Microstructure and Properties of AlCoCrFeNiTi High-Entropy Alloy Coatings Prepared by Laser Cladding

21-4N(5Cr21Mn9Ni4N)is extensively employed in the production of engine valves,operating under severe conditions.Apart from withstanding high-temperature gas corrosion,it must also endure the impact of cylinder explosion pressure.The predominant failure mode of 21-4N valves is abrasive wear.Surface coatings serve as an effective approach to prevent such failures.In this investigation,Laser cladding technology was utilized to fabricate AlCoCrFeNiTi high entropy alloy coatings onto the surfaces of 21-4N valves.According to the findings,the cladding zone has a normal dendritic microstructure,a good substrate-to-cladding layer interaction,and no obvious flaws.In terms of hardness,the cladding demonstrates an average hardness of 620 HV.The hardness has increased by 140%compared to the substrate.The average hardness of the cladding remains at approximately 520 HV even at elevated temperatures.Regarding frictional wear performance,between 400℃and 800℃,the cladding layer exhibits an average friction coefficient of 0.4,with the primary wear mechanisms being abrasive wear,adhesive wear,and a minor degree of plastic deformation.

Effect of Mn element on shock response in CoCrFeNiMnx high entropy alloys

The effect of Mn element on shock response of CoCrFeNiMnx high entropy alloys(HEAs)are investigated using molecular dynamics simulations.Structural analysis shows that Mn-rich CoCrFeNiMnx HEA has a larger average atomic volume.The elastic properties of CoCrFeNiMnx HEAs under various hydrostatic pressures are studied,revealing that the elastic modulus decreases with increasing of Mn content.The shock thermodynamic parameters are quantitatively analyzed.The Mn-dependent shock Hugoniot relationship of CoCrFeNiMnx HEAs is obtained:Us=1.25+(5.21–0.011x)Up.At relatively high shock pressure,the increase in Mn content promotes the formation of clustered BCC structures and hinders the development of dislocations.In addition,more FCC structures in Mn-rich CoCrFeNiMnx HEAs transform into disordered structures during spallation.Spall strength decreases with increasing Mn content.This study can provide a reference for the design and application of CoCrFeNiMn HEAs under shock loading.

A critical review on solid-state welding of high entropy alloys-processing,microstructural characteristics and mechanical properties of joints

The high entropy alloys(HEAs)are the newly developed high-performance materials that have gained significant importance in defence,nuclear and aerospace sector due to their superior mechanical properties,heat resistance,high temperature strength and corrosion resistance.These alloys are manufactured by the equal mixing or larger proportions of five or more alloying elements.HEAs exhibit superior mechanical performance compared to traditional engineering alloys because of the extensive alloying composition and higher entropy of mixing.Solid state welding(SSW)techniques such as friction stir welding(FSW),rotary friction welding(RFW),diffusion bonding(DB)and explosive welding(EW)have been efficiently deployed for improving the microstructural integrity and mechanical properties of welded HEA joints.The HEA interlayers revealed greater potential in supressing the formation of deleterious intermetallic phases and maximizing the mechanical properties of HEAs joints.The similar and dissimilar joining of HEAs has been manifested to be viable for HEA systems which further expands their industrial applications.Thus,the main objective of this review paper is to present a critical review of current state of research,challenges and opportunities and main directions in SSW of HEAs mainly CoCrFeNiMn and Al_xCoCrFeNi alloys.The state of the art of problems,progress and future outlook in SSW of HEAs are critically reviewed by considering the formation of phases,microstructural evolution and mechanical properties of HEAs joints.

