Green evaluation of microwave-assisted leaching process of high titanium slag on life cycle assessment

A greenness evaluation index and system of microwave-assisted leaching method were established.The effects of the life cycle assessment variables,such as the resource consumption,environment impact,cost,time and quality,were investigated,and the concept of green degree was applied in the production of synthetic rutile.An analytic hierarchy process was utilized to assess matrix of greenness evaluation.The Gauss-Seidel iterative matrix method was employed to solve the assessment matrix and obtain the weights and membership functions of all evaluation indexes.A fuzzy decision-making method was applied to build the greenness evaluation model,and then the scores of green degree in microwave-assisted leaching process was obtained.The greenness evaluation model was applied to the life cycle assessment of the microwave-assisted leaching process.The results show that the microwave-assisted leaching process has advantages over the conventional ones,with respect to energy-consumption,processing time and environmental protection.

Microwave absorbing properties of high titanium slag

Microwave absorbing properties of high titanium slag were investigated by using microwave cavity perturbation technique. High titanium slag containing more than 90% TiO2 was prepared by carbothermal reduction of ilmenite. The temperature rise curve of high titanium slag in microwave heating process was obtained. Crystalline compounds of high titanium slag before and after microwave irradiation were obtained and characterized by X-ray diffractometry (XRD). Effects of particle size of high titanium slag and mixtures of high titanium slag with different mass fractions of V2O5 on microwave absorbing properties were investigated systematically. The results show that high titanium slag has good microwave absorption property; untreated high titanium slag mainly consists of crystalline compounds of anatase and iron titanium oxide, while the microwave-irradiation treated one is mainly composed of crystalline compounds of rutile and iron titanium oxide. Synthetic anatase is transformed completely into rutile at about 1 050 ℃ for 20 min under microwave irradiation. High frequency shift and low amplitude of voltage make high titanium slag an ideal microwave absorbent. 180 μm of particle size and 10% mass fraction of V2O5 are found to be the optimum conditions for microwave absorption.

Recovery of titania from high titanium slag by roasting method using concentrated sulfuric acid

By means of energy-dispersive X-ray spectroscopy (EDX) and scanning electron microscope (SEM) analysis, the phase structure characteristics of high titanium slag were analyzed. Through the single factor and the orthogonal experiment methods, the effects of material particle size, mass ratio of acid to ore, roasting temperature, and roasting time on the acidolysis ratio of TiO2 during the process of roasting high titanium slag with concentrated sulfuric acid were systematically investigated. The results show that the sequence of each factor affecting the acidolysis ratio of TiO2 is: mass ratio of acid to ore, roasting time, and roasting temperature. The optimum technological conditions are obtained as mass ratio of acid to ore of 2.1, roasting temperature of 310°C, roasting time of 75min, and material particle size of 45–53μm. The acidolysis ratio of TiO2 is over 96% under the optimum conditions. The roasting process is proved to be significant in the exploitation and utilization of high titanium slag. The advantages of the proposed roasting process are of high efficiency, low power consumption, and minimum pollution.

Thermodynamic analysis of production of high purity titanium by thermal decomposition of titanium iodide

High purity titanium was prepared by thermal decomposition of titanium iodide.The feasible synthetic route and optimum decompositon temperaure were obtained by thermodynamic analysis in the process of thermal decomposition of titanium iodide and nucleation growth theory.The temperature for the formation of titanium iodide is in the range of 800-900 K,at which a large amount of titanium iodide vapour can be obtained.The decomposition temperature of titanium iodide is in the range of 1 300-1 500 K,at which a favourable decomposition rate can be achieved.The experiment results show that the purity of the produced titanium is more than 99.995%.

