Recent progress in high temperature permanent magnetic materials

Permanent magnetic materials capable of operating at high temperature up to 500℃ have wide potential applications in fields such as aeronautics, space, and electronic cars. SmCo alloys are candidates for high temperature applications, since they have large magnetocrystalline anisotropy field （6-30 T）, high Curie temperature （720-920℃）, and large energy product （〉200 kJ.m-3） at room temperature. However, the highest service temperature of commercial 2：17 type SmCo magnets is only 300℃, and many efforts have been devoted to develop novel high temperature permanent magnets. This review focuses on the development of three kinds of SmCo based magnets： 2：17 type SmCo magnets, nanocrystalline SmCo magnets, and nanocomposite SmCo magnets. The oxidation protection, including alloying and surface modification, of high temperature permanent magnets is discussed as well.

Application of phase diagram calculations to development of new ultra-high temperature structural materials

In-situ refractory metal intermetallic composites(RMICs) based either on (Nb, Si) or (Mo, Si, B) are candidate materials for ultra-high temperature applications (>1400 ℃). To provide a balance of mechanical and environmental properties, Nb-Si composites are typically alloyed with Ti and Cr, and Mo-Si-B composites are alloyed with Ti. Phase diagrams of Nb-Cr-Ti-Si and Mo-Si-B-Ti, as prerequisite knowledge for advanced materials design and processing development, are critically needed. The phase diagrams in the metal-rich regions of multicomponent Nb-Cr-Ti-Si and Mo-Si-B-Ti were rapidly established using the Calphad (Calculation of phase diagram) approach coupled with key experiments. The calculated isotherms, isopleths, and solidification paths were validated by experimental work. The important heterogeneous multiphase equilibria in both quaternary systems identified will offer engineers the opportunity to develop materials with a balance of properties for high-temperature applications.

HIGH TEMPERATURE MATERIALS AND STRENGTH STUDY IN CHINA

In the past half century China has developed and formed her own system ofhigh temperature materials for power, automobile and aero-engine industries in the temperature rangefrom 550 deg C to 1100 deg C. These high temperature materials include heat-resisting steels,iron-base, nickel-iron-base and nickel-base superalloys. Some achievements - in high temperaturestrength study, new technologies and new alloy development are also discussed.

Experimental study of the temporary plugging capability of diverters to block hydraulic fractures in high-temperature geothermal reservoirs

The effective plugging of artificial fractures is key to the success of temporary plugging and diverting fracturing technology,which is one of the most promising ways to improve the heat recovery efficiency of hot dry rock.At present,how temporary plugging agents plug artificial fractures under high temperature remains unclear.In this paper,by establishing an improved experimental system for the evaluation of temporary plugging performance at high temperature,we clarified the effects of high temperature,injection rate,and fracture width on the pressure response and plugging efficiency of the fracture.The results revealed that the temporary plugging process of artificial fractures in hot dry rock can be divided into four main stages:the initial stage of temporary plugging,the bridging stage of the particles,the plugging formation stage,and the high-pressure dense plugging stage.As the temperature increases,the distribution distance of the temporary plugging agent,the number of pressure fluctuations,and the time required for crack plugging increases.Particularly,when the temperature increases by 100℃,the complete plugging time increases by 90.7%.

Quasi-static and low-velocity impact mechanical behaviors of entangled porous metallic wire material under different temperatures

To improve the defense capability of military equipment under extreme conditions,impact-resistant and high-energy-consuming materials have to be developed.The damping characteristic of entangled porous metallic wire materials(EPMWM)for vibration isolation was previously investigated.In this paper,a study focusing on the impact-resistance of EPMWM with the consideration of ambient temperature is presented.The quasi-static and low-velocity impact mechanical behavior of EPMWM under different temperatures(25℃-300℃)are systematically studied.The results of the static compression test show that the damping energy dissipation of EPMWM increases with temperature while the nonlinear damping characteristics are gradually enhanced.During the impact experiments,the impact energy loss rate of EPMWM was between 65%and 85%,while the temperatures increased from 25℃to 300℃.Moreover,under the same drop impact conditions,the overall deformation of EPMWM decreases in the temperature range of 100℃-200℃.On the other hand,the impact stiffness,energy dissipation,and impact loss factor of EPMWM significantly increase with temperature.This can be attributed to an increase in temperature,which changes the thermal expansion coefficient and contact state of the internal wire helixes.Consequently,the energy dissipation mode(dry friction,air damping,and plastic deformation)of EPMWM is also altered.Therefore,the EPMWM may act as a potential candidate material for superior energy absorption applications.

