Ultrafast dynamics in photo-excited Mott insulator Sr_(3)Ir_(2)O_7 at high pressure

High-pressure ultrafast dynamics,as a new crossed research direction,are sensitive to subtle non-equilibrium state changes that might be unresolved by equilibrium states measurements,providing crucial information for studying delicate phase transitions caused by complex interactions in Mott insulators.With time-resolved transient reflectivity measurements,we identified the new phases in the spin–orbit Mott insulator Sr_(3)Ir_(2)O_7 at 300 K that was previously unidentified using conventional approaches such as x-ray diffraction.Significant pressure-dependent variation of the amplitude and lifetime obtained by fitting the reflectivity?R/R reveal the changes of electronic structure caused by lattice distortions,and reflect the critical phenomena of phase transitions.Our findings demonstrate the importance of ultrafast nonequilibrium dynamics under extreme conditions for understanding the phase transition of Mott insulators.

Experimental and numerical study on dynamic mechanical behaviors of shale under true triaxial compression at high strain rate

High-energy gas fracturing of shale is a novel,high efficacy and eco-friendly mining technique,which is a typical dynamic perturbing behavior.To effectively extract shale gas,it is important to understand the dynamic mechanical properties of shale.Dynamic experiments on shale subjected to true triaxial compression at different strain rates are first conducted in this research.The dynamic stress-strain curves,peak strain,peak stress and failure modes of shale are investigated.The results of the study indicate that the intermediate principal stress and the minor principal stress have the significant influence on the dynamic mechanical behaviors,although this effect decreases as the strain rate increases.The characteristics of compression-shear failure primarily occur in shale subjected to triaxial compression at high strain rates,which distinguishes it from the fragmentation characteristics observed in shale under dynamic uniaxial compression.Additionally,a numerical three-dimensional Split Hopkinson Pressure Bar(3D-SHPB),which is established by coupling PFC3D and FLAC3D methods,is validated to replicate the laboratory characteristics of shale.The dynamic mechanical characteristics of shale subjected to different confining stresses are systematically investigated by the coupling PFC3D and FLAC3D method.The numerical results are in good agreement with the experimental data.

An Arbitrarily High Order and Asymptotic Preserving Kinetic Scheme in Compressible Fluid Dynamic

We present a class of arbitrarily high order fully explicit kinetic numerical methods in compressible fluid dynamics,both in time and space,which include the relaxation schemes by Jin and Xin.These methods can use the CFL number larger or equal to unity on regular Cartesian meshes for the multi-dimensional case.These kinetic models depend on a small parameter that can be seen as a"Knudsen"number.The method is asymptotic preserving in this Knudsen number.Also,the computational costs of the method are of the same order of a fully explicit scheme.This work is the extension of Abgrall et al.(2022)[3]to multidimensional systems.We have assessed our method on several problems for two-dimensional scalar problems and Euler equations and the scheme has proven to be robust and to achieve the theoretically predicted high order of accuracy on smooth solutions.

Boosting High-Voltage Dynamics Towards High-Energy-Density Lithium-Ion Capacitors

Lithium-ion capacitors(LICs)are becoming important electrochemical energy storage systems due to their great potential to bridge the gap between supercapacitors and lithium-ion batteries.However,capacity lopsidedness and low output voltage greatly hinder the realization of high-energy-density LICs.Herein,a strategy of balancing capacity towards fastest dynamics is proposed to enable high-voltage LICs.Through electrochemical prelithiation of Nb_(2)C to be 1.1 V with 165 mAh g^(-1),Nb_(2)C//LiFePO_(4) LICs show a broadened potential window from 3.0 to 4.2 V and an according high energy density of 420 Wh kg^(-1).Moreover,the underlying mechanism between prelithiation and high voltage is disclosed by electrochemical dynamic analysis.Prelithiation declines the Nb_(2)C anode potential that facilitates electron transmission in the interlayer of two-dimensional Nb_(2)C MXene.This effect induces small drive force for Li^(+)ions deposition and hence weakens the repulsive force from adsorbed ions on the electrode surface.Benefiting from even more Li^(+)ions deposition,a higher voltage is eventually delivered.In addition,prelithiation significantly increases Coulomb efficiency of the 1st cycle from 74%to 90%,which is crucial to commercial application of LICs.

