterns and mechanisms. In this paper, wear performances of PCBN tool, ceramic tool, coated carbide tool and fine-grained carbide tool in high speed face milling were presented when cutting cast iron, 45# tempered carbon steel and 45# hardened carbon steel. Tool wear patterns were examined through a tool-making microscope. The research results showed that tool wear types differed in various matching of materials between cutting tool and workpiece. The dominant wear patterns observed were rake face wear, flank wear, chipping, fracture and breakage. The main wear mechanisms were mechanical friction, adhesion, diffusion and chemical wear promoted by cutting forces and high cutting temperature. Hence, the important considerations of high speed cutting tool materials are high heat-resistance and wear-resistance, chemical stability as well as resistance to failure of coatings. The research results will be great benefit to the design and the selection of tool materials and control of tool wear in high-speed machining processes.

基于投影寻踪模型的特高含水油藏剩余油可采潜力评价方法

影响特高含水油藏剩余油可采潜力的因素极其复杂,且各因素的影响程度差异明显,常规方法多以剩余油饱和度或剩余油储量丰度等单一指标评价剩余油潜力,难以有效指导特高含水油藏剩余油挖潜。在充分考虑特高含水油藏剩余油可采潜力影响因素的基础上,综合表征储层非均质性、剩余油可采储量规模、水淹状况以及油水分流能力的差异,构建了特高含水油藏剩余油可采潜力量化评价指标体系,并考虑不同指标对剩余油可采潜力控制程度的差异,将加速遗传算法与投影寻踪模型相结合来确定各评价指标的客观权重,从而构建了剩余油可采潜力指数,形成特高含水油藏剩余油可采潜力量化评价新方法。以渤海Q油田南区主力产层NmIL砂体为例,开展特高含水油藏剩余油可采潜力量化评价,结果表明,新方法可综合表征不同区域位置的储层物性、可采储量丰度和油水分流能力对剩余油可采潜力的影响,实现了主力产层NmIL砂体剩余油可采潜力分布的差异化定量评价,优势可采潜力区域刻画明显,将其作为NmIL砂体下一步井网加密调整潜力区域,以精准指导加密水平井的部署,为特高含水油藏剩余油挖潜提供了一种全新的分析方法与思路。

Theoretical Studies on the SAW Properties of LGS at High-Temperature in Optimal Cuts

Surface acoustic wave (SAW) devices play a significant role in signal processing, frequency control and sensing applications. In general, they cannot operate at elevated temperature. The new crystal of langasite provides possibility for surface acoustic wave devices applied at high temperature. This paper studies the SAW properties of single and doubly rotated cuts of LGS at high temperature. The calculated SAW properties of LGS are analyzed in space with aid of contour plots, and two promising SAW orientation regions at high temperature are presented. For some typical cuts and propagating directions within the two optimal regions, their SAW characteristics vs temperature are discussed. Based on the experimental evidence in some literatures, the reliability of calculated results is verified.

大庆油田特高含水期原油开发规划技术发展现状与展望

开发规划在油田开采过程中发挥着重要的龙头指导作用,是油田企业在一定时期内制定的行动纲领和指南。开发规划技术水平的高低直接影响油田开发的效果和效益。在明确开发规划的基本内涵及与计划、战略的区别基础上,着重介绍了大庆油田发展的2类7项开发规划系列技术,包括开发规律及指标预测技术、技术经济政策界限确定技术、开发效果及潜力评价技术、规划编制及优化技术4项核心技术和可采储量及SEC储量评估技术、经济效益评价及决策支持技术、规划信息化技术3项支撑技术。通过分析当前油田开发规划技术发展存在的生产与技术难题,明确了3个发展方向以及3条实现路径。研究成果与认识对油田开发规划理论研究和实际应用具有重要的参考价值和借鉴意义。

高含水油井关停后剩余油再富集速度研究

高含水断块油藏开发末期构造高部位油井在关井一段时间后,会产生剩余油再富集现象。目前关于剩余油再富集速度的研究中,对剩余油运移过程的影响因素考虑不够全面,影响计算精度。针对该问题,在对运移中剩余油再富集受力分析的基础上建立小油滴状和柱状剩余油再富集速度模型,通过正交试验确立2种剩余油再富集速度的主要敏感因素,并建立了2种剩余油再富集速度及再富集时间图版。研究结果表明:存在驱替压差时,储层渗透率为影响2种剩余油再富集速度的主控因素;当储层渗透率一定,驱替压差的增大和原油黏度的减小有利于2种剩余油再富集速度的增大;同一注采井距位置处的小油滴距离孔隙中滞留柱状剩余油越近,聚集过程中剩余油再富集时间越长,但数值上增加不多。该研究对高含水油藏剩余油再富集潜力区评价具有借鉴意义。