High wall-plug efficiency 808-nm laser diodes with a power up to 30.1 W

A very highly efficient InGaAlAs/AlGaAs quantum-well structure was designed for 808 nm emission,and laser diode chips 390-μm-wide aperture and 2-mm-long cavity length were fabricated.Special pretreatment and passivation for the chip facets were performed to achieve improved reliability performance.The laser chips were p-side-down mounted on the AlN submount,and then tested at continuous wave(CW)operation with the heat-sink temperature setting to 25℃using a thermoelectric cooler(TEC).As high as 60.5%of the wall-plug efficiency(WPE)was achieved at the injection current of 11 A.The maximum output power of 30.1 W was obtained at 29.5 A when the TEC temperature was set to 12°C.Accelerated life-time test showed that the laser diodes had lifetimes of over 62111 h operating at rated power of 10 W.

Resounding Music Within the High Walls

The No. 4 Prison in Yunnan Province is resounded with beautiful music every day, striking the note of the care about the cultural life among the inmates inside the high walls. The prison organized the orchestra in October 1999. Despite the tight pocket of the prison, it spent nearly 20,000 yuan buying electronic organs, guitars, drums, violins, saxophones and trumpets and later to the orchestra were added such Chinese musical instruments as Sheng, Gu Zheng, Piba and clarinet. Now the orchestra boasts 53 pieces of musical instruments in 22 categories. The members of the orchestra have increased from the original 23 to 29. The name of the orchestra "Concern" signifies that the prison needs the understanding and support from the society and prison inmate needs social care and assistance in their correction. At the beginning, few of the members knew anything about music. The prison

Inside High Walls——Prisons in Shanghai and Suzhou

The article is based on a visit to the Tilanqiao, Qingpu and Women's prisons and a juvenile delinquent rehabilitation center in Shanghai and the Suzhou Prison of Jiangsu Province in February 2001 by the author, a graduate student of human rights. She made the trip with a group of experts from China Society for Human Rights Studies.

Spring Festival Celebrations inside the High Walls——How the prison inmates celebrate Spring Festival in Henan

All the prisons in Henan put on a festive atmosphere as the .Spring Festival approached.The red lanterns, colorful ＂door couplets, beautiful China knots, New Year＇s paintings and the big red giant character ＂福＂, meaning happiness were seen everywhere.

Nonlinear Stability Analysis of Long Span Continuous Rigid Frame Bridge with Thin Wall High Piers

By utilizing the current finite element program ANSYS, two types of finite element models (FEM), the beam model (BM) and shell model (SM), are established for the nonlinear stability analysis of a practical rigid frame bridge—Longtanhe Great Bridge. In these analyses, geometrical and material nonlinearities are simultaneously taken into account. For geometrical nonlinearity, updated Lagrangian formulations are adopted to derive the tangent stiffness matrix. In order to simulate the nonlinear behavior of the plastic hinge of the piers, the multi lines spring element COMBIN39 is used in the SM while the bilinear rotational spring element COMBIN40 is employed in the BM. Numerical calculations show that satisfying results can be obtained in the stability analysis of the bridge when the double coupling nonlinearity effects are considered. In addition, the conclusion is significant for practical engineering.

Wall Sticking of High Water-Cut, Highly Viscous and High Gel-Point Crude Oil Transported at Low Temperatures

Some crude oils with high water cut have the capability to flow below the oil gel point, while the oil particles adhere to the pipe wall in the form of paste, also called "wall sticking". Wall sticking is a serious problem during the pipeline transportation, leading to partial or total blockage of the pipeline and energy wastage. In this paper, a series of laboratory flow loop experiments were conducted to observe the wall sticking characteristics of crude oil with high water cut, high viscosity and high gel point at low transportation temperatures. The effects of shear stress and water cut on the wall sticking rate and occurrence temperature were investigated. Experimental results indicated that the wall sticking rate and occurrence temperature were lower under stronger shear stress and higher water cut conditions. A criterion of wall sticking occurrence temperature(WSOT) and a regression model of wall sticking rate were then established. Finally, the software was developed to calculate the pressure drop along the pipelines of crude oils with high water-cut. It was able to predict the wall sticking thickness of gelled oil and then calculate the pressure drop along the pipelines. A typical case study indicated that the prediction results obtained from the software were in agreement with actual measured values.

