Engineering failure of membrane electrode assembly caused by increasingly fuel poisoning in the high temperature polymer electrolyte membrane fuel cells fed with humidified reformate gases is firstly demonstrated here...Engineering failure of membrane electrode assembly caused by increasingly fuel poisoning in the high temperature polymer electrolyte membrane fuel cells fed with humidified reformate gases is firstly demonstrated herein this work. Based on the results of the in-situ environmental scanning electron microscope, electrochemical analyses, and limiting current method, a water-induced phosphoric acid invasion model is constructed in the porous electrode to elucidate the failure causations of the hindered hydrogen mass transport and the enhanced carbon monoxide poisoning. To optimize the phosphoric acid distribution under the inevitably humidified circumstance, a facile and effective strategy of constructing acid-proofed electrode is proposed and demonstrates outstanding stability with highly humidified reformate gases as anode fuel. This work discusses a potential defect that was rarely studied previously under practical working circumstance for high temperature polymer electrolyte membrane fuel cells, providing an alternative opinion of electrode design based on the fundamental aspects towards the engineering problems.展开更多
Fe-N-C materials with atomically dispersed Fe–N_(4) sites could tolerate the poisoning of phosphate,is regarded as the most promising alternative to costly Pt-based catalysts for the oxygen reduction in high temperat...Fe-N-C materials with atomically dispersed Fe–N_(4) sites could tolerate the poisoning of phosphate,is regarded as the most promising alternative to costly Pt-based catalysts for the oxygen reduction in high temperature polymer electrolyte membrane fuel cells(HT-PEMFCs).However,they still face the critical issue of insufficient activity in phosphoric acid.Herein,we demonstrate a P-doping strategy to increase the activity of Fe-N-C catalyst via a feasible one-pot method.X-ray absorption spectroscopy and electron microscopy with atomic resolution indicated that the P atom is bonded with the N in Fe–N_(4) site through C atoms.The as prepared Fe-NCP catalyst shows a half-wave potential of 0.75 V(vs.reversible hydrogen electrode(RHE),0.1 M H_(3)PO_(4)),which is 60 and 40 mV higher than that of Fe-NC and commercial Pt/C catalysts,respectively.More importantly,the Fe-NCP catalyst could deliver a peak power density of 357 mW·cm^(−2)in a high temperature fuel cell(160℃),exceeding the non-noble-metal catalysts ever reported.The enhancement of activity is attributed to the increasing charge density and poisoning tolerance of Fe–N_(4) caused by neighboring P.This work not only promotes the practical application of Fe-N-C materials in HT-PEMFCs,but also provides a feasible P-doping method for regulating the structure of single atom site.展开更多
基金financially supported by the National Science Foundation of China, China (22179130, 91834301)the Foundation of the Key Laboratory of Chinese Academy of Sciences (CXJJ21S024)Dalian Institute of Chemical Physics, China (DICPI202023)。
文摘Engineering failure of membrane electrode assembly caused by increasingly fuel poisoning in the high temperature polymer electrolyte membrane fuel cells fed with humidified reformate gases is firstly demonstrated herein this work. Based on the results of the in-situ environmental scanning electron microscope, electrochemical analyses, and limiting current method, a water-induced phosphoric acid invasion model is constructed in the porous electrode to elucidate the failure causations of the hindered hydrogen mass transport and the enhanced carbon monoxide poisoning. To optimize the phosphoric acid distribution under the inevitably humidified circumstance, a facile and effective strategy of constructing acid-proofed electrode is proposed and demonstrates outstanding stability with highly humidified reformate gases as anode fuel. This work discusses a potential defect that was rarely studied previously under practical working circumstance for high temperature polymer electrolyte membrane fuel cells, providing an alternative opinion of electrode design based on the fundamental aspects towards the engineering problems.
基金the National Key Research and Development Program of China(No.2018YFA0702002)the Beijing Natural Science Foundation(No.Z210016)the National Natural Science Foundation of China(No.21935001)。
文摘Fe-N-C materials with atomically dispersed Fe–N_(4) sites could tolerate the poisoning of phosphate,is regarded as the most promising alternative to costly Pt-based catalysts for the oxygen reduction in high temperature polymer electrolyte membrane fuel cells(HT-PEMFCs).However,they still face the critical issue of insufficient activity in phosphoric acid.Herein,we demonstrate a P-doping strategy to increase the activity of Fe-N-C catalyst via a feasible one-pot method.X-ray absorption spectroscopy and electron microscopy with atomic resolution indicated that the P atom is bonded with the N in Fe–N_(4) site through C atoms.The as prepared Fe-NCP catalyst shows a half-wave potential of 0.75 V(vs.reversible hydrogen electrode(RHE),0.1 M H_(3)PO_(4)),which is 60 and 40 mV higher than that of Fe-NC and commercial Pt/C catalysts,respectively.More importantly,the Fe-NCP catalyst could deliver a peak power density of 357 mW·cm^(−2)in a high temperature fuel cell(160℃),exceeding the non-noble-metal catalysts ever reported.The enhancement of activity is attributed to the increasing charge density and poisoning tolerance of Fe–N_(4) caused by neighboring P.This work not only promotes the practical application of Fe-N-C materials in HT-PEMFCs,but also provides a feasible P-doping method for regulating the structure of single atom site.