Human mesenchymal stem cells exhibit altered mitochondrial dynamics and poor survival in high glucose microenvironment

BACKGROUND Mesenchymal stem cells(MSCs)are a type of stem cells that possess relevant regenerative abilities and can be used to treat many chronic diseases.Diabetes mellitus(DM)is a frequently diagnosed chronic disease characterized by hyperglycemia which initiates many multisystem complications in the long-run.DM patients can benefit from MSCs transplantation to curb down the pathological consequences associated with hyperglycemia persistence and restore the function of damaged tissues.MSCs therapeutic outcomes are found to last for short period of time and ultimately these regenerative cells are eradicated and died in DM disease model.AIM To investigate the impact of high glucose or hyperglycemia on the cellular and molecular characteristics of MSCs.METHODS Human adipose tissue-derived MSCs(hAD-MSCs)were seeded in low(5.6 mmol/L of glucose)and high glucose(25 mmol/L of glucose)for 7 d.Cytotoxicity,viability,mitochondrial dynamics,and apoptosis were deplored using specific kits.Western blotting was performed to measure the protein expression of phosphatidylinositol 3-kinase(PI3K),TSC1,and mammalian target of rapamycin(mTOR)in these cells.RESULTS hAD-MSCs cultured in high glucose for 7 d demonstrated marked decrease in their viability,as shown by a significant increase in lactate dehydrogenase(P<0.01)and a significant decrease in Trypan blue(P<0.05)in these cells compared to low glucose control.Mitochondrial membrane potential,indicated by tetramethylrhodamine ethyl ester(TMRE)fluorescence intensity,and nicotinamide adenine dinucleotide(NAD+)/NADH ratio were significantly dropped(P<0.05 for TMRE and P<0.01 for NAD+/NADH)in high glucose exposed hAD-MSCs,indicating disturbed mitochondrial function.PI3K protein expression significantly decreased in high glucose culture MSCs(P<0.05 compared to low glucose)and it was coupled with significant upregulation in TSC1(P<0.05)and downregulation in mTOR protein expression(P<0.05).Mitochondrial complexes I,IV,and V were downregulated profoundly in high glucose(P<0.05 compared to low glucose).Apoptosis was induced as a result of mitochondrial impairment and explained the poor survival of MSCs in high glucose.CONCLUSION High glucose impaired the mitochondrial dynamics and regulatory proteins in hAD-MSCs ensuing their poor survival and high apoptosis rate in hyperglycemic microenvironment.

Decomposition of Mathematical Programming Models for Aircraft Wing Design Facilitating the Use of Dynamic Programming Approach

Aircraft designers strive to achieve optimal weight-reliability tradeoffs while designing an aircraft. Since aircraft wing skins account for more than fifty percent of their structural weight, aircraft wings must be designed with utmost care and attention in terms of material types and thickness configurations. In particular, the selection of thickness at each location of the aircraft wing skin is the most consequential task for aircraft designers. To accomplish this, we present discrete mathematical programming models to obtain optimal thicknesses either to minimize weight or to maximize reliability. We present theoretical results for the decomposition of these discrete mathematical programming models to reduce computer memory requirements and facilitate the use of dynamic programming for design purposes. In particular, a decomposed version of the weight minimization problem is solved for an aircraft wing with thirty locations (or panels) and fourteen thickness choices for each location to yield an optimal minimum weight design.