Development of a helicon-wave excited plasma facility with high magnetic field for plasma-wall interactions studies

The high magnetic field helicon experiment system is a helicon wave plasma（HWP）source device in a high axial magnetic field（B0）developed for plasma–wall interactions studies for fusion reactors.This HWP was realized at low pressure（5×10^-3-10 Pa）and a RF（radio frequency,13.56 MHz）power（maximum power of 2 k W）using an internal right helical antenna（5 cm in diameter by 18 cm long）with a maximum B0of 6300 G.Ar HWP with electron density～10^18–10^20m^-3 and electron temperature～4–7 e V was produced at high B0 of 5100 G,with an RF power of 1500 W.Maximum Ar^＋ion flux of 7.8×10^23m^-2s^-1 with a bright blue core plasma was obtained at a high B0 of 2700 G and an RF power of 1500 W without bias.Plasma energy and mass spectrometer studies indicate that Ar^＋ ion-beams of 40.1 eV are formed,which are supersonic（～3.1cs）.The effect of Ar HWP discharge cleaning on the wall conditioning are investigated by using the mass spectrometry.And the consequent plasma parameters will result in favorable wall conditioning with a removal rate of 1.1×10^24N2/m^2 h.

Microstructures and Properties of 550 MPa Grade High Strength Thin-walled H-beam Steel

The microstructures and mechanical properties of 550 MPa grade lightweight high strength thin-walled H-beam steel were experimentally studied. The experimental results show that the microstructure of the air-cooled H-beam steel sample is consisted of ferrite, pearlite and a small amount of granular bainites as well as fine and dispersive V（C,N） precipitates. The microstructure of the water-cooled steel sample is consisted of ferrite and bainite as well as a small amount of fine pearlites. The microstructure of the water-cooled sample is finer than that of the air-cooled sample with the average intercept size of the surface grains reaching to 3.5 gna. The finish rolling temperature of the thin-walled high strength H-beam steel is in the range of 750 ~C-850 ~C. The lower the finish rolling temperature and the faster the cooling rate, the finer the ferrite grains, the volume fraction of bainite is increased through water cooling process. Grain refinement strengthening and precipitation strengthening are used as major strengthening means to develop 550 MPa grade lightweight high strength thin- walled H-beam steel. Vanadium partially soluted in the matrix and contributes to the solution strengthening. The 550 MPa grade high-strength thin-walled H-beam steel could be developed by direct air cooling after hot rolling to fully meet the requirements of the target properties.

Effect of wall-cooling on Mack-mode instability in high speed flat-plate boundary layers

The instability of the Mack mode is destabilized by wall-cooling in a high speed boundary layer. The aim of this paper is to study the mechanism of the wall cooling effect on the Mack mode instability by numerical methods. It is shown that the wall-cooling can destabilize the Mack mode instability, similar to the previous conclusions with the exception that the Mack mode instability can be stabilized by wall-cooling if the wall temperature is extremely low. The reversed wall temperature is related to a freestream condition. If the Mach number increases to a large enough value, e.g., about 7, the reversed wall temperature will tend to be zero. It seems that the Mack mode instability is determined by the region between the boundary layer edge and the critical layer. When the wall temperature decreases, this region becomes wider, and the boundary layer becomes more unstable. Additionally, a relative supersonic unstable mode can be observed when the velocity of the critical layer is less than 1 - liMa or is cancelled by the wall-cooling effect. These results provide a deeper understanding on the wall-cooling effect in high speed boundary layers.

Analysis on thermophoretic deposit of fine particle on water wall of 10 MW high temperature gas-cooled reactor

The water wall is an important part of the passive natural circulation residual heat removal system in a high temperature gas-cooled reactor. The maximum temperatures of the pressure shell and the water wall are calcu- lated using annular vertical closed cavity model. Fine particles can deposit on the water wall due to the thermophore- sis effect. This deposit can affect heat transfer. The thermophoretic deposit efficiency is calculated by using Batch and Shen’s formula fitted for both laminar flow and turbulent flow. The calculated results indicate that natural convection is turbulent in the closed cavity. The transient thermophoretic deposit efficiency rises with the increase of the pressure shell’s temperature. Its maximum value is 14%.

