Texture Evolution of 440 MPa Grade Nb-bearing High Strength IF Steel during Rolling and Annealing Process

The texture evolution from rolling process to annealing process of 440 MPa grade Nb-bearing high strength IF steel （IF-HSS） was studied. Moreover, the texture of different section in thickness direction of steel sheet after annealing was investigated. Macro-texture measurements using XRD shows that hot rolling texture in Nb-bearing IF-HSS includes a weak γ-fiber and α-fiber, of which main texture components are {001}〈110〉,{111}〈110〉 and {111}〈112〉. It is worthy of note that the γ-fiber skeleton line formed after hot rolling. During cold rolling, the absolute maximum shifts to {111}〈112〉 along the γ-fiber and the maximum along the α-fiber shifts to {112} 〈110〉. During recrystallization annealing process, the weaker α-fiber and stronger γ-fiber cold rolling texture transformed to a very strong γ-fiber annealing texture. After annealing the main components from surface to mid-section along thickness display the same character for both α-fiber and γ-fiber, while textures intensity at 1/4 section is higher than that of surface and mid-section.

Ultrahigh strength and improved electrical conductivity in an aging strengthened copper alloy processed by combination of equal channel angular pressing and thermomechanical treatment

In this paper,equal channel angular pressing and thermomechanical treatment was employed to improve the strength and electrical conductivity of an aging strengthened Cu-Ti-Cr-Mg alloy,and the microstructure and properties of the alloy were investigated in detail.The results showed that the samples deformed by the combination of cryogenic equal channel angular pressing(ECAP)and rolling had good comprehensive properties after aging at 400℃.The tensile strength of the peak-aged and over-aged samples was 1120 MPa and 940 MPa,with their corresponding electrical conductivity of 14.7%IACS and 22.1%IACS,respectively.ECAP and cryogenic rolling introduced high density dislocations,leading to the inhibition of the softening effects and refinement of the grains.After a long time aging at 400℃,the alloy exhibited ultra-high strength with obvious increasing electrical conductivity.The high strength was attributed to the synergistic effect of work hardening,grain refinement strengthening and precipitation strengthening.The precipitation of a large amount of Ti atoms from the matrix led to the high electrical conductivity of the over-aged sample.

Development of a High Early Strength Non-fuorine and Non-alkaline Flash Setting Admixture and Flash Mechanism

To solve the problems of high rebound rate and strength reversion of shotcrete,a non-fluorine and non-alkaline liquid flash setting admixture(FSN)with low rebound and high early strength was synthesized under 60-65℃water bath environment through orthogonal test design and taking setting time and compressive strength as indicators.The experimental results show that the optimum mass ratio of FSN is aluminum sulfate:diethanolamine:triethanolamine:pseudo-boehmite:lithium carbonate:water=57%:8%:0.05%:2%:2%:31%.When FSN is added with 7%of the mass of portland cement,the cement paste can be initially set in 3 min and finally set in 5 min.The compressive strength of mortar is 1.2 MPa at 6 h,18.0 MPa at 1 d,and more than 100%at 28 days;The microscopic analysis shows that the rapid release of Li^(+),NH^(4+),and CO_(3)^(2-)ions by FSN in the paste solution effectively shortens the induction period of high C_(3)S content in Portland cement,directly forms early coagulation AFt crystals in FSN and CH dominated by Al_(2)(SO_(4))_(3),and forms a large number of C-S-H gels in the later stage,so that the cement can quickly coagulate and harden,and the strength in the later stage is not retracted.

Effect of casting process on the inner-wall band segregation of high-strength antisulfur pipes

Controlling inner-wall band segregation is one of the difficulties in the production of high-strength antisulfur pipes.Comparative tests were carried out on different casting processes(superheat,mold electromagnetic stirring,end electromagnetic stirring,casting speed and soft reduction)for the smelting of high-strength antisulfur pipes.The microstructures of continuous-casting billets and hot-rolled or tempered pipes were analyzed using a metallographic microscope and scanning electron microscope.The mechanism and evolution law regarding the inner-wall band segregation of high-strength antisulfur pipes were studied,and the influence of different casting processes was explored.

