The most prominent feature of the extensional tectonic framework of post high pressure (HP) and ultrahigh pressure (UHP) metamorphism in Dabieshan is the development of the multi layered extension detachment zones ...The most prominent feature of the extensional tectonic framework of post high pressure (HP) and ultrahigh pressure (UHP) metamorphism in Dabieshan is the development of the multi layered extension detachment zones surrounding the core of the Luotian dome, and the separation of the UHP, HP and epidote blueschist units by the detachment zones, which form the vertically stacking sheet like slices of the HP and UHP metamorphic rocks. From the core outwards, exist the HP and UHP rock barren Dabie complex, UHP unit, HP unit and epidote blueschist unit. The extension tectonics of post HP and UHP metamorphic event constrain the distribution and present configuration of the HP and UHP metamorphic rocks, and the extensional tectonic framework bears some similarities to the Cordillera metamorphic core complex. It is suggested that partial melting happened in the Dabie gneiss complex (DGC) and UHP unit contemporaneously with the extrusion of UHP metamorphic rocks into the lower-middle crust. The formation and emplacement of the migmatite and granites are the response to the change in thermal state, facilitating the transfer from the compressive regime to extensional regime in the crust. The large scale crustal extension and uplift and the accompanying anatexis in Dabieshan are probably related to the delamination and magmatic underplating in the mantle and the lower crust.展开更多
In the gneisses from the drillhole ZK2304 of the Donghai area, there have been preserved high- and ultrahigh-pressure metamorphic mineral assemblages, a series of complicated retrogressive textures and relevant metamo...In the gneisses from the drillhole ZK2304 of the Donghai area, there have been preserved high- and ultrahigh-pressure metamorphic mineral assemblages, a series of complicated retrogressive textures and relevant metamorphic reactions. In addition to garnet, jadeititic-clinopyroxene and rutile, other peak stage (M2) minerals in some gneisses include phengite, aragonite and coesite or quartz pseudomorphs after coesite. The typical peak-stage mineral assemblages in gneisses are characterized by garnet + jadeitic-clinopyroxene + rutile + coesite, garnet + jadeitic-clinopyroxene + phengite + rutile ± coesite and garnet + jadeitic-clinopyroxene + aragonite + rutile ± coesite. The grossular content (Gro) in garnet is high and may reach 50. 1 mol%. The SiO2 content of phengite ranges from 54.37% to 54.84% with 3.54-3.57 p.f.u. Quartz pseudomorphs after coesite occur as inclusions in garnet.The gneisses of the Donghai area have been subjected to multistage recrystallization and exhibit a closewise P-T evolutional path characterized by the near-isothermal decompression. The inclusion assemblage (Hb+Ep+Bi+Pl+Qz) within garnet and other minerals has recorded a pre-peak stage (Mi) epidote amphibole fades metamorphic event. High- and ultrahigh-pressure peak metamorphism (M2) took place at T=750-860℃ and P>2.7 GPa. The symplectitic assemblages after garnet, jadeitic-clinopyroxene and rutile imply a near-isothermal decompression metamorphism (M3, M4) during the rapid exhumation. Several lines of evidence of petrography and metamorphic reactions indicate that both gneisses and eclogites have experienced ultrahigh-pressure metamorphism in the Donghai area. This research may be of great significance for an in-depth study of the metamorphism and tectonic evolution in the Su-Lu ultrahigh-pressure metamorphic belt.展开更多
Recently, a huge ultrahigh-pressure(UHP) metamorphic belt of oceanic-type has been recognized in southwestern(SW) Tianshan, China. Petrological studies show that the UHP metamorphic rocks of SW Tianshan orogenic belt ...Recently, a huge ultrahigh-pressure(UHP) metamorphic belt of oceanic-type has been recognized in southwestern(SW) Tianshan, China. Petrological studies show that the UHP metamorphic rocks of SW Tianshan orogenic belt include mafic eclogites and blueschists, pelitic garnet phengite schists, marbles and serpentinites. The well-preserved coesite inclusions were commonly found in eclogites, garnet phengite schists and marbles. Ti-clinohumite and Ti-chondrodite have been identified in UHP metamorphic serpentinites. Based on the PT pseudosection calculation and combined U-Pb zircon dating, the P-T-t path has been outlined as four stages: cold subduction to UHP conditions before^320 Ma whose peak ultrahigh pressure is about 30 kbar at 500 ℃, heating decompression from the Pmax to the Tmax stage before 305 Ma whose peak temperature is about 600 ℃ at 22 kbar, then the early cold exhumation from amphibolite eclogite facies to epidote-amphibolite facies metamorphism before 220 Ma and the last tectonic exhumation from epidote amphibolite facies to greenschist facies metamorphism. Combining with the syn-subduction arc-like 333-326 Ma granitic rocks and 280-260 Ma S-type granites in the coeval low-pressure and high-temperature(LP-HT) metamorphic belt, the tectonic evolution of Tianshan UHP metamorphic belt during late Cambrian to early Triassic has been proposed in this paper.展开更多
Up to now it is known that almost all ultrahigh-pressure (UHP) metamorphism of non-impact origin occurred in continent-continent collisional orogenic belt, as has been evidenced by many outcrops in the eastern hemisph...Up to now it is known that almost all ultrahigh-pressure (UHP) metamorphism of non-impact origin occurred in continent-continent collisional orogenic belt, as has been evidenced by many outcrops in the eastern hemisphere. UHP metamorphic rocks are represented by coesite- and diamond-bearing eclogites and eclogite facies metamorphic rocks formed at 650-800℃ and 2.6-3.5 GPa, and most of the protoliths of UHP rocks are volcanic-sedimentary sequences of continental crust. From these it may be deduced that deep subduction of continental crust may have occurred. However, UHP rocks are exposed on the surface or occur near the surface now, which implies that they have been exhumed from great depths. The mechanism of deep subduction of continental crust and subsequent exhumation has been a hot topic of the research on continental dynamics, but there are divergent views. The focus of the dispute is how deep continental crust is subducted so that UHP rocks can be formed and what mechanism causes it to be subducted to great depths and again exhumed to the shallow surface. Through an analysis of the continental process and mechanical boundary conditions of the Dabie collisional belt-an UHP metamorphic belt where the largest area of UHP rocks in the world is exposed, this paper discusses the variations of viscous stresses and average pressure in the viscous fluid caused by tectonism with rock physical properties and the contribution of the tectonic stresses to production of UHP. Calculation indicates that the anomalous stress state on the irregular boundary of a continental block may give rise to stress concentration and accumulation at local places (where the compressional stress may be 5-9 times higher than those in their surroundings). The tectonic stresses may account for 20-35% of the total UHP. So we may infer that the HP (nigh-pressure)-UHP rocks in the Dabie Mountains were formed at depths of 60-80 km. Thus the authors propose a new genetic model of UHP rocks-the point-collision model. This model conforms to the basic principles of the mechanics and also to the geologic records and process in the Dabie orogenic belt. It can explain why UHP rocks do nol exist along the entire length of the collisional orogen but occur in some particular positions. The authors also propose that the eastern and western corners of the Himalaya collision zone are typical point-collision areas and that almost all UHP metamorphism of continental crustal rocks occurred in the two particular positions.展开更多