Generation of high-energy dual-wavelength domain wall pulse with low repetition rate in an HNLF-based fiber ring laser

The generation of high-energy dual-wavelength domain wall pulse with a low repetition rate is demonstrated in a highly nonlinear fiber （HNLF）-based fiber ring laser. By introducing the intracavity birefringence-induced spectral filtering effect, the dual-wavelength lasing operation can be achieved. In order to enhance the cross coupling effect between the two lasing beams for domain wall pulse formation, a 215-m HNLF is incorporated into the laser cavity. Experimentally, it is found that the dual-wavelength domain wall pulse with a repetition rate of 77.67 kHz could be efficiently obtained through simply rotating the polarization controller （PC）. At a maximum pump power of 322 mW, the 655-nJ single pulse energy in cavity is obtained. The proposed configuration provides a simpler and more efficient way to generate high energy pulse with a low repetition rate.

适应锅炉调峰运行的水冷壁高温腐蚀预测模型

随着可再生能源大规模并网,传统火电机组作为调配能源的地位显著增强,这对锅炉灵活调峰运行的安全稳定性提出了更高要求。本文耦合烟气侧与工质侧传热,结合管壁温计算,形成水冷壁壁温分布耦合计算方法。同时,建立了用于确定还原性气氛下的燃料硫释放以及含硫组分的相互转化过程的SO_(x)生成模型。综合炉膛数值模拟、水冷壁壁温耦合计算以及包含时间维度的管壁高温腐蚀模型,提出了一种适应锅炉调峰运行的水冷壁高温腐蚀预测模型并基于Matlab GUI开发了对应软件。选取一台超临界600MW四角切圆燃煤锅炉为研究对象,结果表明:采用壁温耦合计算模型和SO_(x)生成模型得到水冷壁的壁温分布和近壁面H_(2)S浓度分布准确度高,为水冷壁高温腐蚀的准确预测提供了良好基础。不同负荷下水冷壁高温腐蚀特征存在差异,壁面腐蚀程度整体上随负荷降低而降低。100%BMCR与75%THA负荷下前墙水冷壁燃烧器与SOFA之间的区域腐蚀最为严重,最大年腐蚀深度分别为276μm和233μm;50%THA与35%BMCR负荷下高温腐蚀深度在燃烧器区域的上部迅速增加至最大值,分别为224μm和256μm。多工况运行水冷壁高温腐蚀状态表现为各工况腐蚀状态的时空叠加。运用水冷壁高温腐蚀预测模型可实现通过锅炉运行参数和运行时间预测多工况下水冷壁高温腐蚀状态程度的时空分布。

High-speed countercurrent chromatography for purification of single-walled carbon nanotubes

A new chromatographic purification of single-walled carbon nanotubes using high-speed countercurrent chromatography is reported. The purification was accomplished on the basis of experiment that dispersed the single-walled carbon nanotubes with sodium dodecyl sulfate, and the result mixture was separated using the two phase system composed of n-butanol/water = 1/1 （v/v）. The sizes of SWNTs separated were observed by scanning electron microscopy. The results demonstrated that the high-speed countercurrent chromatography possessed a good efficency for purification of single-walled carbon nanotubes.

复杂条件下高面板堆石坝的特殊结构体安全监测设计体系研究

为了加强高面板堆石坝工程中挤压边墙、高趾墩和高趾墙等特殊结构体的安全监测,基于面板堆石坝安全监测设计资料,总结了特殊结构体在安全监测设计方面存在的不足和缺陷。通过收集整理国内包含高趾墩、高趾墙和挤压边墙等特殊结构体的高面板堆石坝数值分析成果,发掘特殊结构体的变形和应力应变规律,将特殊结构体的变形、应力应变及温度、接缝和渗流明确为安全监测设计重点;结合已有面板堆石坝工程的安全监测设计资料,构建了复杂条件下高面板堆石坝特殊结构体安全监测设计体系。该体系能够为在建和拟建的面板堆石坝特殊结构体安全监测设计提供科学的指导,全面提升面板堆石坝的安全监测水平。