Microbiologically influenced corrosion resistance enhancement of coppercontaining high entropy alloy Fe_(x)Cu_(1−x)CoNiCrMn against Pseudomonas aeruginosa

To enhance the microbiologically influenced corrosion(MIC)resistance of FeCoNiCrMn high entropy alloy(HEAs),a series of Fe_(x)Cu_((1−x))CoNiCrMn(x=1,0.75,0.5,and 0.25)HEAs were prepared.Microstructural characteristics,corrosion behavior(morphology observation and electrochemical properties),and antimicrobial performance of Fe_(x)Cu_((1−x))CoNiCrMn HEAs were evaluated in a medium inoculated with typical corrosive microorganism Pseudomonas aeruginosa.The aim was to identify copper-containing FeCoNiCrMn HEAs that balance corrosion resistance and antimicrobial properties.Results revealed that all Fe_(x)Cu_((1−x))CoNiCrMn(x=1,0.75,0.5,and 0.25)HEAs exhibited an FCC(face centered cubic)phase,with significant grain refinement observed in Fe_(0.75)Cu_(0.25)CoNiCrMn HEA.Electrochemical tests indicated that Fe_(0.75)Cu_(0.25)CoNiCrMn HEA demonstrated lower corrosion current density(i_(corr))and pitting potential(E_(pit))compared to other Fe_(x)Cu_((1−x))CoNiCrMn HEAs in P.aeruginosa-inoculated medium,exhibiting superior resistance to MIC.Anti-microbial tests showed that after 14 d of immersion,Fe_(0.75)Cu_(0.25)CoNiCrMn achieved an antibacterial rate of 89.5%,effectively inhibiting the adhesion and biofilm formation of P.aeruginosa,thereby achieving resistance to MIC.

Characterization of local chemical ordering and deformation behavior in high entropy alloys by transmission electron microscopy

Short-range ordering(SRO)is one of the most important structural features of high entropy alloys(HEAs).However,the chemical and structural analyses of SROs are very difficult due to their small size,complexed compositions,and varied locations.Transmission electron microscopy(TEM)as well as its aberration correction techniques are powerful for characterizing SROs in these compositionally complex alloys.In this short communication,we summarized recent progresses regarding characterization of SROs using TEM in the field of HEAs.By using advanced TEM techniques,not only the existence of SROs was confirmed,but also the effect of SROs on the deformation mechanism was clarified.Moreover,the perspective related to application of TEM techniques in HEAs are also discussed.

Spark plasma sintering of tungsten-based WTaVCr refractory high entropy alloys for nuclear fusion applications

W-based WTaVCr refractory high entropy alloys (RHEA) may be novel and promising candidate materials for plasma facing components in the first wall and diverter in fusion reactors. This alloy has been developed by a powder metallurgy process combining mechanical alloying and spark plasma sintering (SPS). The SPSed samples contained two phases, in which the matrix is RHEA with a body-centered cubic structure, while the oxide phase was most likely Ta2VO6through a combined analysis of X-ray diffraction (XRD),energy-dispersive spectroscopy (EDS), and selected area electron diffraction (SAED). The higher oxygen affinity of Ta and V may explain the preferential formation of their oxide phases based on thermodynamic calculations. Electron backscatter diffraction (EBSD) revealed an average grain size of 6.2μm. WTaVCr RHEA showed a peak compressive strength of 2997 MPa at room temperature and much higher micro-and nano-hardness than W and other W-based RHEAs in the literature. Their high Rockwell hardness can be retained to at least 1000°C.

Formation condition of solid solution type high-entropy alloy

Formation condition of high-entropy alloys with solid solution structure was investigated. Seventeen kinds of the high-entropy alloys with different components were prepared, the influencing factors （the comprehensive atomic radius difference δ, the mixing enthalpy AH and the mixing entropy AS） of phase composition of the alloys were calculated, and the microstructure and phase compositions of alloys were analyzed by using SEM and XRD. The result shows that only the systems with δ≤2.77 and △H≥-8.8 kJ/mol will form high entropy alloy with simple solid solution. Otherwise, intermetallic compounds will exist in the alloys. So, selection of the type of element has important effects on microstructure and properties of high entropy alloys.

First principles calculation of intermetallic compounds in FeTiCoNiVCrMnCuAl system high entropy alloy

The structural, electronic and elastic properties of common intermetallic compounds in FeTiCoNiVCrMnCuAI system high entropy alloy were investigated by the first principles calculation. The calculation results of formation enthalpy and cohesive energy show that FeTi, Fe2Ti, AlCrFe2, Co2Ti, AlMn2V and Mn2Ti phases may form in the formation process of the alloy. Further studies show that FeTi, FezTi, AlCrFe2, Co2Ti and AlMn2V phases with higher shear modulus and elastic modulus would be excellent strengthening phases in high entropy alloy and would improve the hardness of the alloy. In addition, the partial density of states was investigated for revealing the bonding mode, and the analyses on the strength of p-d hybridization also reveal the underlying mechanism for the elastic properties of these compounds.