The components and structures of lithosphere, inhomogeneous, are changing incessantly in different periods. Therefore, the state of load, called the pressure, in lithosphere is also incessantly changing. When the lith...The components and structures of lithosphere, inhomogeneous, are changing incessantly in different periods. Therefore, the state of load, called the pressure, in lithosphere is also incessantly changing. When the lithosphere volume remains the same, namely on the premise of isovolumes, the geobarmal gradient is: (d p /d h) v =( p / h) v +( p / T) v (d T /d h) v . If β =(d p /d h) v /( p / h) v is supposed, then β =1+ rg -1 C v (d T /d h) v . When the geothermal degree in (d T /d h) v is zero, then the pressure grade of lithosphere is equal to the lithostatic grade, which is the minimum value in the pressure grade of lithosphere. Suppose that the lithosphere is made only up of quartz, C v ≌ C p =0.782+5.718×10 -4 T -1.883×10 4 T -2 (J· g -1 · K -1 ) is obtained, which is the minimum one in lithospheric rock, and then the geothermal grade value of 20 ℃/km is calculated according to the geophysical transection data of Qinling Mountain orogeny. The results show that the high pressure and ultrahigh pressure eclogites in Jiangsu Province and Huangzhen, Dabie may, on the condition of incompletely isovolumes, occur in the depths of 17-40 km with the increase in geothermal temperature, whose values of β do not correspond to the theoretic value of 3.08.展开更多
Eclogite was firstly discovered at the Da Qaidam region (Yang,et al., 1998), and then in the Xitieshan and Dulan regions in 1999, constituting an over 350km long high\|pressure metamorphic belt in the northeastern Qin...Eclogite was firstly discovered at the Da Qaidam region (Yang,et al., 1998), and then in the Xitieshan and Dulan regions in 1999, constituting an over 350km long high\|pressure metamorphic belt in the northeastern Qinghai—Tibet plateau. Eclogites occur as pods in the garnet\|muscovite gneiss of the Dakendaban Group (or called Shaliuhe Group in Dulan) of Upper Proterozoic age. In general, the pods of eclogite vary in size; most of them are less than 20m×10m, some large ones up to about 100m×50m. The eclogite\|hosted gneiss is pale\|gray in color, consisting mainly plagioclase and quartz, and minor muscovite (5%~10% in vol.) and garnet (1%~2%). Some of the country rocks of eclogite are mica\|quartz\|(feldspar) schist, quartzite, and ultramafic rocks, the latter also occur in blocks.Over 50 pods were found in a belt of 10km×3km in the Da Qaidam region (No.1 location). Only a few pods of eclogite were found in the Xitieshan region in 1999 field expedition (No.2 location). Eclogite in Dulan occurs in the Proterozoic strata of Shaliuhe Group (same as the Dakendaban Group but with a different name). The eclogites in the Dulan region (No.3 location) expose about 10km wide in SN and an unknown length in EW, and can be subdivided into two belts, the North Eclogite Belt of Dulan (NEBD) and the South Eclogite Belt of Dulan (SEBD).展开更多
Study practice has proved that the ultrahigh pressure metamorphic rocks iu Dabieshan must have exPerienced botk the retrograde metumorphism and partial melting under decompression and amphibolite-facies conditions dur...Study practice has proved that the ultrahigh pressure metamorphic rocks iu Dabieshan must have exPerienced botk the retrograde metumorphism and partial melting under decompression and amphibolite-facies conditions during their exhumation from mantel depth to lower-middle crust.The retrometamorphism and partial melting of the ultrahigh pressure rocks in association with thermal state changing in the middle-lower crust, under amphibolite-facies conditions, are important physical and chemical processes. It would result in a great detrease in the integrated yield strength, and the enhancement of the de formabilitY or the rocks, promoting the transition from contractional (collision) to extensional defoemational regime. The statement of tbe retrometamorphism and partial melting of the ultrahigh pressure rocks has proved the in-site model for the ultrahigh pressure rocks in Dabieshan. It not only clarifies the evolutiou from the UHP eclogite to the surrounding gneissic rock (so called UHP gueiss) and to the garnet-beariug roliated granites (non-UHP country rocks), but also provides scientific arguments for the establiskment of the dynamic model of the exhumation of UHP metamorphic rocks in Dabiesban. In general, Purely conductive heat transfer from the crust itself is probably insurficient to produce temperature conditions for partial melting, and additional heat sources must have been present during partial melting. We infer that the partial melting and extensional flow are probably driveu by delamination and magmatic underplating of thickeued lithospkeric mantle following the continental oblique collision.展开更多
Recent investigations reveal that the ultrahigh-pressure metamorphic (UHPM) rocks in the Donghai region of East China underwent ductile and transitional ductile-brittle structural events during their exhumation. The e...Recent investigations reveal that the ultrahigh-pressure metamorphic (UHPM) rocks in the Donghai region of East China underwent ductile and transitional ductile-brittle structural events during their exhumation. The earlier ductile deformation took place under the condition of amphibolite facies and the later transitional ductile-brittle deformation under the condition of greenschist facies. The hanging walls moved southeastward during both of these two events. The 40Ar/39Ar dating of muscovites from muscovite-plagioclase schists in the Haizhou phosphorous mine, which are structurally overlain by UHPM rocks, yields a plateau age of 218.0±2.9 Ma and isochron age of 219.8Ma, indicating that the earlier event of the ampibolite-facies deformation probably took place about 220 Ma ago. The 40Ar/39Ar dating of oriented amphiboles parallel to the movement direction of the hanging wall on a decollement plane yields a plateau age of 213.1±0.3 Ma and isochron age of 213.4±4.1 Ma, probably representing the age of the later event. The dating of pegmatitic biotites and K-feldspars near the decollement plane from the eastern Fangshan area yield plateau ages of 203.4±0.3 Ma, 203.6±0.4 Ma and 204.8±2.2 Ma, and isochron ages of 204.0±2.0 Ma, 200.6±3.1 Ma and 204.0±5.0 Ma, respectively, implying that the rocks in the studied area had not been cooled down to closing temperature of the dated biotites and K-feldspars until the beginning of the Jurassic (about 204 Ma). The integration of these data with previous chronological ages on the ultrahigh-pressure metamorphism lead to a new inference on the exhumation of the UHPM rocks. The UHPM rocks in the area were exhumed at the rate of 3-4 km/Ma from the mantle (about 80-100 km below the earth's surface at about 240 Ma) to the lower crust (at the depth of about 20-30km at 220 Ma), and at the rate of 1-2 km/Ma to the middle crust (at the depth of about 15 km at 213 Ma), and then at the rate of less than 1 km/Ma to the upper crust about 10 km deep at about 204 Ma.展开更多