Effect of B_(2)O_(3) enrichment on microstructural inhomogeneity of high strength steel weldments

The present work attributes the role of boron on the high strength steel submerged arc weld using an undermatching filler wire.Mild steel filler wire was used for welding in constant machine parameters setting to evaluate the joint strength due to the enrichment of boron.To change the chemical composition of the weld metal,boron trioxide powder was blended with virgin flux in various proportions(2.5%−12.5%),which led to an increase in boron weight percentage in the range of 0−0.0065.The results show that weld metals(WM)optical micrographs depict the various types of ferrites,pearlites and secondary phases like martensite-austenite(M-A).Acicular ferrite content was influenced by the boron trioxide addition.Heat affected zone(HAZ)micrographs were not showing appreciable changes with oxide enrichment.Hardness and toughness of weld metals showed the mixed trend with B_(2)O_(3) enrichment whereas,small reduction in ultimate tensile strength(UTS)and yield strength(YS)was observed.

Product Development of High Strength and Toughness Spring Flat Steel

With the continuous development of mechanical industry,higher requirements are put forward for the comprehensive properties of spring steel.The chemical composition and production process of spring flat steel are designed to meet the requirements of high strength and high toughness of spring flat steel,through the test,the product surface quality and internal quality all meet the national standards,the performance indicators to meet user requirements.

Fatigue Life Estimation of High Strength 2090-T83 Aluminum Alloy under Pure Torsion Loading Using Various Machine Learning Techniques

The ongoing effort to create methods for detecting and quantifying fatigue damage is motivated by the high levels of uncertainty in present fatigue-life prediction approaches and the frequently catastrophic nature of fatigue failure.The fatigue life of high strength aluminum alloy 2090-T83 is predicted in this study using a variety of artificial intelligence and machine learning techniques for constant amplitude and negative stress ratios(R?1).Artificial neural networks(ANN),adaptive neuro-fuzzy inference systems(ANFIS),support-vector machines(SVM),a random forest model(RF),and an extreme-gradient tree-boosting model(XGB)are trained using numerical and experimental input data obtained from fatigue tests based on a relatively low number of stress measurements.In particular,the coefficients of the traditional force law formula are found using relevant numerical methods.It is shown that,in comparison to traditional approaches,the neural network and neuro-fuzzy models produce better results,with the neural network models trained using the boosting iterations technique providing the best performances.Building strong models from weak models,XGB helps to predict fatigue life by reducing model partiality and variation in supervised learning.Fuzzy neural models can be used to predict the fatigue life of alloys more accurately than neural networks and traditional methods.

Research and Development of Cemented Carbide Multifacet Drill for Drilling High Strength Steel

Aim To research on a solid cemented carbide multi facet drill for drilling high strength steel. Methods Assimilating some features of multi facet drill edge structures, through systematic drilling experiments, a new type of solid cemented carbide drill was developed and the drill geometry was optimized. Results With the new type drill,the drilling force decreases by 10%-20%, the drilling productivity (drilled holes per hour) increases by 2-3 times, and the drilling precision and surface finish increase by one level. Conclusion The new type drill possesses excellent drilling performance.

