Investigation of passivation effects in AlGaN/GaN metal-insulator-semiconductor high electron-mobility transistor by gate-drain conductance dispersion study

This paper studies the drain current collapse of A1GaN/GaN metal insulator-semiconductor high electron-mobility transistors （MIS-HEMTs） with NbA10 dielectric by applying dual-pulsed stress to the gate and drain of the device. For NbA10 MIS-HEMT, smaller current collapse is found thorough study of the gate-drain conductance dispersion especially when the gate static voltage is -8 V. Through a it is found that the growth of NbA10 can reduce the trap density of the AlGaN surface. Therefore, fewer traps can be filled by gate electrons, and hence the depletion effect in the channel is suppressed effectively. It is proved that the NbAIO gate dielectric can not only decrease gate leakage current but also passivate the A1GaN surface effectively, and weaken the current collapse effect accordingly.

Trap states induced by reactive ion etching in AlGaN/GaN high-electron-mobility transistors

Frequency-dependent conductance measurements were carried out to investigate the trap states induced by reactive ion etching in A1GaN/GaN high-electron-mobility transistors （HEMTs） quantitatively. For the non-recessed HEMT, the trap state density decreases from 2.48 × 1013 cm-2.eV-1 at an energy of 0.29 eV to 2.79 × 1012 cm-2.eV-1 at ET = 0.33 eV. In contrast, the trap state density of 2.38 × 1013-1.10× 1014 cm-2.eV-1 is located at ET in a range of 0.30-0.33 eV for the recessed HEMT. Thus, lots of trap states with shallow energy levels are induced by the gate recess etching. The induced shallow trap states can be changed into deep trap states by 350 ℃ annealing process. As a result, there are two different types of trap sates, fast and slow, in the annealed HEMT. The parameters of the annealed HEMT are ET = 0.29-0.31 eV and DT = 8.16× 1012-5.58 × 1013 cm-2.eV-1 for the fast trap states, and ET = 0.37-0.45 eV and DT = 1.84×1013- 8.50 × 1013 cm-2.eV-1 for the slow trap states. The gate leakage currents are changed by the etching and following annealing process, and this change can be explained by the analysis of the trap states.

Influence of ^(60)Co gamma radiation on fluorine plasma treated enhancement-mode high-electron-mobility transistor

A1GaN/GaN depletion-mode high-electron-mobility transistor （D-HEMT） and fluorine （F） plasma treated enhancement-mode high-electron-mobility transistor （E-HEMT） are exposed to 60Co gamma radiation with a dose of 1.6 Mrad （Si）. No degradation is observed in the performance of D-HEMT. However, the maximum transeonductance of E-HEMT is increased after radiation. The 2DEG density and the mobility are calculated from the results of capacitance-voltage measurement. The electron mobility decreases after fluorine plasma treatment and recovers after radiation. Conductance measurements in a frequency range from 10 kHz to 1 MHz are used to characterize the trapping effects in the devices. A new type of trap is observed in the F plasma treated E-HEMT compared with the D-HEMT, but the density of the trap decreases by radiation. Fitting of Gp/w data yields the trap densities DT = （1-3）Х1012 cm^-2.eV^-1 and DT = （0,2-0.8）Х10^12 cm^2-eV^-1 before and after radiation, respectively. The time constant is 0.5 ms-6 ms. With F plasma treatment, the trap is introduced by etch damage and degrades the electronic mobility. After 60Co gamma radiation, the etch damage decreases and the electron mobility is improved. The gamma radiation can recover the etch damage caused by F plasma treatment.

Robust Performance of AlGaN-Channel Metal-Insulator-Semiconductor High-Electron-Mobility Transistors at High Temperatures

Superior characteristics of Al Ga N-channel metal-insulator-semiconductor（MIS） high electron mobility transistors（HEMTs） at high temperatures are demonstrated in detail. The temperature coefficient of the maximum saturation drain current for the Al GaN-channel MIS HEMT can be reduced by 50% compared with the Ga N-channel HEMT. Moreover, benefiting from the better suppression of gate current and reduced leakage current in the buffer layer, the Al Ga N-channel MIS HEMT demonstrates an average breakdown electric field of 1.83 MV/cm at25℃ and 1.06 MV/cm at 300℃, which is almost 2 times and 3 times respectively larger than that of the reference Ga N-channel HEMT. Pulsed mode analyses suggest that the proposed device suffers from smaller current collapse when the temperature reaches as high as 300℃.