Lame modulus (λ) and shear modulus (μ) are among the most important, intrinsic, elastic constants of rocks. Using 7. and μ could be much more advantageous than using P- and S-wave velocities (Vp and Vs). Here...Lame modulus (λ) and shear modulus (μ) are among the most important, intrinsic, elastic constants of rocks. Using 7. and μ could be much more advantageous than using P- and S-wave velocities (Vp and Vs). Here we quantified these equivalent isotropic elastic moduli for 115 representative rocks from the ultrahigh pressure (UHP) metamorphic terrane of the Dabie-Sulu orogenic belt (China) and their variations with pressure (P), temperature (T), density (p), Vp, Vs and mineralogical composition. Both moduli increase nonlinearly and linearly with increasing pressure at low (〈200-300 MPa) and high (〉200-300 MPa) pressures, respectively. In the regime of high pressures, 7. and IX decrease quasi-linearly with increasing temperature with temperature derivatives dλ/dT and dμ/dT generally in the range of -10×10-3 to -1×10-3 GPa/℃. Dehydration of water-bearing minerals such as serpentine in peridotites and chlorite in retrograde eciogites results in an abrupt drop in 7. while μ remains almost unchanged. In Z-p, μ-p and 7.-IX plots, the main categories of UHP rocks can be characterized. Serpentinization leads to significant decreases in μ and 7. as serpentine has extremely low values of Z, μ and p. Eclogites, common mafic rocks (mafic gneiss, metagabbro and amphibolite), and felsic rocks (orthogneiss and paragneiss) have high, moderate and low μ and λ values, respectively. For pyroxenes and olivines, λ increases but μ decreases with increasing Fe/Mg ratios. For plagioclase feldspars, both Z and μ exhibit a significant positive correlation with anorthite content. SiO2-rich felsic rocks and quartzites are deviated remarkably from the general trend lines of the acid-intermediate-mafic rocks in Vs-p, μ-p, λ-Vp,λ-Vs and μ-λ diagrams because quartz has extremely low λ (-8.1 GPa) and p (2.65 g/cm3) but moderate μ (44.4 GPa) values. Increasing the contents of garnet, rutile, ilmenite and magnetite results in a significant increase in the λ and μ values of the UHP metamorphic rocks. However, either λ or μ is insensitive to the compositional variations for pyralspite (pyrope-almandine-spessartine) solution series. The results provide potentially improved constraints on characterization of crustal composition based on the elastic properties of rocks and in situ seismic data from deep continental roots.展开更多
Ultrahigh-pressure(UHP) metamorphic rocks are distinctive products of crustal deep subduction,and are mainly exposed in continental subduction-collision terranes. UHP slices of continental crust are usually involved...Ultrahigh-pressure(UHP) metamorphic rocks are distinctive products of crustal deep subduction,and are mainly exposed in continental subduction-collision terranes. UHP slices of continental crust are usually involved in multistage exhumation and partial melting, which has obvious influence on the rheological features of the rocks, and thus significantly affect the dynamic behavior of subducted slices. Moreover,partial melting of UHP rocks have significant influence on element mobility and related isotope behavior within continental subduction zones, which is in turn crucial to chemical differentiation of the continental crust and to crust-mantle interaction.Partial melting can occur before, during or after the peak metamorphism of UHP rocks. Post-peak decompression melting has been better constrained by remelting experiments; however, because of multiple stages of decompression, retrogression and deformation, evidence of former melts in UHP rocks is often erased. Field evidence is among the most reliable criteria to infer partial melting. Glass and nanogranitoid inclusions are generally considered conclusive petrographic evidence. The residual assemblages after melt extraction are also significant to indicate partial melting in some cases. Besides field and petrographic evidence, bulk-rock and zircon trace-element geochemical features are also effective tools for recognizing partial melting of UHP rocks. Phase equilibrium modeling is an important petrological tool that is becoming more and more popular in P-T estimation of the evolution of metamorphic rocks; by taking into account the activity model of silicate melt, it can predict when partial melting occurred if the P-T path of a given rock is provided.UHP silicate melt is commonly leucogranitic and peraluminous in composition with high SiO_2,low MgO, FeO, MnO, TiO_2 and CaO, and variable K_2 O and Na_2 O contents. Mineralogy of nanogranites found in UHP rocks mainly consists of plagioclase + K-feldspar + quartz, plagioclase being commonly albite-rich.Trace element pattern of the melt is characterized by significant enrichment of large ion lithophile elements(LILE), depletion of heavy rare earth elements(HREE) and high field strength elements(HFSE),indicating garnet and rutile stability in the residual assemblage. In eclogites, significant Mg-isotope fractionation occurs between garnet and phengite; therefore, Mg isotopes may become an effective indicator for partial melting of eclogites.展开更多
Coesite inclusions are found in kyanite from the Lanshantou eclogite in the Sulu ultrahigh-pressure (UHP) metamorphic belt. This discovery extends the stable region of kyanite to over 2.4 GPa. As an important UHP meta...Coesite inclusions are found in kyanite from the Lanshantou eclogite in the Sulu ultrahigh-pressure (UHP) metamorphic belt. This discovery extends the stable region of kyanite to over 2.4 GPa. As an important UHP metamorphic belt in China, the Sulu eclogite belt is the product of A-subduction induced by strong compression of the Yellow Sea terrane to the Jiaodong-northereastern Jiangsu terrane during the interaction of the Eurasian plate and Palaeo-Pacific plate in the Indosinian. It stretches about 350 km and contains over 1000 eclogite bodies. Most eclogites in this belt belong to Groups B and C in the classification of Coleman et al., and commonly contain kyanite, while the Lanshantou eclogite belongs to Group A and contains coesite. The MgO, CaO and FeO contents in garnet and pyroxene show regular variation from the core to the rim, which reveals the PTt paths of progressive metamorphism during the Early Mesozoic (240-200 Ma) and retrogressive metamorphism during the Late Mesozoic and Cenozoic exhumation.展开更多
Asthemaintectoniccomponentofthe Himalayan–Tibetan orogen,the Lhasa terrane has received much attention as it records the entire history of the orogeny.The occurrence of high pressure eclogite in the Sumdo complex in ...Asthemaintectoniccomponentofthe Himalayan–Tibetan orogen,the Lhasa terrane has received much attention as it records the entire history of the orogeny.The occurrence of high pressure eclogite in the Sumdo complex in central Lhasa terrane has a significant importance on the understanding of the Paleo-Tethys subduction and plate itineration processes in this area.The petrological,geochemical and geochronological data of eclogite and associated blueschist and garnet-bearing mica schist from Sumdo,Jilang and Bailang area have been briefly reviewed to explore the origin and metamorphic evolution of this suture.Eclogites from the Sumdo complex have experienced low temperature,high pressure to ultrahigh pressure metamorphism,revealing a fastsubduction and exhumation process in a typical oceanic subduction zone.The large P-T range between different eclogites in the literature may be affected by the big error of unappropriated using geothermobarometry and may also because of slices of subducted blocks derived from different depths juxtapose together during exhumation.By summarizing the U-Pb,Lu-Hf and Sm-Nd ages of eclogites,the eclogite facies metamorphism is likely to occur in early Triassic during 245-225 Ma,but not the previously accepted late Permian at ca.260 Ma by the reinterpretation of the former geochronological data from literature.The opening of Paleo-Tethys Ocean between the Lhasa terrane initiate prior to ca.280 Ma and ultimate closure to integrate the Lhasa terrane was no earlier than225 Ma and may triggered by the initial subduction of Bangong-Nujiang Tethys Ocean in the north.展开更多
The Sulu ultra-high pressure(UHP)metamorphic belt in Eastern China is well known as the eastern extension of the Qingling-Dabie orogenic belt formed by subduction and collision between the Sino-Korean and Yangtze crat...The Sulu ultra-high pressure(UHP)metamorphic belt in Eastern China is well known as the eastern extension of the Qingling-Dabie orogenic belt formed by subduction and collision between the Sino-Korean and Yangtze cratons.The main hole of the Chinese Continental Scientific Drilling(CCSD)project is located at the southern segment of the Sulu UHP metamorphic belt(34°25′N/118°40′E),about 17 km southwest of Donghai County.Integrated geophysical investigations using gravity,magnetic,deep展开更多