Study on dynamic response of high speed train window glass under tunnel aerodynamic effects

Purpose-This paper aims to analyze the bearing characteristics of the high speed train window glass under aerodynamic load effects.Design/methodology/approach-In order to obtain the dynamic strain response of passenger compartment window glass during high-speed train crossing the tunnel,taking the passenger compartment window glass of the CRH3 high speed train onWuhan-Guangzhou High Speed Railway as the research object,this study tests the strain dynamic response and maximum principal stress of the high speed train passing through the tunnel entrance and exit,the tunnel and tunnel groups as well as trains meeting in the tunnel at an average speed of 300 km$h-1.Findings-The results show that while crossing the tunnel,the passenger compartment window glass of high speed train is subjected to the alternating action of positive and negative air pressures,which shows the typical mechanic characteristics of the alternating fatigue stress of positive-negative transient strain.The maximum principal stress of passenger compartment window glass for high speed train caused by tunnel aerodynamic effects does not exceed 5 MPa,and the maximum value occurs at the corresponding time of crossing the tunnel groups.The high speed train window glass bears medium and low strain rates under the action of tunnel aerodynamic effects,while the maximum strain rate occurs at the meeting moment when the window glass meets the train head approaching from the opposite side in the tunnel.The shear modulus of laminated glass PVB film that makes up high speed train window glass is sensitive to the temperature and action time.The dynamically equivalent thickness and stiffness of the laminated glass and the dynamic bearing capacity of the window glass decrease with the increase of the action time under tunnel aerodynamic pressure.Thus,the influence of the loading action time and fatigue under tunnel aerodynamic effects on the glass strength should be considered in the design for the bearing performance of high speed train window glass.Originality/value-The research results provide data support for the analysis of mechanical characteristics,damage mechanism,strength design and structural optimization of high speed train glass.

Dynamic Performance of High Speed Solenoid Valve with Parallel Coils

The methods of improving the dynamic performance of high speed on/off solenoid valve include increasing the magnetic force of armature and the slew rate of coil current, decreasing the mass and stroke of moving parts. The increase of magnetic force usually leads to the decrease of current slew rate, which could increase the delay time of the dynamic response of solenoid valve. Using a high voltage to drive coil can solve this contradiction, but a high driving voltage can also lead to more cost and a decrease of safety and reliability. In this paper, a new scheme of parallel coils is investigated, in which the single coil of solenoid is replaced by parallel coils with same ampere turns. Based on the mathematic model of high speed solenoid valve, the theoretical formula for the delay time of solenoid valve is deduced. Both the theoretical analysis and the dynamic simulation show that the effect of dividing a single coil into N parallel sub-coils is close to that of driving the single coil with N times of the original driving voltage as far as the delay time of solenoid valve is concerned. A specific test bench is designed to measure the dynamic performance of high speed on/off solenoid valve. The experimental results also prove that both the delay time and switching time of the solenoid valves can be decreased greatly by adopting the parallel coil scheme. This research presents a simple and practical method to improve the dynamic performance of high speed on/off solenoid valve.

Model test on dynamic characteristics of invert and foundation soils of high-speed railway tunnel

A dynamic model test(CL = 4) at different velocities of train,namely different loading frequencies,is carried out to study the dynamic characteristics of a high-speed railway tunnel invert and its foundation soils.Not only are the accelerations,dynamic coefficients,dynamic stresses of the invert and foundation soils emphatically analyzed,their relationship with the velocity of the train are discussed in detail.Through laboratory testing,the attenuation of vibration propagating from up the rails is obtained and the calculation formula of the speed influence coefficient of the tunnel invert is preliminarily established.The depth of the foundation soils influenced by vibration is also determined in this study.It is shown that the responses of the tunnel invert and foundation soils to vibration are slightly increased with the velocity of the train;circumferential stresses in the bottom of the invert are tensile stresses and maximum stresses appear under the foot of the rails;the dynamic soil pressures of the foundation decrease quickly with the distance away from the tunnel invert and an exponential relationship exists between them.