Processing effects on the magnetic and mechanical properties of FeCoNiAl_(0.2)Si_(0.2) high entropy alloy

High entropy alloys with the composition of FeCoNiA10.2Si0.2 were prepared by arc melting and induction melting, denoted by A1 and A2, respectively. The samples prepared by these two techniques have a face-centered cubic （FCC） phase structure and a typical dendrite morphology. The tensile yield strength and maximum strength of A2 samples are about 280 and 632 MPa, respectively. Moreover~ the elongation can reach 41.7%. These two alloys prepared by the different methods possess the similar magnetic properties. The saturation magnetization and coercivity can reach 1.151 T and 1400 A/m for A1 samples and 1.015 T and 1431 A/m for A2 samples, respectively. Phases in A2 samples do not change, which are heat treated at different temperatures, then quenched in water. Only the sample, which is heat treated at 600~C for 3 h and then furnace cooled, has a new phase precipitated. Besides, the coercivity decreases obviously at this temperature. Cold rolling and the subsequent heat treatment cannot improve the magnetic properties effectively. However, cold rolling plays an important role in improving the strength.

Effects of Al and Mo on high temperature oxidation behavior of refractory high entropy alloys

Refractory high entropy alloys have superior mechanical properties at high temperatures, and the oxidation behavior of these alloys is very important. The present work investigated the high temperature oxidation behavior of three alloys with compositions of TiNbTa0.5Zr, TiNbTa0.5ZrAl and TiNbTa0.5ZrAlMo0.5, and the effects of alloying elements were discussed. Results indicated that the oxidation rates of the TiNbTa0.5Zr and TiNbTa0.5ZrAl alloys are controlled by diffusion, and obey the exponential rule. However, the oxidation rate of the TiNbTa0.5ZrAlMo0.5 alloy is controlled by interface reaction, and obeys the linear rule. The addition of Al leads to a better oxidation resistance by forming a protective oxide scale. However, the protection of Al-rich scale is weakened by the addition of Mo. Extensive pores and cracks occur in the oxide scale of the TiNbTa0.5ZrAlMo0.5 alloy, resulting in a significant decrease in oxidation resistance.

Azo dye degradation behavior of AlFeMnTiM(M = Cr, Co, Ni) high-entropy alloys

Because of the potential carcinogenic effects and difficult degradation of azo dyes, their degradation has been a longstanding problem. The degradation of azo dye Direct Blue 6(DB6) using ball-milled(BM) high-entropy alloy(HEA) powders was characterized in this work. Newly designed AlFeMnTiM(M = Cr, Co, Ni) HEAs synthesized by mechanical alloying(MA) showed excellent performance in the degradation of azo dye DB6. The degradation efficiency of AlFeMnTiCr is approximately 19 times greater than that of the widely used commercial Fe–Si–B amorphous alloy ribbons and more than 100 times greater than that of the widely used commercial zero-valent iron(ZVI) powders. The galvanic-cell effect and the unique crystal structure are responsible for the good degradation performance of the BM HEAs. This study indicates that BM HEAs are attractive, valuable, and promising environmental catalysts for wastewater contaminated by azo dyes.

Effect of thermomechanical processing on microstructure and mechanical properties of CoCrFeNiMn high entropy alloy

The CoCrFeNiMn high entropy alloy was produced by homogenization, cold rolling and recrystallization. The effects of thermomechanical processing on microstructures and tensile properties at different temperatures were investigated using X-ray diffractometry（XRD）, optical microscopy（OM）, scanning electron microscopy（SEM） and multi-functional testing machine. The results show that dendritic structures in cast alloy evolve into equiaxed grains after being recrystallized, with single face-centered cubic（FCC） phase detected. The most refined alloys, stemming from the highest rolling ratio（40%）, exhibit the highest strength due to the grain boundary strengthening, while the variation of elongation with temperature shows a concave feature. For the coarse-grained alloys, both the ductility and work hardening ability decrease monotonically with increasing temperature. Serrated flow observed at intermediate temperatures is attributed to the effective pinning of dislocations, which manifests the occurrence of dynamic strain hardening and results in the deterioration in ductility. Besides, dimples on the fracture surfaces indicate the typical ductile rupture mode.

