High-performance imidazole-containing polymers for applications in high temperature polymer electrolyte membrane fuel cells

This work focuses on the development of high temperature polymer electrolyte membranes(HT-PEMs)as key materials for HT-PEM fuel cells(HT-PEMFCs).Recognizing the challenges associated with the phosphoric acid(PA) doped polybenzimidazole(PBI) membranes,including the use of carcinogenic monomers and complex synthesis procedures,this study aims to develop more cost-effective,readily synthesized,and high-performance alternatives.A series of superacid-catalyzed polyhydroxyalkylation reactions have been carefully designed between p-terphenyl and aldehydes bearing imidazole moieties,resulting in a new class of HT-PEMs.It is found that the chemical structure of aldehyde-substituted N-heterocycles significantly impacts the polymerization reaction.Specifically,the use of 1-methyl-2-imidazole-formaldehyde and 1 H-imidazole-4-formaldehyde monomers leads to the formation of high-viscosity,rigid,and ether-free polymers,denoted as PTIm-a and PTIm-b.Membranes fabricated from these polymers,due to their pendent imidazole groups,exhibit an exceptional capacity for PA absorption.Notably,PTIm-a,carrying methylimidazole moieties,demonstrates a superior chemical stability by maintaining morphology and structural stability during 350 h of Fenton testing.After being immersed in 75 wt% PA at 40℃,the PTIm-a membrane reaches a PA content of 152%,maintains a good tensile strength of 13.6 MPa,and exhibits a moderate conductivity of 50.2 mS cm^(-1) at 180℃.Under H_(2)/O_(2) operational conditions,a single cell based on the PTIm-a membrane attains a peak power density of 732 mW cm^(-2) at 180℃ without backpressure.Furthermore,the membrane demonstrates stable cycle stability over 173 h within 18 days at a current density of 200 mA cm^(-2),indicating its potential for practical application in HT-PEMFCs.This work highlights innovative strategies for the synthesis of advanced HT-PEMs,offering significant improvements in membrane properties and fuel cell performance,thus expanding the horizons of HT-PEMFC technology.

High temperature treatment induced production of unreduced 2n pollen in Camellia oleifera

Unreduced gametes through chromosome doubling play a major role in the process of plant polyploidization.Our previous work confirmed that Camellia oleifera can produce natural 2n pollen,and it is possible to induce the 2n pollen formation by high temperature treatment.This study focused on the optimization of the 2n pollen induction technique and the mechanisms of high temperature-induced2n pollen formation in C.oleifera.We found that the optimal protocol for inducing 2n pollen via high temperature was to perform 45℃with4 h at the prophaseⅠstage of the pollen mother cells(PMCs).Meanwhile,high temperature significantly decreased the yield and fertility of2n pollen.Through the observation of meiosis,abnormal chromosome and cytological behaviour was discovered under high-temperature treatment,and we confirmed that the formation of 2n pollen is caused by abnormal cell plate.Based on weighted gene co-expression network analysis,fifteen hub genes related to cell cycle control were identified.After male flower buds were exposed to heat shock,polygalacturonase gene(CoPGX3)was significantly upregulated.We inferred that high temperature causes the CoPGX3 gene to be overexpressed and that CoPGX3 is redistributed into the cytosol where it degrades cytoplasmic pectin,which leads to an abnormal cell plate.Furthermore,abnormal cytokinesis resulted in the formation of dyads and triads,and PMCs divided to produce 2n pollen.Our findings provide new insights into the mechanism of 2n pollen induced by high temperature in a woody plant and lay a foundation for further ploidy breeding of C.oleifera.

Sulfonated polybenzimidazole/amine functionalized titanium dioxide(s PBI/AFT) composite electrolyte membranes for high temperature proton exchange membrane fuel cells usage

The novel sulfonated polybenzimidazole(sPBI)/amine functionalized titanium dioxide(AFT) composite membrane is devised and studied for its capability of the application of high temperature proton exchange membrane fuel cells(HT-PEMFCs),unlike the prior low temperature AFT endeavors.The high temperature compatibility was actualized because of the filling of free volumes in the rigid aromatic matrix of the composite with AFT nanoparticles which inhibited segmental motions of the chains and improved its thermal stability.Besides,amine functionalization of TiO2 enhanced their dispersion character in the sPBI matrix and shortened the interparticle separation gap which finally improved the proton transfer after establishing interconnected pathways and breeding more phosphoric acid(PA) doping.In addition,the appeared assembled clusters of AFT flourished a superior mechanical stability.Thus,the optimized sPBI/AFT(10 wt%) showed 65.3 MPa tensile strength;0.084 S·cm^-1 proton conductivity(at 160℃;in anhydrous conditions),28.6% water uptake and PA doping level of 23 mol per sPBI repeat unit.The maximum power density peak for sPBI/AFT-10 met the figure of0.42 W·cm^-2 at 160℃(in dry conditions) under atmospheric pressure with 1.5 and 2.5 stoichiometric flow rates of H2/air.These results affirmed the probable fitting of sPBI/AFT composite for HT-PEMFC applications.