Investigation on Precipitation Hardening High Strength IF Steel Sheet for Automotive Application

High strength IF steel sheets with sufficient formability had been extensively used in automotive industry.In this paper,a new type of high strength cold-rolled IF steel with higher carbon and niobium contents was studied.Thermal plastic and continuous annealing were performed on thermo-mechanical simulator.The transformation points were tested by thermal expansion apparatus.Optical microscopy and transmission election microscope (TEM) were used to analyze the microstructure and the secondary precipitates of the steel.The results showed,the ductibility temperature range was from 950℃ to 1250℃ and the transformation points were 887℃ and 913℃ respectively.The grain size of this steel was smaller than that of conventional high strength IF steel.At the mean time,there were many fine Nb(C,N) precipitates distributed in the intra-granular regions and the PFZ (precipitate free zone) were formed in the neighborhood of grain boundaries.Due to the unique micro-structural feature,the yield strength and the yield ratio of the steel were decreased while the tensile strength was increased.With the increasing of the annealing temperature,the strength decreased,the total elongation A50,r-value at 15% strain and n-value were all increased.In order to obtain the favorable mechanical properties,the skin-pass rolling rate should be chosen at 0.6-0.8%.

Determination of Optimal Recrystallization Annealing Temperature of Nb-Ti Microalloyed High Strength IF Steel

The Nb-Ti microalloyed high strength IF steel sheet was used to study the effect of annealing temperature on the microstructures,mechanical properties and textures.The experimental results show that experimental steel is incomplete recrystallization at 750℃ annealing,but complete recrystallization from 780℃ to 870℃ under experimental conditions.When the annealing temperature was increased,the yield strength and tensile strength would gradually reduce,the plastic strain ratio and yield point elongation would gradually increase.The yield strength,tensile strength,elongation,the plastic strain ratio and the strain hardening exponent were approximate 300MPa,410MPa,36.5%,1.7 and 0.22 respectively under annealing temperature 810℃ to 840℃.When the annealing temperature was increased,the α-textures and γ-textures were gradually weakened,and the α-textures have a trend to {111} texture.Therefore,the suggestion of the optimal recrystallization annealing temperature is about 810℃ to 840℃ in industrial production.

Designing new low alloyed Mg-RE alloys with high strength and ductility via high-speed extrusion

Two new low-alloyed Mg-2RE-0.8Mn-0.6Ca-0.5Zn(wt%,RE=Sm or Y)alloys are developed,which can be produced on an in-dustrial scale via relatively high-speed extrusion.These two alloys are not only comparable to commercial AZ31 alloy in extrudability,but also have superior mechanical properties,especially in terms of yield strength(YS).The excellent extrudability is related to less coarse second-phase particles and high initial melting point of the two as-cast alloys.The high strength-ductility mainly comes from the formation of fine grains,nano-spaced submicron/nano precipitates,and weak texture.Moreover,it is worth noting that the YS of the two alloys can maintain above 160 MPa at elevated temperature of 250°C,significantly higher than that of AZ31 alloy(YS:45 MPa).The Zn/Ca solute segregation at grain boundaries,the improved heat resistance of matrix due to addition of RE,and the high melting points of strengthening particles(Mn,MgZn_(2),and Mg-Zn-RE/Mg-Zn-RE-Ca)are mainly responsible for the excellent high-temperature strength.

Development of a high-strength Mg alloy with superior ductility through a unique texture modification from equal channel angular pressing

In the current study,a homogenous ultra-fine grained microstructure with average grain size of 1.0μm is achieved in the Mg-Zn-Ca-Mn alloy through the reduplicative equal channel angular pressing(ECAP)at 300℃,and the mechanical properties are remarkably improved,with room-temperature yield strength of 269.6 MPa and elongation of 22.7%.The twinning deformation results in a discontinuous recrystallization behavior in the initial stage of ECAP.With further deformation,the continuously dynamic recrystallization contributes to an obvious grain refinement effect.The activation of non-basal slip system leads to the formation of a unique basal texture,which is related to the elevated ECAP temperature and the decreased grain size.Both grain refinement and texture modification derived from ECAP process result in the increase of yield strength,while the cracked secondary phase particles are beneficial to the enhanced ductility,through reducing the stress concentration and hindering premature failure.

