Spalling characteristics of high-temperature treated granitic rock at different strain rates

The dynamic spalling characteristics of rock are important for stability analysis in rock engineering.This paper presented an experimental investigation on the dynamic spalling characteristics of granite with different temperatures and strain rates.A series of dynamic spalling tests with different impact velocities were conducted on thermally treated granite at different temperatures.The dynamic spalling strengths of granite with different temperatures and strain rates were determined.A model was proposed to correlate the dynamic spalling strength of granite,high temperature and strain rate.The results show that the spalling strength of granite decreases with increasing temperature.Moreover,the spalling strength of granite with a higher strain rate is larger than that with a lower strain rate.The proposed model can describe the relationship among dynamic spalling strength of granite,high temperature and strain rate.

Development of a high-repetition-rate lumped-inductance kicker magnet prototype for the beam switchyard of SHINE

The Shanghai high-repetition-rate X-ray free-electron laser and extreme light facility(SHINE)operates at a maximum repetition rate of 1 MHz.Kicker magnets are key components that distribute electron bunches into three different undulator lines in a bunch-by-bunch mode.The kicker field width must be less than the time interval between bunches.A lumpedinductance kicker prototype was developed using a vacuum chamber with a single-turn coil.The full magnetic field strength was 0.005 T.This paper presents the requirements,design considerations,design parameters,magnetic field calculations,and measurements of the kicker magnets.The relevant experimental results are also presented.The pulse width of the magnetic field was approximately 600 ns,and the maximum operation repetition rate was 1 MHz.The developed kicker satisfies the requirements for the SHINE project.Finally,numerous recommendations for the future optimization of kicker magnets are provided.

Experimental and numerical study on dynamic mechanical behaviors of shale under true triaxial compression at high strain rate

High-energy gas fracturing of shale is a novel,high efficacy and eco-friendly mining technique,which is a typical dynamic perturbing behavior.To effectively extract shale gas,it is important to understand the dynamic mechanical properties of shale.Dynamic experiments on shale subjected to true triaxial compression at different strain rates are first conducted in this research.The dynamic stress-strain curves,peak strain,peak stress and failure modes of shale are investigated.The results of the study indicate that the intermediate principal stress and the minor principal stress have the significant influence on the dynamic mechanical behaviors,although this effect decreases as the strain rate increases.The characteristics of compression-shear failure primarily occur in shale subjected to triaxial compression at high strain rates,which distinguishes it from the fragmentation characteristics observed in shale under dynamic uniaxial compression.Additionally,a numerical three-dimensional Split Hopkinson Pressure Bar(3D-SHPB),which is established by coupling PFC3D and FLAC3D methods,is validated to replicate the laboratory characteristics of shale.The dynamic mechanical characteristics of shale subjected to different confining stresses are systematically investigated by the coupling PFC3D and FLAC3D method.The numerical results are in good agreement with the experimental data.

Flow behavior and microstructure of ZK60 magnesium alloy compressed at high strain rate

Flow behavior and microstructure of a homogenized ZK60 magnesium alloy were investigated during compression in the temperature range of 250-400 ℃ and the strain rate range of 0.1-50 s^-1. The results showed that dynamic recrystallization （DRX） developed mainly at grain boundaries at lower strain rate （0.1-1 s^-1）, while in the case of higher strain rate （10-50 s^-1）, DRX occurred extensively both at twins and grain boundaries at all temperature range, especially at temperature lower than 350 ℃, which resulted in a more homogeneous microstructure than that under other deformation conditions. The DRX extent determines the hot workability of the workpiece, therefore, hot deformation at the strain rate of 10-50 s^-1 and in the temperature range of 250-350 ℃ was desirable for ZK60 alloy. Twin induced DRX during high strain rate compression included three steps. Firstly, twins with high dislocation subdivided the initial grain, then dislocation arrays subdivided the twins into subgrains, and after that DRX took place with a further increase of strain.

