In this paper the relationship between microstructure and stress-strain behavior in tensile test of high strength pipeline steel was investigated.The steel with polygonal ferrite-bainite(PF + B) microstructure has a &...In this paper the relationship between microstructure and stress-strain behavior in tensile test of high strength pipeline steel was investigated.The steel with polygonal ferrite-bainite(PF + B) microstructure has a "round-house" type tensile stress-strain curve with low Y/T ratio,highly uniform elongation and high n-value,which means PF + B microstructure has the best deformability(i.e.Ideal stress-strain behavior) among the four microstructures.The steel with acicular ferrite-martensite&austenite(AF + MA) microstructure has a "continuous-yielding" type tensile stress-strain curve,whose deformability is worse than that of PF + B microstructure.Both the steels of polygonal ferrite-acicular ferrite(PF + AF) and polygonal ferrite-pearlite (PF+P) microstructure have "luders elongation" type tensile stress-strain curve with high Y/T ratio,low uniform elongation and low n-value,which means PF + AF and PF + P microstructures have the worst deformability among the four microstructures.展开更多
A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinfo...A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinforced concrete （SFRC） under uniaxial tension were studied experimentally. When the matrix strength and the fiber content increase, the tensile stress and tensile strain vary differently according to the fiber type. The mechanisms of reinforcing effect for different types of fiber were analyzed and the stress-strain curves of the specimens were plotted. Some experimental factors for stress or strain of SFRC were given. A tensile toughness modulus Re0.5 was introduced to evaluate the toughness characters of SFRC under uniaxial tension. Moreover, the formula of the tensile stress-strain curve of SFRC was regressed. The theoretical curve and the experimental ones fit well, which can be used for references in construction.展开更多
Reliable dynamic mechanical properties of high nitrogen steels are necessary for the design and assessment of armor structures subject to impact and blast. A series of experiments, based on Hopkinson bar techniques, w...Reliable dynamic mechanical properties of high nitrogen steels are necessary for the design and assessment of armor structures subject to impact and blast. A series of experiments, based on Hopkinson bar techniques, were conducted and described in this study. The dynamic compression, tensile and shear properties of high nitrogen steel had been tested, and the stress-strain curves under high strain rates were obtained. The results have been showed as follows: High nitrogen steel has a remarkable strain rate strengthening effect. Compared to the static curves, the constitutive curves of dynamic tension and compression move upper. The dynamic compressive yield strength of high nitrogen steel increases first and then decreases with the increase of strain rate, and the yield strength varies in the range of 1465-1549 MPa within the range of 1147-2042 s^(-1) strain rate; The tensile strength of high nitrogen steel increases with the increase of strain rate. When the strain rate is greater than 1341 s^(-1), the tensile strength will not increase and the curve tends to be gentle. The pure shear yield strength of the high nitrogen steel is above 800 MPa.展开更多
文摘In this paper the relationship between microstructure and stress-strain behavior in tensile test of high strength pipeline steel was investigated.The steel with polygonal ferrite-bainite(PF + B) microstructure has a "round-house" type tensile stress-strain curve with low Y/T ratio,highly uniform elongation and high n-value,which means PF + B microstructure has the best deformability(i.e.Ideal stress-strain behavior) among the four microstructures.The steel with acicular ferrite-martensite&austenite(AF + MA) microstructure has a "continuous-yielding" type tensile stress-strain curve,whose deformability is worse than that of PF + B microstructure.Both the steels of polygonal ferrite-acicular ferrite(PF + AF) and polygonal ferrite-pearlite (PF+P) microstructure have "luders elongation" type tensile stress-strain curve with high Y/T ratio,low uniform elongation and low n-value,which means PF + AF and PF + P microstructures have the worst deformability among the four microstructures.
基金Funded by Regulation RevisingItemof China Associationfor En-gineering Construction Standardization (CECS 15 :2000)
文摘A whole of 110 specimens divided into 22 groups were tested with varying the volume fraction of steel fibers and the matrix strength of these specimens. The stress-strain behaviors of four types of steel fiber reinforced concrete （SFRC） under uniaxial tension were studied experimentally. When the matrix strength and the fiber content increase, the tensile stress and tensile strain vary differently according to the fiber type. The mechanisms of reinforcing effect for different types of fiber were analyzed and the stress-strain curves of the specimens were plotted. Some experimental factors for stress or strain of SFRC were given. A tensile toughness modulus Re0.5 was introduced to evaluate the toughness characters of SFRC under uniaxial tension. Moreover, the formula of the tensile stress-strain curve of SFRC was regressed. The theoretical curve and the experimental ones fit well, which can be used for references in construction.
文摘Reliable dynamic mechanical properties of high nitrogen steels are necessary for the design and assessment of armor structures subject to impact and blast. A series of experiments, based on Hopkinson bar techniques, were conducted and described in this study. The dynamic compression, tensile and shear properties of high nitrogen steel had been tested, and the stress-strain curves under high strain rates were obtained. The results have been showed as follows: High nitrogen steel has a remarkable strain rate strengthening effect. Compared to the static curves, the constitutive curves of dynamic tension and compression move upper. The dynamic compressive yield strength of high nitrogen steel increases first and then decreases with the increase of strain rate, and the yield strength varies in the range of 1465-1549 MPa within the range of 1147-2042 s^(-1) strain rate; The tensile strength of high nitrogen steel increases with the increase of strain rate. When the strain rate is greater than 1341 s^(-1), the tensile strength will not increase and the curve tends to be gentle. The pure shear yield strength of the high nitrogen steel is above 800 MPa.