Microstructure investigation of a new type super high strength aluminum alloy at different heat-treated conditions

As a structural material with low density and high strength, super-highstrength aluminum alloys have a future for wide application. However, its poor stress corrosionresistance (SCC) restricts further development. In present, retrogression and re-ageing (RRA)treatment, which can improve both strength and SCCR of 7XXX series alloy, is a best method to solvethis problem. The effect of RRA treatment on the microstructure evolution of a new type lowfrequency electric-magnetic casting Al-9.OZn-2.45Mg-2.2Cu-0.15Zr alloy was investigated using DSCand TEM technologies. The results show that the typical microstructure of the alloy at T6 conditionis characterized by both fine eta' and GP zone homogeneously distributed in the matrix andcontinuous r) particles occurred on the grain-boundary. After RRA treatment, the matrixprecipitations are mainly fine and dispersed eta' and eta phases, being coarser and more stable thanthat from T6 temper. While, the grain-boundary microstructure is very close to that resulting fromT73 temper. High retrogression temperature and long retrogression time leads to a more stablemicrostructure after re-ageing.

Properties of Sustainable High Strength Concrete with Waste Copper Slag

The present work investigates copper slag as a substitute for river sand in high-strength concrete.The concrete mixtures were manufactured with 10%,30%,50%,70%,and 100%of copper slag to evaluate the mechanical and durability properties.The experimental results indicate that replacing copper slag above 50%affects the performance characteristics of the concrete due to its high angularity and lower water absorption characteristics.The strength of concrete with 50%copper slag is improved by 5.6%,whereas the strength of concrete with 100%copper slag is reduced by 2.75%at 28 days.However,increased curing to 90days improves the strength of the former by 7.16%and reduces the latter by only 0.23%.The water absorption,porosity,and rapid chloride penetration of the concrete mixtures with 100%copper slag are increased by 10.44%,13.20%,and 19.56%compared to control concrete.Micro-structural investigations through SEM infer higher replacement of copper results in higher void formation due to its reduced water absorption.

Residual Capacity of Friction⁃Type High⁃Strength Bolted T⁃stub Connection with Nut Corrosion Damage

Corrosion is a primary cause of the slippage of friction⁃type high⁃strength bolted(FHSB)T⁃stub connections.This paper attempts to quantify the residual capacity of FHSB T⁃stub connections with corroded nuts.Firstly,corrosion simulation tests were conducted on 48 manually cut nuts to find out the relationship between the damage degree of nut section and the residual clamping force(RCF)of bolt.Then,static load tests were carried out on 24 FHSB T⁃stub connections with nuts of different degrees of damage to obtain the failure modes.By finite⁃element(FE)models,a comparative analysis was performed on the initial friction load(IFL)and ultimate strength(US)of each connection with corroded nuts.Finally,the parameters of 96 FE models for FHSB T⁃stub connections were analyzed and used to derive the calculation formulas for the degree of damage for each nut and the IFL and US of each connection.The results show that the RCF decay of a bolt is a quadratic function of the equivalent radius loss ratio and the shear failure after nut corrosion;the IFL of each connection had a clear linear correlation with the RCF of the corresponding bolts,and the correlation depends on the applied load and static friction on connecting plate interface induced by the clamping force;the static friction had little impact on the US of the connection;the proposed IFL and US formulas can effectively derive the residual anti⁃slip capacity of FHSB T⁃stub connections from the degree of damage of the corroded nut section.The research results provide a scientific basis for the replacement and maintenance of corroded bolts of FHSB T⁃stub connections.