Sulfur distribution in preparation of high titanium ferroalloy by thermite method with different CaO additions

Ferrotitanium is used as a deoxidizer and alloying agent during steelmaking process,which has a high demand for sulfur control.Sulfur was introduced from raw materials in the process of producing ferrotitanium by thermite method,where CaO was used as fluxing agent.At the same time,CaO has a great desulfurization capability.Effects of CaO addition on the distribution of sulfur in high titanium ferroalloy prepared by thermite method were studied in this work.The equilibrium diagram of Ti-AlFe-S system was calculated by FactSage 6.4 software package with FactPS and FTmisc database.The alloy and slag samples were characterized by X-ray diffraction(XRD),scanning electron microscopy(SEM),inductively coupled plasma atomic emission spectrometer(ICP-AES),X-ray fluorescence(XRF)and high-frequency infrared ray carbon sulfur analyzer.The result indicates that the sulfur in the alloy firstly exists in the form of liquid FeS,thereafter TiS(s)and eventually Ti2 S(s)during cooling.The sulfur is mainly distributed in the alloy,and only a small amount of sulfur remains in the slag.Moreover,it is noted that the sulfur in the alloy does not distribute homogeneously,and it exists in the form of solid solution phase,(Ti,Al,Fe)S.S content in the slag,the sulfur capacity of the slag and the sulfur distribution ratio(LS)all increase with the increment of CaO addition,while S content in alloys decreases.

Evaluation of Oxidation of Ti-Al and Ti-Al-Cr Coatings Arc-ion Plated on Ti-60 High-temperature Titanium Alloy

High-temperature titanium alloy for aeroengine compressor applications suffers from high-temperature oxidation and environmental corrosion, which prohibits long-term service of this kind alloy at temperatures above 600℃. In an attempt to tackle this problem, Ti-48Al （at. pct） and Ti-48Al-12Cr （at. pct） protective coatings were plated on the substrate of alloy Ti-60 by arc ion plating （ALP） method. Isothermal and cyclic oxidation tests were performed in static air at elevated temperatures. Phase composition, morphology of the coatings and distribution of elements were investigated by X-ray diffraction （XRD）, scanning electron microscopy （SEM） and energy dispersive X-ray analysis （EDX）. The results showed that the Ti-48Al coating exhibited good isothermal oxidation resistance during exposure at 800℃, but poorer resistance against oxidation at 900℃. By contrast Ti-48Al-12Cr coating demonstrated excellent isothermal oxidation resistance at both temperatures. Cyclic oxidation tests performed at 800℃ indicated that resistance and no spallation of coatings was observed. But both coatings demonstrated good cyclic oxidation at 900℃ only Ti-48Al-12Cr coating demonstrated excellent cyclic oxidation resistance.

High-temperature mechanical properties of aluminium alloys reinforced with titanium diboride (TiB_2) particles

The physical and mechanical properties of metal matrix composites were improved by the addition of reinforcements. The mechanical properties of particulate-reinforced metal-matrix composites based on aluminium alloys （6061 and 7015） at high temperatures were studied. Titanium diboride （TiB2） particles were used as the reinforcement. All the composites were produced by hot extrusion. The tensile properties and fracture characteristics of these materials were investigated at room temperature and at high temperatures to determine their ultimate strength and strain to failure. The fracture surface was analysed by scanning electron microscopy. TiB2 particles provide high stability of the alumin- ium alloys （6061 and 7015） in the fabrication process. An improvement in the mechanical behaviour was achieved by adding TiB2 particles as reinforcement in both the aluminium alloys. Adding TiB2 particles reduces the ductility of the aluminium alloys but does not change the microscopic mode of failure, and the fracture surface exhibits a ductile appearance with dimples formed by coalescence.

Three-liquid-phase extraction and separation of V(V) and Cr(VI) from acidic leach solutions of high-chromium vanadium–titanium magnetite