HIGH STRAIN RATE SU PERPLASTICITY IN SiCp REINFORCED AZ31 MAGNESIUM MATRIX COMPOSITE

Superplasticity of AZ 31 magnesium matrix composites reinforced with 10 vol% SiC（2 μm） particulate i s investigated at temperature range from 365℃ to 565℃ and strain rate from 2.0 8×10-3 to 5.21×10-1 s-1. The maximum total elongation of 228 % is obtained at a strain rate of 2.08×10-1 s-1. The strain rate se nsitivity exponent （m） higher than 0.3, is observed when the strain rate is high er than 10-1 s-1 at 525℃. Increasing the test temperature to 540℃, the maximum total elongation exceeding 195% is achieved at a higher strain rate of 5.21×10-1 s-1 than that at 525℃. SiC in AZ31/SiCp composite ca n fine the matrix grain size. Filament is observed on the fracture surface of th e specimens showing superplasticity.

Breeding and Utilization of Japonicalinous CMS Line Chunjiang 19A with Wide Compatibility and High Outcrossing Rate

[Objective] To breed and utilize the japonicalinous cytoplasmic male sterile （CMS） line Chunjiang 19A with wide compatibility and high outcrossing rate. [Method] Cbunjiang 16A was used as the female parent to cross with Indica-Japonica crossing material B125, which was used as male parent. Backcross breeding was contin- ued for consecutive generations to breed the CMS lines with wide compatibility and high outcrossing rate. [Result] Chunjiang 19A is a late medium Japonica CMS line with good fertility stability. The proportion of sterile plants and pollen abortion rates are 100% and the Cheng＇s index is 14. It is the japonicalinous CMS line with early flowering, partial stigma exsertion, high outcrossing rate, wide compatibility, high re- sistance to stripe disease and good combining ability. The hybrid rice combinations originated from Chunjiang 19A have strong tUlering ability, dominant heterosis, high resistance to stripe disease, great yield potential and good color change at mature stage. [Conclusion] The successful breeding of Chunjiang 19A laid good foundation for the breeding of Japonica hybrid rice and Indica-Japonica hybrid rice combinations with high seed production and dominant heterosis, showing a promising application prospect.

Effect of Extreme Natural High Temperature on Seed Setting Rate of Rice(Oryza sativa L.) at Heading and Flowering Stage

The seed setting rates of total 198 rice cultivars （lines） at heading and flowering stage were investigated under the condition of extreme natural high tem- perature in 2013 so as to analyze the effect of extreme natural high temperature on seed setting rate of different rice cultivar （line）. The results showed that the contin- uous high temperature showed certain effects on the seed setting rates of tested materials, and significant differences were shown in seed setting rate among differ- ent rice cultivars （lines）. The seed setting rates differed significantly among indica F1 hybrids derived from different sterile and restorer lines, indicating that the sterile and restorer lines had great effects on heat tolerances of different F~ hybrids. The cor- relation analysis showed that the seed setting rates of conventional indica restorer lines and conventional japonica rice cultivars （lines） were negatively related to the daily highest temperature （P〉0.05）, and the seed setting rates of indica F1 hybrids were positively related to the seed setting rates of their restorer lines. Total four in- dica restorer lines, including Ninghuiguangkangzhan, Shuhui 527, Chenghui 3203 and Xianyin-8, and four new japonica rice cultivars （lines）, including Wuyinjinghui （B2）, Nanjing 4//W3660/Nanjing 44 （B12） and Wuyun 2330/JD6011 （B22） were pre- liminarily screened, and their seed setting rates were all close to the normal level （90%）. The screened rice cultivars （lines） showed higher heat tolerances.