Electrochemical Synthesis and Magnetic Studies of Ni-Fe-Co-Mn-Bi-Tm High Entropy Alloy Film

Amorphous Ni-Fe-Co-Mn-Bi-Tm high entropy alloy films were firstly prepared by potentiostatic electro- deposition. The results indicate that the six elements can be co-deposited in an organic system of DMF （N,N-dimethylformamide）-CH3CN. The surface of the film is composed of compact and uniform particles with triangular cone shape and a particle size of 100-200 nm. A simple face-centered-cubic structure is identified by XRD patterns after the films were annealed under Ar atmosphere. The annealed alloy film shows soft magnetic properties and the magnetization decreases with Fe content decreasing.

Effects of Annealing on Microstructure, Mechanical and Electrical Properties of AlCrCuFeMnTi High Entropy Alloy

The multi-component A1CrCuFeMnTi high entropy alloy was prepared using a vacuum arc melting process. Serial annealing processes were subsequently performed at 590 ℃, 750 ℃, 955 ℃ and 1 100 ℃ respectively with a holding time of 4 h at each temperature. The effects of annealing on microstructure, mechanical and electrical properties of as-cast alloy were investigated by using differential thermal analysis （DTA）, X-ray diffraction （XRD）, scanning electron microscopy （SEM） and transmission electron microscopy （TEM）. The experimental results show that two C14 hexagonal structures remain unchanged after annealing the as-cast A1CrCuFeMnTi alloy specimens being heated to 1 100℃. Both annealed and as-cast microstructures show typical cast-dendrite morphology and similar elemental segregation. The hardness of alloys declines as the annealing temperature increases while the strength of as-cast alloy improves obviously by the annealing treatment. The electrical conductivities of annealed and as-cast alloys are influenced by the distribution of interdendrite re^ions which is rich in Cu element.

Progress in Light-weight High Entropy Alloys

High entropy alloys(HEAs)possess good mechanical properties and a wide range of industrial applications.In this paper,phase formation prediction theory,microstructure,properties and preparation methods of light-weight HEAs(LWHEAs)were reviewed.The problems and challenges faced by LWHEAs development were analyzed.The results showed that many aspects are still weak and require investigation for future advanced alloys,such as clarification of the role of entropy in phase formation and properties of HEAs,improved definition and different generations division of HEAs,close-packed hexagonal(HCP)phase structure prediction and corresponding alloy design and fabrication.Finally,some suggestions were presented in this paper including in-depth research on formation mechanism of multi-component alloy phase and strengthening of large-scale HEA preparation methods via technology compounding and 3D printing technology.Also,there is a need for more research on the in-situ preparation of HEA coatings and films,as well as developing LWHEAs with superior strength and elevated temperature resistance or ultra-low temperature resistance to meet the requirements of future engineering applications.

Effect of nitrogen on microstructure and mechanical properties of Cr Mn Fe VTi6 high entropy alloy

In order to evaluate interstitial strengthening effect on the properties of high entropy alloy(HEA),a nitrogen-doped Cr Mn Fe VTi6 HEA was fabricated by mechanical alloying(MA)and spark plasma sintering(SPS).XRD,SEM,TEM and FIB were used to characterize the phase composition and microstructure of this material.The sintered bulk HEA exhibits a microstructure comprising TiNx,BCC,Laves and B2 phases.The HEA exhibits high yield strength(>2729 MPa)and hardness in lower temperature range of<380℃.Quantitative calculations of the contributions from each strengthening mechanism in the BCC phase indicate that the interstitial strengthening by nitrogen is the dominant mechanism.Nitrogen additions in the BCC phase can produce a yield strength increase of-634 MPa/at.%,which is much higher than the strengthening effects of carbon or boron additions in other alloys.This demonstrates that adding nitrogen is a viable approach for enhancing the strength of HEAs.