There are four units of high - pressure to ultrahigh - pressure metamorphism extending from south to north across the Tongbai - Dabie Mountains : the epidote- blueschist - fades unit , the low - temperature eclogite f...There are four units of high - pressure to ultrahigh - pressure metamorphism extending from south to north across the Tongbai - Dabie Mountains : the epidote- blueschist - fades unit , the low - temperature eclogite facies unit , the ultrahigh - pressure eclogite facies unit and the medium-temperature eclogite facies unit . The later two units were formed during the Caledonian subduction between the Tongbai - Dabie microplate and the North China plate ;the former two units are the products of Indosinian continental - continental subduction and collision between the Yangtze and the North China plates.展开更多
A wealth of retrogressive microstructures have been discovered from the UHP metamorphic rocks in Dabie orogenic belt, namely, the ultrahigh-pressure (URP) eclogites, jadeite quartzites and kyanite-zoisite-quartz vein....A wealth of retrogressive microstructures have been discovered from the UHP metamorphic rocks in Dabie orogenic belt, namely, the ultrahigh-pressure (URP) eclogites, jadeite quartzites and kyanite-zoisite-quartz vein. The most important are pseudomorphic replacements of UHP minerals like coesite, the corona reaction textures iuduced by solid-solid reactions as well as the corona and symplectites induced by reactions involving fluid. According to the textural relationships the sequence of mineral Paragenesis and the metamorphic stages in the UHP eclogites can be delineated; the mineral geobarothermometry of the various stages of retrograde metamorphism is studied and a clockwise, nearly isothermal decompressive metamorphic PT-trajectory for the UHP eclogites can be reconstructed. In terms of the PT-trajectory the two stage post collision uplirt and exhumation processes are reflected. When the UHP metumorphic rocks extruded to the lower-middle crust partial melting happened which bad in turn caused tke crustal extension and the further exhumation or the UHP metomorphic rocks. Based on the field strain analysis combined with geochronological data a scenario or post collision uplift aud exhumation model is presented.展开更多
A high pressure basic granulite ultramafics belt is found in the late Archaean gneisses of Laixi Laiyang Qixia district, east Shandong. This belt has previously been considered as another eclogite belt in Sulu ultra h...A high pressure basic granulite ultramafics belt is found in the late Archaean gneisses of Laixi Laiyang Qixia district, east Shandong. This belt has previously been considered as another eclogite belt in Sulu ultra high pressure(UHP) terrain. The typical high P granulite is characterized by mineral assemblages of three generations formed in different metamorphic episode respectively. The mineral assemblage of first episode is Grt(core)+Cpx+Pl, that of the second episode is Grt(rim)+Cpx+Opx+Pl+Amp+Q+Mt and that of the third episode is Cpx+Pl+Amp+Q+Mt. In first assemblage, the garnet porphyroblast is rich in grossular and pyrope component, and the coexisting Cpx is Al rich. Using mineral thermobarometer and Berman’s (1991) TWQ program, the P T conditions of three episodes are established, i.e. T=840℃~860℃, P>1.4GPa for first episode; T=720℃~780℃,P=0.8~1.2GPa for second episode and T=600℃~800℃,P=0.5~0.7GPa for the third episode.Considering the reaction texture, mineral Chemistry and PT estmations, a clockwise PTt path can be constructed, which shows post peak isothermal decompression at first and followed by a process of pressure and temperature decreasing. The mineral wholerock Sm Nd isochron age of the granulite is 1752Ma, which indicates its last thermal event during early middle Proterozoic stage. Therefore, it is concluded that the high pressure granulite and ultramafics of this belt represents the lower continental curst of the North China Craton during early Precambrian without any relationship to tectonic process of the Sulu UHP terrain.展开更多
Based upon fluid effects, retrograde metamorphism of eclogites in the Dabieregion can be divided into the fluid-poor, fluid-bearing and fluid-rich stages. The fluid-poor stageis marked by polymorphic inversion, recrys...Based upon fluid effects, retrograde metamorphism of eclogites in the Dabieregion can be divided into the fluid-poor, fluid-bearing and fluid-rich stages. The fluid-poor stageis marked by polymorphic inversion, recrystallization and exsolution of solid solutions, and isthought to represent eclogite-facies retrograde environments. The fluid-bearing stage is likely tohave occurred at the late stage of ecologite-facies diaphthorosis and is represented by kyaniteporphyroblasts, rutile, and sodic pyroxene in association with high-pressure hydrous minerals suchas phengite and zoisite (clinozoisite) without significant amount of hydrous minerals such asamphibole, epidote and biotite. The fluid-rich stage might have commenced concomitantly with loweramphibolite-facies diaphthoresis and persisted all the way towards the near-surface environment. Theproduct of this stage is characterized by plentiful hydrous and volatile-bearing phases.The dissemination-type rutile mineralizations in eclogites might have formed by preferentialshearing-induced pressure solution of gangue minerals at the fluid-bearing stage. The accompanyingvein rutile was precipitated from fluids of this stage after local transport and concentration, andmay hence represent proximal mobilization of titanium from the eclogite. Therefore, rutile veins canbe used as an exploration indicator for dissemination-type rutile deposits.展开更多
Shock effects of 93 Grove Mountains (GRV) ordinary chondrites were studied in this work, including fracture, various types of extinction, and recrystallization of silicates observed under optical microscopy. Shock-i...Shock effects of 93 Grove Mountains (GRV) ordinary chondrites were studied in this work, including fracture, various types of extinction, and recrystallization of silicates observed under optical microscopy. Shock-induced veins and pockets show various microtextures, decomposition and phase transformation of minerals. The confirmed high-pressure polymorphs of silicates are ringwoodite, majorite, pyroxene glass and maskelynite. Based on the shock effects and assemblages of high-pressure minerals, shock stages of all of 93 GRV ehondrites were classified. In comparison with literature, the Grove Mountains meteorites have a higher fraction (23 out of 93 ) of heavily shocked samples (S4--S5). Most of the heavily shocked meteorites are L group (22 out of 23), except for one H chondrite. The distinct shock metamorphism between H and. L groups may indicate different surface properties of their parent bodies. In addition, there is relationship between petrologic types and shock stages, with most heavily shocked samples observed in equilibrated ordinary chondrites ( especially Type 5 and 6).展开更多
The fatigue fracture behavior of four ultrahigh strength steels with different melting processes and therefore different inclusion sizes were studied by using a rotating bar two-point bending fatigue machine in the hi...The fatigue fracture behavior of four ultrahigh strength steels with different melting processes and therefore different inclusion sizes were studied by using a rotating bar two-point bending fatigue machine in the high-cycle regime up to 107 cycles of loading. The fracture surfaces were observed by field emission scanning electron microscopy (FESEM). It was found that the size of inclusion has significant effect on the fatigue behavior. For AtSI 4340 steel in which the inclusion size is smaller than 5.5 μm, all the fatigue cracks except one did not initiated from inclusion but from specimen surface and conventional S-N curve exists. For 65Si2MnWE and Aermet 100 steels in which the average inclusion sizes are 12.2 and 14.9 μm, respectively, fatigue cracks initiated from inclusions at lower stress amplitudes and stepwise S-N curves were observed. The S-N curve displays a continuous decline and fatigue failures originated from large oxide inclusion for 60Si2CrVA steel in which the average inclusion size is 44.4 pro. In the case of internal inclusion-induced fractures at cycles beyond about 1×10^6 for 65Si2MnWE and 60Si2CrVA steels, inclusion was always found inside the fish-eye and a granular bright facet (GBF) was observed in the vicinity around the inclusion. The GBF sizes increase with increasing the number of cycles to failure Nf in the long-life regime. The values of stress intensity factor range at crack initiation site for the GBF are almost constant with Nf, and are almost equal to that for the surface inclusion and the internal inclusion at cycles lower than about 1×10^6. Neither fish-eye nor GBF was observed for Aermet 100 steel in the present study.展开更多
