Unveiling the underlying mechanism of forming edge cracks upon high strain-rate rolling of magnesium alloy

In the current study,high strain-rate rolling(≥10 s-1) has been successfully employed to produce Mg-3 A1-1 Zn alloy sheets to a high reduction of 82% with a fine grain structure in a single pass.The underlying mechanism of forming primary and secondary edge cracks has been investigated.It is found that dynamic recrystallization(DRX) induced by subgrains tends to blunt cracks,while twinning-induced D RX is mainly observed around sharp crack tips.The motion of emitted dislocations from blunted cracks is inhibited by the DRX grain boundaries.This,on one hand,increases local work hardening,and on the other hand,causes stress concentration alo ng grain boundaries especially in the triple junctions leading to the formation of secondary cracks.

Effects of Calcium and Yttrium on Microstructure and Mechanical Properties of High Strain-Rate Rolled AZ91D Magnesium Alloy

Effects of calcium( Ca) and yttrium( Y) on microstructure and mechanical properties of high strain-rate rolled AZ91 D magnesium alloy were studied. High strain-rate rolling can improve the strength and plasticity of magnesium alloy sheets.Additions of Ca and Y into AZ91 D can refine grains and modify the size and the distribution of the precipitated phases. After solution treatment( 418 ℃ and 20 h) and high strain-rate rolling( heating at420 ℃ for 10 min firstly and then rolling from 10 mm to 2 mm in thickness via a single pass),the tensile strength of the AZ91 D-0. 2%Ca alloy was 1. 3% higher than that of the AZ91 D-0. 4 D%Y alloy,and the tensile strength of the AZ91 D-0. 2%Ca-0. 4%Y alloy was about 8. 3% and 6. 9% higher than those of the AZ91 D-0. 4%Y and the AZ91 D-0. 2%Ca alloys respectively.

Influence of Low Speed Rolling Movement on High Electrical Breakdown for Water Dielectric with Microsecond Charging

By means of a coaxial apparatus, high electrical breakdown experiments are carried out in the rest state and the low speed rolling state with microsecond charging and the experimental results are analyzed. The conclusions are： （1） the breakdown stress of water dielectric in the rolling state is in good agreement with that in Martin formula, and so is that in the rest state; （2） the breakdown stress of water dielectric in the rolling state is about 5% higher than that in the rest state; （3） the results simulated with ANSYS demonstrate that the breakdown stress of water dielectric decreases when the bubbles appear near the surface of electrodes; （4） the primary mechanism to increase the breakdown stress of water dielectric in the rolling state is that the bubbles are driven away and the number of bubbles near the surface of electrodes is decreased by rolling movement.

Strain rate and cold rolling dependence of tensile strength and ductility in high nitrogen nickel-free austenitic stainless steel

The tensile strength and ductility of a high nitrogen nickel-free austenitic stainless steel with solution and cold rolling treatment were investigated by performing tensile tests at different strain rates and at room temperature. The tensile tests demonstrated that this steel exhibits a significant strain rate and cold rolling dependence of the tensile strength and ductility.With the increase of the strain rate from 10^-4s^-1to 1 s^-1, the yield strength and ultimate tensile strength increase and the uniform elongation and total elongation decrease. The analysis of the double logarithmic stress–strain curves showed that this steel exhibits a two-stage strain hardening behavior, which can be well examined and analyzed by using the Ludwigson equation. The strain hardening exponents at low and high strain regions（n2and n1） and the transition strain（εL） decrease with increasing strain rate and the increase of cold rolling RA. Based on the analysis results of the stress–strain curves, the transmission electron microscopy characterization of the microstructure and the scanning electron microscopy observation of the deformation surfaces, the significant strain rate and cold rolling dependence of the strength and ductility of this steel were discussed and connected with the variation in the work hardening and dislocation activity with strain rate and cold rolling.