AlGaN/GaN high-electron-mobility transistors with transparent gates by Al-doped ZnO

AlGaN/GaN high-electron-mobility transistors （HEMTs） with Al-doped ZnO （AZO） transparent gate electrodes are fabricated, and Ni/Au/Ni-gated HEMTs are produced in comparison. The AZO-gated HEMTs show good DC characteristics and Schottky rectifying characteristics, and the gate electrodes achieve excellent transparencies. Compared with Ni/Au/Ni-gated HEMTs, AZO-gated HEMTs show a low saturation current, high threshold voltage, high Schottky barrier height, and low gate reverse leakage current. Due to the higher gate resistivity, AZO-gated HEMTs exhibit a current-gain cutoff frequency （fT） of 10 GHz and a power gain cutoff frequency （fmax） of 5 GHz, and lower maximum oscillation frequency than Ni/Au/Ni-gated HEMTs. Moreover, the C-V characteristics are measured and the gate interface characteristics of the AZO-gated devices are investigated by a C-V dual sweep.

Investigation of trap states in Al_2O_3 InAlN/GaN metal–oxide–semiconductor high-electron-mobility transistors

In this paper the trapping effects in Al2O3/In0.17Al0.83N/GaN MOS-HEMT（here, HEMT stands for high electron mobility transistor） are investigated by frequency-dependent capacitance and conductance analysis. The trap states are found at both the Al2O3/In AlN and InAlN/GaN interface. Trap states in InAlN/GaN heterostructure are determined to have mixed de-trapping mechanisms, emission, and tunneling. Part of the electrons captured in the trap states are likely to tunnel into the two-dimensional electron gas（2DEG） channel under serious band bending and stronger electric field peak caused by high Al content in the In AlN barrier, which explains the opposite voltage dependence of time constant and relation between the time constant and energy of the trap states.

Fabrication and characterization of V-gate AlGaN/GaN high-electron-mobility transistors

V-gate GaN high-electron-mobility transistors （HEMTs） are fabricated and investigated systematically. A V-shaped recess geometry is obtained using an improved Si3N4 recess etching technology. Compared with standard HEMTs, the fabricated V-gate HEMTs exhibit a 17% higher peak extrinsic transconductance due to a narrowed gate foot. Moreover, both the gate leakage and current dispersion are dramatically suppressed simultaneously, although a slight degradation of frequency response is observed. Based on a two-dimensional electric field simulation using Silvaco ＂ATLAS＂ for both standard HEMTs and V-gate HEMTs, the relaxation in peak electric field at the gate edge is identified as the predominant factor leading to the superior performance of V-gate HEMTs.

Effect of gate length on breakdown voltage in AlGaN/GaN high-electron-mobility transistor

The effects of gate length L_G on breakdown voltage VBRare investigated in AlGaN/GaN high-electron-mobility transistors（HEMTs） with L_G= 1 μm^20 μm. With the increase of L_G, VBRis first increased, and then saturated at LG= 3 μm. For the HEMT with L_G= 1 μm, breakdown voltage VBRis 117 V, and it can be enhanced to 148 V for the HEMT with L-_G= 3 μm. The gate length of 3 μm can alleviate the buffer-leakage-induced impact ionization compared with the gate length of 1 μm, and the suppression of the impact ionization is the reason for improving the breakdown voltage.A similar suppression of the impact ionization exists in the HEMTs with LG〉 3 μm. As a result, there is no obvious difference in breakdown voltage among the HEMTs with LG= 3 μm^20 μm, and their breakdown voltages are in a range of 140 V–156 V.

The effects of ^(60)Co γ-ray irradiation on the DC characteristics of enhancement-mode AlGaN/GaN high-electron-mobility transistors

The effects of ^60Co γ-ray irradiation on the DC characteristics of AlGaN/GaN enhancement-mode high-electron- mobility transistors （E-mode HEMTs） are investigated. The results show that having been irradiated by^60Co γ-rays at a dose of 3 Mrad （Si）, the E-mode HEMT reduces its saturation drain current and maximal transconductance by 6% and 5%, respectively, and significantly increases both forward and reverse gate currents, while its threshold voltage is affected only slightly. The obvious performance degradation of E-mode A1GaN/GaN HEMTs is consistent with the creation of electronegative surface state charges in the source-gate spacer and gate-drain spacer after being irradiated.

Evaluation of thermal resistance constitution for packaged AlGaN/GaN high electron mobility transistors by structure function method

The evaluation of thermal resistance constitution for packaged A1GaN/GaN high electron mobility transistor （HEMT） by structure function method is proposed in this paper. The evaluation is based on the transient heating measurement of the A1GaN/GaN HEMT by pulsed electrical temperature sensitive parameter method. The extracted chip-level and package-level thermal resistances of the packaged multi-finger A1GaN/GaN HEMT with 400μm SiC substrate are 22.5 K/W and 7.2 K/W respectively, which provides a non-invasive method to evaluate the chip-level thermal resistance of packaged A1GaN/GaN HEMTs. It is also experimentally proved that the extraction of the chip- level thermal resistance by this proposed method is not influenced by package form of the tested device and temperature boundary condition of measurement stage.