Effects of High Temperature Stress on Microscopic and Ultrastructural Characteristics of Mesophyll Cells in Flag Leaves of Rice

The microscopic and ultrastructural characteristics of mesophyll cells in flag leaves of two rice lines （a thermosensitive line 4628 and a thermo-resistant line 996） under high temperature stress （37℃ during 8：00-17：00 and 30℃ during 17：00-8：00） were investigated using an optical and a transmission electron microscopy. The membrane permeability and malondialdehyde content increased under the high temperature stress, and the increase of both variables was greater in the line 4628 than in the line 996. Under the high temperature stress, the line 996 showed tightly arranged mesophyll cells in flag leaves, fully developed vascular bundles and some closed stomata, whereas the line 4628 suffered from injury because of undeveloped vascular bundles, loosely arranged mesophyll cells and opened stomata. The mesophyll cells in flag leaves of the line 4628 were severely damaged under the high temperature stress, i.e. the chloroplast envelope became blurred, the grana thylakoid layer was arranged loosely and irregularly, the stroma layer disappeared, many osmiophilic granules appeared within the chloroplast, the outer membrane of mitochondria and the nucleus disintegrated and became blurred, the nucleolus disappeared, and much fibrillar-granular materials appeared within the nucleus. In contrast, the mesophyll cells in flag leaves of the line 996 maintained an intact ultrastructure under the high temperature stress. From these results, it is suggested that the ultrastructural modification of the cell membrane system is the primary plant response to high temperature stress and can be used as an index to evaluate the crop heat tolerance.

Cubic anvil cell apparatus for high-pressure and low-temperature physical property measurements

We will build a cubic anvil cell （CAC） apparatus for high-pressure and low-temperature physical property measurements in the synergic extreme condition user facility （SECUF）. In this article, we first introduce the operating principle, the development history, and the current status of the CAC apparatus, and subsequently describe the design plan and technical targets for the CAC in SECUF. We will demonstrate the unique advantages of CAC, i.e., excellent pressure homogeneity and large hydrostatic pressure capacity, by summarizing our recent research progresses using CAC. Finally, we conclude by providing some perspectives on the applications of CAC in the related research fields.

Water-induced electrode poisoning and the mitigation strategy for high temperature polymer electrolyte membrane fuel cells

Engineering failure of membrane electrode assembly caused by increasingly fuel poisoning in the high temperature polymer electrolyte membrane fuel cells fed with humidified reformate gases is firstly demonstrated herein this work. Based on the results of the in-situ environmental scanning electron microscope, electrochemical analyses, and limiting current method, a water-induced phosphoric acid invasion model is constructed in the porous electrode to elucidate the failure causations of the hindered hydrogen mass transport and the enhanced carbon monoxide poisoning. To optimize the phosphoric acid distribution under the inevitably humidified circumstance, a facile and effective strategy of constructing acid-proofed electrode is proposed and demonstrates outstanding stability with highly humidified reformate gases as anode fuel. This work discusses a potential defect that was rarely studied previously under practical working circumstance for high temperature polymer electrolyte membrane fuel cells, providing an alternative opinion of electrode design based on the fundamental aspects towards the engineering problems.

Double Side Interfacial Optimization for Low-Temperature Stable CsPbI_(2)Br Perovskite Solar Cells with High Efficiency Beyond 16%

CsPbI_(2)Br perovskite solar cells have achieved rapid development owing to their exceptional optoelectronic properties and relatively outstanding stability.However,open-circuit voltage(Voc)loss caused by band mismatch and charge recombination between perovskite and charge transporting layer is one of the crucial obstacles to further improve the device performance.Here,we proposed a bilayer electron transport layer ZnO(bottom)/SnO_(2)(top)to reduce the Voc loss(Eloss)and promote device Voc by ZnO insert layer thickness modulation,which could improve the efficiency of charge carrier extraction/transfer and suppress the charge carrier recombination.In addition,guanidinium iodide top surface treatment is used to further reduce the trap density,stabilize the perovskite film and align the energy levels,which promotes the fill factor,short-circuit current density(Jsc),and stability of the device.As a result,the champion cell of double-side optimized CsPbI_(2)Br perovskite solar cells exhibits an extraordinary efficiency of 16.25%with the best Voc as high as 1.27 V and excellent thermal and storage stability.