文摘The most prominent feature of the extensional tectonic framework of post high pressure (HP) and ultrahigh pressure (UHP) metamorphism in Dabieshan is the development of the multi layered extension detachment zones surrounding the core of the Luotian dome, and the separation of the UHP, HP and epidote blueschist units by the detachment zones, which form the vertically stacking sheet like slices of the HP and UHP metamorphic rocks. From the core outwards, exist the HP and UHP rock barren Dabie complex, UHP unit, HP unit and epidote blueschist unit. The extension tectonics of post HP and UHP metamorphic event constrain the distribution and present configuration of the HP and UHP metamorphic rocks, and the extensional tectonic framework bears some similarities to the Cordillera metamorphic core complex. It is suggested that partial melting happened in the Dabie gneiss complex (DGC) and UHP unit contemporaneously with the extrusion of UHP metamorphic rocks into the lower-middle crust. The formation and emplacement of the migmatite and granites are the response to the change in thermal state, facilitating the transfer from the compressive regime to extensional regime in the crust. The large scale crustal extension and uplift and the accompanying anatexis in Dabieshan are probably related to the delamination and magmatic underplating in the mantle and the lower crust.
文摘In the gneisses from the drillhole ZK2304 of the Donghai area, there have been preserved high- and ultrahigh-pressure metamorphic mineral assemblages, a series of complicated retrogressive textures and relevant metamorphic reactions. In addition to garnet, jadeititic-clinopyroxene and rutile, other peak stage (M2) minerals in some gneisses include phengite, aragonite and coesite or quartz pseudomorphs after coesite. The typical peak-stage mineral assemblages in gneisses are characterized by garnet + jadeitic-clinopyroxene + rutile + coesite, garnet + jadeitic-clinopyroxene + phengite + rutile ± coesite and garnet + jadeitic-clinopyroxene + aragonite + rutile ± coesite. The grossular content (Gro) in garnet is high and may reach 50. 1 mol%. The SiO2 content of phengite ranges from 54.37% to 54.84% with 3.54-3.57 p.f.u. Quartz pseudomorphs after coesite occur as inclusions in garnet.The gneisses of the Donghai area have been subjected to multistage recrystallization and exhibit a closewise P-T evolutional path characterized by the near-isothermal decompression. The inclusion assemblage (Hb+Ep+Bi+Pl+Qz) within garnet and other minerals has recorded a pre-peak stage (Mi) epidote amphibole fades metamorphic event. High- and ultrahigh-pressure peak metamorphism (M2) took place at T=750-860℃ and P>2.7 GPa. The symplectitic assemblages after garnet, jadeitic-clinopyroxene and rutile imply a near-isothermal decompression metamorphism (M3, M4) during the rapid exhumation. Several lines of evidence of petrography and metamorphic reactions indicate that both gneisses and eclogites have experienced ultrahigh-pressure metamorphism in the Donghai area. This research may be of great significance for an in-depth study of the metamorphism and tectonic evolution in the Su-Lu ultrahigh-pressure metamorphic belt.
文摘Recently, a huge ultrahigh-pressure(UHP) metamorphic belt of oceanic-type has been recognized in southwestern(SW) Tianshan, China. Petrological studies show that the UHP metamorphic rocks of SW Tianshan orogenic belt include mafic eclogites and blueschists, pelitic garnet phengite schists, marbles and serpentinites. The well-preserved coesite inclusions were commonly found in eclogites, garnet phengite schists and marbles. Ti-clinohumite and Ti-chondrodite have been identified in UHP metamorphic serpentinites. Based on the PT pseudosection calculation and combined U-Pb zircon dating, the P-T-t path has been outlined as four stages: cold subduction to UHP conditions before^320 Ma whose peak ultrahigh pressure is about 30 kbar at 500 ℃, heating decompression from the Pmax to the Tmax stage before 305 Ma whose peak temperature is about 600 ℃ at 22 kbar, then the early cold exhumation from amphibolite eclogite facies to epidote-amphibolite facies metamorphism before 220 Ma and the last tectonic exhumation from epidote amphibolite facies to greenschist facies metamorphism. Combining with the syn-subduction arc-like 333-326 Ma granitic rocks and 280-260 Ma S-type granites in the coeval low-pressure and high-temperature(LP-HT) metamorphic belt, the tectonic evolution of Tianshan UHP metamorphic belt during late Cambrian to early Triassic has been proposed in this paper.
基金the keyfundamentalgeologicalresearch project (No.9501102-3) the Ninth Five-Year Plan supported by the Ministry of Land and Resources a projectsupported by National Natural Science Foundation ofChina grant 19972064.
文摘Up to now it is known that almost all ultrahigh-pressure (UHP) metamorphism of non-impact origin occurred in continent-continent collisional orogenic belt, as has been evidenced by many outcrops in the eastern hemisphere. UHP metamorphic rocks are represented by coesite- and diamond-bearing eclogites and eclogite facies metamorphic rocks formed at 650-800℃ and 2.6-3.5 GPa, and most of the protoliths of UHP rocks are volcanic-sedimentary sequences of continental crust. From these it may be deduced that deep subduction of continental crust may have occurred. However, UHP rocks are exposed on the surface or occur near the surface now, which implies that they have been exhumed from great depths. The mechanism of deep subduction of continental crust and subsequent exhumation has been a hot topic of the research on continental dynamics, but there are divergent views. The focus of the dispute is how deep continental crust is subducted so that UHP rocks can be formed and what mechanism causes it to be subducted to great depths and again exhumed to the shallow surface. Through an analysis of the continental process and mechanical boundary conditions of the Dabie collisional belt-an UHP metamorphic belt where the largest area of UHP rocks in the world is exposed, this paper discusses the variations of viscous stresses and average pressure in the viscous fluid caused by tectonism with rock physical properties and the contribution of the tectonic stresses to production of UHP. Calculation indicates that the anomalous stress state on the irregular boundary of a continental block may give rise to stress concentration and accumulation at local places (where the compressional stress may be 5-9 times higher than those in their surroundings). The tectonic stresses may account for 20-35% of the total UHP. So we may infer that the HP (nigh-pressure)-UHP rocks in the Dabie Mountains were formed at depths of 60-80 km. Thus the authors propose a new genetic model of UHP rocks-the point-collision model. This model conforms to the basic principles of the mechanics and also to the geologic records and process in the Dabie orogenic belt. It can explain why UHP rocks do nol exist along the entire length of the collisional orogen but occur in some particular positions. The authors also propose that the eastern and western corners of the Himalaya collision zone are typical point-collision areas and that almost all UHP metamorphism of continental crustal rocks occurred in the two particular positions.
