Growth and physical characterization of high resistivityFe:β-Ga2O3 crystals

High quality 0.02 mol%,0.05 mol%,and 0.08 mol%Fe:β-Ga2O3 single crystals were grown by the floating zone method.The crystal structure,optical,electrical,and thermal properties were measured and discussed.Fe:β-Ga2O3 single crystals showed transmittance of higher than 80%in the near infrared region.With the increase of the Fe doping concentration,the optical bandgaps reduced and room temperature resistivity increased.The resistivity of 0.08 mol%Fe:β-Ga2O3 crystal reached to 3.63×1011Ω·cm.The high resistivity Fe:β-Ga2O3 single crystals could be applied as the substrate for the high-power field effect transistors(FETs).

Mapping coalmine goaf using transient electromagnetic method and high density resistivity method in Ordos City, China

The research about subsurface characteristics by using transient electromagnetic method（TEM） and high density resistivity method（HDRM） were already conducted in Ordos. The objective of this research is to detect coalmine goaf areas based on rock resistivity. The data processing using wavelet transform, three point smoothing, RES2 DINV and Maxwell processing software to obtain 2D resistivity structure. The results showed that the layers with maximum resistivity values（30e33 U m on Line 1, 30e31 U m on Line 2, 32e40 U m on Line3） are founded at station 1e7, and 14e20 on Line 1,13e18 on Line 2, and 8e13 and 16e20 on Line 3 which is predicted as goaf layer, and the minimum resistivity values（20e26 U m of TEM, 45e75 U m of HDRM） at the other layers. This resistivity difference was caused by the geology and characteristics of the study area which is located close by the cleugh with rich coal, so the goaf area distinguishable with aquifer layer and coal seam. The results were also significant accidents and serious destruction of ecological environment.

High Water Resistance and Enhanced Mechanical Properties of Bio-Based Waterborne Polyurethane Enabled by in-situ Construction of Interpenetrating Polymer Network

In this study,acrylic acid was used as a neutralizer to prepare bio-based WPU with an interpenetrating polymer network structure by thermally induced free radical emulsion polymerization.The effects of the content of acrylic acid on the properties of the resulting waterborne polyurethane-poly(acrylic acid)(WPU-PAA)dispersion and the films were systematically investigated.The results showed that the cross-linking density of the interpenetrating network polymers was increased and the interlocking structure of the soft and hard phase dislocations in the molecular segments of the double networks was tailored with increasing the content of acrylic acid,leading to enhancement of the mechanical properties and water resistance of WPU-PAA films.Notably,with the increase in content of acrylic acid,the tensile strength,Young’s modulus,and toughness of the WPU-PAA-110 film increased by 3 times,and 8 times,and 2.4 times compared with WPU-PAA-80,respectively.The WPU-PAA-100 film showed the best water resistance,and the water absorption rate at 96 h was only 3.27%.This work provided a new design scheme for constructing bio-based WPU materials with excellent properties.

Development of a High-Temperature Thixotropic Cement Slurry System

Cementing carbonate reservoirs is generally a difficult task.The so-called thixotropic cement slurry has gained considerable attention in this regard as it can help tofix some notable problems.More precisely,it can easilyfill the leakage layer;moreover,its gelling strength can grow rapidly when pumping stops,thereby increasing the resistance to gas channeling,effectively preventing this undesired phenomenon in many cases.High-temperature thixotropic cement slurry systems,however,are still in an early stage of development and additional research is needed to make them a viable option.In the present study,using a self-developed composite high-temperature thixotropic additive as a basis,it is shown that the compressive strength can be adjusted by tuning the proportion of silica sand,the high-temperature retarder,fluid loss additive and dispersant(compatible with the thixotropic additive).According to the tests,the developed high-temperature thixotropic cement slurry system has a 14 d compressive strength of 29.73 MPa at 150°C,and a thickening time of 330 min when the dosage of retarder is 2%.At the same time,the rheological property,water loss,permeability,water separation rate,and settlement stability of the cement slurry system meet the requirements of cementing construction.