High density gas state at water/graphite interface studied by molecular dynamics simulation

In this paper molecular dynamics simulations are performed to study the accumulation behaviour of N2 and H2 at water/graphite interface under ambient temperature and pressure. It finds that both N2 and H2 molecules can accumulate at the interface and form one of two states according to the ratio of gas molecules number to square of graphite surface from our simulation results： gas films （pancake-like） for a larger ratio and nanobubbles for a smaller ratio. In addition, we discuss the stabilities of nanobubbles at different environment temperatures. Surprisingly, it is found that the density of both kinds of gas states can be greatly increased, even comparable with that of the liquid N2 and liquid H2. The present results are expected to be helpful for the understanding of the stable existence of gas film （pancake-like） and nanobubbles.

Study on dynamic mechanical properties of high nitrogen steels

Reliable dynamic mechanical properties of high nitrogen steels are necessary for the design and assessment of armor structures subject to impact and blast. A series of experiments, based on Hopkinson bar techniques, were conducted and described in this study. The dynamic compression, tensile and shear properties of high nitrogen steel had been tested, and the stress-strain curves under high strain rates were obtained. The results have been showed as follows: High nitrogen steel has a remarkable strain rate strengthening effect. Compared to the static curves, the constitutive curves of dynamic tension and compression move upper. The dynamic compressive yield strength of high nitrogen steel increases first and then decreases with the increase of strain rate, and the yield strength varies in the range of 1465-1549 MPa within the range of 1147-2042 s^(-1) strain rate; The tensile strength of high nitrogen steel increases with the increase of strain rate. When the strain rate is greater than 1341 s^(-1), the tensile strength will not increase and the curve tends to be gentle. The pure shear yield strength of the high nitrogen steel is above 800 MPa.

A Preliminary Study on Dynamics and Models of N,P,K Absorption for High-Yield Cotton

The field experiments were carried out to investigate the dynamics and models of N, P and K absorption for the cotton plants with a lint of 3 000 kg ha-1 in Xinjiang. The main results were as follows: The contents of N, P2O5, K2O in cotton leaves, stems, squares and bolls decreased obviously with the time over the whole growth duration and the falling extent was greater in high-yield cotton than in CK. Contents of N in leaves, squares and bolls, in particular in the leaves of fruit-bearing shoot was higher in high-yield cotton than in CK. Contents of P2O5 in squares and bolls and that of K2O in stems were higher in high-yield cotton than in CK during the whole growing period. The accumulations of N, P2O5 and K2O in the cotton plants could be described with a logistic curve equation. There was the fastest nutrient uptake at about 90 d for N, 92 d for P2O5 and 85 d for K2O after emergence, respectively. Total nutrient accumulation of N, P2O5 and K2O was 385.8, 244. 7 and 340.3 kg ha-1, respectively. Approximately 12. 5 kg N, 8. 0 kg P2O5 and 11.1 kg K2O were needed for producing 100 kg lint with the leaves and stems under the super high yield condition of 3 000 kg ha-1 in Xinjiang.

Manufacturing Error Effects on Mechanical Properties and Dynamic Characteristics of Rotor Parts under High Acceleration

Stress, strain and vibration characteristics of rotor parts should be changed significantly under high acceleration, manufacturing error is one of the most important reason. However, current research on this prob- lem has not been carried out. A rotor with an acceleration of 150,000 g is considered as the objective, the effects of manufacturing errors on rotor mechanical properties and dynamic characteristics are executed by the selection of the key affecting factors. Through the force balance equation of the rotor infinitesimal unit establishment, a theoretical model of stress calculation based on slice method is pro- posed and established, a formula for the rotor stress at any point derives. A finite element model （FEM） of rotor with holes is established with manufacturing errors. The chan- ges of the stresses and strains of a rotor in parallelism and symmetry errors are analyzed, which verify the validity of the theoretical model. The pre-stressing modal analysis is performed based on the aforementioned static analysis. The key dynamic characteristics are analyzed. The results demonstrated that, as the parallelism and symmetry errors increase, the equivalent stresses and strains of the rotor slowly increase linearly, the highest growth rate does not exceed 4%, the maximum change rate of natural frequency is 0.1%. The rotor vibration mode is not significantlyaffected. The FEM construction method of the rotor with manufacturing errors can be utilized for the quantitative research on rotor characteristics, which will assist in the active control of rotor component reliability under high acceleration.