A new method by liquid–liquid–liquid three phase system, consisting of acidified primary amine N1923(abbreviated as A-N1923), poly(ethylene glycol)(PEG) and (NH_4)_2SO_4 aqueous solution, was suggested for the separation and simultaneous extraction of V(V) and Cr(VI) from the acidic leach solutions of highchromium vanadium–titanium magnetite. Experimental results indicated that V(V) and Cr(VI) could be selectively enriched into the A-N1923 organic top phase and PEG-rich middle phase, respectively, while Al(III)and other co-existing impurity ions, such as Si(IV), Fe(III), Ti(IV), Mg(II) and Ca(II) in acidic leach solutions,could be enriched in the(NH_4)_2SO_4 bottom aqueous phase. During the process for extraction and separation of V(V) and Cr(VI), almost all of impurity ions could be removed. The separation factors between V(V) and Cr(VI) could reach 630 and 908, respectively in the organic top phase and PEG middle phase, and yields of recovered V(V) and Cr(VI) in the top phase and middle phase respectively were all above 90%.Various effects including aqueous p H, A-N1923 concentration, PEG added amount and(NH_4)_2SO_4 concentration on three-phase partitioning of V(V) and Cr(VI) were discussed. It was found that the partition of Cr(VI) into the PEG-rich middle phase was driven by hydrophobic interaction, while extraction of V(V) by A-N1923 resulted of anion exchange between NO_3^- and H_2V_(10)O_(28)^(-4). Stripping of V(V) and Cr(VI) from the top organic phase and the middle PEG-rich phase were achieved by mixing respectively with NaNO_3 aqueous solutions and Na OH-((NH_4)_2SO_4 solutions. The present work highlights a new approach for the extraction and purification of V and Cr from the complex multi-metal co-existing acidic leach solutions of high-chromium vanadium–titanium magnetite.

Effect of diboron trioxide on the crushing strength and smelting mechanism of high-chromium vanadium–titanium magnetite pellets

The effect of diboron trioxide(B_2O_3) on the crushing strength and smelting mechanism of high-chromium vanadium–titanium magnetite pellets was investigated in this work. The main characterization methods were X-ray fluorescence, inductively coupled plasma–atomic emission spectroscopy, mercury injection porosimetry, X-ray diffraction, metallographic microscopy, and scanning electron microscopy–energy-dispersive X-ray spectroscopy. The results showed that the crushing strength increased greatly with increasing B_2O_3 content and that the increase in crushing strength was strongly correlated with a decrease in porosity, the formation of liquid phases, and the growth and recrystallization consolidation of hematite crystalline grains. The smelting properties were measured under simulated blast furnace conditions; the results showed that the smelting properties within a certain B_2O_3 content range were improved and optimized except in the softening stage. The valuable element B was easily transformed to the slag, and this phenomenon became increasingly evident with increasing B_2O_3 content. The formation of Ti(C,N) was mostly avoided, and the slag and melted iron were separated well during smelting with the addition of B_2O_3. The size increase of the melted iron was consistent with the gradual optimization of the dripping characteristics with increasing B_2O_3 content.

Effect of yttrium on microstructure and mold filling capacity of a near-α high temperature titanium alloy

The addition of rare earth yttrium(Y) can improve the performances of high temperature titanium alloys,such as the tensile ductility,thermal stability and creep property,etc.However,few studies on the effect of Y on the castability of titanium alloys have been carried out,which is significant to fabrication of thin-walled complex titanium castings by investment casting.In this study,the microstructure and mold filling capacity of a Ti-1100 alloy with different Y additions(0,0.1wt.%,0.3wt.%,0.5wt.% and 1.0wt.%) were investigated systematically through investment casting experiments,and the casting experiments were carried out in a centrifugal titanium casting machine.The microstructures of the alloy were observed via the optical microscopy,scanning electron microscopy and transmission electron microscopy.The mold filling capacity was tested by using of a grid pattern and was evaluated by the number of segments completely filled by the cast alloy.The results indicate that the grain size is decreased and the mold filling capacity is improved significantly with increasing the addition of Y from 0 to 1.0wt.%.The average primary grain size of Ti-1100 alloy is reduced from 250 μm to 50 μm and the mold filling capacity is increased from 61.5% to 100%.Considering the potential harmful effect on tensile properties of titanium alloys due to high concentrations of Y,it is suggested that Y addition should be about 0.3wt.%.