Molecular Mechanism of Rice Necrotic Lesion for Optimized Yield and Disease Resistance

How to balance rice resistance and yield is an important issue in rice breeding.Plants with mutated necrotic lesion genes often have persistent broad-spectrum resistance,but this broad-spectrum resistance usually comes at the expense of yield.Currently,many necrotic lesion mutants in rice have been identified,and these genes are involved in disease resistance pathways.This review provides a detailed introduction to the characteristics,classification,and molecular mechanisms of necrotic lesion formation.Additionally,we review the molecular regulatory pathways of genes involved in rice disease resistance.Concurrently,we summarize the relationship between resistance and yield in rice using newly developed gene editing methods.We discuss a rational and precise breeding strategy to better utilize molecular design technology for breeding disease-resistant and high-yield rice varieties.

Effect of Soy Isoflavone Crude Extract Supplementation on High Fat Diet-induced Insulin Resistance in Ovariectomized Rats

Female Wister rats aged 8 weeks were randomly divided into sham operation group, ovariectomized （OVX） control group, and 20VX groups fed with soy isoflavone crude extract supplementation. The rats had free access to high fat diet and water for 9 weeks. No significant difference was found in body weight （BW）, total abdominal fat, food intake and food utilization rate between OVX control group and 20VX groups. However, the fasting blood glucose and blood lipid levels were significantly higher in 20VX groups than in OVX control group （P〈0.05）. Intraperitoneal glucose tolerance test （IGTI＂） showed that the area under AUC was smaller in 20VX groups than in OVX control group （P〈0.05）. These findings showed that soy isoflavone crude extract supplementation can improve glucose tolerance and prevent high fat diet-induced insulin resistance in ovariectomized rats.

Layer regrouping for water-flooded commingled reservoirs at a high water-cut stage

Layer regrouping is to divide all the layers into several sets of production series according to the physical properties and recovery percent of layers at high water-cut stage, which is an important technique to improve oil recovery for high water-cut multilayered reservoirs. Dif- ferent regroup scenarios may lead to different production performances. Based on unstable oil-water flow theory, a multilayer commingled reservoir simulator is established by modifying the production split method. Taking into account the differences of layer properties, including per- meability, oil viscosity, and remaining oil saturation, the pseudo flow resistance contrast is proposed to serve as a characteristic index of layer regrouping for high water-cut multilayered reservoirs. The production indices of multi- layered reservoirs with different pseudo flow resistances are predicted with the established model in which the data are taken from the Shengtuo Oilfield. Simulation results show that the pseudo flow resistance contrast should be less than 4 when the layer regrouping is implemented. The K-means clustering method, which is based on the objec- tive function, is used to automatically carry out the layer regrouping process according to pseudo flow resistances. The research result is applied to the IV-VI sand groups of the second member of the Shahejie Formation in the Shengtuo Oilfield, a favorable development performance is obtained, and the oil recovery is enhanced by 6.08 %.

Screening of High Temperature Resistant Fodder Yeast Strains

[ Objective] This study aimed to screen yeast strains suitable for high temperature processing of formulated biological feed. [ Method ] High temperature resistance and culture conditions of six yeast strains were investigated. [Result] Two yeast strains resistant to high temperature （45 ℃ ） with high viable cell number （10^8 cells/ml） were screened, including DQFC2117-1 and DQFC2122-2. [ Conclusion] Strains DQFC2117-1 and DQFC2122-2 could be used as high temperature resistant yeast strains for processing of formulated biological feed.