文摘The components and structures of lithosphere, inhomogeneous, are changing incessantly in different periods. Therefore, the state of load, called the pressure, in lithosphere is also incessantly changing. When the lithosphere volume remains the same, namely on the premise of isovolumes, the geobarmal gradient is: (d p /d h) v =( p / h) v +( p / T) v (d T /d h) v . If β =(d p /d h) v /( p / h) v is supposed, then β =1+ rg -1 C v (d T /d h) v . When the geothermal degree in (d T /d h) v is zero, then the pressure grade of lithosphere is equal to the lithostatic grade, which is the minimum value in the pressure grade of lithosphere. Suppose that the lithosphere is made only up of quartz, C v ≌ C p =0.782+5.718×10 -4 T -1.883×10 4 T -2 (J· g -1 · K -1 ) is obtained, which is the minimum one in lithospheric rock, and then the geothermal grade value of 20 ℃/km is calculated according to the geophysical transection data of Qinling Mountain orogeny. The results show that the high pressure and ultrahigh pressure eclogites in Jiangsu Province and Huangzhen, Dabie may, on the condition of incompletely isovolumes, occur in the depths of 17-40 km with the increase in geothermal temperature, whose values of β do not correspond to the theoretic value of 3.08.
文摘Eclogite was firstly discovered at the Da Qaidam region (Yang,et al., 1998), and then in the Xitieshan and Dulan regions in 1999, constituting an over 350km long high\|pressure metamorphic belt in the northeastern Qinghai—Tibet plateau. Eclogites occur as pods in the garnet\|muscovite gneiss of the Dakendaban Group (or called Shaliuhe Group in Dulan) of Upper Proterozoic age. In general, the pods of eclogite vary in size; most of them are less than 20m×10m, some large ones up to about 100m×50m. The eclogite\|hosted gneiss is pale\|gray in color, consisting mainly plagioclase and quartz, and minor muscovite (5%~10% in vol.) and garnet (1%~2%). Some of the country rocks of eclogite are mica\|quartz\|(feldspar) schist, quartzite, and ultramafic rocks, the latter also occur in blocks.Over 50 pods were found in a belt of 10km×3km in the Da Qaidam region (No.1 location). Only a few pods of eclogite were found in the Xitieshan region in 1999 field expedition (No.2 location). Eclogite in Dulan occurs in the Proterozoic strata of Shaliuhe Group (same as the Dakendaban Group but with a different name). The eclogites in the Dulan region (No.3 location) expose about 10km wide in SN and an unknown length in EW, and can be subdivided into two belts, the North Eclogite Belt of Dulan (NEBD) and the South Eclogite Belt of Dulan (SEBD).
文摘Study practice has proved that the ultrahigh pressure metamorphic rocks iu Dabieshan must have exPerienced botk the retrograde metumorphism and partial melting under decompression and amphibolite-facies conditions during their exhumation from mantel depth to lower-middle crust.The retrometamorphism and partial melting of the ultrahigh pressure rocks in association with thermal state changing in the middle-lower crust, under amphibolite-facies conditions, are important physical and chemical processes. It would result in a great detrease in the integrated yield strength, and the enhancement of the de formabilitY or the rocks, promoting the transition from contractional (collision) to extensional defoemational regime. The statement of tbe retrometamorphism and partial melting of the ultrahigh pressure rocks has proved the in-site model for the ultrahigh pressure rocks in Dabieshan. It not only clarifies the evolutiou from the UHP eclogite to the surrounding gneissic rock (so called UHP gueiss) and to the garnet-beariug roliated granites (non-UHP country rocks), but also provides scientific arguments for the establiskment of the dynamic model of the exhumation of UHP metamorphic rocks in Dabiesban. In general, Purely conductive heat transfer from the crust itself is probably insurficient to produce temperature conditions for partial melting, and additional heat sources must have been present during partial melting. We infer that the partial melting and extensional flow are probably driveu by delamination and magmatic underplating of thickeued lithospkeric mantle following the continental oblique collision.
文摘Recent investigations reveal that the ultrahigh-pressure metamorphic (UHPM) rocks in the Donghai region of East China underwent ductile and transitional ductile-brittle structural events during their exhumation. The earlier ductile deformation took place under the condition of amphibolite facies and the later transitional ductile-brittle deformation under the condition of greenschist facies. The hanging walls moved southeastward during both of these two events. The 40Ar/39Ar dating of muscovites from muscovite-plagioclase schists in the Haizhou phosphorous mine, which are structurally overlain by UHPM rocks, yields a plateau age of 218.0±2.9 Ma and isochron age of 219.8Ma, indicating that the earlier event of the ampibolite-facies deformation probably took place about 220 Ma ago. The 40Ar/39Ar dating of oriented amphiboles parallel to the movement direction of the hanging wall on a decollement plane yields a plateau age of 213.1±0.3 Ma and isochron age of 213.4±4.1 Ma, probably representing the age of the later event. The dating of pegmatitic biotites and K-feldspars near the decollement plane from the eastern Fangshan area yield plateau ages of 203.4±0.3 Ma, 203.6±0.4 Ma and 204.8±2.2 Ma, and isochron ages of 204.0±2.0 Ma, 200.6±3.1 Ma and 204.0±5.0 Ma, respectively, implying that the rocks in the studied area had not been cooled down to closing temperature of the dated biotites and K-feldspars until the beginning of the Jurassic (about 204 Ma). The integration of these data with previous chronological ages on the ultrahigh-pressure metamorphism lead to a new inference on the exhumation of the UHPM rocks. The UHPM rocks in the area were exhumed at the rate of 3-4 km/Ma from the mantle (about 80-100 km below the earth's surface at about 240 Ma) to the lower crust (at the depth of about 20-30km at 220 Ma), and at the rate of 1-2 km/Ma to the middle crust (at the depth of about 15 km at 213 Ma), and then at the rate of less than 1 km/Ma to the upper crust about 10 km deep at about 204 Ma.