Effect of Rolling Process on Microstructure and Wear Properties of High Carbon Equivalent Gray Cast Iron

Rolling process based on the plastic deformation as a surface strengthening treatment was employed,aiming to improve the wear resistance ability and functional performance of the high carbon equivalent gray cast iron(HCEGCI).The microstructures and tribological performance of the untreated and rolled samples were characterized.In addition,the wear mechanism of HCEGCI samples was also studied via pin-on-disc tests.The experimental results show that the as-rolled samples possess the structure-refined layer of 15μm and work-hardened layer of 0.13 mm.In comparison with the surface hardness of untreated samples,the surface hardness of as-rolled samples increases by 84.6%(from 240HV0.1 to 443HV0.1)and the residual compressive stresses existed within the range of 0.2 mm.The wear rates of as-rolled samples were decreased by 38.4%,37.5%,and 44.4%under different loads of 5 N,10 N,and 15 N,respectively.The wear characteristics of the untreated samples mainly exhibit the peeling wear coupled with partial adhesive and abrasive wear.However,as for the as-rolled samples,the adhesive wear was limited by the structure-refined layer and the micro-crack propagation was controlled by the work-hardened layer.Therefore,the wear resistance of as-rolled samples can be improved significantly due to the low wearing degree of the friction contact zone.

Microstructural morphology of the semi-solid high carbon steel T12 before and after rheo-rolling

The semi-solid high carbon steel T12 was rolled in a closed box groove under a certain condition by the rheo-rolling equipment, and the microstructural morphology of the semi-solid T12 before and after deformation was investigated by optical mi- croscope to analyze and summarize the microstructure evolution law of T12 deformed in semi-solid state. The experiment results show that the grain shape before deformation of the semi-solid T12 steel displays globule or ellipse by the electromagnetic stirring, the distribution of solid and liquid phases is homogeneous. But the microstructure of semi-solid product after rheo-rolling exhibits macrosegregation that the distribution of liquid and solid phases changes, the liquid phases divorce from the solid phases. In the transverse section, most of the solid phases get together in the center of the specimen, the liquid phases flow to the surface or the edge of the specimen, and the grains occur plastic deformation while reduction increased. In longitudinal section, the middle micro- structure of the specimen is more homogeneous than that at the head or tail, the head microstructure is similar to the tail and the size of the grains is not homogeneous.

Advanced test methods of material property characterization:high strain-rate testing and experimental simulation of multiaxial stress states

Optimum utilization of the loading capability of engineering materials is an important and active contribution to protect nature's limited resources,and it is the key for economic design methods.In order to make use of the materials' resources,those must be known very well;but conventional test methods will offer only limited informational value.The range of questions raised is as wide as the application of engineering materials,and partially they are very specific.The development of huge computer powers enables numeric modelling to simulate structural behaviour in rather complex loading environments-so the real material behaviour is known under the given loading conditions.Here the art of material testing design starts.To study the material behaviour under very distinct and specific loading conditions makes it necessary to simulate different temperature ranges,loading speeds, environments etc.and mostly there doesn't exist any commonly agreed test standard.In this contribution two popular,non-standard test procedures and test systems will be discussed on the base of their application background,special design features as well as test results and typically gained information:The demand for highspeed tests up to 1000 s^(-1) of strain rate is very specific and originates primarily in the automotive industry and the answers enable CAE analysis of crashworthiness of vehicle structures under crash conditions.The information on the material behaviour under multiaxial loading conditions is a more general one.Multiaxial stress states can be reduced to an equivalent stress,which allows the evaluation of the material's constraint and criticality of stress state.Both discussed examples shall show that the open dialogue between the user and the producer of testing machines allows custom-tailored test solutions.

Dynamic Response of Pultruded Glass-Graphite/Epoxy Hybrid Composites Subjected to Transverse High Strain-Rate Compression Loading

In a previous study, the energy absorption and dynamic response of different combinations of cylindrical fiber-reinforced pultruded hybrid composite samples made of unidirectional glass and graphite fiber/epoxy, were investigated under longitudinal compression loading. It was found that placing glass fibers in the inner core of composites resulted in a higher ultimate compressive strength and specific energy absorption. In this study, the dynamic responses of pultruded glass-graphite/epoxy hybrid specimens with rectangular cross-section subjected to transverse compression loading are reported. Crack initiation and propagation was monitored using a high-speed video camera, and the effects of hybridization were analyzed. It was found that the location of glass or graphite fibers inside the pultruded composites has no significant effect on the ultimate compressive strength under such transverse compression loading. The energy absorption in all the hybrid specimens was almost identical. Graphite/epoxy composite showed higher specific energy absorption due to its lower density, and glass/epoxy composite had the lowest specific energy absorption.