Plugging property and displacement characters of a novel high-temperature resistant polymer nanoparticle

The goal of the research was to investigate the profile control and oil displacement characteristics of the polymer nanoparticles after high temperature swelling.The displacement parameters showed considerable influence on the plugging effect of the high-temperature swelled polymer nanoparticles,such as the core permeability,concentration of nanoparticles in the suspension,swelling time and swelling temperature,which makes it flexible to control the plugging effect by controlling displacement experiments conditions.Experimental results show that polymer nanoparticles dispersion system with a concentration of 500 mg/L is suitable for cores plugging with a permeability of 30×10^(-3)-150×10^(-3)μm^(2),even after aging at 150℃ for three months.The shunt flow experiments show that when the displacement factors are optimal values,the polymer nanoparticles after high temperature swelling to plug the high-permeability layer selectivity and almost do not clog the low-permeability layer.Oil recovery of homogeneous artificial core displacement experiment and a heterogeneous double-tube cores model are increased by 20%and 10.4%on the basis of water flooding.The polymer nanoparticles can be a great help for petroleum engineers to better apply this deep profile control and flooding technology.

Very Low Power,Low Voltage,High Accuracy,and High Performance Current Mirror

A novel low power and low voltage current mirror with a very low current copy error is presented and the principle of its operation is discussed. In this circuit, the gain boosting regulated cascode scheme is used to improve the output resistance, while using inverter as an amplifier. The simulation results with HSPICE in TSMC 0.18 μm CMOS technology are given, which verify the high performance of the proposed structure. Simulation results show an input resistance of 0.014 Ω and an output resistance of 3 GΩ. The current copy error is favorable as low as 0.002% together with an input （the minimum input voltage of Vin,min- 0.24 V） and an output （the minimum output voltage of Vout,min~ 0.16 V） compliances while working with the 1 V power supply and the 50 μA input current. The current copy error is near zero at the input current of 27 μA. It consumes only 76μW and introduces a very low output offset current of 50 pA.

Structures and Properties of High-Carbon High Speed Steel by RE-Mg-Ti Compound Modification

The effects of rare earths(RE)-Mg-Ti compound modification on the structures and properties of high-carbon high speed steel(HSS) were researched.The impact toughness(α_k),the fracture toughness(K_(1c))and threshold of fatigue crack growth(ΔK_(th))are tested.The thermal fatigue test is done on a self-straining thermal fatigue tester,the wear test is done on a high temperature wear test machine.The results show that the matrix can be refined by the RE-Mg-Ti compound modification,the eutectic carbides are inclined to spheroidicize and are distributed evenly,the morphology and distribution of eutectic carbides are improved by appropriate RE-Mg-Ti complex modification.After RE-Mg-Ti compound modification,a little effects can be found on the strength,hardness and red hardness,but the fracture toughness(K_(1c)) and threshold of fatigue crack growth(△K_(th)) are improved in the meantime,the impact toughness (α_k) is increased by over one time,and the resistance to thermal fatigue and wear resistance at an elevated temperature are remarkably improved.

Laboratory Study on 210°C High Temperature and Salt Resistant Drilling Fluid

Combined with the current research status in this area at home and abroad, with the improvement of salt and high temperature resistance as the research goal, the laboratory research of salt and high temperature resistant drilling fluid system has been carried out, and lubricants, inhibitors and stabilizers have been optimized. The final drilling fluid formula is: water + 3% sepiolite + 0.3% Na2CO3 + 3% RH-225 + 3% KCOOH + 3% G-SPH + 3% CQA-10 + 1.5% ZX-1 + Xinjiang barite, density 2.2 g/cm3, using hot-rolling furnace, environmental scanning electron microscope, high temperature and high pressure plugging instrument and Zeiss microscopes and other instruments use core immersion experiments, permeability recovery value experiments, and static stratification index methods to perform temperature resistance, reservoir protection, plugging performance, and static settlement stability performance of the configured drilling fluid., Inhibition performance, biological toxicity, salt resistance, anti-pollution performance have been tested, and it is concluded that the temperature resistance is good under the condition of 210°C, and the salt resistance can meet the requirements of 20% NaCl + 0.5% CaCl2 concentration. It has a good reservoir protection effect, the permeability recovery value can reach more than 90%, the performance of restraining water dispersion and cuttings expansion is good, the heat roll recovery rate can reach more than 85%, and the SSSI value shows that its settlement stability performance is good;Its plugging performance is good under high temperature and high pressure. It laid the foundation for the next step to promote the field application of the drilling fluid system.