基金supported by the Sino Probe-deep exploration in Ministry of land and Resources of China(Sino Probe-07)the knowledge Innovation Program from Guangzhou Institute of Geochemistry,the Chinese Academy of Sciences(GIGCX-09-02)+1 种基金This is contribution No.IS-1386 from GIGCASthe Natural Sciences and Engineering Council of Canada and the Chinese Academy of Geological Sciences for the discovery and research grants(No.1212011121274)
文摘Lame modulus (λ) and shear modulus (μ) are among the most important, intrinsic, elastic constants of rocks. Using 7. and μ could be much more advantageous than using P- and S-wave velocities (Vp and Vs). Here we quantified these equivalent isotropic elastic moduli for 115 representative rocks from the ultrahigh pressure (UHP) metamorphic terrane of the Dabie-Sulu orogenic belt (China) and their variations with pressure (P), temperature (T), density (p), Vp, Vs and mineralogical composition. Both moduli increase nonlinearly and linearly with increasing pressure at low (〈200-300 MPa) and high (〉200-300 MPa) pressures, respectively. In the regime of high pressures, 7. and IX decrease quasi-linearly with increasing temperature with temperature derivatives dλ/dT and dμ/dT generally in the range of -10×10-3 to -1×10-3 GPa/℃. Dehydration of water-bearing minerals such as serpentine in peridotites and chlorite in retrograde eciogites results in an abrupt drop in 7. while μ remains almost unchanged. In Z-p, μ-p and 7.-IX plots, the main categories of UHP rocks can be characterized. Serpentinization leads to significant decreases in μ and 7. as serpentine has extremely low values of Z, μ and p. Eclogites, common mafic rocks (mafic gneiss, metagabbro and amphibolite), and felsic rocks (orthogneiss and paragneiss) have high, moderate and low μ and λ values, respectively. For pyroxenes and olivines, λ increases but μ decreases with increasing Fe/Mg ratios. For plagioclase feldspars, both Z and μ exhibit a significant positive correlation with anorthite content. SiO2-rich felsic rocks and quartzites are deviated remarkably from the general trend lines of the acid-intermediate-mafic rocks in Vs-p, μ-p, λ-Vp,λ-Vs and μ-λ diagrams because quartz has extremely low λ (-8.1 GPa) and p (2.65 g/cm3) but moderate μ (44.4 GPa) values. Increasing the contents of garnet, rutile, ilmenite and magnetite results in a significant increase in the λ and μ values of the UHP metamorphic rocks. However, either λ or μ is insensitive to the compositional variations for pyralspite (pyrope-almandine-spessartine) solution series. The results provide potentially improved constraints on characterization of crustal composition based on the elastic properties of rocks and in situ seismic data from deep continental roots.
基金financially supported by the National Basic Research Program of China (Grant No. 2015CB856104)the National Natural Science Foundation of China (Grant No. 41273036)
文摘Ultrahigh-pressure(UHP) metamorphic rocks are distinctive products of crustal deep subduction,and are mainly exposed in continental subduction-collision terranes. UHP slices of continental crust are usually involved in multistage exhumation and partial melting, which has obvious influence on the rheological features of the rocks, and thus significantly affect the dynamic behavior of subducted slices. Moreover,partial melting of UHP rocks have significant influence on element mobility and related isotope behavior within continental subduction zones, which is in turn crucial to chemical differentiation of the continental crust and to crust-mantle interaction.Partial melting can occur before, during or after the peak metamorphism of UHP rocks. Post-peak decompression melting has been better constrained by remelting experiments; however, because of multiple stages of decompression, retrogression and deformation, evidence of former melts in UHP rocks is often erased. Field evidence is among the most reliable criteria to infer partial melting. Glass and nanogranitoid inclusions are generally considered conclusive petrographic evidence. The residual assemblages after melt extraction are also significant to indicate partial melting in some cases. Besides field and petrographic evidence, bulk-rock and zircon trace-element geochemical features are also effective tools for recognizing partial melting of UHP rocks. Phase equilibrium modeling is an important petrological tool that is becoming more and more popular in P-T estimation of the evolution of metamorphic rocks; by taking into account the activity model of silicate melt, it can predict when partial melting occurred if the P-T path of a given rock is provided.UHP silicate melt is commonly leucogranitic and peraluminous in composition with high SiO_2,low MgO, FeO, MnO, TiO_2 and CaO, and variable K_2 O and Na_2 O contents. Mineralogy of nanogranites found in UHP rocks mainly consists of plagioclase + K-feldspar + quartz, plagioclase being commonly albite-rich.Trace element pattern of the melt is characterized by significant enrichment of large ion lithophile elements(LILE), depletion of heavy rare earth elements(HREE) and high field strength elements(HFSE),indicating garnet and rutile stability in the residual assemblage. In eclogites, significant Mg-isotope fractionation occurs between garnet and phengite; therefore, Mg isotopes may become an effective indicator for partial melting of eclogites.
文摘Coesite inclusions are found in kyanite from the Lanshantou eclogite in the Sulu ultrahigh-pressure (UHP) metamorphic belt. This discovery extends the stable region of kyanite to over 2.4 GPa. As an important UHP metamorphic belt in China, the Sulu eclogite belt is the product of A-subduction induced by strong compression of the Yellow Sea terrane to the Jiaodong-northereastern Jiangsu terrane during the interaction of the Eurasian plate and Palaeo-Pacific plate in the Indosinian. It stretches about 350 km and contains over 1000 eclogite bodies. Most eclogites in this belt belong to Groups B and C in the classification of Coleman et al., and commonly contain kyanite, while the Lanshantou eclogite belongs to Group A and contains coesite. The MgO, CaO and FeO contents in garnet and pyroxene show regular variation from the core to the rim, which reveals the PTt paths of progressive metamorphism during the Early Mesozoic (240-200 Ma) and retrogressive metamorphism during the Late Mesozoic and Cenozoic exhumation.
文摘Asthemaintectoniccomponentofthe Himalayan–Tibetan orogen,the Lhasa terrane has received much attention as it records the entire history of the orogeny.The occurrence of high pressure eclogite in the Sumdo complex in central Lhasa terrane has a significant importance on the understanding of the Paleo-Tethys subduction and plate itineration processes in this area.The petrological,geochemical and geochronological data of eclogite and associated blueschist and garnet-bearing mica schist from Sumdo,Jilang and Bailang area have been briefly reviewed to explore the origin and metamorphic evolution of this suture.Eclogites from the Sumdo complex have experienced low temperature,high pressure to ultrahigh pressure metamorphism,revealing a fastsubduction and exhumation process in a typical oceanic subduction zone.The large P-T range between different eclogites in the literature may be affected by the big error of unappropriated using geothermobarometry and may also because of slices of subducted blocks derived from different depths juxtapose together during exhumation.By summarizing the U-Pb,Lu-Hf and Sm-Nd ages of eclogites,the eclogite facies metamorphism is likely to occur in early Triassic during 245-225 Ma,but not the previously accepted late Permian at ca.260 Ma by the reinterpretation of the former geochronological data from literature.The opening of Paleo-Tethys Ocean between the Lhasa terrane initiate prior to ca.280 Ma and ultimate closure to integrate the Lhasa terrane was no earlier than225 Ma and may triggered by the initial subduction of Bangong-Nujiang Tethys Ocean in the north.
