A typical 321 stainless steel/aluminum composite coating (321/Al coating) was prepared by high velocity arc spraying technique (HVAS) with 321 stainless steel wire as the anode and aluminum wire as the cathode. The tr...A typical 321 stainless steel/aluminum composite coating (321/Al coating) was prepared by high velocity arc spraying technique (HVAS) with 321 stainless steel wire as the anode and aluminum wire as the cathode. The traditional 321 stainless steel coating was also prepared for comparison. Tribological properties of the coatings were evaluated with the ring-block wear tester under different conditions. The structure and worn surface of the coatings were analyzed by scanning electron microscopy(SEM), X-ray diffractometry(XRD) and energy dispersion spectroscopy(EDS). The results show that, except for aluminum phase addition in the 321/Al coating, no other phases are created compared with the 321 coating. However, due to the addition of aluminum, the 321/Al coating forms a type of "ductile/hard phases inter-deposited" structure and performs quite different tribological behavior. Under the dry sliding condition, the anti-wear property of 321/Al coating is about 42% lower than that of 321 coating. But under the oil lubricated conditions with or without 32 h oil-dipping pretreatment, the anti-wear property of 321/Al coating is about 9% and 5% higher than that of 321 coating, respectively. The anti-wear mechanism of the composite coating is mainly relevant to the decrease of oxide impurities and the strengthening action resulted from the "ductile/hard phases inter-deposited" coating structure.展开更多
Fe-Al based intermetallic composite coatings were in-situ synthesized using Fe-Al/Cr3C2 or Fe-Al/WC cored wires and high velocity are spraying (HVAS) technology. The tribological properties of the Fe-Al based intermet...Fe-Al based intermetallic composite coatings were in-situ synthesized using Fe-Al/Cr3C2 or Fe-Al/WC cored wires and high velocity are spraying (HVAS) technology. The tribological properties of the Fe-Al based intermetallic composite coatings were investigated using a ball-on-disc tribotester from room temperature to 650 ℃. The results show that the coatings have relatively high bond strength and micro-hardness. The tribological properties of Fe-Al/Cr3C2 and Fe-Al/WC composite coatings were further analyzed and compared. Low and stable wear rates of the Fe-Al based intermetallic composite coatings were indicated from room temperature to 650 ℃. The excellent wear resistance of the composite coatings in high temperature was discussed.展开更多
Three types of FeMnCrAl/Cr3C2 coatings with different Al content were deposited on 20# steel substrates by the high velocity arc spraying (HVAS) process. Surface microstructures of the coatings were analyzed by optica...Three types of FeMnCrAl/Cr3C2 coatings with different Al content were deposited on 20# steel substrates by the high velocity arc spraying (HVAS) process. Surface microstructures of the coatings were analyzed by optical microscopy (OM) and X-ray diffractometry (XRD). High temperature erosion (HTE) tests were performed in an erosion tester at different impact angles. The surface morphologies of the eroded coatings were observed on a field emission scanning electron microscope(FE-SEM). The laminated structure is found on all the prepared coatings with the porosity and oxide fraction in the coatings decreasing with the Al content from 0 to 15% (mass fraction). Sample FA3 with 15% Al, possessing the lowest porosity and oxide fraction, has the best HTE resistance, which demonstrates that Al addition can improve the HTE resistance of the coatings. The erosion rate of sample FA1 exhibits a maximum value at 90° impact angle. The maximum erosion rates of both FA2 and FA3 samples appear in the range of 60°-90° impact angles. Erosion loss of the coatings occurs through brittle breaking, cutting and fatigue spalling.展开更多
The effect of Al- and AlSiRE-coatings obtained by arc spray (AS) and high velocity arc spray (HVAS) technologies, on the tensile properties of type 316 steel specimens strained at elevated temperatures in air and vacu...The effect of Al- and AlSiRE-coatings obtained by arc spray (AS) and high velocity arc spray (HVAS) technologies, on the tensile properties of type 316 steel specimens strained at elevated temperatures in air and vacuum has been systematically investigated. It is found that both temperature and environment play an important role in determining the mechanical properties of the coated 316 steel specimens strained at elevated temperatures. And the quantitative changes of surface roughness of coatings before and after straining correspond to the mechanical properties of the 316 steel substrate.展开更多
High-temperature corrosion is a serious problem for the water-wall tubes of boilers used in thermal power plants. Oxidation, sulfidation and molten salt corrosion are main corrosion ways.Thereinto, the most severe cor...High-temperature corrosion is a serious problem for the water-wall tubes of boilers used in thermal power plants. Oxidation, sulfidation and molten salt corrosion are main corrosion ways.Thereinto, the most severe corrosion occurs in molten salt corrosion environment. Materials rich in oxides formers, such as chromium and aluminum, are needed to resist corrosion in high-temperature and corrosive environment, but processability of such bulk alloys is very limited. High velocity electric arc spraying (HVAS) technology is adopted to produce coatings with high corrosion resistance. By comparison, NiCr (Ni-45Cr-4Ti) is recommended as a promising alloy coating for the water-wall tubes, which can even resist molten salt corrosion attack. In the study of corrosion mechanism, the modern material analysis methods, such as scanning electron microscopy (SEM), X-ray diffractometry (XRD) and energy dispersive spectrometry (EDS), are used. It is found that the corrosion resistances of NiCr and FeCrAI coatings are much better than that of 20g steel, that the NiCr coatings have the best anti-corrosion properties, and that the NiCr coatings have slightly lower pores than FeCrAI coatings.It is testified that corrosion resistance of coatings is mainly determined by chromium content, and the microstructure of a coating is as important as the chemical composition of the material. In addition, the fracture mechanisms of coatings in the cycle of heating and cooling are put forward. The difference of the thermal physical properties between coatings and base metals results in the thermal stress inside the coatings. Consequently, the coatings spall from the base metal.展开更多