Experimental investigation of high temperature thermal contact resistance with interface material

Thermal contact resistance plays a very important role in heat transfer efficiency and thermomechanical coupling response between two materials,and a common method to reduce the thermal contact resistance is to fill a soft interface material between these two materials.A testing system of high temperature thermal contact resistance based on INSTRON 8874 is established in the present paper,which can achieve 600 C at the interface.Based on this system,the thermal contact resistance between superalloy GH600 material and three-dimensional braid C/C composite material is experimentally investigated,under different interface pressures,interface roughnesses and temperatures,respectively.At the same time,the mechanism of reducing the thermal contact resistance with carbon fiber sheet as interface material is experimentally investigated.Results show that the present testing system is feasible in the experimental research of high temperature thermal contact resistance.

Lost circulation material for abnormally high temperature and pressure fractured-vuggy carbonate reservoirs in Tazhong block, Tarim Basin, NW China

To effectively solve the problem of lost circulation and well kick frequently occurring during the drilling of abnormally high temperature and pressure fractured-vuggy reservoirs in the Tazhong block, a rigid particle material, GZD, with high temperature tolerance, high rigidity(> 8 MPa) and low abrasiveness has been selected based on geological characteristics of the theft zones in the reservoirs. Through static pressure sealing experiments, its dosage when used alone and when used in combination with lignin fiber, elastic material SQD-98 and calcium carbonate were optimized, and the formula of a new type(SXM-I) of compound lost circulation material with high temperature tolerance and high strength was formed. Its performance was evaluated by compatibility test, static sealing experiment and sand bed plugging experiment. The test results show that it has good compatibility with drilling fluid used commonly and is able to plug fractures and vugs, the sealed fractures are able to withstand the static pressure of more than 9 MPa and the cumulative leakage is 13.4 mL. The mud filtrate invasion depth is only 2.5 cm in 30 min when the sand bed is made of particles with sizes between 10 mesh and 20 mesh. Overall, with good sealing property and high temperature and high pressure tolerance, the lost circulation material provides strong technical support for the safety drilling in the block.

Design of the material performance test apparatus for high temperature gas-cooled reactor

Most materials can be easily corroded or ineffective in carbonaceous atmospheres at high temperatures in the reactor core of the high temperature gas-cooled reactor(HTGR).To solve the problem,a material performance test apparatus was built to provide reliable materials and technical support for relevant experiments of the HTGR.The apparatus uses a center high-purity graphite heater and surrounding thermal insulating layers made of carbon fiber felt to form a strong carbon reducing atmosphere inside the apparatus.Specially designed tungsten rhenium thermocouples which can endure high temperatures in carbonaceous atmospheres are used to control the temperature field.A typical experimental process was analyzed in the paper,which lasted 76 hours including seven stages.Experimental results showed the test apparatus could completely simulate the carbon reduction atmosphere and high temperature environment the same as that confronted in the real reactor and the performance of screened materials had been successfully tested and verified.Test temperature in the apparatus could be elevated up to 1600oC,which covered the whole temperature range of the normal operation and accident condition of HTGR and could fully meet the test requirements of materials used in the reactor.

Pt-Al₂OM₃Composite Material Designed for Cyclic Production of Optical Glasses under High Temperature Conditions

The article considers one of the possible approaches to the solution of an urgent issue of metal consumption reduction, increase of operating life and maximum operating temperature as well as reduction of irrecoverable losses of platinum products and alloys when operating under high temperature conditions, particularly for glassblowing and single crystal growing crucibles. A two-layered composite material based on platinum-group metals and corundum plasma ceramics is thoroughly investigated. A successful experience of crucibles exploitation, designed for production of high temperature optical glasses from the composite and results of the research on composite material specimens are described.