Energy Absorption of Pultruded Glass-Graphite/Epoxy Hybrid Composites under High Strain-Rate Induced Transverse Tension

This paper focuses on the dynamic tensile response of glass-graphite/epoxy composites illustrating improvement in energy absorption through hybridization. The dynamic response and energy absorption characteristics of pultruded hybrid combinations of glass and graphite fibers in an epoxy matrix subjected to induced transverse tension at high strain-rate in a modified Split Hopkinson Pressure Bar (SHPB) apparatus, are presented. Transverse tensile strength was determined by diametral compression of disc samples (Brazilian indirect tensile test method). Diametral crack initiation and strain to failure were monitored with a Shimadzu HPV-2 high-speed video camera at a recording speed of 500,000 fps and Digital Image Correlation (DIC). Adequate measures were taken to ensure that initiation of specimen failure occurred at the exact center of the disc specimen, and propagated through the diameter along the compressive loading axis, for the induced transverse tension tests to be valid. A study of the strength and specific energy absorption demonstrates the benefits of hybridization. Under induced transverse tensile loading condition, the pure glass/epoxy (GL60) exhibited higher strength than pure graphite/epoxy (GR60). Pure graphite/epoxy (GR60) has higher specific energy absorption capacity than pure glass/epoxy (GL60) in transverse tension. Among all hybrids, GR30 has the highest specific energy absorption under transverse tension. Overall, hybrid GL48, with 48% low-cost glass fibers in the inner core and 12% high-cost graphite fibers in outer shell, was found to exhibit better performance under induced transverse tension at high strain-rates, showing the benefits of hybridization.

Wear Mechanisms of High Chromium Iron Roll under Hot Rolling Conditions

By using a reformed laboratory rolling mill,hot wear test under near service conditions has been carried out to examine the wear mechanisms of high chromium iron roll.Each time after being rolled up to a given cycle,the worn morphology of roll surface was examined under SEM and occasionally by AES.Based on rolling conditions and lasting of in-service time,various wear characteristics have been identified distinctly.It involves abrasive wear and oxidation wear for matrix phase,fatigue wear,polishing wear and grain pull-out wear for carbides,smear adhesive wear,chemical wear,and in extreme case,plasticity-dominated wear.At the same time,wear type is also discussed compatibly in terms of abrasive wear,fatigue wear,as well as chemical wear according to conventional classification.And only in an extreme situation,i.e.rolling without cooling water,adhesive wear may partially be involved.At anytime under specified conditions,there are always several wear mechanisms occurring simultaneously,but usually only one of them can be identified as the dominant mode.And finally a wear mechanism figure can be depicted to qualitatively describe the relationship among them.

Forced transverse vibration of rolls for four-high rolling mill

In order to investigate the forced transverse vibration of rolls under distributed draught pressure and moment of bending roll force,the forced transverse vibration model of rolls for four-high rolling mill was established. The work roll and backup roll were considered as elastic continuous bodies that were joined by a Winkler elastic layer. According to Euler-Bernoulli beam theory,the forced transverse vibration of rolls was analyzed based on modal superposition method. The forced vibration equations were established when the draught pressure and moment of bending roll force were imposed on the rolls respectively. Numerical modeling was made on 2 030 mm cold tandem rolling mill of Baoshan Iron and Steel Company. Simulation results show that when the work roll is only subjected to different forms of draught pressures,the vibration curves of work roll and backup roll are quadratic curves with amplitudes of 0.3 mm and 45 μm,respectively. When only the moments of bending roll force are imposed on the work roll and backup roll,the vibration curves of work roll and backup roll are quadratic curves,and the amplitudes are 5.0 and 1.6 μm,respectively. The influence of moment of bending roll force on the vibration of work roll is related with the bending roll force.

A study on centrifugal casting of high speed steel roll

High speed steel (HSS) rolls can replace traditional rolls such as alloyed cast iron rolls and powder metallurgical (PM) hard alloy rolls. The main reasons for the replacement are that the wear resistance of low-cost alloyed cast iron rolls is poor and the cost of high-quality PM hard alloy rolls is very high. By means of centrifugal casting, HSS rolls having excellent wear resistance have been manufactured. The hardness of the HSS roll is 6.5~67 HRC, the range of variation is smaller than 2 HRC and its impact toughness is 15 J/cm2. The wear rate of HSS rolls used in the pre-finishing stands of high-speed hot wire-rod rolling mill reaches 2.5×10-4mm per ton steel. Furthermore, the manufacturing cost of HSS rolls is significantly lower than that of PM hard alloy rolls; it is only 30 percent of that of PM hard alloy rolls.

