As mining delves deeper into the crust, it is necessary to investigate the complex rock responses associated with higher stress gradients. Therefore, it is essential to better understand the mechanisms associated with...As mining delves deeper into the crust, it is necessary to investigate the complex rock responses associated with higher stress gradients. Therefore, it is essential to better understand the mechanisms associated with the rockburst phenomenon. However, due to the large-scale and difficult monitoring of real mining excavations, laboratory scale tests must be utilised to determine the conditions conducive to burst. To this end, this research focuses on the implementation of a new rockburst testing apparatus to replicate the stress conditions of a rock mass excavation at the time of bursting. This apparatus allows the determination of rockburst stresses and a relationship between deviatoric stress and in-situ pressure/depth. Using this relationship it is then possible to estimate the standardised stress levels for a certain rock type which might lead to rockburst occurrence. Furthermore, it is demonstrated that with increasing in-situ pressure, the likelihood(measured as a lower differential stress) and the extent(indicated by the increasing range of deviatoric stress) of rockburst increases. These findings provide valuable information about the conditions necessary for bursting in deep mining.展开更多
A recent research campaign at a Canadian nickel-copper mine involved instrumenting a hard rock sill drift pillar with an array of multi-point rod extensometers,distributed optical fibre strain sensors,and borehole pre...A recent research campaign at a Canadian nickel-copper mine involved instrumenting a hard rock sill drift pillar with an array of multi-point rod extensometers,distributed optical fibre strain sensors,and borehole pressure cells(BHPCs).The instrumentation spanned across a 15.24 m lengthwise segment of the relatively massive granitic pillar situated at a depth of 2.44 km within the mine.Between May 2016 and March 2017,the pillar’s displacement and pressure response were measured and correlated with mining activities on the same level as the pillar,including:(1)mine-by of the pillar,(2)footwall drift development,and(3)ore body stoping operations.Regarding displacements of the pillar,the extensometers provided high temporal resolution(logged hourly)and the optical fibre strain sensors provide high spatial resolution(measured every 0.65 mm along the length of each sensor).The combination of sensing techniques allowed centimetre-scale rock mass bulking near the pillar sidewalls to be distinguished from microstrain-scale fracturing towards the core of the pillar.Additionally,the influence and extent of a mine-scale schistose shear zone transecting the pillar was identified.By converting measured rock mass displacement to velocity,a process was demonstrated which allowed mining activities inducing displacements to be categorised by time-duration and cumulative displacement.In over half of the analysed mining activities,displacements were determined to prolong for over an hour,predominately resulting in submillimetre cumulative displacements,but in some cases multi-centimetre cumulative displacements were observed.This time-dependent behaviour was more pronounced within the vicinity of the plumb shear zone.Displacement measurements were also used to assess selected support member load and elongation mobilisation per mining activity.It was found that a combined static load and elongation capacity of reinforcing members was essential to maintaining excavation stability,while permitting gradual shedding of stress through controlled pillar sidewall displacements.展开更多
The main aspects that require attention in tunnel design in terms of safety and economy are the precise estimation of probable ground conditions and ground behavior during construction. The variation in rock mass beha...The main aspects that require attention in tunnel design in terms of safety and economy are the precise estimation of probable ground conditions and ground behavior during construction. The variation in rock mass behavior due to tunnel excavation sequence plays an important role during the construction stage.The purpose of this research is to numerically evaluate the effect of excavation sequence on the ground behavior for the Lowari tunnel project, Pakistan. For the tunnel stability, the ground behavior observed during the actual partial face excavation sequence is compared with the top heading and bench excavation sequence. For this purpose, the intact rock parameters are used along with the characterization of rock mass joints related parameters to provide input for numerical modelling via FLAC 2D. The in-situ stresses for the numerical modelling are obtained using empirical equations. From the comparison of the two excavation sequences, it was observed that the actual excavation sequence used for Lowari tunnel construction utilized more support than the top heading and bench method. However, the actual excavation sequence provided good results in terms of stability.展开更多
基金the Australian Research Council (No.LP150100539)
文摘As mining delves deeper into the crust, it is necessary to investigate the complex rock responses associated with higher stress gradients. Therefore, it is essential to better understand the mechanisms associated with the rockburst phenomenon. However, due to the large-scale and difficult monitoring of real mining excavations, laboratory scale tests must be utilised to determine the conditions conducive to burst. To this end, this research focuses on the implementation of a new rockburst testing apparatus to replicate the stress conditions of a rock mass excavation at the time of bursting. This apparatus allows the determination of rockburst stresses and a relationship between deviatoric stress and in-situ pressure/depth. Using this relationship it is then possible to estimate the standardised stress levels for a certain rock type which might lead to rockburst occurrence. Furthermore, it is demonstrated that with increasing in-situ pressure, the likelihood(measured as a lower differential stress) and the extent(indicated by the increasing range of deviatoric stress) of rockburst increases. These findings provide valuable information about the conditions necessary for bursting in deep mining.
文摘A recent research campaign at a Canadian nickel-copper mine involved instrumenting a hard rock sill drift pillar with an array of multi-point rod extensometers,distributed optical fibre strain sensors,and borehole pressure cells(BHPCs).The instrumentation spanned across a 15.24 m lengthwise segment of the relatively massive granitic pillar situated at a depth of 2.44 km within the mine.Between May 2016 and March 2017,the pillar’s displacement and pressure response were measured and correlated with mining activities on the same level as the pillar,including:(1)mine-by of the pillar,(2)footwall drift development,and(3)ore body stoping operations.Regarding displacements of the pillar,the extensometers provided high temporal resolution(logged hourly)and the optical fibre strain sensors provide high spatial resolution(measured every 0.65 mm along the length of each sensor).The combination of sensing techniques allowed centimetre-scale rock mass bulking near the pillar sidewalls to be distinguished from microstrain-scale fracturing towards the core of the pillar.Additionally,the influence and extent of a mine-scale schistose shear zone transecting the pillar was identified.By converting measured rock mass displacement to velocity,a process was demonstrated which allowed mining activities inducing displacements to be categorised by time-duration and cumulative displacement.In over half of the analysed mining activities,displacements were determined to prolong for over an hour,predominately resulting in submillimetre cumulative displacements,but in some cases multi-centimetre cumulative displacements were observed.This time-dependent behaviour was more pronounced within the vicinity of the plumb shear zone.Displacement measurements were also used to assess selected support member load and elongation mobilisation per mining activity.It was found that a combined static load and elongation capacity of reinforcing members was essential to maintaining excavation stability,while permitting gradual shedding of stress through controlled pillar sidewall displacements.
基金supported by the National Research Foundation of Korea Grant funded by the Korean Government (NRF-2019R1A2C2003636)
文摘The main aspects that require attention in tunnel design in terms of safety and economy are the precise estimation of probable ground conditions and ground behavior during construction. The variation in rock mass behavior due to tunnel excavation sequence plays an important role during the construction stage.The purpose of this research is to numerically evaluate the effect of excavation sequence on the ground behavior for the Lowari tunnel project, Pakistan. For the tunnel stability, the ground behavior observed during the actual partial face excavation sequence is compared with the top heading and bench excavation sequence. For this purpose, the intact rock parameters are used along with the characterization of rock mass joints related parameters to provide input for numerical modelling via FLAC 2D. The in-situ stresses for the numerical modelling are obtained using empirical equations. From the comparison of the two excavation sequences, it was observed that the actual excavation sequence used for Lowari tunnel construction utilized more support than the top heading and bench method. However, the actual excavation sequence provided good results in terms of stability.