Effects of La on microstructure and mechanical properties of NbMoTiVSi0.2 refractory high entropy alloys

To study the effects of La on the microstructure and mechanical properties of refractory high entropy alloys,NbMoTiVSi0.2 alloys with different La contents were prepared.Phase constitution,microstructure evolution,compressive properties and related mechanisms were systematically studied.Results show that the alloys with La addition are composed of BCC solid solution,eutectic structure,MSi2 disilicide phase and La-containing precipitates.Eutectic structure and most of La precipitates are formed at the grain boundaries.Disilicide phase is formed in the grains.La can change the grain morphologies from dendritic structure to near-equiaxed structure,and the average grain size decreases from 180 to 20μm with the increase of La content from 0 to 0.5 at.%.Compressive testing shows that the ultimate strength and the yield strength increase with the increase of La content,which is resulted from the grain boundary strengthening.However,they cannot be greatly improved because of the formation of MSi2 disilicide phase with low strength.The ductility decreases with the increase of La content,which is due to the La precipitates and brittle MSi2 disilicide phase.

Superior corrosion resistance-dependent laser energy density in(CoCrFeNi)95Nb5 high entropy alloy coating fabricated by laser cladding

(CoCrFeNi)95Nb5 high entropy alloy(HEA)coatings were successfully fabricated on a substrate of Q235 steel by laser cladding technology.These(CoCrFeNi)95Nb5 HEA coatings possess excellent properties,particularly corrosion resistance,which is clearly superior to that of some typical bulk HEA and common engineering alloys.In order to obtain appropriate laser cladding preparation process parameters,the effects of laser energy density on the microstructure,microhardness,and corrosion resistance of(CoCrFeNi)95Nb5 HEA coating were closely studied.Results showed that as the laser energy density increases,precipitation of the Laves phase in(CoCrFeNi)95Nb5 HEA coating gradually decreases,and diffusion of the Fe element in the substrate intensifies,affecting the integrity of the(CoCrFeNi)95Nb5 HEA.This decreases the microhardness of(CoCrFeNi)95Nb5 HEA coatings.Moreover,the relative content of Cr2O3,Cr(OH)3,and Nb2O5 in the surface passive film of the coating decreases with increasing energy density,causing corrosion resistance to decrease.This study demonstrates the controllability of a high-performance HEA coating using laser cladding technology,which has significance for the laser cladding preparation of other CoCrFeNi-system HEA coatings.

Microstructure evolution of Al_(0.6)CoCrFeNi high entropy alloy powder prepared by high pressure gas atomization

The influence of cooling rate on the microstructure of Al0.6CoCrFeNi high entropy alloy（HEA） powders was investigated. The spherical HEA powders（D50≈78.65 μm） were prepared by high pressure gas atomization. The different cooling rates were achieved by adjusting the powder diameter. Based on the solidification model, the relationship between the cooling rate and the powder diameter was developed. The FCC phase gradually disappears as particle size decreases. Further analysis reveals that the phase structure gradually changes from FCC＋BCC dual-phase to a single BCC phase with the increase of the cooling rate. The microstructure evolves from planar crystal to equiaxed grain with the cooling rate increasing from 3.19×10^4 to 1.11×10^6 K/s.

Microstructural evolution and corrosion behavior of directionally solidified FeCoNiCrAl high entropy alloy

The FeCoNiCrAl alloys have many potential applications in the fields of structural materials, but few attempts were made to characterize the directional solidification of high entropy alloys. In the present research, the microstructure and corrosion behavior of FeCoNiCrAI high entropy alloy have been investigated under directional solidification. The results show that with increasing solidification rate, the interface morphology of the alloy evolves from planar to cellular and dendritic. The electrochemical experiment results demonstrate that the corrosion products of both non-directionally and directionally solidified FeCoNiCrAI alloys appear as rectangular blocks in phases which Cr and Fe are enriched, while AI and Ni are depleted, suggesting that AI and Ni are dissolved into the NaCl solution. Comparison of the potentiodynamic polarization behaviors between the two differently solidified FeCoNiCrAl high entropy alloys in a 3.5%NaCl solution shows that the corrosion resistance of directionally solidified FeCoNiCrAI alloy is superior to that of the non-directionally solidified FeCoNiCrAI alloy.