Research on Preparation and Electrochemical Performance of the High Compacted Density Ni-Co-Mn Ternary Cathode Materials

The high compacted density LiNi0.5-xCo0.2Mn0.3MgxO2 cathode material for lithium-ion batteries was synthesized by high temperature solid-state method, taking the Mg element as a doping element and the spherical Ni0.5Co0.2Mn0.3 (OH)2, Li2CO3 as raw materials. The effects of calcination temperature on the structure and properties of the products were investigated. The structure and morphology of cathode materials powder were analyzed by X-ray diffraction spectroscopy (XRD) and scanning electronmicroscopy (SEM). The electrochemical properties of the cathode materials were studied by charge-discharge test and cyclic properties test. The results show that LiNi0.4985Co0.2Mn0.3 Mg0.0015O2 cathode material prepared at calcination temperature 930°C has a good layered structure, and the compacted density of the electrode sheet is above 3.68 g/cm3. The discharge capacity retention rate is more than 97.5% after 100 cycles at a charge-discharge rate of 1C, displaying a good cyclic performance.

Effects of an AMPS-Modified Polyacrylic Acid Superplasticizer on the Performance of Cement-based Materials

A self-made AMPS-modified polyacrylic acid superplasticizer and two others of the same type but with different molecular structures, which are commercially available, are used in this study to investigate the effect of a 2-acrylamide-2-methyl propylene sulfonic （AMPS）-modified polyacrylic acid superplasticizer on the properties of cement-based materials. In the experiments, initial fluidity, 1 and 2 h fluidity over time after admixtion, bleeding rate of the net cement mortar, and adsorption capacity and rate of cement particles are determined by adding different dosages of the three superplasticizers into the cement paste to characterize the dispersivity and the dispersion retention capability of each superplasticizer. Water-reducing rates of three kinds of mortars are simultaneously determined to characterize the water-reducing capacity of each superplasticizer, as well as the 3 and 28 d compressive strengths to characterize the compression resistance. Results show that water-reducing effect and fluidity better maintain the capability of the AMPS-modified polyacrylic acid superplasticizer than the two commercially available polyacrylic acid superplasticizers, and the compressive strengths after 3 and 28 d show significant growth. In conclusion, the effects of water reduction and strengthening of the AMPS-modified polyacrylic acid superplasticizer are evidently better than those of the two commercially available polyacrylic acid superplasticizers.

Toward high-sulfur-content,high-performance lithium-sulfur batteries:Review of materials and technologies

Lithium sulfur batteries(LSBs)are recognized as promising devices for developing next-generation energy storage systems.In addition,they are attractive rechargeable battery systems for replacing lithium-ion batteries(LIBs)for commercial use owing to their higher theoretical energy density and lower cost compared to those of LIBs.However,LSBs are still beset with some persistent issues that prevent them from being used industrially,such as the unavoidable dissolution of lithium polysulfide intermediates during electrochemical reactions and large volume expansion(up to 80%)upon the formation of Li_(2)S,resulting in serious battery life and safety limitations.In the process of solving these problems,it is necessary to maintain a high sulfur content in the cathode materials to ensure that the LSBs have high energy densities and excellent cycle performance.In this review,the novel preparation methods and cathode materials used for preparing LSBs in recent years are reviewed considering the sulfur content and cycle performance.In addition,the problems and difficulties in practically applying cathode materials are described,and the development trend is discussed.

National Joint Engineering Research Center of High Performance Metal Wear Resistant Materials Technology

Founded in 2012,the National Joint Engineering Research Center of High Performance Metal Wear Resistant Materials Technology at Jinan University,one of the'211'key national universities in China,specializes in the research and development of iron based wear resistant materials and their casting technologies to provide support to the production process.The Research Center serves the'Guangdong Province Ceeusro Innovation Platform for Common Technology of High Performance Wear Resistant Materials”,“Guangdong Province Engineering Research Center for Wear Resistant and Special Functional Materials”.