High strain rate superplasticity of rolled AZ91 magnesium alloy

The high strain rate superplastic deformation properties and characteristics of a rolled AZ91 magnesium alloy at temperatures ranging from 623 to 698 K（0.67Tm-0.76Tm） and high strain rates ranging from 10^-3 to 1 s^-1 were investigated.The rolled AZ91 magnesium alloy possesses excellent superplasticity with the maximum elongation of 455% at 623 K and a strain rate of 10-3 s-1,and its strain rate sensitivity m is high up to 0.64.The dominant deformation mechanism responsible for the high strain rate superplasticity is still grain boundary sliding（GBS）,and the dislocation creep mechanism is considered as the main accommodation mechanism.

Microstructural evolution and enhanced mechanical properties of Mg?Gd?Y?Zn?Zr alloy via centrifugal casting, ring-rolling and aging

A ring-shaped Mg?8.5 Gd?4 Y?1 Zn?0.4 Zr(wt%) alloy was manufactured via centrifugal casting and ring-rolling process. The effects of accumulative ring-rolling reduction amount on the microstructure, texture, and tensile properties of the alloy were investigated. The results indicate that the microstructure of centrifugal cast alloy consists of equiaxed grains and network-like eutectic structure present at grain boundaries. The ring-rolled alloy exhibits a characteristic bimodal microstructure composed of fine dynamic recrystallized(DRXed) grains with weak basal texture and coarse un-DRXed grains with strong basal texture, along with the presence of LPSO phase. With increasing amount of accumulative ring-rolling reduction, the coarse un-DRXed grains are refined via the formation of increasing amount of fine DRXed grains. Meanwhile, the dynamic precipitation of Mg5 RE phase occurs, generating a dispersion strengthening effect. A superior combination of strength and ductility is achieved in the ring-rolled alloy after an accumulative rolling reduction of 80%. The tensile strength of this ring-rolled alloy after peak aging is further enhanced, reaching 511 MPa, while keeping a reasonable ductility. The salient strengthening mechanisms identified include the grain boundary strengthening of fine DRXed grains, dispersion strengthening of dynamic precipitated Mg;RE phase, short fiber strengthening of LPSO lamellae/rods, and precipitation strengthening of nano-sized prismatic β precipitates and basal γ precipitates.

Fragmentation mechanism of low-grade hematite ore in a high pressure grinding roll

The fragmentation mechanism of low-grade hematite ore in a high pressure grinding roll(HPGR) was studied based on the characteristics of comminuted products at different specific pressure levels. The major properties included the reduction ratio, liberation, specific surface energy, and specific surface area. The results showed that the fracture of low-grade hematite ore in HPGR was an interactive dynamic process in which the interaction between coarse particles of gangue minerals and fine particles of valuable minerals was alternately continuous with increased compactness and compacting strength of materials. Within a range of 2.8–4.4 N/mm^2, valuable minerals were crushed after preferentially absorbing energy, whereas gangue minerals were not completely crushed and only acted as an energy transfer medium. Within a range of 4.4–5.2 N/mm^2, gangue minerals were adequately crushed after absorbing the remaining energy, whereas preferentially crushed valuable minerals acted as an energy transfer medium. Within a range of 5.2–6.0 N/mm^2 range, the low-grade hematite ore was not further comminuted because of the "size effect" on the strength of materials, and the comminution effect of materials became stable.

Roll-to-roll imprint for high precision grating manufacturing

In this paper,a novel roll-to-roll imprint process is proposed to fabricate gratings in large area. The key challenges in roll-to-roll imprint process,such as the roller mold preparation,imprint system,misalignment of imprint roller and backup roller,and also the imprint pressure,are investigated. Various gratings with different periods and profiles are obtained by the roll-to-roll process. To calibrate the measuring ability of the self-made grating by imprint,a calibration system is built with a dual-frequency laser interferometer. By the calibration,the self-made gratings can achieve ±4μm accuracy in 45mm measuring distance.