THE ANALYSIS OF RESCURED HIGH TENSION PNEUMOTHORAX AND LARGE AREA CHEST WALL DEFECTS

After analyzing 15 clinical case, 2 of which is especially representative, about perforating injury at the areaintegrates thoracic and abdominal cavities in our hospital from Jan. 1988 to Aug. 2001, the writers have summarized some therapyon it. First, to avoid delaying surgery operation , those who are injured at that area seriously should be treated with surgeryoperations immediately without X ray and supersonic checks. Second, the positive check results of suspect patients should behelpful for diagnosis, however the negative ones also could not be excluded of the diagnosis clues. The writers think that theconcomitant observation results with the development of illness are most significant. Third, the emphasis of treatments for thoseinjuries should be paid on abdomen. Explore the abdomen is necessary for the situations that abdominal substantial organs bleedand vacuum organs break, thoracic close drainage is sufficient for treating most thoracic trauma cases. It has been improved to beconvenient to check the thoracic cavities by cutting off the diaphragma temporarily if necessary. Fourth, as it was reported that asmany as 97 per cent of patients will have visceral injury dues to abdominal gunshot wound, all gunshot wounds be done with anexploratory laparotomy without hesitation. Fifth, resuscitating of patients as soon as possible is the key to decrease the mortalityand complications. Sixth, acute pancreas injury should be treated as acute pancreatitis.

锅炉水冷壁管失效分析

锅炉水冷壁管材料为20G钢,在320℃和10.3 MPa下使用约5年后外表面出现鼓包并泄漏。对失效的水冷壁管进行了宏观检查、化学成分分析、力学性能检测、金相检验、腐蚀产物分析及锅炉水质检测。结果表明:水冷壁管失效是由于锅炉水碱性超标从而发生高温碱腐蚀所致。

高层剪力墙结构多目标智能设计方法

高层剪力墙结构智能设计包括智能建模和智能优化两个环节。目前智能建模环节缺乏梁自动化布置和荷载自动化布置;智能优化环节只考虑材料成本而未考虑施工的便捷性。此外,现有的智能设计方法均局限于单标准层的高层剪力墙结构。为此,该文提出了高层剪力墙结构多目标智能设计方法,包括多标准层高层剪力墙结构的智能建模和多目标优化。多标准层高层剪力墙结构智能建模包含剪力墙智能布置、梁自动化布置、板自动化布置和荷载自动化布置;以材料成本和施工便捷性为目标,采用分步优化策略和基于小生境技术的遗传算法对高层剪力墙结构进行多目标优化。通过实际工程算例对所提出的方法进行了验证,结果表明,所提出的高层剪力墙结构多目标智能设计方法稳定、可靠,可以较好地兼顾材料成本和施工的便捷性,并能显著缩短设计周期。

大风区高速铁路路基双侧挡风墙周围沙粒沉积数值模拟研究

兰新高速铁路横穿多个大风区,对其安全运营造成严重影响。为降低强风对线路的危害,在大风区修筑大量防风构筑物,其中以路基挡风墙最为常见,挡风墙降低了风害的影响,但是带来严重的线路积沙问题。通过数值模拟研究不同风速下路基双侧挡风墙周围的流场特征,利用风产生的壁面剪切应力与沙粒剪切应力的比值确定地表沙粒沉积与侵蚀类型。研究发现,气流在两道挡风墙之间分别形成一个顺时针涡流和一个逆时针涡流,在第二道挡风墙背风侧形成一个顺时针大涡,随着来流风速增大,漩涡尺寸和涡流强度均在增大;由于涡流的存在,部分沙粒被卷走,路堤背风坡附近以及路基面上的沙粒沉积显著减少,当来流风速为24、30 m/s时,南北侧线路道床面均出现沙粒反向侵蚀;单双侧挡风墙的积沙规律对比结果表明,设置双侧挡风墙时,线路积沙显著减少。研究揭示了大风区铁路双侧挡风墙周围路基面上的沙粒沉积规律,对未来风区铁路的防护建设具有指导意义。

7T超高场磁共振颅内血管壁成像在缺血性脑卒中病因分型中的研究进展

缺血性脑卒中的病因分型对临床治疗决策和预后判断有重要价值。近年来,随着高分辨率磁共振血管壁成像(high-resolution vessel wall magnetic resonance imaging,HR-VW-MRI)在脑卒中临床研究和实践中的应用增加,7 T MRI以其更高信噪比和更优图像质量,可发现脑血管早期、细微的病理变化,为深入了解各种脑血管疾病的病理机制提供了新思路。然而,超高场强也存在B1场不均、扫描时间长等技术挑战。本文就7 T HR-VW-MRI在缺血性卒中病因分型及临床应用中的进展进行综述,深入分析7 T HR-VW-MRI在提升临床诊断精确性与指导临床治疗中的潜在价值,为临床实践与科研探索提供参考。