Resequencing-based QTL mapping for yield and resistance traits reveals great potential of Oryza longistaminata in rice breeding

As a natural genetic reservoir, wild rice contains many favorable alleles and mutations conferring high yield and resistance to biotic and abiotic stresses. However, there are few reports describing favorable genes or QTL from the AA genome wild rice O. longistaminata, which is characterized by tall and robust habit and long tassels and anthers and shows high potential for use in cultivated rice improvement. We constructed a stable BC_(2)F_(20) backcross inbred line(BIL) population of 152 lines from the cross of 9311 × O.longistaminat. Some BILs showed large panicles, large seeds, and strong resistance to rice false smut, bacterial leaf blight, rice blast spot, and brown planthopper. Genomic resequencing showed that the 152 BILs covered about 99.6% of the O. longistaminata genome. QTL mapping with 2432 bin markers revealed 13QTL associated with seven yield traits and eight with resistance to brown planthopper and to four diseases. Of these QTL, 12 for grain yield and 11 for pest and disease resistance are novel in Oryza species.A large-panicle NIL1880 line containing QTL qPB8.1 showed a nearly 50% increase in spikelet number and27.5% in grain yield compared to the recurrent parent 9311. These findings support the potential value of O. longistaminata for cultivated rice improvement.

Analysis of Metallographic Characteristics of Aluminum Alloy for Turbocharged Impellers

In this paper, the composition, two-dimensional and three-dimensional microstructure of heat-resistant wrought aluminum alloy with strong oxidation resistance, heat resistance and easy processing are analyzed by using direct reading spectrometer, metallographic microscope and scanning electron microscope. The main alloy elements of heat-resistant forging aluminum alloy include Cu, Mg, Si, Ni and Fe. The α solid solution of each element in aluminum consists of S phase (Al2CuMg), Mg2Si phase, bright gray Al2CuNi phase and dark brown Al9FeNi phase. The distribution of each phase in the aluminum alloy is determined by the three-dimensional energy spectrum analysis of the microstructure, and the distribution of each phase in the crystal position is analyzed. The mechanism of heat resistance, easy processing type and wear resistance is obtained, which provides the theoretical basis for the development and use of heat-resistant forged aluminum alloy.

新型缔合聚合物AP调剖体系研制及矿场应用(英文)

A new polymer system, referred to simply as the AP-P4 polymer system, aims at solving the problems of high temperature, high salinity and the poor shearing resistance, all of which are encountered by conventional polymers (such as polyacrylamide) used in profile control, profile performance improvement and EOR operations in the Zhongyuan Oilfield, Sinopec. This system has been developed on the basis of the specific molecular structure and the better properties of high temperature resistance, high salinity resistance and strong shearing resistance of the new type of AP-P4 association polymer. Acidity modifying agents and cross-linking agents (MZ-YL, MZ-BE, MZ-XS), compatible with the new polymer system, are selected. Results of performance tests have shown that the new polymer system has excellent thickening, high temperature, high salinity and shearing resistance and anti-dehydrating properties. In 2003, it underwent its first pilot test in 26 wells in China, with remarkable effects in increasing oil production and decreasing water production. The newly developed polymer system and its application technology described in this paper may play a guiding role in polymer profile control operations in the oil reservoirs of high temperature and high salinity.