基金Project(50735006) supported by the National Natural Science Foundation of ChinaProject(2006BAF02A19) supported by the National Science and Technology Support Program of China
文摘A typical 321 stainless steel/aluminum composite coating (321/Al coating) was prepared by high velocity arc spraying technique (HVAS) with 321 stainless steel wire as the anode and aluminum wire as the cathode. The traditional 321 stainless steel coating was also prepared for comparison. Tribological properties of the coatings were evaluated with the ring-block wear tester under different conditions. The structure and worn surface of the coatings were analyzed by scanning electron microscopy(SEM), X-ray diffractometry(XRD) and energy dispersion spectroscopy(EDS). The results show that, except for aluminum phase addition in the 321/Al coating, no other phases are created compared with the 321 coating. However, due to the addition of aluminum, the 321/Al coating forms a type of "ductile/hard phases inter-deposited" structure and performs quite different tribological behavior. Under the dry sliding condition, the anti-wear property of 321/Al coating is about 42% lower than that of 321 coating. But under the oil lubricated conditions with or without 32 h oil-dipping pretreatment, the anti-wear property of 321/Al coating is about 9% and 5% higher than that of 321 coating, respectively. The anti-wear mechanism of the composite coating is mainly relevant to the decrease of oxide impurities and the strengthening action resulted from the "ductile/hard phases inter-deposited" coating structure.
基金Project(50005024) supported by the National Natural Science Foundation of China Project(51489020304JS9101) supported by Foundation of the State Key Laboratory for Remanufacturing, China
文摘Fe-Al based intermetallic composite coatings were in-situ synthesized using Fe-Al/Cr3C2 or Fe-Al/WC cored wires and high velocity are spraying (HVAS) technology. The tribological properties of the Fe-Al based intermetallic composite coatings were investigated using a ball-on-disc tribotester from room temperature to 650 ℃. The results show that the coatings have relatively high bond strength and micro-hardness. The tribological properties of Fe-Al/Cr3C2 and Fe-Al/WC composite coatings were further analyzed and compared. Low and stable wear rates of the Fe-Al based intermetallic composite coatings were indicated from room temperature to 650 ℃. The excellent wear resistance of the composite coatings in high temperature was discussed.
基金Project(2009C31129) supported by the Science and Technology Department of Zhejiang Province, China
文摘Three types of FeMnCrAl/Cr3C2 coatings with different Al content were deposited on 20# steel substrates by the high velocity arc spraying (HVAS) process. Surface microstructures of the coatings were analyzed by optical microscopy (OM) and X-ray diffractometry (XRD). High temperature erosion (HTE) tests were performed in an erosion tester at different impact angles. The surface morphologies of the eroded coatings were observed on a field emission scanning electron microscope(FE-SEM). The laminated structure is found on all the prepared coatings with the porosity and oxide fraction in the coatings decreasing with the Al content from 0 to 15% (mass fraction). Sample FA3 with 15% Al, possessing the lowest porosity and oxide fraction, has the best HTE resistance, which demonstrates that Al addition can improve the HTE resistance of the coatings. The erosion rate of sample FA1 exhibits a maximum value at 90° impact angle. The maximum erosion rates of both FA2 and FA3 samples appear in the range of 60°-90° impact angles. Erosion loss of the coatings occurs through brittle breaking, cutting and fatigue spalling.
文摘The effect of Al- and AlSiRE-coatings obtained by arc spray (AS) and high velocity arc spray (HVAS) technologies, on the tensile properties of type 316 steel specimens strained at elevated temperatures in air and vacuum has been systematically investigated. It is found that both temperature and environment play an important role in determining the mechanical properties of the coated 316 steel specimens strained at elevated temperatures. And the quantitative changes of surface roughness of coatings before and after straining correspond to the mechanical properties of the 316 steel substrate.
文摘High-temperature corrosion is a serious problem for the water-wall tubes of boilers used in thermal power plants. Oxidation, sulfidation and molten salt corrosion are main corrosion ways.Thereinto, the most severe corrosion occurs in molten salt corrosion environment. Materials rich in oxides formers, such as chromium and aluminum, are needed to resist corrosion in high-temperature and corrosive environment, but processability of such bulk alloys is very limited. High velocity electric arc spraying (HVAS) technology is adopted to produce coatings with high corrosion resistance. By comparison, NiCr (Ni-45Cr-4Ti) is recommended as a promising alloy coating for the water-wall tubes, which can even resist molten salt corrosion attack. In the study of corrosion mechanism, the modern material analysis methods, such as scanning electron microscopy (SEM), X-ray diffractometry (XRD) and energy dispersive spectrometry (EDS), are used. It is found that the corrosion resistances of NiCr and FeCrAI coatings are much better than that of 20g steel, that the NiCr coatings have the best anti-corrosion properties, and that the NiCr coatings have slightly lower pores than FeCrAI coatings.It is testified that corrosion resistance of coatings is mainly determined by chromium content, and the microstructure of a coating is as important as the chemical composition of the material. In addition, the fracture mechanisms of coatings in the cycle of heating and cooling are put forward. The difference of the thermal physical properties between coatings and base metals results in the thermal stress inside the coatings. Consequently, the coatings spall from the base metal.
