Microstructure and property of bearing steel with and without nitrogen addition were investigated by microstructural observation and hardness measurement after different heat treatment processing. Based on the microst...Microstructure and property of bearing steel with and without nitrogen addition were investigated by microstructural observation and hardness measurement after different heat treatment processing. Based on the microstructural observation of both 9Cr18 steel and X90N steel, it was found that nitrogen addition could effectively reduce the amount and size of coarse carbides and also refine the original austenite grain size. Due to addition of nitrogen, more austenite phase was found in X90N steel than in 9Cr18 steel. The retained austenite of X90N steel after quenching at 1050℃ could be reduced from about 60% to about 7 9% by cold treatment at -73℃ and subsequent tempering, and thus finally increased the hardness up to 60 HRC after low temperature tempering and to 63 HRC after high temperature tempering. Furthermore, both the wear and corrosion resistance of X90N steel were found much more superior than those of 9Cr18 steel, which was attributed to the addition of nitrogen. It was proposed at last that nitrogen alloying into the high chromium bearing steel was a promising way not only to refine the size of both carbides and austenite, but also to achieve high hardness, high wear property and improved corrosion resistance of the stainless bearing steel.展开更多
A new ferritic creep resistant steel has been developed by eliminating Nb and adding 1.5 mass % Re to a ferritic steel grade T/P23 with the aim of enhancing its mechanical properties at high temperature.Cast ingots of...A new ferritic creep resistant steel has been developed by eliminating Nb and adding 1.5 mass % Re to a ferritic steel grade T/P23 with the aim of enhancing its mechanical properties at high temperature.Cast ingots of both steels, new grade and ASTM T/P 23, were hot rolled at 900℃ and then submitted to a thermal treatment consisting of solubilization at 1050℃ and tempering at 700℃. Tempered bainitic microstructures obtained contain second phases reinforcing carbide particles, mainly M_6C and M_（23）C_6 at the boundaries of both, prior austenite grains and bainitic ferrite laths, as well as MC within the grains. Mechanical properties at temperatures ranging from 540 to 600℃ were studied by strain-ratechange tests in compression at strain rates between 10^（-7） and 10^（-4）s^（-1）. These tests showed high stress exponents（n ≥ 20） and activation energies（Q ≈ 400 k J/mol） for both alloys, which were associated with a dislocation movement mechanism with a strong interaction between dislocations and precipitates. On the other hand, a creep exponent of 5 was derived for the stress dependence of minimum creep rate from conventional-type creep tests at 600℃. Although this stress exponent is usually related to a dislocation climb controlled creep mechanism, remarkable microstructural degradation observed with increasing creep time makes difficult to elucidate the true deformation mechanism controlling creep.展开更多
基金supported by National Natural Science Foundation of China (51371057)International Project Collaboration between CISRI (P.R.China) and COMTES FHT a.s (Czech Republic)
文摘Microstructure and property of bearing steel with and without nitrogen addition were investigated by microstructural observation and hardness measurement after different heat treatment processing. Based on the microstructural observation of both 9Cr18 steel and X90N steel, it was found that nitrogen addition could effectively reduce the amount and size of coarse carbides and also refine the original austenite grain size. Due to addition of nitrogen, more austenite phase was found in X90N steel than in 9Cr18 steel. The retained austenite of X90N steel after quenching at 1050℃ could be reduced from about 60% to about 7 9% by cold treatment at -73℃ and subsequent tempering, and thus finally increased the hardness up to 60 HRC after low temperature tempering and to 63 HRC after high temperature tempering. Furthermore, both the wear and corrosion resistance of X90N steel were found much more superior than those of 9Cr18 steel, which was attributed to the addition of nitrogen. It was proposed at last that nitrogen alloying into the high chromium bearing steel was a promising way not only to refine the size of both carbides and austenite, but also to achieve high hardness, high wear property and improved corrosion resistance of the stainless bearing steel.
基金supported by the Spanish Ministry of Economy and Competitiveness(MINECO)under Grant MAT2012-39124,MAT2015-68919,and MAT2016-80875
文摘A new ferritic creep resistant steel has been developed by eliminating Nb and adding 1.5 mass % Re to a ferritic steel grade T/P23 with the aim of enhancing its mechanical properties at high temperature.Cast ingots of both steels, new grade and ASTM T/P 23, were hot rolled at 900℃ and then submitted to a thermal treatment consisting of solubilization at 1050℃ and tempering at 700℃. Tempered bainitic microstructures obtained contain second phases reinforcing carbide particles, mainly M_6C and M_（23）C_6 at the boundaries of both, prior austenite grains and bainitic ferrite laths, as well as MC within the grains. Mechanical properties at temperatures ranging from 540 to 600℃ were studied by strain-ratechange tests in compression at strain rates between 10^（-7） and 10^（-4）s^（-1）. These tests showed high stress exponents（n ≥ 20） and activation energies（Q ≈ 400 k J/mol） for both alloys, which were associated with a dislocation movement mechanism with a strong interaction between dislocations and precipitates. On the other hand, a creep exponent of 5 was derived for the stress dependence of minimum creep rate from conventional-type creep tests at 600℃. Although this stress exponent is usually related to a dislocation climb controlled creep mechanism, remarkable microstructural degradation observed with increasing creep time makes difficult to elucidate the true deformation mechanism controlling creep.