Performance Investigation of Membrane Electrode Assemblies for High Temperature Proton Exchange Membrane Fuel Cell

Different types of ABPBI (poly(2,5-benzimidazole)) membranes and polymer binders were evaluated to investigate the performance of MEAs for high temperature proton exchange membrane fuel cell (HT-PEMFC). The properties of the prepared MEAs were evaluated and analyzed by polarization curve, electrochemistry impedance spectroscopy (EIS), cyclic voltammetry (CV) and durability test. The results showed that MEA with modified ABPBI membrane (AM) has satisfactory performance and durability for fuel cell application. Compare to conventional PBI or Nafion binders, polytetrafluoroethylene (PTFE) and polyvinylidene difluoride (PVDF) are more attractive as binders in the catalyst layer (CL) of gas diffusion electrode (GDE) for HT-PEMFC.

Effect of High Temperature on Sucrose Content and Sucrose Cleaving Enzyme Activity in Rice Grain During the Filling Stage

Dynamic changes of sucrose, fructose, glucose contents and differences in activities of sucrose synthase, vacuolar invertase, and cell wall bound invertase in rice grain after flowering stage were studied under natural and high temperatures by using two japonica rice varieties Koshihikari and Sasanishiki. In rice grains, the sucrose synthase activity was higher than that of invertase, which was significantly correlated with starch accumulation rate, indicating that the sucrose synthase played an important role in sucrose degradation and starch synthesis. Under high temperature, the significant increase in grain sucrose content without any increase in fructose and glucose contents, suggested that the high temperature treatment enhanced sucrose accumulation, while diminished sucrose degradation in rice grains. Compared with the control plants, the decrease in activities of sucrose synthase, vacuolar invertase, and cell wall bound invertase with high temperature treated plants indicated that the deceleration of sucrose-degradation was related to the decrease in activities of sucrose synthase and invertase.

Numerical Analysis of Temperature Distributions in Single Cell of Polymer Electrolyte Fuel Cell when Operated in Elevated Temperature Range

Abstract： The purpose of this study is to analyze the temperature distribution on the interface between the polymer electrolyte membrane and catalyst layer at the cathode in single cell of polymer electrolyte fuel cell when operated in elevated temperature range than usual. In this study, the interface between the polymer electrolyte membrane and catalyst layer at the cathode is named as reaction surface. This study has considered the 1D multi-plate heat transfer model estimating the temperature distribution on the reaction surface and verified with the 3D numerical simulation model solving many governing equations on the coupling phenomena of the polymer electrolyte fuel cell. The 3D numerical simulation model coverers a half size of actual cell including three straight parts and two turn-back corners, which can display the essential phenomena of single cell. The results from both models/simulations agreed well. The effects of initial operation temperature, flow rate, and relative humidity of supply gas on temperature distribution on the reaction surface have been investigated. Though the effect of flow rate of supply gas on temperature distribution on reaction surface has been small, low relative humidity of supply gas has caused higher temperature on the reaction surface compared to high relative humidity of the supply gas. The temperature rise of reaction surface from initial operation temperature has increased with the increasing in initial operation temperature of cell.

Thermodynamic Foundation for High Temperature Electrochemistry

Thermodynamic concepts required for the thermodynamic calculation of the potentials of electrodes for high temperature applications are briefly reviewed. A thermodynamic approach to the calculation of half cell potentials and the standard chemical potential of an electron at high temperatures which are related to the Standard Hydrogen Electrode(SHE) is discussed. As examples, an external Ag/AgCl reference electrode and a YSZ(Ag|O_2) pH sensor for high temperature applications are analyzed by using the thermodynamic approach to derive a high temperature pH measurement equation. The two electrodes are employed to measure high temperature pH and the measured pH was compared with the calculated pH by using a solution chemistry method. Concepts and principles for electrode kinetics are also briefly introduced and a modification to the Tafel equations is suggested.