High mobility group protein 1: A collaborator in nucleosome dynamics and estrogen-responsive gene expression

High mobility group protein 1(HMGB1) is a multifunctional protein that interacts with DNA and chromatin to influence the regulation of transcription, DNA replication and repair and recombination. We show that HMGB1 alters the structure and stability of the canonical nucleosome(N) in a nonenzymatic,adenosine triphosphate-independent manner. As a result, the canonical nucleosome is converted to two stable, physically distinct nucleosome conformers. Although estrogen receptor(ER) does not bind to its consensus estrogen response element within a nucleosome, HMGB1 restructures the nucleosome to facilitate strong ER binding. The isolated HMGB1-restructured nucleosomes(N' and N'') remain stable and exhibit a number of characteristics that are distinctly different from the canonical nucleosome. These findings complement previous studies that showed(1) HMGB1 stimulates in vivo transcriptional activation at estrogen response elements and(2) knock down of HMGB1 expression by siR NA precipitously reduced transcriptional activation. The findings indicate that a major facet of the mechanism of HMGB1 action involves a restructuring of aspects of the nucleosome that appear to relax structural constraints within the nucleosome. The findings are extended to reveal the differences between ER and the other steroid hormone receptors. A working proposal outlines mechanisms that highlight the multiple facets that HMGB1 may utilize in restructuring the nucleosome.

Optimization of the carrier tracking loop for GPS high dynamic receivers

A carrier tracking loop which can adjust the loop parameters adaptively is proposed for high dynamic application. Three modules, called the α-β-γT filter model, adaptive loop structure mod- el and adaptive loop bandwidth model respectively, are added in the presented tracking loop com- pared with the traditional carrier tracking loop based on the second-order frequency lock loop （FLL） assisting third-order phase lock loop （PLL） loop filter. And the optimization methods for the track- ing bandwidth and the carrier loop order are analyzed. The real-time estimation methods of the dy- namic parameters, the velocity, acceleration and jerk along the line of sight （LOS） between the sat- ellite and the receiver＇ s antenna, and the measurement parameters are discussed based on the pres- ented α-β-γ filter algorithm. A method is introduced to improve the filter＇ s dynamic response to meet high dynamic application by self-adjusted α-β-γ filter coefficient used in the tracking loop. The performance of three cases with different carrier tracking loop is compared by simulation.

Influences of Stress Wave Propagation upon Studying Dynamic Response of Materials at High Strain Rates

How the wave propagation analysis plays a key role in the studies of dynamic response of materials at high strain rates is analyzed. For the wave propagation technique, the followings are important: the loading and unloading constitutive relation presumed, the positions of the sensors embedded, the interactions between loading waves and unloading waves. For the split Hopkinson pressure bar (SHPB) technique, the assumption of one-dimensional stress wave propagation and the assumption of stress uniformity along the specimen should be satisfied. When the larger diameter bars are employed, the wave dispersion effects should be considered, including the high frequency oscillations, non-uniform stress distribution across the bar section, increase of rise time, and amplitude attenuation. The stress uniformity along the specimen is influenced by the reflection times in specimen, the wave impedance ratio of the specimen and the bar, and the waveform.

Robust Fault-Tolerant Control for Longitudinal Dynamics of Aircraft with Input Saturation

A robust fault-tolerant control scheme is proposed for the longitudinal dynamics of an aircraft with input saturation,using the anti-windup method and the fault detection observer technology.To estimate the system fault,a detection observer is designed for the longitudinal dynamics,and a fault-tolerant control law is developed to compensate for the fault effects of the longitudinal dynamics.Then,an anti-windup compensator is augmented into the fault-tolerant control law to eliminate the effect of input saturation.Using linear matrix inequality(LMI)technology,the detection observer based fault-tolerant controller is designed to ensure the stability of the closed-loop system and the convergence of the detection observer.Finally,the developed robust fault-tolerant control scheme is applied to the longitudinal model of an aircraft and simulation results are presented to illustrate the effectiveness of the proposed control scheme.