Enhancement of terahertz coupling efficiency by improved antenna design in GaN/AlGaN high electron mobility transistor detectors

An optimized micro-gated terahertz detector with novel triple resonant antenna is presented.The novel resonant antenna operates at room temperature and shows more than a 700% increase in photocurrent response compared to the conventional bowtie antenna.In finite-difference-time-domain simulations,we found the performance of the self-mixing GaN/AlGaN high electron mobility transistor detector is mainly dependent on the parameters L gs（the gap between the gate and the source/drain antenna） and L w（the gap between the source and drain antenna）.With the improved triple resonant antenna,an optimized micrometer-sized AlGaN/GaN high electron mobility transistor detector can achieve a high responsivity of 9.45×102 V/W at a frequency of 903 GHz at room temperature.

Two-dimensional electron gas characteristics of InP-based high electron mobility transistor terahertz detector

The samples of InxGa（1-x）As/In（0.52）Al（0.48）As two-dimensional electron gas（2DEG）are grown by molecular beam epitaxy（MBE）.In the sample preparation process,the In content and spacer layer thickness are changed and two kinds of methods,i.e.,contrast body doping andδ-doping are used.The samples are analyzed by the Hall measurements at 300 Kand 77 K.The InxGa1-xAs/In0.52Al0.48As 2DEG channel structures with mobilities as high as 10289 cm^2/V·s（300 K）and42040 cm^2/V·s（77 K）are obtained,and the values of carrier concentration（Nc）are 3.465×10^12/cm^2 and 2.502×10^12/cm^2,respectively.The THz response rates of In P-based high electron mobility transistor（HEMT）structures with different gate lengths at 300 K and 77 K temperatures are calculated based on the shallow water wave instability theory.The results provide a reference for the research and preparation of In P-based HEMT THz detectors.

High-electric-field-stress-induced degradation of SiN passivated AlGaN/GaN high electron mobility transistors

AlGaN/GaN high electron mobility transistors （HEMTs） are fabricated by employing SiN passivation, this paper investigates the degradation due to the high-electric-field stress. After the stress, a recoverable degradation has been found, consisting of the decrease of saturation drain current IDsat, maximal transconductance gm, and the positive shift of threshold voltage VTH at high drain-source voltage VDS. The high-electric-field stress degrades the electric characteristics of AlGaN/GaN HEMTs because the high field increases the electron trapping at the surface and in AlGaN barrier layer. The SiN passivation of AlGaN/GaN HEMTs decreases the surface trapping and 2DEC depletion a little during the high-electric-field stress. After the hot carrier stress with VDS = 20 V and VGS= 0 V applied to the device for 104 sec, the SiN passivation decreases the stress-induced degradation of IDsat from 36% to 30%. Both on-state and pulse-state stresses produce comparative decrease of IDsat, which shows that although the passivation is effective in suppressing electron trapping in surface states, it does not protect the device from high-electric-field degradation in nature. So passivation in conjunction with other technological solutions like cap layer, prepassivation surface treatments, or field-plate gate to weaken high-electric-field degradation should be adopted.

Novel model of a AlGaN/GaN high electron mobility transistor based on an artificial neural network

In this paper we present a novel approach to modeling AlGaN/GaN high electron mobility transistor （HEMT） with an artificial neural network （ANN）. The AlGaN/GaN HEMT device structure and its fabrication process are described. The circuit-based Neuro-space mapping （neuro-SM） technique is studied in detail. The EEHEMT model is implemented according to the measurement results of the designed device, which serves as a coarse model. An ANN is proposed to model AIGaN/CaN HEMT based on the coarse model. Its optimization is performed. The simulation results from the model are compared with the measurement results. It is shown that the simulation results obtained from the ANN model of A1GaN/GaN HEMT are more accurate than those obtained from the EEHEMT model.

Influence of a drain field plate on the forward blocking characteristics of an AlGaN/GaN high electron mobility transistor

In this paper, the influence of a drain field plate （FP） on the forward blocking characteristics of an AlGaN/GaN high electron mobility transistor （HEMT） is investigated. The HEMT with only a gate FP is optimized, and breakdown voltage VBR is saturated at 1085 V for gate–drain spacing LGD ≥ 8 μm. On the basis of the HEMT with a gate FP, a drain FP is added with LGD=10 μm. For the length of the drain FP LDF ≤ 2 μm, VBR is almost kept at 1085 V, showing no degradation. When LDF exceeds 2 μm, VBR decreases obviously as LDF increases. Moreover, the larger the LDF, the larger the decrease of VBR. It is concluded that the distance between the gate edge and the drain FP edge should be larger than a certain value to prevent the drain FP from affecting the forward blocking voltage and the value should be equal to the LGD at which VBR begins to saturate in the first structure. The electric field and potential distribution are simulated and analyzed to account for the decrease of VBR.