A waveform modification method for testing dynamic properties of rock under high temperature

In this study,a waveform modification method was proposed using a self-designed heating device combined with the split Hopkinson pressure bar(SHPB)technique for determination of dynamic behaviors of rock at high temperature.Firstly,the temperature gradient distribution on the incident bar was measured according to the variation of elastic modulus of the bar with temperature,and the relationship between the longitudinal wave velocity and temperature of the bar was obtained based on onedimensional stress wave theory.The incident bar with a temperature gradient was divided into a series of microelements,and then the transmission coefficient of the whole incident bar was obtained.Finally,the stress wave was modified by the transmission coefficient from 25℃ to 600℃.This method was used to study the dynamic properties of rock at high temperature,which not only preserves a classical SHPB device,but also effectively ensures the accuracy of the experimental results.A dynamic Brazilian disc experiment was carried out to explore the influences of loading rate and temperature on dynamic tensile strength of sandstone at high temperature using the proposed waveform modification method.

High Temperature Performances of Spherical Nickel Hydroxide with Additive Y_2O_3

The effect Of Y2O3 as additive to the positive electrode on the high-temperature performances of the Ni-MH batteries was studied. The specific capacities of the positive electrode in Ni-MH battery at higher temperatures are much lower than usual. In order to improve high-temperature performances, charge/discharge curves of the Ni(OH)(2) electrodes with different amounts Of Y2O3 it different temperatures were studied. It is found that the specific capacities of the spherical Ni (OH)(2) with Y2O3 as additive are much higher than those of the regular at higher temperatures. The specific capacity of Ni (OH)(2) containing 1% Y2O3 at 0.2C C/D rate is 35% higher than that of the regular. The specific capacity of Ni (OH)(2) containing 0.2% Y2O3 at 1C C/D rate is 15% higher than that of the regular. Mechanism Of Y2O3 improving high temperature performances of Ni(OH)(2) electrode was also discussed in detail.

Strengthening Mullite Ceramic Materials by Gas Infiltration

In order to improve the high-temperature performance of mullite ceramic materials,mullite ceramic bodies were placed in closed containers with AlF_(3)·3H_(2)O powder and kept at 1 600 ℃ for 6 h.AlF_(3)·3H_(2)O reacts with O_(2) to produce gaseous compounds AlOF and F,which penetrate into the bodies,promote Al2O3 and SiO_(2) to form mullite whiskers,and strengthen the mullite ceramic materials.The results show that the mullite ceramics have enhanced hot strength,increased bulk density and declined apparent porosity by adding a certain amount of AlF_(3)·3H_(2)O in a closed container.When the addition of AlF_(3)·3H_(2)O is 6%,the bulk density of the ceramic material reaches the maximum and the apparent porosity is the lowest;and when the addition of AlF_(3)·3H_(2)O is 8%,the hot strength of the material is the highest.

Research progress of high temperature resistant nylon 10T

Researches about synthesis and modification of nylon 10T(PA10T)in domestic universities and scientific research institutions are reviewed in this paper.The results show that,due to the different performance requirements,PA10T is studied from the co-polymerization,blending modification and filling modification of these three aspects.Meanwhile,the existing problems are analyzed and the development prospect of PA10T is predicted.

Mechanical Properties with High Temperature and the Microstructure of Carbon/Phenolic Ablative Composites

Carbon fiber reinforced phenolic based composites were prepared by laminating molding. The variation in mechanical characteristics of composites was evaluated with heating temperature and procedure. The microstructures of composites at different temperatures were observed by optical microscope and scanning electron microscope, respectively. The results showed that the main weight loss range of carbon/phenolic is from 300 to 800 ℃, before 700 ℃ the weight loss was resulted from pyrolysis and after that the weight loss was mainly by oxidation in the fiber phase; with the heat treatment temperature rising, the bonding at the interface of carbon fibers and resin matrix weakened; in the pyrolysis temperature range, the interlaminar shear strength（ILSS） of carbon/phenolic showed a rapid drop with temperature rising, and then decrease in the rate of ILSS became relatively slower; the fiber oxidation had little influence on the ILSS.

Flexural behavior of composite beams after the ultimate limit state externally strengthened with CFRP sheets bonded with high-temperature resistant matrix

In this paper the alkali-activated slag cementitious materials(AASCM)which strength at 600 ℃ is larger than that of AASCM at room temperature,were prepared to paste CFRP sheets to strengthen four simply supported unbonded prestressed composite beams encased circular steel tube truss after ultimate limit state.Test on flexural behavior of these four beams was performed.Moreover,normal section load-bearing capacity of these beams and the curve load-deflection at mid-span were obtained.Experimental results show that it is feasible to strengthen concrete members with CFRP sheets bonded with AASCM.Based on the experimental results and theoretical study,computational method of stiffness is proposed for calculating bending rigidity and normal section load-bearing capacity of concrete simply supported beams strengthened with CFRP sheets bonded with AASCM.Formula of bending rigidity calculation was founded which results are in good agreement with testing data.