Dynamic compressive property and failure behavior of extruded Mg-Gd-Y alloy under high temperatures and high strain rates

For the purpose of investigating the dynamic deformational behavior and failure mechanisms of magnesium under high strain rates,the Split Hopkinson Pressure Bar(SHPB)was used for investigating dynamic mechanical properties of extruded Mg-Gd-Y Magnesium alloy at ambient temperature(300 K),200℃(473 K)and 300℃(573 K)temperature.The samples after compression were analyzed by scanning electron microscope(SEM)and metallographic microscope.Dynamic mechanical properties,crack performance and plastic deformation mechanism of extruded Mg-Gd-Y Magnesium alloy along the extrusion direction(ED)were discussed.The results show that,extruded Mg-Gd-Y Magnesium alloy has the largest dynamic compressive strength which is 535 MPa at ambient temperature(300 K)and strain rate of 2826 s^(−1).When temperature increases,dynamic compressive strength decreases,while ductility increases.The dynamic compression fracture mechanism of extruded Mg-Gd-Y Magnesium alloy is multi-crack propagation and intergranular quasi-cleavage fracture at both ambient temperature and high temperature.The dynamic compressive deformation mechanism of extruded Mg-Gd-Y Magnesium alloy is a combination of twinning,slipping and dynamic recrystallization at both ambient temperature and high temperature.

THE HIGH RESOLUTION SEISMIC TOMOGRAPHIC IMAGE IN QINGHAI—TIBET PLATEAU AND ITS DYNAMIC IMPLICATIONS

The Qinghai—Tibet plateau and its surrounding areas including Indian subcontinent, Xinjiang, Mongolia, is a largest lithosphere convergence place in the world, which characterized by continent\|continent collision with a thick crust and lithosphere. The high resolution seismic surface wave tomographic inversion has been conducted for studying the 3D velocity structure of crust and upper mantle in those areas. The seismic surface waveform data are from the archives of the CDSN, GSN and GEOSCOPE. About 2400 long period surface waveform recordings are available for both dispersion and waveform tomographic inversion. The block inversion by grid 1°×1°in Qinghai—Tibet plateau and 2°×2°in the surrounding areas were adapted. The resulting maps show the high resolution 3D shear wave velocity variation from earth’s surface to 400km depth.

Rock damage and fracturing induced by high static stress and slightly dynamic disturbance with acoustic emission and digital image correlation techniques

A series of coupled static-dynamic loading tests is carried out in this study to understand the effect of slightly dynamic disturbance on the rocks under high static stress.The acoustic emission(AE)and digital image correlation(DIC)techniques are combined to quantitatively characterize the damage and fracturing behaviors of rocks.The effects of three influencing factors,i.e.initial static stress,disturbance amplitude,and disturbance frequency,on the damage and fracturing evolution are analyzed.The experimental results reveal the great differences in AE characteristics and fracturing behaviors of rocks under static loads and coupled static-dynamic loads.Both the Kaiser effect and Felicity effect are observed during the disturbance loading process.The crack initiation,stable and unstable propagation in the highly-stressed rocks can be triggered by cyclic disturbance loads,and more local tensile splitting cracks are found in the rocks subjected to coupled static-dynamic loads.The damage and fracturing evolution of rocks during cyclic disturbances can be divided into two stages,i.e.steady and accelerated stages,and the increase rate and proportion of each stage are greatly affected by these influencing factors.High initial static stress,low disturbance frequency,and high disturbance amplitude are considered to be adverse factors to the stability of the rocks,which would induce a high increase rate of the steady stage and a high proportion of the accelerated stage within the whole disturbance period.Based on the two-stage damage evolution trend,a linear-exponential damage model is employed to predict the instability of the rocks under coupled static-dynamic loads.