HIGH THROUGHPUT DRILLING OF TITANIUM ALLOYS

The experiments of high throughput drilling of Ti-6Al-4V at 183 m/min cutting speed and 156 mm^3/s material removal rate using a 4 mm diameter WC-Co spiral point drill are conducted. At this material removal rate, it took only 0.57 s to drill a hole in a 6.35 mm thick Ti plate. Supplying the cutting fluid via through-the-drill holes and the balance of cutting speed and feed have proven to be critical for drill life. An inverse heat transfer model is developed to predict the heat flux and the drill temperature distribution in drilling. A three-dimensional finite element modeling of drilling is con-ducted to predict the thrust force and torque. Experimental result demonstrates that, using proper machining process parameters, tool geometry, and fine-grained WC-Co tool material, the high throughput machining of Ti alloy is technically feasible.

Delayed Fracture Behavior of CrMo-Type High Strength Steel Containing Titanium

The delayed fracture behaviors of CrMo-type high strength steels containing different amount of titanium(0to 0.10%)were studied.The steels were quenched at 880℃ and tempered from 400℃ to 650℃,and a wide range of tensile strength was obtained.The sustained load tensile test was carried out by using notched tensile specimens in Walpole solution.The experimental results showed that with higher strength,the Ti-microalloyed steels show higher resistance to delayed fracture compared with non-microalloyed steel due to titanium beneficial role and microstructure changes.The undissolved TiC is uniformly distributed as strong hydrogen traps,retarding or preventing the diffusion and accumulation of hydrogen to lower-interaction energy sites,such as prior austenite and martensite lath boundaries in stress concentration area.Meanwhile,the grain refining effect of titanium is also an important factor to improve the delayed fracture resistance of Ti-microalloyed steels.The characteristics of delayed fracture remain nearly the same with titanium addition.

Equilibrium between titanium ions and high-purity titanium electrorefining in a NaCl-KCl melt

TiClx （x=2.17） was prepared by using titanium sponge to reduce the concentration of TiCl4 in a NaCl-KCl melt under negative pressure. The as-prepared NaCl-KCl-TiClx melt was employed as the electrolyte, and two parallel crude titanium plates and one high-purity titanium plate were used as the anode and cathode, respectively. A series of electrochemical tests were performed to investigate the influence of electrolytic parameters on the current efficiency and quality of cathodic products. The results indicated that the quality of cathodic products was related to the current efficiency, which is significantly dependent on the current density and the initial concentration of titanium ions. The significance of this study is the attainment of high-purity titanium with a low oxygen content of 30× 10^-6.

High Temperature Corrosion and Protection of Titanium Alloys and TiAl Intermetallics

High temperature corrsoion and protection of trtanium alloys and TiAl intermetallics are reviewed, andsome suggestions on the development of protective coatings are put forward.

High Scalp Tension after Three-Dimensional Titanium Mesh Repair for Skull Defect: 2 Case Reports

Rationale: The three-dimensional (3D) computer-made titanium mesh is widely used in the skull repair for those patients receiving decompression of the bone flap. It can restore normal anatomy to a greater extent and make a better appearance. Case Presentation: We reported two cases of patients admitted to our hospital who have experienced high scalp tension after skull repair. At first, these two patients underwent decompression of the bone flap, and the physical examination results showed a defect of skull. No neurological symptoms and signs were found. The 3D computed tomography (CT) reconstruction of skull was performed, and then the skull repair with 3D titanium mesh was conducted. But because of high scalp tension, they underwent a second operation, during which we re-trimmed and reduce the arc of the titanium mesh. The scalp incision of both patients healed well and no titanium mesh was exposed. Both patients have a good prognosis. Lessons: We highlight that the high tension of scalp due to overstretching after 3D titanium mesh repair for skull defect should be paid much attention to. Trimming and reducing the arc of titanium mesh is an effective treatment for this situation.