Effect of defects properties on InP-based high electron mobility transistors

The performance damage mechanism of InP-based high electron mobility transistors(HEMTs) after proton irradiation has been investigated comprehensively through induced defects.The effects of the defect type, defect energy level with respect to conduction band ET, and defect concentration on the transfer and output characteristics of the device are discussed based on hydrodynamic model and Shockley–Read–Hall recombination model.The results indicate that only acceptorlike defects have a significant influence on device operation.Meanwhile, as defect energy level ETshifts away from conduction band, the drain current decreases gradually and finally reaches a saturation value with ETabove 0.5 eV.This can be attributed to the fact that at sufficient deep level, acceptor-type defects could not be ionized any more.Additionally,the drain current and transconductance degrade more severely with larger acceptor concentration.These changes of the electrical characteristics with proton radiation could be accounted for by the electron density reduction in the channel region from induced acceptor-like defects.

High temperature characteristics of AlGaN/GaN high electron mobility transistors

Direct current （DC） and pulsed measurements are performed to determine the degradation mechanisms of A1GaN/GaN high electron mobility transistors （HEMTs） under high temperature. The degradation of the DC characteristics is mainly attributed to the reduction in the density and the mobility of the two-dimensional electron gas （2DEG）. The pulsed measurements indicate that the trap assisted tunneling is the dominant gate leakage mechanism in the temperature range of interest. The traps in the barrier layer become active as the temperature increases, which is conducive to the electron tunneling between the gate and the channel. The enhancement of the tunneling results in the weakening of the current collapse effects, as the electrons trapped by the barrier traps can escape more easily at the higher temperature.

Influence of a two-dimensional electron gas on current-voltage characteristics of Al_(0.3)Ga_(0.7) N/GaN high electron mobility transistors

The J-V characteristics of AltGa1 tN/GaN high electron mobility transistors（HEMTs） are investigated and simulated using the self-consistent solution of the Schro dinger and Poisson equations for a two-dimensional electron gas（2DEG） in a triangular potential well with the Al mole fraction t = 0.3 as an example.Using a simple analytical model,the electronic drift velocity in a 2DEG channel is obtained.It is found that the current density through the 2DEG channel is on the order of 10^13 A/m^2 within a very narrow region（about 5 nm）.For a current density of 7 × 10^13 A/m62 passing through the 2DEG channel with a 2DEG density of above 1.2 × 10^17 m^-2 under a drain voltage Vds = 1.5 V at room temperature,the barrier thickness Lb should be more than 10 nm and the gate bias must be higher than 2 V.

Kink effect in AlGaN/GaN high electron mobility transistors by electrical stress

The kink effect is studied in an AlGaN/GaN high electron mobility transistor by measuring DC performance during fresh, short-term stress and recovery cycle with negligible degradation. Vdg plays an assistant role in detrapping electrons and short-term stress results in no creation of new category traps but an increase in number of active traps. A possible mechanism is proposed that electrical stress supplies traps with the electric field for activation and when device is under test field-assisted hot-electrons result in electrons detrapping from traps, thus deteriorating the kink effect. In addition, experiments show that the impact ionization is at a relatively low level, which is not the dominant mechanism compared with trapping effect. We analyse the complicated link between the kink effect and stress bias through groups of electrical stress states： Pals = 0-state, off-state, on-state （on-state with low voltage, high-power state, high field state）. Finlly, a conclusion is drawn that electric field brings about more severe kink effect than hot electrons. With the assistance of electric field, hot electrons tend to be possible to modulate the charges in deep-level trap.

Neutron irradiation effects on AlGaN/GaN high electron mobility transistors

A1GaN/GaN high electron mobility transistors （HEMTs） were exposed to 1 MeV neutron irradiation at a neutron ftuence of 1 × 10^15 cm-2. The dc characteristics of the devices, such as the drain saturation current and the maximum transconductance, decreased after neutron irradiation. The gate leakage currents increased obviously after neutron irradiation. However, the rf characteristics, such as the cut-off frequency and the maximum frequency, were hardly affected by neutron irradiation. The A1GaN/GaN heterojunctions have been employed for the better understanding of the degradation mechanism. It is shown in the Hall measurements and capacitance voltage tests that the mobility and concentration of two-dimensional electron gas （2DEG） decreased after neutron irradiation. Tbere was no evidence of the full-width at half-maximum of X-ray diffraction （XRD） rocking curve changing after irradiation, so the dislocation was not influenced by neutron irradiation. It is concluded that the point defects induced in A1GaN and GaN by neutron irradiation are the dominant mechanisms responsible for performance degradations of A1GaN/GaN HEMT devices.