Impact of Separator Thickness on Temperature Distribution in Single Polymer Electrolyte Fuel Cell Based on 1D Heat Transfer

It is known from the New Energy and Industry Technology Development Organization (NEDO) roam map Japan, 2017 that the polymer electrolyte fuel cell (PEFC) power generation system is required to operate at 100°C for application of mobility usage from 2020 to 2025. This study aims to clarify the effect of separator thickness on the distribution of the temperature of reaction surface (Treact) at the initial temperature of cell (Tini) with flow rate, relative humidity (RH) of supply gases as well as RH of air surrounding cell of PEFC. The distribution of Treact is estimated by means of the heat transfer model considering the H2O vapor transfer proposed by the authors. The relationship between the standard deviation of Treact-Tini and total voltage obtained in the experiment is also investigated. We can know the effect of the flow rate of supply gas as well as RH of air surrounding cell of PEFC on the distribution of Treact-Tini is not significant. It is observed the wider distribution of Treact-Tini provides the reduction in power generation performance irrespective of separator thickness. In the case of separator thickness of 1.0 mm, the standard deviation of Treact-Tini has smaller distribution range and the total voltage shows a larger variation compared to the other cases.

Shock temperature and reflectivity of precompressed H2O up to 350 GPa:Approaching the interior of planets

Using a combination of static precompression and laser-driven shock compression, shock temperature and reflectivity of H2O have been measured up to 350 GPa and 2.1×10~4 K. Here, two calibration standards were applied to enhance temperature measurement reliability. Additionally, in temperature calculations, the discrepancy in reflectivity between active probe beam wavelength and self-emission wavelength has been taken into account to improve the data’s precision.Precompressed water’s temperature–pressure data are in very good agreement with our quantum molecular dynamics model,suggesting a superionic conductor of H2O in the icy planets’ deep interior. A sluggish slope gradually approaching Dulong–Petit limit at high temperature was found at a specific heat capacity. Also, high reflectivity and conductivity were observed at the same state. By analyzing the temperature–pressure diagram, reflectivity, conductivity and specific heat comprehensively at conditions simulating the interior of planets in this work, we found that as the pressure rises, a change in ionization appears; it is supposedly attributed to energetics of bond-breaking in the H2O as it transforms from a bonded molecular fluid to an ionic state. Such molecular dissociation in H2O is associated with the conducting transition because the dissociated hydrogen atoms contribute to electrical properties.

The effect of grafted alkyl side chains on the properties of poly(terphenyl piperidinium) based high temperature proton exchange membranes

High temperature proton exchange membrane fuel cells(HT-PEMFCs)operating at elevated temperatures above 120℃ take advantage of feasible anode fuels and simplified water/heat management.A high temperature polymer electrolyte membrane(HT-PEM)is the core material for HT-PEMFCs.In this work,a series of phosphoric acid(PA)doped HT-PEMs based on poly(terphenyl piperidine)(PTP)tailored with alkyl groups are synthesized.Five different pendant alkyl groups(including methyl,propyl,pentyl,heptyl and decyl)are grafted onto the piperidine group through the Menshutkin reaction between PTP and alkyl halides.Compared with PTP and methyl grafted PTP(PTP-C1)membranes,the PTP-Cx membranes with long alkyl side chains exhibit improved PA doping contents and conductivities.The optimized pentylsubstituted PTP membrane(PTP-C5)possessed a reasonable PA doping content(202%after immersing in 85 wt%PA at 60℃),high proton conductivity(96 mS cm^(-1) at 180℃)and good tensile strength(4.6 MPa at room temperature).A H_(2)–air single cell equipped with PTP-C5/PA consequently achieved a high peak power density of 676 mW cm^(-2) at 210℃ without any humidification or backpressure.Thus,this work provides a simple method for preparing high-performance HT-PEMs.

Laser-Heated Diamond-Anvil Cell (LHDAC) in Materials Science Research

Laser-heated diamond-anvil cell (LHDAC) is emerging as the most suitable, economical and versatile tool for the measurement of a large spectrum of physical properties of materials under extreme pressure and temperature conditions. In this review, the recent developments in the instrumentation, pressure and temperature measurement techniques, results of experimental investigations from the literature were discussed. Also, the future scope of the technique in various avenues of science was explored.

Phosphorus induced activity-enhancement of Fe-N-C catalysts for high temperature polymer electrolyte membrane fuel cells