Strain rate-dependent high temperature compressive deformation characteristics of ultrafine-grained pure aluminum produced by ECAP

To explore the effect of strain rate ε on the high temperature deformation characteristics of ultrafine-grained materials, the deformation and damage features as well as microstructures of ECAP-treated pure Al at different temperatures T and strain ratesε were systematically studied through compression tests and microscopic observations. The increase in ε eliminates strain softening at T≤473 K, and largely enhances the yield strength and flow stress at 473?573 K. The shear deformation dominates the plastic deformation of ECAP-treated Al. Many cracks along shear bands (SBs) are formed at T≥473 K and secondary SBs basically disappear at 1×10?3 s?1; however, at 1×10?2 s?1, cracks are only observed at temperature below 473 K, and secondary SBs become clearer at T≥473 K. The microstructures of ECAP-treated Al mainly consist of sub-grains (SGs). The increase in ε inhibits the SG growth, thus leading to the increases both in yield strength and flow stress at high temperatures.

Supercritical-hydrothermal accelerated solid state reaction route for synthesis of LiMn_2O_4 cathode material for high-power Li-ion batteries

Synthesis of the spinel structure lithium manganese oxide （LiMn2O4） by supercritical hydrothermal （SH） accelerated solid state reaction （SSR） route was studied. The impacts of the reaction pressure, reaction temperature and reaction time of SH route, and the calcination temperature of SSR route on the purity, particle morphology and electrochemical properties of the prepared LiMn2O4 materials were studied. The experimental results show that after 15 min reaction in SH route at 400 ℃ and 30 MPa, the reaction time of SSR could be significantly decreased, e.g. down to 3 h with the formation temperature of 800 ℃, compared with the conventional solid state reaction method. The prepared LiMn2O4 material exhibits good crystallinity, uniform size distribution and good electrochemical performance, and has an initial specific capacity of 120 mA.h/g at a rate of 0.1C （1C=148 mA/g） and a good rate capability at high rates, even up to 50C.

Study on High Rate Discharge Performance and Mechanism of AB_5 Type Hydrogen Storage Alloys

The effects of surface treatment, particle size distribution,rare earth composition and B additive on the high rate discharge performance of hydrogen storage alloys were investigated. It is found that the activity, discharge capacity and high rate dischargeability of the alloys are improved after physical and chemical modification as a result of the increase of the surface area and formation of the electrocatalysis layers, which increase both the electrochemical reaction rate on the alloy surface and H diffusion rate in the alloy bulk. It is also found that both the over-coarse and over-fine particle size increase the contact resistance of the electrode, resulting in a decrease of discharge capacity, deterioration of high rate dischargeability and lower discharge plateau. In another word, a suitable particle size distribution can enhance the alloy activity, discharge capacity and high rate dischargeability. In addition, the high rate dischargeability is enhanced by increasing La content and decreasing Ce content of the alloy composition because of enlargement of the unit cell volume and the improvement of the surface activity. Moreover, B additive resultes in the formation of the second phase, and makes the alloys easier pulverization, which greatly improves the activity, discharge capacity and high rate dischargeability.

High strain rate superplasticity of rolled AZ91 magnesium alloy

The high strain rate superplastic deformation properties and characteristics of a rolled AZ91 magnesium alloy at temperatures ranging from 623 to 698 K（0.67Tm-0.76Tm） and high strain rates ranging from 10^-3 to 1 s^-1 were investigated.The rolled AZ91 magnesium alloy possesses excellent superplasticity with the maximum elongation of 455% at 623 K and a strain rate of 10-3 s-1,and its strain rate sensitivity m is high up to 0.64.The dominant deformation mechanism responsible for the high strain rate superplasticity is still grain boundary sliding（GBS）,and the dislocation creep mechanism is considered as the main accommodation mechanism.

High strain rate superplasticity of SiC whisker reinforced pure aluminum composites

A β SiC whisker reinforced pure aluminum composites expected to exhibit high strain rate superplasticity has been successfully fabricated by a new processing route consisting of pressure infiltration, extrusion with a low extrusion ratio and rolling. The composites exhibite a total elongation of 220%～380% in the initial strain rates within 1.0×10 -2 ～1.0×10 -1 s -1 and at 893～903 K. According to differential thermal analysis(DTA) and microstructure observation, it is concluded that an appropriately small amount of liquid phase is necessary to cause a good high strain rate superplasticity in aluminum matrix composites in addition to fine and uniform microstructure.