Influence of Rare Earth Elements on Microstructure and Mechanical Properties of Cast High-Speed Steel Rolls

The influence of rare earth （RE） elements on the solidification process and eutectic transformation and mechanical properties of the high-V type cast, high-speed steel roll was studied. Test materials with different RE additions were prepared on a horizontal centrifugal casting machine. The solidification process, eutectic structure transformation, carbide morphology, and the elements present, were all investigated by means of differential scanning calorimetry （DSC） and scanning electron microscopy energy dispersive spectrometry （SEM-EDS）. The energy produced by crack initiation and crack extension was analyzed using a digital impact test machine. It was found that rare earth elements increased the tensile strength of the steel by inducing crystallization of earlier eutectic γ-Fe during the solidification process, which in turn increased the solidification temperature and thinned the dendritic grains. Rare earth elements with large atomic radius changed the lattice parameters of the MC carbide by forming rare earth carbides. This had the effect of dispersing longpole M C carbides to provide carbide grains, thereby, reducing the formation of the gross carbide and making more V available, to increase the secondary hardening process and improve the hardness level. The presence of rare earth elements in the steel raised the impact toughness by changing the mechanism of MC carbide formation, thereby increasing the crack initiation energy.

Computer simulation of core filling process of cast high speed steel roll

Core filling process of cast high speed steel roll was simulated.Ductile iron was used as core material.The influences of filling parameters,such as core filling time and core filling temperature,on the filling process were investigated.Based on the simulated results,optimal core filling parameters were determined.The predicted temperature fields show that the temperature at the roll shoulder is the lowest during the core filling process and usually causes binding defects there.Method for solving this problem was presented.

Color-stable,reduced efficiency roll-off hybrid white organic light emitting diodes with ultra high brightness

High-brightness and color-stable two-wavelength hybrid white organic light emitting diodes （HWOLEDs） with the configuration of indium tin oxide （ITO）/ N, N, N, N-tetrakis（4-methoxyphenyl）-benzidine （MeO-TPD）： tetrafluoro-tetracyanoqino dimethane （F4-TCNQ）/N,N-di（naphthalene-1-yl）-N,N-diphenyl-benzidine （NPB）/ 4,4-N,N-dicarbazolebiphenyl （CBP）： iridium （III） diazine complexes （MPPZ） 2 Ir（acac）/NPB/2-methyl-9,10-di（2-naphthyl）anthracene （MADN）： p-bis（p-N,N-di-phenyl-aminostyryl）benzene （DSA-ph）/bis（10-hydroxybenzo[h] quino-linato）beryllium complex （Bebq2）/LiF/Al have been fabricated and characterized. The optimal brightness of the device is 69932 cd/m2 at a voltage of 13 V, and the Commission Internationale de l’Eclairage （CIE） chromaticity coordinates are almost constant during a large voltage change of 6–12 V. Furthermore, a current efficiency of 15.3 cd/A at an illumination-relevant brightness of 1000 cd/m2 is obtained, which rolls off slightly to 13.0 cd/A at an ultra high brightness of 50000 cd/m2. We attribute this great performance to wisely selecting an appropriate spacer together with effectively utilizing the combinations of exciton-harvested orange-phosphorescence/blue-fluorescence in the device. Undoubtedly, this is one of the most exciting results in two-wavelength HWOLEDs up to now.

Strengthening pelletization of manganese ore fines containing high combined water by high pressure roll grinding and optimized temperature elevation system

Pelletization is one of useful processes for the agglomeration of iron ore or concentrates. However, manganese ore fines are mainly agglomerated by sintering due to its high combined water which adversely affects the roasting performance of pellets. In this work, high pressure roll grinding(HPRG) process and optimization of temperature elevation system were investigated to improve the strength of fired manganese ore pellets. It is shown that the manganese ore possesses good ballability after being pretreated by HPRG twice, and good green balls were produced under the conditions of blending 2.0% bentonite in the feed, balling for 7 min at 16.00% moisture. High quality roasted pellets with the compressive strength of 2711 N per pellet were manufactured through preheating at 1050 °C for 10 min and firing at 1335 °C for 15 min by controlling the cracks formation. The fired manganese pellets keep the strength by the solid interconnection of recrystallized pyrolusite grains and the binding of manganite liquid phase which filled the pores and clearance among minerals. The product pellets contain high Mn grade and low impurities, and can be used to smelt ferromanganese, which provides a possible way to use imported manganese ore fines containing high combined water to produce high value ferromanganese.