Towards designing high mechanical performance low-alloyed wrought magnesium alloys via grain boundary segregation strategy:A review

Low-alloyed magnesium(Mg)alloys have emerged as one of the most promising candidates for lightweight materials.However,their further application potential has been hampered by limitations such as low strength,poor plasticity at room temperature,and unsatisfactory formability.To address these challenges,grain refinement and grain structure control have been identified as crucial factors to achieving high performance in low-alloyed Mg alloys.An effective way for regulating grain structure is through grain boundary(GB)segregation.This review presents a comprehensive summary of the distribution criteria of segregated atoms and the effects of solute segregation on grain size and growth in Mg alloys.The analysis encompasses both single element segregation and multi-element co-segregation behavior,considering coherent interfaces and incoherent interfaces.Furthermore,we introduce the high mechanical performance low-alloyed wrought Mg alloys that utilize GB segregation and analyze the potential impact mechanisms through which GB segregation influences materials properties.Drawing upon these studies,we propose strategies for the design of high mechanical performance Mg alloys with desirable properties,including high strength,excellent ductility,and good formability,achieved through the implementation of GB segregation.The findings of this review contribute to advancing the understanding of grain boundary engineering in Mg alloys and provide valuable insights for future alloy design and optimization.

MODIFICATION THE CEMENTIOUS MATERIAL OF ULTRA-HIGH-STRENGTH SLEEPER CONCRETE

This paper presents investigation results on the natural ultra-fine mineral flour of crystalline silica fume (CSF) and porous quartz sand stone (PQSS) which can modify cement mortar strength under hydrothermal synthesis reaction (HSR) in the autoclave-cured condition. The replacement of cement by CSF and PQSS can signifi cantly increase the Jflerural and compressive strength which reach 22MPa and 150MPa respectively and de-crease the porosity oj the cement mortar. The ratio oj fine aggregation, standard sand to cementions material has sig nificant influence on the mortar strength. The mechanisms involved in cement and natural mineral flour and the HSR are presented. CaO/SiO2 ratio ranges from 3. 20 to 1. 11. the main hydrate phase is C2SH and there is not Tober-morite through X-Ray diffraction qualitative analysis. The new and ultra-high strength cementious material as basic material of sleeper concrete can he used in prestressed reinforcement sleeper concrete.

High strength magnesium alloy with α-Mg and W-phase processed by hot extrusion

Fine-grained Mg-6Zn-4Y alloy was prepared by an ingot metallurgy process with hot extrusion at 300 ℃.The microstructure was studied by XRD,OM,SEM and TEM,and the tensile properties were tested at room temperature.The results show that the alloy is composed of α-Mg and W-phase.The microstructure of the as-extruded alloy has a bimodal grain size distribution.The fine grains with the mean size of 1.2 μm are formed by dynamic recrystallization.The coarse grains（about 23% in area fraction） are unrecrystallized regions which are elongated along extrusion direction.The engineering stress—strain curve shows a pronounced yield point.The ultimate tensile strength,yield strength,and elongation are（371±10） MPa,（350±5） MPa and（7±2）%,respectively.The high strengths are attributed to the fine-grained matrix structure enhanced by W-phase particles,nano-scaled precipitates,and strong basal plane texture.

Study on High Strength Concrete Confined by Continuous Carbon Fiber Sheet

Eight high strength concrete (HSC) prisms strengthened with continuous carbon fiber sheet(CFS)were tested.As a result of the confinement provided by CFS,the concrete would fail at a greater strain than the unconfined and then a significant increase in ductility can be achieved.The lateral pressure exerted by CFS would increase the compressive strength of the concrete,resulting in higher load bearing capacity.This paper proposes the stress strain curve of this kind of hybrid specimen,which agrees well with the test results.Based on the stress strain relationship and the assumptions proposed in this paper,a computer program was developed to analyze HSC columns,confined by CFS,which were subjected to axial compression and biaxial bending.The results shown in this paper indicate that the ductility of HSC column is significantly improved and the strength is also increased by some degree.

RESEARCH ON T SHAPED HIGH STRENGTH CONCRETE MEMBERS SUBJECTED TO AXIAL COMPRESSION AND BIAXIAL BENDING

Based on experiments, a computer program is developed. The calculated results agree well with the experimental results. The flexural behavior of T shaped high strength concrete members subjected to axial compression and biaxial bending is studied. The main factors affecting the flexural behavior of T shaped high strength concrete members are loading angle, axial compression ratio and reinforcement ratio.