Influences of Stress Wave Propagation upon Studying Dynamic Response of Materials at High Strain Rates

How the wave propagation analysis plays a key role in the studies of dynamic response of materials at high strain rates is analyzed. For the wave propagation technique, the followings are important: the loading and unloading constitutive relation presumed, the positions of the sensors embedded, the interactions between loading waves and unloading waves. For the split Hopkinson pressure bar (SHPB) technique, the assumption of one-dimensional stress wave propagation and the assumption of stress uniformity along the specimen should be satisfied. When the larger diameter bars are employed, the wave dispersion effects should be considered, including the high frequency oscillations, non-uniform stress distribution across the bar section, increase of rise time, and amplitude attenuation. The stress uniformity along the specimen is influenced by the reflection times in specimen, the wave impedance ratio of the specimen and the bar, and the waveform.

ON THE TENSILE MECHANICAL PROPERTY OF Si-Mn TRIP STEELS AT HIGH STRAIN RATE

Tensile mechanical properties of 1.6Si-1.58Mn-0.195C TRIP (transformation-induced plasticity) steels under high strain rate and effects of DP (dual-phase) treatments were studied and compared to the quasi-static tensile behavior. The results show that the increasing of strain rate leads to increasing in their strengths and decreasing in the uniform elongation remarkably. Because the stable retained austenite in TRIP steel can transform to martensite during tensile testing and the material exhibits excellent characteristic of transformation induced plasticity, the plastic deformation behavior is evidently improved and the combination of strength and elongation is superior to that of dual-phase steel, although its strength is smaller than that of DP steel. However, DP treated steel shown lower elongation under dynamic tension in spite of higher strength. A model was proposed to explain the excellent elongation rate of TRIP steel compared with DP steel on the basis of SEM analysis and the strength of the components in microstructure.

Dynamic compressive property and failure behavior of extruded Mg-Gd-Y alloy under high temperatures and high strain rates

For the purpose of investigating the dynamic deformational behavior and failure mechanisms of magnesium under high strain rates,the Split Hopkinson Pressure Bar(SHPB)was used for investigating dynamic mechanical properties of extruded Mg-Gd-Y Magnesium alloy at ambient temperature(300 K),200℃(473 K)and 300℃(573 K)temperature.The samples after compression were analyzed by scanning electron microscope(SEM)and metallographic microscope.Dynamic mechanical properties,crack performance and plastic deformation mechanism of extruded Mg-Gd-Y Magnesium alloy along the extrusion direction(ED)were discussed.The results show that,extruded Mg-Gd-Y Magnesium alloy has the largest dynamic compressive strength which is 535 MPa at ambient temperature(300 K)and strain rate of 2826 s^(−1).When temperature increases,dynamic compressive strength decreases,while ductility increases.The dynamic compression fracture mechanism of extruded Mg-Gd-Y Magnesium alloy is multi-crack propagation and intergranular quasi-cleavage fracture at both ambient temperature and high temperature.The dynamic compressive deformation mechanism of extruded Mg-Gd-Y Magnesium alloy is a combination of twinning,slipping and dynamic recrystallization at both ambient temperature and high temperature.

HIGH STRAIN RATE SUPERPLASTICITY IN A SiC_w/2024Al COMPOSITE MADE BY SQUEEZE CASTING

In this paper,the superplastic characteristics of the beta-SiC whisker reinforced 2024aluminum composite, fabricated by squeeze casting and hot-rolling after extrusion were investigated. The compsite had a fine grain size of about 2μm, and exhibited a strain rate sensitivity of about 0.35 and a maximum elongation of 350% at an initial strain rate of 1.1×10-1s-1 at 803K. In addition, the superplastic deformation mechanisme of the composite were also examined.