Design of the material performance test apparatus for high temperature gas-cooled reactor

Most materials can be easily corroded or ineffective in carbonaceous atmospheres at high temperatures in the reactor core of the high temperature gas-cooled reactor(HTGR).To solve the problem,a material performance test apparatus was built to provide reliable materials and technical support for relevant experiments of the HTGR.The apparatus uses a center high-purity graphite heater and surrounding thermal insulating layers made of carbon fiber felt to form a strong carbon reducing atmosphere inside the apparatus.Specially designed tungsten rhenium thermocouples which can endure high temperatures in carbonaceous atmospheres are used to control the temperature field.A typical experimental process was analyzed in the paper,which lasted 76 hours including seven stages.Experimental results showed the test apparatus could completely simulate the carbon reduction atmosphere and high temperature environment the same as that confronted in the real reactor and the performance of screened materials had been successfully tested and verified.Test temperature in the apparatus could be elevated up to 1600oC,which covered the whole temperature range of the normal operation and accident condition of HTGR and could fully meet the test requirements of materials used in the reactor.

High Temperature Performances of Spherical Nickel Hydroxide with Additive Y_2O_3

The effect Of Y2O3 as additive to the positive electrode on the high-temperature performances of the Ni-MH batteries was studied. The specific capacities of the positive electrode in Ni-MH battery at higher temperatures are much lower than usual. In order to improve high-temperature performances, charge/discharge curves of the Ni(OH)(2) electrodes with different amounts Of Y2O3 it different temperatures were studied. It is found that the specific capacities of the spherical Ni (OH)(2) with Y2O3 as additive are much higher than those of the regular at higher temperatures. The specific capacity of Ni (OH)(2) containing 1% Y2O3 at 0.2C C/D rate is 35% higher than that of the regular. The specific capacity of Ni (OH)(2) containing 0.2% Y2O3 at 1C C/D rate is 15% higher than that of the regular. Mechanism Of Y2O3 improving high temperature performances of Ni(OH)(2) electrode was also discussed in detail.

RESEARCH ON THE HIGH PERFORMANCE COMPOSITE ROAD CONCRETE

Ordinary concrete presents short service life when used for building and repairing high-grade road with heavy traffic due to its large brittleness, poor bending flexibility and serious shrinkage on drying. In this paper, a new kind of high performance concrete has been designed by means of combination of organic, inorganic material as well as metal material. The research and application have shown that this new concrete can significantly counteract the deficiency of ordinary concrete and give excellent mechanical properties and pavement performances. The application of this new kind of concrete is of great social and economic significance.

Durability of High Performance Color Hardener

The properties of high performance color hardener (HPCH) and the mechanism were studied.HPCH is a composite system, which is composed of cementitious and auxiliary cementing materials, composite additives, abrasion resistance component (aggregate) and pigment. The porosity and pore structure of the material are obviously improved due to the activation, filling and adsorption of auxiliary cementing materials, thus resulting in a great increase of binding capacity for ions in HPCH and the obstacles of ion migrating.The density of material structure, bonding capacity of cementitious material to the abrasion-resisting component and the corrosion resistance are greatly and effectively improved by adding the auxiliary cementing materials and compound additives. According to the tests of dry shrinkage, sulphate resistance, chloride permeability and Ca(OH) 2 content distribution, the property superiority of HPCH is analyzed.The mechanism of materials modification of HPCH is explained from the microscopic point of view by testing the pore structure and pore distribution via the mercury intrusion pressure method.

Preparative Optimization of Cellulose Microspheres Applied as Supports for High-Performance Liquid Chromatography

The aim of this work is optimizing the techniques to prepare pure cellulose microspheres, which are used as packing adsorbents for high-performance liquid chromatography. Thereupon, cellulose was dissolved in a pre-cooled NaOH/urea solution, from which various-size microspheres were prepared. The volume-average diameters were controlled approximately at 30 p,m, 8 ~tm and 4 pm grades when cyclohexane, liquid paraffin and pump oil were used as dispersants, respectively. The present investigations reveal that higher viscosity dispersant is suitable for the preparation of smaller-size microspheres, while larger size microspheres are prepared preferably using lower-viscosity dispersant. The chiral stationary phase derived from 8 μm grade microspheres can separate the enantiomers of efavirenz.