Anti-Crack Performance of Low-Heat Portland Cement Concrete

The properties of low-heat Portland cement concrete（LHC） were studied in detail. The experimental results show that the LHC concrete has characteristics of a higher physical mechanical behavior, deformation and durability. Compared with moderate-heat Portland cement（MHC）, the average hydration heat of LHC concrete is reduced by about 17.5%. Under same mixing proportion, the adiabatic temperature rise of LHC concrete was reduced by 2 ℃-3 ℃,and the limits tension of LHC concrete was increased by 10× 10^-6-15×10^-6 than that of MHC. Moreover, it is indicated that LHC concrete has a better anti-crack behavior than MHC concrete.

Development and application of a new hot-work die steel for hot stamping

A new hot-work die steel for hot stamping was developed, and used the die for mass production. The produced die showed good performance owing to its high heat conductivity and wear-resistant characteristics. Two different benchmarking hot-work die steels were investigated, and then compared in terms of their impact ductility, temper characteristics ,heat conductivity, and thermal stability. The result of the high-temperature friction wear test indicated that oxidative wear was the main mode in high temperature. On the basis of the comparison and test results, the alloying composition of the new hot-work die steel was especially designed. The new die steel showed good performance with good wear-resistant quality, as well as temper hardness and heat conductivity of HRC 50 and 34.3 W/（ m ~ K）, respectively. Furthermore, without surface plasma nitriding, the die made of the new steel had no obvious galling with 6 142 strokes. After surface plasma nitriding, the die completed 40 000 strokes with good surface. The die life is expected to exceed 200 000 strokes.

IMPROVEMENT OF TYPE IV CRACKING RESISTANCE OF 9Cr HEAT RESISTING STEEL WELDMENT BY BORON ADDITION

Creep lives of high Cr ferritic heat resisting steel weldments decrease due to Type Ⅳ fracture, which occurs as a result of formation and growth of creep voids and cracks on grain boundaries in fine-grained heat affected zone (HAZ). Because boron is considered to suppress the coarsening of grain boundary precipitates and growth of creep voids, we have investigated the effect of boron addition on the creep properties of 9Cr steel weldments. Four kinds of 9Cr3WSCoVNb steels with boron content varying from 4.7×10-5 to 1.8×10-4 and with nitrogen as low as 2.0×10-5 were prepared. The steel plates were welded by gas tungsten arc welding and crept at 923K. It was found that the microstructures of HAZ were quite different from those of conventional high Cr steels such as P91 and P92, namely the fine-grained HAZ did not exist in the present steel weldments. Boron addition also has the effect to suppress coarsening of grain boundary carbides in HAZ during creep. As a result of these phenomena, the welded joints of present steels showed no Type Ⅳ fractures and much better creep lives than those of conventional steels.

Zirconia Hollow Spheres and Their Application

Zirconia hollow sphere products are ultra-high temperature energy saving lightweight insulating refractories in zirconia system.They not only have the same refractoriness as zirconia products,but also have the advantages of low bulk density and excellent thermal insulation properties.Their thermal conductivity is 0.3-0.4 W · m-1 · K-1 only 1/2 of that of the ordinary zirconia products.They are special refractories which can be used steadily up to 2 400 ℃ in oxidation,reduction and vacuum atmospheres.Zirconia hollow sphere products are the best lining refractories for various ultra-high temperature kilns and furnaces of tungsten and molybdenum metal products processing,artificial crystals,and quartz industrial production.

Effect of molecular structure and slump loss resistance of polycarboxylate superplasticizers on self-compacting concrete

A new kind of polycarboxylate superplasticizer with high slump loss resistance was obtained by designing scheduled molecular structure.The number average molecular mass of the polymer was characterized by the gel permeation chromatography measurements.And chemical structure of the polymer was observed by the Fourier transform infrared spectroscopy(FT-IR).The results show that the good workable maintaining of self-compacting concrete could be achieved through direct adjustment of number average molecular mass and different unsaturated monomer in synthetic process.The FT-IR analysis illustrated that the high slump loss resistance of polycarboxylate superplasticizers with ester and carboxyl group and expectations of molecular structure were designed.