文摘The Sulu ultra-high pressure(UHP)metamorphic belt in Eastern China is well known as the eastern extension of the Qingling-Dabie orogenic belt formed by subduction and collision between the Sino-Korean and Yangtze cratons.The main hole of the Chinese Continental Scientific Drilling(CCSD)project is located at the southern segment of the Sulu UHP metamorphic belt(34°25′N/118°40′E),about 17 km southwest of Donghai County.Integrated geophysical investigations using gravity,magnetic,deep
基金The study is sponsored by the key project of National Natural Sci-ence Foundation of China and the Laboratory of Crust-Mantle Constitution, Recycling and Dynamics
文摘There are four units of high - pressure to ultrahigh - pressure metamorphism extending from south to north across the Tongbai - Dabie Mountains : the epidote- blueschist - fades unit , the low - temperature eclogite facies unit , the ultrahigh - pressure eclogite facies unit and the medium-temperature eclogite facies unit . The later two units were formed during the Caledonian subduction between the Tongbai - Dabie microplate and the North China plate ;the former two units are the products of Indosinian continental - continental subduction and collision between the Yangtze and the North China plates.
文摘A wealth of retrogressive microstructures have been discovered from the UHP metamorphic rocks in Dabie orogenic belt, namely, the ultrahigh-pressure (URP) eclogites, jadeite quartzites and kyanite-zoisite-quartz vein. The most important are pseudomorphic replacements of UHP minerals like coesite, the corona reaction textures iuduced by solid-solid reactions as well as the corona and symplectites induced by reactions involving fluid. According to the textural relationships the sequence of mineral Paragenesis and the metamorphic stages in the UHP eclogites can be delineated; the mineral geobarothermometry of the various stages of retrograde metamorphism is studied and a clockwise, nearly isothermal decompressive metamorphic PT-trajectory for the UHP eclogites can be reconstructed. In terms of the PT-trajectory the two stage post collision uplirt and exhumation processes are reflected. When the UHP metumorphic rocks extruded to the lower-middle crust partial melting happened which bad in turn caused tke crustal extension and the further exhumation or the UHP metomorphic rocks. Based on the field strain analysis combined with geochronological data a scenario or post collision uplift aud exhumation model is presented.
文摘A high pressure basic granulite ultramafics belt is found in the late Archaean gneisses of Laixi Laiyang Qixia district, east Shandong. This belt has previously been considered as another eclogite belt in Sulu ultra high pressure(UHP) terrain. The typical high P granulite is characterized by mineral assemblages of three generations formed in different metamorphic episode respectively. The mineral assemblage of first episode is Grt(core)+Cpx+Pl, that of the second episode is Grt(rim)+Cpx+Opx+Pl+Amp+Q+Mt and that of the third episode is Cpx+Pl+Amp+Q+Mt. In first assemblage, the garnet porphyroblast is rich in grossular and pyrope component, and the coexisting Cpx is Al rich. Using mineral thermobarometer and Berman’s (1991) TWQ program, the P T conditions of three episodes are established, i.e. T=840℃~860℃, P>1.4GPa for first episode; T=720℃~780℃,P=0.8~1.2GPa for second episode and T=600℃~800℃,P=0.5~0.7GPa for the third episode.Considering the reaction texture, mineral Chemistry and PT estmations, a clockwise PTt path can be constructed, which shows post peak isothermal decompression at first and followed by a process of pressure and temperature decreasing. The mineral wholerock Sm Nd isochron age of the granulite is 1752Ma, which indicates its last thermal event during early middle Proterozoic stage. Therefore, it is concluded that the high pressure granulite and ultramafics of this belt represents the lower continental curst of the North China Craton during early Precambrian without any relationship to tectonic process of the Sulu UHP terrain.
文摘Based upon fluid effects, retrograde metamorphism of eclogites in the Dabieregion can be divided into the fluid-poor, fluid-bearing and fluid-rich stages. The fluid-poor stageis marked by polymorphic inversion, recrystallization and exsolution of solid solutions, and isthought to represent eclogite-facies retrograde environments. The fluid-bearing stage is likely tohave occurred at the late stage of ecologite-facies diaphthorosis and is represented by kyaniteporphyroblasts, rutile, and sodic pyroxene in association with high-pressure hydrous minerals suchas phengite and zoisite (clinozoisite) without significant amount of hydrous minerals such asamphibole, epidote and biotite. The fluid-rich stage might have commenced concomitantly with loweramphibolite-facies diaphthoresis and persisted all the way towards the near-surface environment. Theproduct of this stage is characterized by plentiful hydrous and volatile-bearing phases.The dissemination-type rutile mineralizations in eclogites might have formed by preferentialshearing-induced pressure solution of gangue minerals at the fluid-bearing stage. The accompanyingvein rutile was precipitated from fluids of this stage after local transport and concentration, andmay hence represent proximal mobilization of titanium from the eclogite. Therefore, rutile veins canbe used as an exploration indicator for dissemination-type rutile deposits.
基金supported by the Knowledge Innovation Program of the Chinese Academy of Sciences(kzcx2-yw-110,KZCX2-YW-Q08)
文摘Shock effects of 93 Grove Mountains (GRV) ordinary chondrites were studied in this work, including fracture, various types of extinction, and recrystallization of silicates observed under optical microscopy. Shock-induced veins and pockets show various microtextures, decomposition and phase transformation of minerals. The confirmed high-pressure polymorphs of silicates are ringwoodite, majorite, pyroxene glass and maskelynite. Based on the shock effects and assemblages of high-pressure minerals, shock stages of all of 93 GRV ehondrites were classified. In comparison with literature, the Grove Mountains meteorites have a higher fraction (23 out of 93 ) of heavily shocked samples (S4--S5). Most of the heavily shocked meteorites are L group (22 out of 23), except for one H chondrite. The distinct shock metamorphism between H and. L groups may indicate different surface properties of their parent bodies. In addition, there is relationship between petrologic types and shock stages, with most heavily shocked samples observed in equilibrated ordinary chondrites ( especially Type 5 and 6).
基金the National Key Basic Research and Development Program of China under grant No.2004CB619104.
文摘The fatigue fracture behavior of four ultrahigh strength steels with different melting processes and therefore different inclusion sizes were studied by using a rotating bar two-point bending fatigue machine in the high-cycle regime up to 107 cycles of loading. The fracture surfaces were observed by field emission scanning electron microscopy (FESEM). It was found that the size of inclusion has significant effect on the fatigue behavior. For AtSI 4340 steel in which the inclusion size is smaller than 5.5 μm, all the fatigue cracks except one did not initiated from inclusion but from specimen surface and conventional S-N curve exists. For 65Si2MnWE and Aermet 100 steels in which the average inclusion sizes are 12.2 and 14.9 μm, respectively, fatigue cracks initiated from inclusions at lower stress amplitudes and stepwise S-N curves were observed. The S-N curve displays a continuous decline and fatigue failures originated from large oxide inclusion for 60Si2CrVA steel in which the average inclusion size is 44.4 pro. In the case of internal inclusion-induced fractures at cycles beyond about 1×10^6 for 65Si2MnWE and 60Si2CrVA steels, inclusion was always found inside the fish-eye and a granular bright facet (GBF) was observed in the vicinity around the inclusion. The GBF sizes increase with increasing the number of cycles to failure Nf in the long-life regime. The values of stress intensity factor range at crack initiation site for the GBF are almost constant with Nf, and are almost equal to that for the surface inclusion and the internal inclusion at cycles lower than about 1×10^6. Neither fish-eye nor GBF was observed for Aermet 100 steel in the present study.