Improved High-rate Performance and Cycling Stability of 1D LiFePO_4 Nanorods by a Facile Annealing Process

To alleviate the main limitations of lithium ion diffusion rate and poor electronic conductivity for LiFePO4 cathode material, it is desirable to synthesize nano-size LiFePO4 material due to its enhanced electronic and lithium ion transport rates and thus an improved high-rate performance. However, our previous synthesized LiFePO4 nanorods only exhibited low high-rate and slightly unstable cycle performance. Possible reasons are the poor crystallization and Fe2＋ oxidation of LiFePO4 nanorods prepared by hydrothermal method. In this paper, LiFePO4 nanorods were simply dealt with at 700 ℃ for 4 h under the protection of Ar and H2 mixture gas. The electrochemical properties of LiFePO4/Li cells were investigated by galvanostatic test and cyclic voltammetry（CV）. The experimental results indicated that the annealed LiFePO4 nanorods delivered an excellent cycling stability and obviously improved capacity of 150 mA·h·g-1 at 1C, and even 122 mA·h·g-1 at 5C.

Numerical Model Research on Rotational Performance of Beam-Column High-Strength Bolt Extension End-Plate Connection Node

The high-strength bolted end plate connection is widely used in the construction industry with its green environmental protection and excellent seismic performance. The joints of the joints are semi-rigid, the force performance is extremely complicated, and the experimental research cost is relatively high, and the cycle is very long. Therefore, the establishment of an efficient numerical model is of great significance for evaluating the force performance of high-strength bolt end plates. In this paper, the influence of different material models on the rotation performance of the joint is studied by numerical simulation, and the bending moment-rotation curve is obtained. The numerical simulation and the experimental results are in good agreement, so as to provide a reference for the design and application of this kind of joint.

Ablation Performance of a Novel Super-hybrid Composite

A novel super-hybrid composite (NSHC) was boron-modified phenolic resin (BPR) with three-dimensional reticulated SiC ceramic (3DRC) and high silica fibers. Ablation performance of the NSHC was studied. The results show that the linear ablation rate of NSHC was lower than that of pure BPR and the high silica/BPR composite. Its linear ablation rate is 1/17 of the high silica/BPR. Mass ablation rate of the NSHC is very close to that of the pure BPR and the high silica/BPR composite. Scanning electron microscope (SEM) analysis indicates that 3DRC has scarcely changed its shape at the ablation temperature. Its special reticulated structure can restrict the materials deformation and prevent high velocity heat flow from eroding the surface of the materials largely and thus increase ablation resistance of the NSHC.

Investigation on Rapidly Solidified T15 High Speed Steel Powder and Its Bulk Microcrystalline Material

Authors produced rapidly solidified T15 high speed steel powders by high pressure(5~ 6MPa) N_a atomization and liquid N_2 cooling,observed and analyzed the morphology and structure of the powders;at the same time,prepared bulk microcrystalline T15 high speed steel materials by hot extruding or HIPing and hot rolling of the powders,observed and measured the microstructure and performance of the bulk materials.It was shown that rapid solidification may change the solidification characteristics and structure of T15 high speed steel powder and improve the qualities and properties of T15 high speed steel materials.

Strengthening Mullite Ceramic Materials by Gas Infiltration

In order to improve the high-temperature performance of mullite ceramic materials,mullite ceramic bodies were placed in closed containers with AlF_(3)·3H_(2)O powder and kept at 1 600 ℃ for 6 h.AlF_(3)·3H_(2)O reacts with O_(2) to produce gaseous compounds AlOF and F,which penetrate into the bodies,promote Al2O3 and SiO_(2) to form mullite whiskers,and strengthen the mullite ceramic materials.The results show that the mullite ceramics have enhanced hot strength,increased bulk density and declined apparent porosity by adding a certain amount of AlF_(3)·3H_(2)O in a closed container.When the addition of AlF_(3)·3H_(2)O is 6%,the bulk density of the ceramic material reaches the maximum and the apparent porosity is the lowest;and when the addition of AlF_(3)·3H_(2)O is 8%,the hot strength of the material is the highest.