Fe-N-C materials with atomically dispersed Fe–N_(4) sites could tolerate the poisoning of phosphate,is regarded as the most promising alternative to costly Pt-based catalysts for the oxygen reduction in high temperature polymer electrolyte membrane fuel cells(HT-PEMFCs).However,they still face the critical issue of insufficient activity in phosphoric acid.Herein,we demonstrate a P-doping strategy to increase the activity of Fe-N-C catalyst via a feasible one-pot method.X-ray absorption spectroscopy and electron microscopy with atomic resolution indicated that the P atom is bonded with the N in Fe–N_(4) site through C atoms.The as prepared Fe-NCP catalyst shows a half-wave potential of 0.75 V(vs.reversible hydrogen electrode(RHE),0.1 M H_(3)PO_(4)),which is 60 and 40 mV higher than that of Fe-NC and commercial Pt/C catalysts,respectively.More importantly,the Fe-NCP catalyst could deliver a peak power density of 357 mW·cm^(−2)in a high temperature fuel cell(160℃),exceeding the non-noble-metal catalysts ever reported.The enhancement of activity is attributed to the increasing charge density and poisoning tolerance of Fe–N_(4) caused by neighboring P.This work not only promotes the practical application of Fe-N-C materials in HT-PEMFCs,but also provides a feasible P-doping method for regulating the structure of single atom site.

Research of special carbon nanobeads supported Pt catalyst for fuel cell through high temperature pyrolysis and deposition from novel phthalocyanine

The carbon nanobeads were prepared through high temperature pyrolysis and deposition from phthalocyanine. After surface's functionalization treatment of the carbon beads, the carbon nanobeads supported Pt catalyst was produced. The Pt/C catalyst was characterized by SEM, TEM, Raman spectrum, EDS and XRD methods. Combining the carbonaceous paper spreaded up with the catalyst with Nafion membrane, we made MEA electrode. The discharge curves indicated that this carbon nanobeads supported Pt is a good fuel cell catalyst with excellent performance, high activity and sign of a long-time life.

Pc-Si and c-Si Cell Studies at Transient and Steady State Conditions in Various Illumination Levels

A set of experiments was designed to study the power performance of a c-Si and a pc-Si cell when exposed to various levels of high illumination. The light concentration ratio, C, ranges from C 〈 1, up to C ≈ 26. An experimental set up was built for the purposes of this project. PV cell modeling is outlined in this paper for isc, Voc and the PV cell temperature, Tc, which predicts those quantities. There the behaviour of the two PV-cells at both transient out steady state conditions is studied. Predicted values are compared against measured ones. A comparison of the experimental values against the theoretically predicted ones is performed for the range C 〈 1 to C ≈ 26. Power recovery is tried through heat removal from both sides of the PV-cells by air forced flow. Experiments show recovery whose degree is close to 100% for low C values. On the other hand, as C grows higher, P~ starts decreasing too. PV cell temperatures reached up to 136 ℃ for C = 25. This is a challenge as reduction of temperature delivers a good amount of heat, in the cogeneration effect, while it has a positive impact to power recovery of the PV cell.

Survey of Intracellular Protein Extraction Methods from Pichia pastoris

The broken efficiency of cell wall and the release amount of Pichia pastoris intracellular protein under different cell breaking conditions were investigated in this paper. The results showed that broken efficiency using hot alkali combined with high-pressure homogenizing method was higher than that of enzyme hydrolysis, hot alkali treatment and high-pressure homogenation, respectively. Suspended medium had little effect on the broken efficiency of yeast cell, but had significant effect on the protein release yield. The results indicated that optimal condition for intracellular proteins extraction was 30% (wet weight, w/v) of yeast cells suspend in 50 mM phosphate buffer (pH 10.0), water bathed at 60?C for 2 hours, homogenized twice at 100 MPa pressure. The broken efficiency of Pichia pastoris cell could reach 87.6% and the protein yield was 35.48 g per 100 g cells.

Modeling of Packed Bed Methanol Steam Reformer Integrated with Tubular High Temperature Proton Exchange Membrane Fuel Cell

This work proposes a novel tubular structure of high-temperature proton exchange membrane fuel cell(PEMFC)integrated with a built-in packed-bed methanol steam reformer to provide hydrogen for power output.A two-dimensional axisymmetric non-isothermal model was developed in COMSOL Multiphysics 5.4 to simulate the performance of a tubular high temperature proton membrane fuel cell and a packed bed methanol reformer.The model considers the coupling multi-physical processes,including methanol reforming reaction,water gas shift reaction,methanol cracking reaction as well as the heat,mass and momentum transport processes.The sub-model of the tubular packed-bed methanol reformer is validated between 433 K and 493 K with the experimental data reported in the literature.The sub-model of the high temperature proton exchange fuel cell is validated between 393 K and 433 K with the published literature.Our results show that power output and temperature distribution of the integrated unit depend on methanol flow rates and working voltages.It was suggested that stable power generation performance of 0.14 W/cm_(2)and temperature drop in methanol steam reformer of≤10 K could be achieved by controlling the methanol space-time ratio of≥250 kg·s/mol with working voltage at 0.6 V,even in the absence of an external heat source.