AN INVESTIGATION OF HIGH-TEMPERATURE DEFORMATION STRENGTHENING AND TOUGHENING MECHANISM OF TITANIUM ALLOY

The high-temperature deformation strengthening and toughening mechanisms of titanium alloys have been investigated in this paper. The materials processed by this method produce a new tri-modal microstrvcture, which consists of 10-20% equiaxed alpha, streaky alpha and transformed beta matrix. It is found that the higher ductility of tri-modal microstructure is attributed to the equiaxed alpha's coopemtive slip and coordinated deformation with the transformed beta matrix. The streaky alpha phases not only increase the strength and creep properties, but also increase the fracture toughness. Propagating along grain boundaries between two neighboring streaky alpha phases, cracks in tri-modal microstructure make a more tortuous way, and then the materials show a higher fracture toughness. This new method is applicable to α, near α,α+β and near β titanium alloys.

Tool Failure Analysis in High Speed Milling of Titanium Alloys

In high speed milling of titanium alloys the high rate of tool failure is the main reason for its high manufacturing cost. In this study,fractured tools which were used in a titanium alloys 5-axis milling process have been observed both in the macro scale using a PG-1000 light microscope and in the micro scale using a Scanning Electron Microscope (SEM) respectively. These observations indicate that most of these tool fractures are the result of tool chipping. Further analysis of each chipping event has shown that beachmarks emanate from points on the cutting edge. This visual evidence indicates that the cutting edge is failing in fatigue due to cyclical mechanical and/or thermal stresses. Initial analyses explaining some of the outlying conditions for this phenomenon are discussed. Future analysis regarding determining the underlying causes of the fatigue phenomenon is then outlined.

High Frequency Discharge Plasma Induced Grafting of Polystyrene onto Titanium Dioxide Powder

Grafting of polystyrene （PS） onto titanium dioxide powder was investigated. The graft polymerization reaction was induced by high frequency discharge produced N2 plasma treatment of the surfaces of titanium dioxide. IR, XPS and TGA results show that PS was grafted on the titanium dioxide powder. And the crystal structure of the titanium dioxide powder observed by XRD was unchanged after plasma treatment.

高温高应变率下钛合金Ti6Al4V的动态力学行为及本构关系

采用分离式霍普金森压杆实验技术,研究了钛合金Ti6Al4V在温度为25~800℃、应变速率为2 000~7 000 s-1的冲击压缩下的动态力学行为和微观组织演变,分析了其力学响应的温度依赖性和应变率敏感性,构建了可准确表征材料塑性流动行为的修正Johnson-Cook模型。结果表明,Ti6Al4V具有显著的应变硬化、应变率强化、应变率增塑和温度软化效应。随着加载温度和应变率的升高,材料的应变硬化效应减弱。温度敏感性随加载温度的升高而显著降低。应变率敏感性因子与加载温度呈负相关,随真实应变的增大呈下降趋势。高温高应变率下细小等轴α相、拉长型α相和块状α相取代初始等轴α相成为Ti6Al4V微观组织的典型特征。考虑率-温耦合作用和绝热温升影响的修正Johnson-Cook模型能够准确地预测Ti6Al4V的塑性流动应力-应变响应。

Application of High Tension Roll Separator for the Separation of Titanium Bearing Minerals: Process Modeling and Optimization

The High Tension Roll Separator (HTRS) is one of the main electrostatic unit operations employed to separate titanium minerals like ilmenite, rutile and leucoxene which behave as conducting from zircon, sillimanite, garnet and monazite which behave as non-conducting minerals when a high potential difference is applied. Three process inputs, namely roll speed, feed material temperature and roll speed have been optimized. Experiments were conducted based on the Box- Behnken factorial design;the results were analyzed using response surface methodology (RSM). A new term, called Operational Quality Index (OQI) has been defined as a process output, which is maximized by quadratic programming, to obtain the optimum operating conditions. The maximum value of OQI obtained under the constraints of grade >96% and recovery >98% is 195.53, at the following operating conditions—Temperature: 102°C, Feed Rate: 1.75 tph and Roll Speed: 132 rpm. Under these conditions, the grade and recovery obtained are 96.6% and 98.9% respectively.