4H-SiC基功率器件的high-k栅介质材料研究进展

金属氧化物半导体场效应晶体管(MOSFET)作为碳化硅绝缘栅结构的典型器件被广泛使用,然而SiO_(2)介电常数低的缺点和SiO_(2)/4H-SiC界面特性差的问题一直制约着4H-SiC绝缘栅结构(金属-绝缘体-半导体,MIS)器件更大规模商业化应用,因此科研工作者一直致力于寻找能够替代或弥补SiO_(2)的high-k栅介质材料。本文对该科学问题的研究现状进行综述,首先指出合适的high-k栅介质材料应该拥有较宽的禁带宽度、较高的介电常数、良好的界面特性和热稳定性。然后,主要从栅薄膜制备工艺、沉积温度、栅介质界面特性和电学性能等方面对典型high-k栅介质材料的研究结果进行评价,包括氧化铪(HfO_(2))、氧化铝(Al_(2)O_(3))、氮化铝(AlN)、氧化钇(Y_(2)O_(3))、氧化铈(CeO_(2))、氧化锆(ZrO_(2))、氧化镧(La_(2)O_(3))、五氧化二钽(Ta_(2)O_(5))、钛酸钡(BaTiO_(3))、氧化钬(Ho_(2)O_(3))和由它们组合而成的堆栈栅介质。最后,对未来该领域的研究方向进行了展望和建议,例如对栅漏电流机理的研究、对新材料的更多尝试、器件在极端环境下的可靠性问题等。

High-performance ferroelectric based materials via high-entropy strategy:Design,properties,and mechanism

High-performance ferroelectric materials are widely used in various electronic devices owing to the function of mutual conversion among different energies,which mainly relates to their special structure gene of polarization configuration.Recent researches show that the high-entropy strategy has emerged as an effective and flexible approach for boosting physical properties in high-entropy ferroelectrics via the delicate design of local polarization configurations and other intrinsic effects caused by entropy increment,such as entropy stabilization,lattice disorder,inhibition of grain coarsening,improved mechanical properties,cocktail effect,and so on.In this review,the recent research progress about high-entropy ferroelectrics has been summarized,especially for the directional design of novel local polarization configurations according to the characteristics of different electrical properties such as high piezoelectricity,high-efficiency energy storage,and large electrostriction,providing a guidance for designing and exploring more novel local polarization configurations in high-entropy ferroelectrics for generating higher performance.

Cascading V_(2)O_(3)/N-doped carbon hybrid nanosheets as high-performance cathode materials for aqueous zinc-ion batteries

In recent years, especially when there is increasing concern about the safety issue of lithium-ion batteries (LIBs), aqueous Zn-ion batteries (ZIBs) have been getting a lot of attention because of their cost-effectiveness, materials abundance, high safety, and ecological friendliness. Their working voltage and specific capacity are mainly determined by their cathode materials. Vanadium oxides are promising cathode materials for aqueous ZIBs owing to their low cost, abundant resources, and multivalence. However, vanadium oxide cathodes still suffer from unsatisfactory capacity, poor stability, and low electrical conductivity. In this work, cascading V_(2)O_(3)/nitrogen doped carbon (V_(2)O_(3)/NC) hybrid nanosheets are prepared for high-performance aqueous ZIBs by pyrolyzing pentyl viologen dibromide (PV) intercalated V_(2)O5 nanosheets. The unique structure features of V_(2)O_(3)/NC nanosheets, including thin sheet-like morphology, small crystalline V_(2)O_(3) nanoparticles, and conductive NC layers, endow V_(2)O_(3)/NC with superior performance compared to most of the reported vanadium oxide cathode materials for aqueous ZIBs. The V_(2)O_(3)/NC cathode exhibits the discharge capacity of 405 mAh/g at 0.5 A/g, excellent rate capability (159 mAh/g at 20 A/g), and outstanding cycling stability with 90% capacity retention over 4000 cycles at 20 A/g.

2024年我国化工新材料科技与产业进展

化工新材料是指在化学化工研发、制备和应用过程中,有新结构、新方法、新性能指标、新应用的化工材料,是国民经济基础性产业。近些年,我国化工新材料科技和产业发展速度较快,特别表现在储能材料、光电转换材料、光催化材料、电子材料、先进复合材料用树脂及高性能纤维材料、功能性涂料和粘合剂等方面,已在风电光电、新能源汽车、航空航天、半导体封测等多个领域发挥重要作用,形成新质生产力。中国化工学会化工新材料专委会将每年组织学会专家学者编写当年的化工新材料的科技产业进展情况,发表在《化工新型材料》杂志上与广大读者见面。

高性能复合材料在隧道桥梁施工成本控制中的创新应用

文章首先介绍了高性能复合材料的特性,分析其在结构轻量化、施工便利性和耐久性提升等方面的优势,以及阐述了如何使用复合材料来有效降低工程成本方法;其次,讨论了复合材料在结构设计中的创新应用,包括支承结构优化、新型结构形式和智能监测系统集成等方面;最后,提出了复合材料在隧道桥梁施工中的优化策略,以进一步提升其应用效果和经济性。