Effect of high shear rate on solidification microstructure of semisolid AZ91D alloy

To investigate the effects of rotation speed and shearing time on morphology of semisolid AZ91D alloy,experimental work was undertaken using a twin-screw slurry maker.The results show that increasing the rotation speed and reasonable time can give rise to substantial grain refinement during continuous shearing stage,which can be attributed to the increasing of effective nucleation rate caused by the extremely uniform temperature due to high shear rate and high degree of turbulence.Comparing with low rotation speed at the same thermal condition,the analysis indicates that the microstructures obtained at high rotation speed are homogenous spherical and fine grains instead of dendritic or rosette and exhibits uniform distribution in the eutectic matrix.

Dynamic tensile properties and microstructural evolution of extruded EW75 magnesium alloy at high strain rates

The dynamic tensile properties and microstructural evolution of an extruded EW75 magnesium alloy deformed at ambient temperature and different high strain rates(from 1000 to 3000 s^(-1))along extrusion direction(ED)were investigated by Split Hopkinson Tension Bar(SHTB).The corresponding deformation mechanisms,texture evolution and microstructure changes were analyzed by optical microscope(OM),electron backscatter diffraction(EBSD)and transmission electron microscope(TEM).The results show that the extruded EW75 magnesium alloy along ED exhibits a conventional positive strain rate sensitivity that the dynamic flow stresses increase with in creasing strain rate.Texture measurements show that after dynamic tension,the initial weak texture of extruded EW75 magnesium alloy tansforms to a relatively strong<10-10>//ED texture with increasing strain rates.The microstructural analysis demonstrates that dislocation motion are main deformatin mode to accommodate dynamic tensile deformation at high strain rates.In addition,the interactions of dislocation-dislocation and dislocation-second phase lead to the in crease of flow stress and strain hardening with increasing strain rate.

High-dose-rate intraluminal brachytherapy during preoperative chemoradiation for locally advanced rectal cancers

AIM:To determine the feasibility and safety of high dose rate intraluminal brachytherapy(HDR-ILBT) boost during preoperative chemoradiation for rectal cancer.METHODS:Between 2008 and 2009,thirty-six patients with locally advanced rectal cancer(≥ T3 or N+),were treated initially with concurrent capecitabine(825 mg/m2 oral twice daily) and pelvic external beam radiotherapy(EBRT)(45 Gy in 25 fractions),then were randomized to group A;HDR-ILBT group(n = 17) to receive 5.5-7 Gy×2 to gross tumor volume(GTV) and group B;EBRT group(n = 19) to receive 5.4 Gy×3 fractions to GTV with EBRT.All patients underwent total mesorectal excision.RESULTS:Grade 3 acute toxicities were registered in 12 patients(70.6%) in group A and in 8(42.1%) in group B.Complete pathologic response of T stage(ypT0) in group A was registered in 10 patients(58.8%) and in group B,3 patients(15.8%) had ypT0(P < 0.0001).Sphincter preservation was reported in 6/9 patients(66.7%) in group A and in 5/10 patients(50%) in group B(P < 0.01).Overall radiological response was 68.15% and 66.04% in Group A and B,respectively.During a median follow up of 18 mo,late grade 1 and 2 sequelae were registered in 3 patients(17.6%) and 4 patients(21.1%) in the groups A and B,respectively.CONCLUSION:HDR-ILBT was found to be effective dose escalation technique in preoperative chemoradiation for rectal cancers,with higher response rates,downstaging and with manageable acute toxicities.

Key technologies implementation of high-repetition-rate satellite laser ranging

Satellite laser ranging （SLR） is one of the major space geodetic instruments, which has various applications in earth science. In this paper, we introduce several issues regarding the key technology implementation of high-repetition-rate SLR system. Compared with traditional technology, using kHz and 8ps pulse width laser component, the data quantity and quality of high-repetition-rate satellite laser ranging （SLR） can be significantly improved. The characteristics of high-repetition-rate laser ranging and the key technologies are presented, including the event timer with the precision of picosecond, the generation of range gate signal, and so on. All of them are based on the Field Programmable Gate Arrays （FPGA） and tested on China mobile SLR system-TROS1000. Finally, the observations of satellite Beacon-C are given.