Early Intervention on the Properties of Steel Slag at High Temperature by Modifier Compound with Tailings: A Feasible Way for Comprehensive Utilization of Solid Wastes

Steel slag, a by-product of the steel production industry reaches 10%–15% of crude steel output (Motz and Geiseler, 2001). Their main application lies in the field of building materials due to some containing cementitious components, such as dicalcium silicate (C2S) and tricalcium silicate (C3S) (Waligora et al., 2010). However, blended cements with steelmaking slag show low early hydration activity, low compressive strength and bad durability because steel slag generates above 1600 ℃ with the tense and large grain size crystals, consisting of low content of C2S and C3S and high proportions of f-CaO and f-MgO compared with cement clinker.

High temperature geothermal drilling mud

ＨＩＧＨＴＥＭＰＥＲＡＴＵＲＥＧＥＯＴＨＥＲＭＡＬＤＲＩＬＬＩＮＧＭＵＤＴａｎｇＳｏｎｇｒａｎ，ＴａｏＳｈｉＸｉａｎＩｎｓｔｉｔｕｔｅｏｆＥｘｐｌｏｒａｔｉｏｎＥｎｇｉｎｅｅｒｉｎｇ，Ｂｅｉｊｉｎｇ１０２４０５，ＣｈｉｎａＨＩＧＨＴＥＭＰＥＫＡＴＵＲ...

Effects of mechanical boundary conditions on thermal shock resistance of ultra-high temperature ceramics

The effects of mechanical boundary conditions, often encountered in thermalstructural engineering, on the thermal shock resistance（TSR） of ultra-high temperature ceramics（UHTCs） are studied by investigating the TSR of a UHTC plate with various types of constraints under the first, second, and third type of thermal boundary conditions. The TSR of UHTCs is strongly dependent on the heat transfer modes and severity of the thermal environments. Constraining the displacement of the lower surface in the thickness direction can significantly decrease the TSR of the UHTC plate, which is subject to the thermal shock at the upper surface. In contrast, the TSR of the UHTC plate with simply supported edges or clamped edges around the lower surface is much better.

High-temperature tribological performance of functionally graded Stellite 6/WC metal matrix composite coatings manufactured by laser-directed energy deposition

Wear-driven tool failure is one of the main hurdles in the industry.This issue can be addressed through surface coating with ceramic-reinforced metal matrix composites.However,the maximum ceramic content is limited by cracking.In this work,the tribological behaviour of the functionally graded WC-ceramic-particlereinforced Stellite 6 coatings is studied.To that end,the wear resistance at room temperature and 400°C is investigated.Moreover,the tribological analysis is supported by crack sensitivity and hardness evaluation,which is of utmost importance in the processing of composite materials with ceramic-particle-reinforcement.Results indicate that functionally graded materials can be employed to increase the maximum admissible WC content,hence improving the tribological behaviour,most notably at high temperatures.Additionally,a shift from abrasive to oxidative wear is observed in high-temperature wear testing.

Elevated temperature endurance and creep properties of extruded 2D70 Al alloy rods

The elevated temperature performances of 2D70 Al alloy hot extrusion rods after two-stage homogenization and intensive deformation were studied by measuring the elevated temperature enduring strength and the creep ultimate strength. The fracture morphology of some selected samples after testing at different elevated temperatures was observed by scanning electron microscopy （SEM）. The results indicate that, as the test temperature increases, the elevated temperature enduring strength of 2D70 Al alloy decreases gradually. In a comparison between 150 C and 240 C, the notch enduring strength drops from 375 to 185 MPa and the smooth enduring strength drops from 337 to 130 MPa. Enduring strength is not sensitive to the notch. The notch sensitivity ratio （NSR） coefficient is in the range of 1.119 to 1.423 from 150 C to 240 C. The creep test results show that, as the test temperature increases from 150 C to 240 C, the creep ultimate strength of 2D70 Al alloy rods drops gradually from 312 to 117 MPa.